Xe nâng dầu TCM 2.5 tấn ✅ Ngồi lái ✅ Chiều cao nâng 3000mm ✅ Nhập khẩu chính hãng Nhật Bản ✅ Liên hệ 090 369 56 88 nhận báo giá.
Xem thêm: https://samcovina.vn/san-pham/xe-nang-dau-tcm-2-5-tan/
2. ENHANCED OPERATOR COMFORT
SUBSTANTIALLY REDUCED VIBRATION BY
ADOPTING DUAL-FLOATING SYSTEMS FOR BOTH
THE ENGINE AND HOOD
Minimizes the transfer of vibration to the operator, with four-
point rubber cushion absorbers between the seat and engine
and its transmission. Moreover, use of the same four-point
suspension adopted in the hood, realizing a dual effect in
reducing vehicle vibrations.
GENERAL
EXPANSIVE FLOOR SPACE FOR EASIER FOOT
MANEUVERING
An amazing 45% increase in floor space by placing tilt cylinders
under the floor. This gives a smooth footwell in addition to easy
entry and exit.
MORE CONVENIENT PARKING
LEVER
The lever is positioned to the right of
the steering wheel for easier entry
and exit.
A double-action brake release on the
lever further improves safety.
EXTRA ENTRY AND EXIT FROM AN
EXTRA-WIDE STEP -- 55% WIDER
The secure step with enlarged foot
space enables greater comfort and less
fatigue while entering and exiting the
vehicle.
MULTIFUNCTIONAL SUSPENSION SEAT (available for
1.5/1.8 ton high power & 2/3.5 ton models)
Features include reinforced driver support, reduced vibration,
operator weight balance adjusting, forward and backward
reclining, a rear utility pocket and seat belt.
RESIN SCREEN
The resin screen on the overhead
guard enables comfortable outdoor
operation in wet weather.
3. SUPERIOR MANEUVERABILITY AND ASSURED SAFETY
INNOVATIVE FORK-LANDING MECHANISM
(available for wide view two-stage mast)
The fork-lowering speed decelerates at a height of
approximately 150mm above the ground enabling accurate
placement of the forks into the load fork pockets or pallet.
REDUCED FATIGUE DUE TO A SEMI-CIRCULAR STEERING WHEEL
A smaller diameter (300mm outer diameter) steering wheel gives
improved vehicle maneuverability. In addition, this compact steering wheel
makes it much easier to get on and off the truck.
METER PANEL OPTIMALLY
LOCATED TO THE RIGHT
OF THE DRIVER’S SEAT
The meter panel is located
on the top right side of
the dashboard for easier
readability by the operator.
MULTI-CONE SYNCHRONIZER SHIFT LEVERS
The newly adopted levers enable smooth shifting from
both forward and
reverse (available for
manual transmission
models).
ANTI-ROLL MECHANISM FOR ASSURED SAFETY DURING
TURNING (available for 2-3.5 ton models)
Warning: This system does not guarantee accident avoidance or
prevention of vehicle overturning.
NEUTRAL SAFETY MECHANISM
This feature enhances safety of
operation. The engine cannot be
started unless the change lever is
in the neutral position.
HIGH-MOUNT REAR COMBINATION
LIGHTS
The rear combination lights are installed
on the top left and right sides of the
overhead guard for easier recognition by
on-site workers.
ANTI-SLIP MAT ON THE
HOOD
A rubber strip is
attached to the hood to
prevent slippage while
stepping on and off.
METER PANEL WITH LCD
INDICATORS
The LCD has a longer life and is
easy to read even during daylight
shift operation.
EXCELLENT OPERATOR VISIBILITY
• Wider forward visibility
Clearer visibility of the fork tips
-- 50% improvement over other
current models. This achievement
was made possible by lowering
the dashboard by 70mm and the
tie bar by 190mm. A remarkable
improvement of the forward view
along with quicker recognition of
the fork position. An operator-
friendly design with assured safety,
high efficiency and relaxing feel.
• Amazing backward visibility
Reshaped counter weight for better rearview
sight. The round shape of the rear top end of the
counterweight
substantially
improves
visibility for
increased
safety during
backward
movement.
4. RUGGEDNESS AND INCREASED DURABILITY
5% IMPROVED FRONT AND REAR STABILITY RATIO
(available for 2-3.5 ton models)
Stable and more consistent cargo handling as well as travel
due to an improved stability ratio.
STURDIER MAST
Minimized distortion of the mast by redesigned
positioning the mast supports and tilt
cylinders. TCM’s traditional robust mast was
further upgraded by adopting sturdier tie bars,
while maintaining a wide range of viewing
angles.
IMPROVED DURABILITY WITH LUBRICANT
FILLED LIFT CYLINDER
Oil filled lift cylinders give improved durability.
(available for 2-3.5 ton models)
SINGLE-PIECE HEADGUARD
The front and rear pillars as well
as roof are all welded together in
a single-piece construction to give
additional strenght to the entire
structure.
COOLER RUNNING THROUGH
IMPROVED AIRFLOW
Optimal positioning of the fan, radiator
and muffler has reduced the operating
coolant temperature (gasoline models).
The operating temperature of the
hydraulic oil has been reduced, also
by 10°C by upgrading the mechanical
components and circuitry.
TCM TRANSMISSIONS
TCM designed and developped
these transmissions for quiet
operation and maximum
durability, and TCM builds them
to insure the highest quality.
TCM STEERING AXLES
Also a new TCM design, the steer axle
has been strengthened and improved for
durability in demanding applications.
5. EASY MAINTENANCE AND ENVIRONMENT FRIENDLINESS
DETACHABLE SIDE COVERS FOR CONVENIENT
INSPECTION AND SIMPLE MAINTENANCE
Inspection and maintenance can more easily be performed due
to one-touch detachable side covers and a wide-opening hood.
INTEGRAL LAYOUT OF ELECTRICAL PARTS AND OTHER
SYSTEM DEVICES
Maintenance inspections can be performed more easily, as
electrical parts such as the fuse box, relay and battery are
neatly integrated into a conveniently compact area.
NEW ENGINES, COMPLIANT WITH WORLDWIDE 2nd
STAGE EMISSION REGULATIONS
Powerful, yet appropriate, diesel engines, compliant with
stringent global emissions regulations.
ONE-PIECE
FLOORBOARD
Gives more convenient
inspection and easier
maintenance, as the
one-piece floorboard
unit is easily detachable
without using any tools.
NEW OPTIONAL EQUIPMENT
• Three-stage mast with four-
cylinder mechanism (available
for 2-3 ton models)
The cylinders are
symmetrically located to the
left and right for improved
forward visibility.
• Integral Side Shifter
A major improvement in the
integral side shifter ensures
less load loss and improved
forward visibility.
• Low-noise mast (available for
2-3 ton models)
Reduced noise from the fork
and carriage significantly
reduces chain shudder.
• Lift Lock
With the engine is off, the forks cannot be lowered, even
when the operator is in the seat.
• Interlock System
This safety device allows traveling and loading/unloading only
when the operator is in the seat.
PORTABLE GLOVE BOX
Detachable and portable.
CUP HOLDER
Convenient for keeping cups, pens
and other small items.
6. OTHER OPTIONAL EQUIPMENT
Rotating warning light Rear working light Overhead exhaust system
Windshield wiper Cabin-panel type
(available for 2-3.5 ton models)
Heater
LPG exclusive/Dual fuel
(LPG/gasoline) package
Pre-cleaner engine air intake Steel cabin-enclosed type with air-cooler
(available for 2-3.5 ton models)
Head light guard Air Boss tire
* As far as the detailed optional
information is concerned, please refer to
the specification sheets.
For various types of attachments, please
also refer to the “attachment catalogue”
which is separately prepared from this
sales catalogue.
7. 1,5 ton
FG15C13 FD15C13 FHD15C3
FG15T13 FD15T13 FHD15T3
FHG15C3 FHD15C3Z
FHG15T3 FHD15T3Z
1,8 ton
FG18C13 FD18C13 FHD18C3
FG18T13 FD18T13 FHD18T3
FHG18C3 FHD18C3Z
FHG18T3 FHD18T3Z
2,0 ton
FG20C3 FD20C3 FHD20C3
FG20T3 FD20T3 FHD20T3
FHG20C3 FD20C3Z
FHG20T3 FD20T3Z
2,5 ton
FG25C3 FD25C3 FHD25C3
FG25T3 FD25T3 FHD25T3
FHG25C3 FD25C3Z
FHG25T3 FD25T3Z
3,0 ton
FG30C3 FD30C3 FHD30C3
FG30T3 FD30T3 FHD30T3
FHG30C3 FD30C3Z
FHG30T3 FD30T3Z
3,5 ton
FD35T3S
TCM has been engaged in manufacturing various forklift truck
models that take into account the needs and requirements of our
valued cutomers. Now, TCM proudly presents the ‘iNOMA series’
with such benefits as enhanced operator comfort, superior safety
assurance, ruggedness and increased durability as well as easy
maintenance and envirnment friendliness. These notable benefits are
backed by TCM’s many years of experience and superb technological
innovations, and TCM is confident in placing the full ‘iNOMA series’
product line on variaus job sites in markets around the world.
23. STANDARD SPECIFICATIONS Gasoline -- 1,5 - 1,8 ton
*Computed values
I Manufacturer TCM
2 Model FG15C13 FG15T13 FG18C13 FG18T13
3 Load Capacity kg 1500 1750
4 Load Center mm 500
5 Power Type Gasoline
6 Operation Position Seated
7 Tire Type Front / Rear Pneumatic
8 Wheels (X=driven) Front / Rear 2X / 2
9 Maximum Fork Height mm 3000
10 Free Lift mm 155
13 Fork Size L x W x T mm 920 x 100 x 35
Fork Spread (Outside) Max. / Min. mm 920 / 200
14 Tilt Angle Fwd / Bwd deg 6 - 12
15 Length to Fork Face mm 2245 2275
16 Overall Width mm 1070 1100
17 Mast Height Fork Lowered mm 1995
18 Mast Height Fork Raised mm 4030
19 Overhead Guard Height (EXB, EXK) mm 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130
20 Operator’s Seat Height mm 1015
21 Turning Radius (Outside) mm 1980 2010
22 Load Distance mm 395
(Centerline of front axle to front face of forks)
Rear Overhang mm 425 455
23 Basic Right Angle Stacking Aisle Width mm 3685 3715
(Add load length and clearance)
24 Speeds Travel Max. Full load km/h 14.0 / 14.0
(Fwd/Rvs.) No load km/h 14.5 / 14.5
25 Lifting Full load mm/s 590
No load mm/s 670
26 Lowering Full load mm/s 450
No load mm/s 550
28 Max. Drawbar Pull Full load kN 9.3 14.5 9.3 14.5
No load kN 6.9
30 Max. Gradeability* Full load % 24 29 20 24
No load % 18
32 Total Weight kg 2510 2670
33 Weight Distribution Full load Front kg 3510 3880
Rear kg 500 540
34 No load Front kg 1070 1030
Rear kg 1440 1640
35 Tires Number Front / Rear 2 / 2
36 Size Front 6.50 - 10 10PR
37 Rear 5.00 - 8 - 8PR
38 Wheelbase mm 1425
39 Tread Front mm 890 920
Rear mm 920
Backrest Height mm 1045
Overhead Guard Clearance mm 1035
Counterweight Height mm 1110
Drawbar Pin Center Height mm 495
Step Height / Floor Height mm 420 / 650
40 Underclearance Min. with load mm 100
41 Center of Wheelbase mm 110
42 Brake Service (Foot) Hydraulic - Foot pedal
43 Parking Mechanical - Hand lever
45 Battery Voltage / Capacity (5HR) V/AH 12 / 28
49 Internal Combustion Engine Make/Model NISSAN K15
Rated Horsepower / r.p.m. kW 25.0 / 2250
Rated Torque / r.p.m. N•m 110.2 / 1600
51 Number of Cylinder 4
52 Piston Displacement cc 1486
Alternator output kW/Amp 0.60 / 50
Fuel Tank Capacity Type lit 50
55 Transmission Type Manual Power-shift Manual Power-shift
Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1
57 Operating Pressure For Attachments MPa (psi) 17.7
Characteristics
Dimensions
Performance
Weight
Chassis
Engine
and
Transmission
24. *Computed values
I Manufacturer TCM
2 Model FHG15C3 FHG15T3 FHG18C3 FHG18T3
3 Load Capacity kg 1500 1750
4 Load Center mm 500
5 Power Type Gasoline
6 Operation Position Seated
7 Tire Type Front / Rear Pneumatic
8 Wheels (X=driven) Front / Rear 2X / 2
9 Maximum Fork Height mm 3000
10 Free Lift mm 155
13 Fork Size L x W x T mm 920 x 100 x 35
Fork Spread (Outside) Max. / Min. mm 920 / 200
14 Tilt Angle Fwd / Bwd deg 6 - 12
15 Length to Fork Face mm 2245 2275
16 Overall Width mm 1070 1100
17 Mast Height Fork Lowered mm 1995
18 Mast Height Fork Raised mm 4030
19 Overhead Guard Height (EXB, EXK) mm 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130
20 Operator’s Seat Height mm 1045
21 Turning Radius (Outside) mm 1980 2010
22 Load Distance mm 395
(Centerline of front axle to front face of forks)
Rear Overhang mm 425 455
23 Basic Right Angle Stacking Aisle Width mm 3685 3715
(Add load length and clearance)
24 Speeds Travel Max. Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0
(Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5
25 Lifting Full load mm/s 600
No load mm/s 680
26 Lowering Full load mm/s 450
No load mm/s 550
28 Max. Drawbar Pull Full load kN 12.7 15.7 12.7 15.7
No load kN 6.9
30 Max. Gradeability* Full load % 25 33 22 31
No load % 18
32 Total Weight kg 2510 2670
33 Weight Distribution Full load Front kg 3510 3880
Rear kg 500 540
34 No load Front kg 1070 1030
Rear kg 1440 1640
35 Tires Number Front / Rear 2 / 2
36 Size Front 6.50 - 10 10PR
37 Rear 5.00 - 8 - 8PR
38 Wheelbase mm 1425
39 Tread Front mm 890 920
Rear mm 920
Backrest Height mm 1045
Overhead Guard Clearance mm 1005
Counterweight Height mm 1110
Drawbar Pin Center Height mm 495
Step Height / Floor Height mm 420 / 650
40 Underclearance Min. with load mm 100
41 Center of Wheelbase mm 110
42 Brake Service (Foot) Hydraulic - Foot pedal
43 Parking Mechanical - Hand lever
45 Battery Voltage / Capacity (5HR) V/AH 12 / 28
49 Internal Combustion Engine Make/Model NISSAN K21
Rated Horsepower / r.p.m. kW 34.6 / 2250
Rated Torque / r.p.m. N•m 153.5 / 1600
51 Number of Cylinder 4
52 Piston Displacement cc 2065
Alternator output kW/Amp 0.60 / 50
Fuel Tank Capacity Type lit 50
55 Transmission Type Manual Power-shift Manual Power-shift
Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1
57 Operating Pressure For Attachments MPa (psi) 17.7
Characteristics
Dimensions
Performance
Weight
Chassis
Engine
and
Transmission
25. STANDARD SPECIFICATIONS Gasoline – 2 - 2.5 - 3 ton
*Computed values
Characteristics
1 Manufacturer TCM
2 Model FG20C3 FG20T3 FG25C3 FG25T3 FG30C3 FG30T3
3
Load Capacity kg 2000 2500 3000
Load Center mm 500 500 500
5 Power type Gasoline Gasoline Gasoline
6 Operator Position Seated Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic
8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2
Dimensions
9 Maximum Fork Height mm 3000 3000 3000
10 Free Lift mm 105 110 165
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45
Fork Spread (Outside) Max. / Min. mm 1020 / 244 1020 / 244 1090 / 250
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555 2705
16 Overall Width mm 1150 1150 1225
17 Mast Height Fork Lowered mm 2030 2030 2075
18 Mast Height Fork Raised mm 4030 4030 4260
19 Overhead Guard Height (EXB, EXK) mm 2070 2070 2090
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130 2150
20 Operator’s Seat Height mm 1045 1045 1070
21 Turning Radius (Outside) mm 2170 2240 2400
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450 480
Rear Overhang mm 435 505 525
23 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185
Performance
24
Speeds
Travel Max. (Fwd. / Rvs.)
Full Load km/h 18,5 18,5 19
No Load km/h 19 19 19,5
25 Lifting
Full Load mm/s 540 540 440
No Load mm/s 580 580 490
26 Lowering
Full Load mm/s 450 450 450
No Load mm/s 550 550 450
28 Max. Drawbar Pull
Full Load kN 12,3 16,7 12,3 16,7 10,8 14,2
No Load kN 8,3 8,3 9,8
29 Max. Gradeability*
Full Load % 20 28 19 24 14 18
No Load % 20 20 20
Weight
32 Total Weight kg 3210 3570 4205
33
Weight Distribution
Full Load
Front kg 4610 5350 6350
Rear kg 600 720 900
34 No Load
Front kg 1430 1370 1620
Rear kg 1780 2200 2630
Chassis
&
Wheels
35
Tires
Number Front / Rear 2 / 2 2 / 2 2 / 2
36
Size
Front 7,00 - 12 - 12PR (l) 7,00 - 12 - 12PR (l) 28 x 9 - 15 - 12PR (l)
37 Rear 6,00 - 9 - 10PR (l) 6,00 - 9 - 10PR (l) 6,50 - 10 - 10PR (l)
38 Wheelbase mm 1600 1600 1700
39 Tread
Front mm 970 970 1000
Rear mm 970 970 970
Backrest Height mm 1040 1040 1300
Overhead Guard Clearance mm 1005 1005 1005
Counterweight Height mm 1110 1110 1130
Drawbar Pin Center Height mm 530 530 560
Step Height / Floor Height mm 435 / 650 435 / 650 460 / 680
40
Underclearance
Minimum Full Load mm 110 110 140
41 Center of wheelbase mm 120 120 145
42
Brake
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal
43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Engine
&
Transmission
45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 30
49
Internal Combustion Engine
Make - Model NISSAN / K21 NISSAN / K21 NISSAN / K21
50 Rated Horsepower / r.p.m. kW 34,6 / 2250 34,6 / 2250 34,6 / 2250
51 Rated Torque / r.p.m. N-m 153,5 / 1600 153,5 / 1600 153,5 / 1600
52
Number of Cylinder 4 4 4
Piston Displacement cc 2065 2065 2065
Alternator output kW/amp 0,60 / 50 0,60 / 50 0,60 / 50
Fuel Tank Capacity Type liter 70 70 70
55 Transmission
Type Manual Power-shift Manual Power-shift Manual Power-shift
Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1
57 Operating Pressure For attachment MPa 17,7 17,7 17,7
26. *Computed values
Characteristics
1 Manufacturer TCM
2 Model FHG20C3 FHG20T3 FHG25C3 FHG25T3 FHG30C3 FHG30T3
3
Load Capacity kg 2000 2500 3000
Load Center mm 500 500 500
5 Power type Gasoline Gasoline Gasoline
6 Operator Position Seated Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic
8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2
Dimensions
9 Maximum Fork Height mm 3000 3000 3000
10 Free Lift mm 105 110 165
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45
Fork Spread (Outside) Max. / Min. mm 1020 / 244 1020 / 244 1090 / 250
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555 2705
16 Overall Width mm 1150 1150 1225
17 Mast Height Fork Lowered mm 2030 2030 2075
18 Mast Height Fork Raised mm 4030 4030 4260
19 Overhead Guard Height (EXB, EXK) mm 2070 2070 2090
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130 2150
20 Operator’s Seat Height mm 1045 1045 1070
21 Turning Radius (Outside) mm 2170 2240 2400
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450 480
Rear Overhang mm 435 505 525
23 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185
Performance
24
Speeds
Travel Max. (Fwd. / Rvs.)
Full Load km/h 18,5 18,5 19
No Load km/h 19 19 19,5
25 Lifting
Full Load mm/s 600 600 500
No Load mm/s 620 620 520
26 Lowering
Full Load mm/s 450 450 450
No Load mm/s 550 550 450
28 Max. Drawbar Pull
Full Load kN 14,2 22,1 14,2 22,1 12,7 19,6
No Load kN 8,3 8,3 9,8
29 Max. Gradeability*
Full Load % 24 36 21 33 18 24
No Load % 20 18 20
Weight
32 Total Weight kg 3220 3580 4260
33
Weight Distribution
Full Load
Front kg 4620 5350 6350
Rear kg 600 730 910
34 No Load
Front kg 1440 1370 1620
Rear kg 1780 2210 2640
Chassis
&
Wheels
35
Tires
Number Front / Rear 2 / 2 2 / 2 2 / 2
36
Size
Front 7,00 - 12 - 12PR (l) 7,00 - 12 - 12PR (l) 28 x 9 - 15 - 12PR (l)
37 Rear 6,00 - 9 - 10PR (l) 6,00 - 9 - 10PR (l) 6,50 - 10 - 10PR (l)
38 Wheelbase mm 1600 1600 1700
39 Tread
Front mm 970 970 1000
Rear mm 970 970 970
Backrest Height mm 1040 1040 1300
Overhead Guard Clearance mm 1005 1005 1005
Counterweight Height mm 1110 1110 1130
Drawbar Pin Center Height mm 530 530 560
Step Height / Floor Height mm 435 / 650 435 / 650 460 / 680
40
Underclearance
Minimum Full Load mm 110 110 140
41 Center of wheelbase mm 120 120 145
42
Brake
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal
43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Engine
&
Transmission
45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 30
49
Internal Combustion Engine
Make - Model NISSAN / K25 NISSAN / K25 NISSAN / K25
50 Rated Horsepower / r.p.m. kW 39,5 / 2100 39,5 / 2100 39,5 / 2100
51 Rated Torque / r.p.m. N-m 188,1 / 1600 188,1 / 1600 188,1 / 1600
52
Number of Cylinder 4 4 4
Piston Displacement cc 2488 2488 2488
Alternator output kW/amp 0,60 / 50 0,60 / 50 0,60 / 50
Fuel Tank Capacity Type liter 70 70 70
55 Transmission
Type Manual Power-shift Manual Power-shift Manual Power-shift
Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1
57 Operating Pressure For attachment MPa 17,7 17,7 17,7
27. STANDARD SPECIFICATIONS Diesel -- 1.5 - 1.8 ton
*Computed values
I Manufacturer TCM
2 Model FD15C13 FD15T13 FD18C13 FD18T13
3 Load Capacity kg 1500 1750
4 Load Center mm 500
5 Power Type Diesel
6 Operation Position Seated
7 Tire Type Front / Rear Pneumatic
8 Wheels (X=driven) Front / Rear 2X / 2
9 Maximum Fork Height mm 3000
10 Free Lift mm 155
13 Fork Size L x W x T mm 920 x 100 x 35
Fork Spread (Outside) Max. / Min. mm 920 / 200
14 Tilt Angle Fwd / Bwd deg 6 - 12
15 Length to Fork Face mm 2245 2275
16 Overall Width mm 1070 1100
17 Mast Height Fork Lowered mm 1995
18 Mast Height Fork Raised mm 4030
19 Overhead Guard Height (EXB, EXK) mm 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130
20 Operator’s Seat Height mm 1015
21 Turning Radius (Outside) mm 1980 2010
22 Load Distance mm 395
(Centerline of front axle to front face of forks)
Rear Overhang mm 425 455
23 Basic Right Angle Stacking Aisle Width mm 3685 3715
(Add load length and clearance)
24 Speeds Travel Max. Full load km/h 13.5 / 13.5
(Fwd/Rvs.) No load km/h 14.0 / 14.0
25 Lifting Full load mm/s 530
No load mm/s 600
26 Lowering Full load mm/s 450
No load mm/s 550
28 Max. Drawbar Pull Full load kN 8.8 13.7 8.8 13.7
No load kN 6.9
30 Max. Gradeability* Full load % 22 24 20 21
No load % 19 16
32 Total Weight kg 2540 2700
33 Weight Distribution Full load Front kg 3530 3900
Rear kg 510 550
34 No load Front kg 1090 1050
Rear kg 1450 1650
35 Tires Number Front / Rear 2 / 2
36 Size Front 6.50 - 10 10PR
37 Rear 5.00 - 8 - 8PR
38 Wheelbase mm 1425
39 Tread Front mm 890 920
Rear mm 920
Backrest Height mm 1045
Overhead Guard Clearance mm 1035
Counterweight Height mm 1110
Drawbar Pin Center Height mm 495
Step Height / Floor Height mm 420 / 650
40 Underclearance Min. with load mm 100
41 Center of Wheelbase mm 110
42 Brake Service (Foot) Hydraulic - Foot pedal
43 Parking Mechanical - Hand lever
45 Battery Voltage / Capacity (5HR) V/AH 12 / 52
49 Internal Combustion Engine Make/Model KUBOTA D1503
Rated Horsepower / r.p.m. kW 21.3 / 2500
Rated Torque / r.p.m. N•m 98 / 1600
51 Number of Cylinder 3
52 Piston Displacement cc 1499
Alternator output kW/Amp 0.54 / 45
Fuel Tank Capacity Type lit 50
55 Transmission Type Manual Power-shift Manual Power-shift
Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1
57 Operating Pressure For Attachments MPa (psi) 17.7
Characteristics
Dimensions
Performance
Weight
Chassis
Engine
and
Transmission
28. *Computed values
I Manufacturer TCM
2 Model FHG15C3 FHG15T3 FHG18C3 FHG18T3
3 Load Capacity kg 1500 1750
4 Load Center mm 500
5 Power Type Diesel
6 Operation Position Seated
7 Tire Type Front / Rear Pneumatic
8 Wheels (X=driven) Front / Rear 2X / 2
9 Maximum Fork Height mm 3000
10 Free Lift mm 155
13 Fork Size L x W x T mm 920 x 100 x 35
Fork Spread (Outside) Max. / Min. mm 920 / 200
14 Tilt Angle Fwd / Bwd deg 6 - 12
15 Length to Fork Face mm 2245 2275
16 Overall Width mm 1070 1100
17 Mast Height Fork Lowered mm 1995
18 Mast Height Fork Raised mm 4030
19 Overhead Guard Height (EXB, EXK) mm 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130
20 Operator’s Seat Height mm 1045
21 Turning Radius (Outside) mm 1980 2010
22 Load Distance mm 395
(Centerline of front axle to front face of forks)
Rear Overhang mm 425 455
23 Basic Right Angle Stacking Aisle Width mm 3685 3715
(Add load length and clearance)
24 Speeds Travel Max. Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0
(Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5
25 Lifting Full load mm/s 620
No load mm/s 680
26 Lowering Full load mm/s 450
No load mm/s 550
28 Max. Drawbar Pull Full load kN 14.7 18.6 14.7 18.6
No load kN 6.9
30 Max. Gradeability* Full load % 25 33 22 31
No load % 18 17
32 Total Weight kg 2620 2780
33 Weight Distribution Full load Front kg 3550 3910
Rear kg 570 620
34 No load Front kg 1110 1060
Rear kg 1510 1720
35 Tires Number Front / Rear 2 / 2
36 Size Front 6.50 - 10 10PR
37 Rear 5.00 - 8 - 8PR
38 Wheelbase mm 1425
39 Tread Front mm 890 920
Rear mm 920
Backrest Height mm 1045
Overhead Guard Clearance mm 1005
Counterweight Height mm 1110
Drawbar Pin Center Height mm 495
Step Height / Floor Height mm 420 / 650
40 Underclearance Min. with load mm 100
41 Center of Wheelbase mm 110
42 Brake Service (Foot) Hydraulic - Foot pedal
43 Parking Mechanical - Hand lever
45 Battery Voltage / Capacity (5HR) V/AH 12 / 64
49 Internal Combustion Engine Make/Model NISSAN DIESEL TD27 - II
Rated Horsepower / r.p.m. kW 42.0 / 2400
Rated Torque / r.p.m. N•m 170 / 2300
51 Number of Cylinder 4
52 Piston Displacement cc 2663
Alternator output kW/Amp 0.72 / 60
Fuel Tank Capacity Type lit 50
55 Transmission Type Manual Power-shift Manual Power-shift
Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1
57 Operating Pressure For Attachments MPa (psi) 17.7
Characteristics
Dimensions
Performance
Weight
Chassis
Engine
and
Transmission
29. STANDARD SPECIFICATIONS Diesel -- 2 - 2,5 - 3 - 3,5 ton
Characteristics
1 Manufacturer TCM
2 Model FD20C3 FD20T3 FD25C3 FD25T3
3
Load Capacity kg 2000 2500
Load Center mm 500 500
5 Power type Diesel Diesel
6 Operator Position Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic
8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2
Dimensions
9 Maximum Fork Height mm 3000 3000
10 Free Lift mm 105 110
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40
Fork Spread (Outside) Max. / Min. mm 1020 / 245 1020 / 245
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555
16 Overall Width mm 1150 1150
17 Mast Height Fork Lowered mm 2030 2030
18 Mast Height Fork Raised mm 4030 4030
19 Overhead Guard Height (EXB, EXK) mm 2070 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130
20 Operator’s Seat Height mm 1045 1045
21 Turning Radius (Outside) mm 2170 2240
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450
Rear Overhang mm 435 505
23 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995
Performance
24
Speeds
Travel Max. (Fwd. / Rvs.)
Full Load km/h 18,5 18 18,5 18
No Load km/h 19 18,5 19 18,5
25 Lifting
Full Load mm/s 630 630
No Load mm/s 670 670
26 Lowering
Full Load mm/s 450 450
No Load mm/s 550 550
28 Max. Drawbar Pull
Full Load kN 13,7 19,1 13,7 19,1
No Load kN 8,3 8,3
29 Max. Gradeability*
Full Load % 23 34 20 28
No Load % 20 20
Weight
32 Total Weight kg 3340 3700
33
Weight Distribution
Full Load
Front kg 4670 5400
Rear kg 670 800
34 No Load
Front kg 1490 1420
Rear kg 1850 2280
Chassis
&
Wheels
35
Tires
Number Front / Rear 2 / 2 2 / 2
36
Size
Front 7,00 - 12 - 12PR (l) 7,00 - 12 - 12PR (l)
37 Rear 6,00 - 9 - 10PR (l) 6,00 - 9 - 10PR (l)
38 Wheelbase mm 1600 1600
39 Tread
Front mm 970 970
Rear mm 970 970
Backrest Height mm 1040 1040
Overhead Guard Clearance mm 1005 1005
Counterweight Height mm 1110 1110
Drawbar Pin Center Height mm 530 530
Step Height / Floor Height mm 435 / 650 435 / 650
40
Underclearance
Minimum Full Load mm 110 110
41 Center of wheelbase mm 120 120
42
Brake
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal
43 Parking Mechanical-Hand lever Mechanical-Hand lever
Engine
&
Transmission
45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64
49
Internal Combustion Engine
Make - Model NISSAN DIESEL / TD27-II NISSAN DIESEL / TD27-II
50 Rated Horsepower / r.p.m. kW 42,0 / 2400 42,0 / 2400
51 Rated Torque / r.p.m. N-m 170 / 2300 170 / 2300
52
Number of Cylinder 4 4
Piston Displacement cc 2663 2663
Alternator output kW/amp 0,72 / 60 0,72 / 60
Fuel Tank Capacity Type liter 70 70
55 Transmission
Type Manual Power-shift Manual Power-shift
Stage Fwd - Rvs 2-2 1-1 2-2 1-1
57 Operating Pressure For attachment MPa 17,7 17,7
30. Characteristics
1 Manufacturer TCM
2 Model FD30C3 FD30T3 FD35T3S
3
Load Capacity kg 3000 3500
Load Center mm 500 500
5 Power type Diesel Diesel
6 Operator Position Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic
8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2
Dimensions
9 Maximum Fork Height mm 3000 3000
10 Free Lift mm 165 170
13 Fork Size L x W x T mm 1070 x 122 x 45 1070 x 150 x 50
Fork Spread (Outside) Max. / Min. mm 1090 / 250 1090 / 300
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12
15 Lenght to Fork Face mm 2705 2800
16 Overall Width mm 1225 1290
17 Mast Height Fork Lowered mm 2075 2135
18 Mast Height Fork Raised mm 4260 4255
19 Overhead Guard Height (EXB, EXK) mm 2090 2140
Overhead Guard Height (EXC, EXE, EXN) mm 2150 2200
20 Operator’s Seat Height mm 1070 1120
21 Turning Radius (Outside) mm 2400 2470
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 480 495
Rear Overhang mm 525 605
23 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 4185 4145
Performance
24
Speeds
Travel Max. (Fwd. / Rvs.)
Full Load km/h 19 19
No Load km/h 19,5 19,5
25 Lifting
Full Load mm/s 520 460
No Load mm/s 590 490
26 Lowering
Full Load mm/s 450 420
No Load mm/s 450 450
28 Max. Drawbar Pull
Full Load kN 12,7 17,2 18,1
No Load kN 9,8 10,8
29 Max. Gradeability*
Full Load % 15 21 20
No Load % 20 17
Weight
32 Total Weight kg 4390 4940
33
Weight Distribution
Full Load
Front kg 6410 7290
Rear kg 980 800
34 No Load
Front kg 1680 1420
Rear kg 2710 2280
Chassis
&
Wheels
35
Tires
Number Front / Rear 2 / 2 2 / 2
36
Size
Front 28 x 9 - 15 - 12PR (l) 7,00 - 12 - 12PR (l)
37 Rear 6,50 - 10 - 10PR (l) 6,00 - 9 - 10PR (l)
38 Wheelbase mm 1700 1600
39 Tread
Front mm 1000 970
Rear mm 970 970
Backrest Height mm 1300 1040
Overhead Guard Clearance mm 1005 1005
Counterweight Height mm 1130 1110
Drawbar Pin Center Height mm 560 530
Step Height / Floor Height mm 460 / 680 435 / 650
40
Underclearance
Minimum Full Load mm 140 110
41 Center of wheelbase mm 145 120
42
Brake
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal
43 Parking Mechanical-Hand lever Mechanical-Hand lever
Engine
&
Transmission
45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64
49
Internal Combustion Engine
Make - Model NISSAN DIESEL / TD27-II NISSAN DIESEL / TD27-II
50 Rated Horsepower / r.p.m. kW 42,0 / 2400 42,0 / 2400
51 Rated Torque / r.p.m. N-m 170 / 2300 170 / 2300
52
Number of Cylinder 4 4
Piston Displacement cc 2663 2663
Alternator output kW/amp 0,72 / 60 0,72 / 60
Fuel Tank Capacity Type liter 70 70
55 Transmission
Type Manual Power-shift Manual
Stage Fwd - Rvs 2-2 1-1 2-2
57 Operating Pressure For attachment MPa 17,7 17,7
31. Characteristics
1 Manufacturer TCM
2 Model FHD20C3 FHD20T3 FHD25C3 FHD25T3 FHD30C3 FHD30T3
3
Load Capacity kg 2000 2500 3000
Load Center mm 500 500 500
5 Power type Diesel Diesel Diesel
6 Operator Position Seated Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic
8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2
Dimensions
9 Maximum Fork Height mm 3000 3000 3000
10 Free Lift mm 105 110 165
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45
Fork Spread (Outside) Max. / Min. mm 1020 / 245 1020 / 245 1090 / 250
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555 2705
16 Overall Width mm 1150 1150 1225
17 Mast Height Fork Lowered mm 2030 2030 2075
18 Mast Height Fork Raised mm 4030 4030 4260
19 Overhead Guard Height (EXB, EXK) mm 2070 2070 2090
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130 2150
20 Operator’s Seat Height mm 1045 1045 1070
21 Turning Radius (Outside) mm 2170 2240 2400
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450 480
Rear Overhang mm 435 505 525
23 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185
Performance
24
Speeds
Travel Max. (Fwd. / Rvs.)
Full Load km/h 18 18 19
No Load km/h 18,5 18,5 19,5
25 Lifting
Full Load mm/s 620 620 520
No Load mm/s 640 640 540
26 Lowering
Full Load mm/s 450 450 450
No Load mm/s 550 550 450
28 Max. Drawbar Pull
Full Load kN 15,7 26,5 15,7 26,5 14,8 13,5
No Load kN 8,3 8,3 9,8
29 Max. Gradeability*
Full Load % 28 38 24 32 16 27
No Load % 20 18 20
Weight
32 Total Weight kg 3340 3700 4390
33
Weight Distribution
Full Load
Front kg 4680 5400 6410
Rear kg 660 800 980
34 No Load
Front kg 1500 1420 1690
Rear kg 1840 2280 2700
Chassis
&
Wheels
35
Tires
Number Front / Rear 2 / 2 2 / 2 2 / 2
36
Size
Front 7,00 - 12 - 12PR (l) 7,00 - 12 - 12PR (l) 28 x 9 - 15 - 12PR (l)
37 Rear 6,00 - 9 - 10PR (l) 6,00 - 9 - 10PR (l) 6,50 - 10 - 10PR (l)
38 Wheelbase mm 1600 1600 1700
39 Tread
Front mm 970 970 1000
Rear mm 970 970 970
Backrest Height mm 1040 1040 1300
Overhead Guard Clearance mm 1005 1005 1005
Counterweight Height mm 1110 1110 1130
Drawbar Pin Center Height mm 530 530 560
Step Height / Floor Height mm 435 / 650 435 / 650 460 / 680
40
Underclearance
Minimum Full Load mm 110 110 140
41 Center of wheelbase mm 120 120 145
42
Brake
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal
43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Engine
&
Transmission
45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64 12 / 64
49
Internal Combustion Engine
Make - Model KUBOTA /V3300 KUBOTA /V3300 KUBOTA /V3300
50 Rated Horsepower / r.p.m. kW 50 / 2500 50 / 2500 50 / 2500
51 Rated Torque / r.p.m. N-m 226,4 / 1800 226,4 / 1800 226,4 / 1800
52
Number of Cylinder 4 4 4
Piston Displacement cc 3318 3318 3318
Alternator output kW/amp 0,54 / 45 0,54 / 45 0,54 / 45
Fuel Tank Capacity Type liter 70 70 70
55 Transmission
Type Manual Power-shift Manual Power-shift Manual Power-shift
Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1
57 Operating Pressure For attachment MPa 17,7 17,7 17,7