Fabrication of electro mechanical controlled bike stand
•Download as PPTX, PDF•
0 likes•27 views
This document describes a project to design an electro-mechanical controlled bike stand. The stand is intended to make it easier for senior citizens and women to deploy a center stand on their bikes. It uses a rack and pinion mechanism connected to a DC motor that can be controlled with switches to raise and lower the center stand. The objectives are to avoid effort in deploying the center stand, prevent accidents from improper side stand use, and reduce parking space needs compared to a side stand. Components include the motor, rack and pinion assembly, frame, switches, and battery. The design is intended to provide easier center stand use, increase safety, and allow more efficient parking.
Recommended
More Related Content
What's hot
What's hot (20)
Similar to Fabrication of electro mechanical controlled bike stand
Similar to Fabrication of electro mechanical controlled bike stand (20)
Recently uploaded
Recently uploaded (20)
Fabrication of electro mechanical controlled bike stand
- 1. • Pudi Pratap Kumar (11504432) • Sk Feroz Basha (11505081) • U Ganesh Kumar (11504016) • J Dinesh Reddy (11505434) • A Shanmukha Reddy (11504170) UNDER GUIDANCE OF Mandeep Singh (Assistant professor) FABRICATION OF ELECTRO-MECHANICAL CONTROLLED BIKE STAND
- 2. INTRODUCTION • Now a day’s placing a center stand while parking on the uneven road is difficult and risky, to overcome his problem we are using some mechanical solutions. Our project is mainly focuses on the problems faced by the senior citizens and women who are using two wheelers. Most of the times in the scooters the engine is placed at the rear part, so it is difficult for the women and senior citizens to apply center stand • Out of the 100 bike accidents, 12 of the bike accidents are occur due to the negligence of leaving side stand. Keeping the people safety in the mind , the project is designed more economical and affordable to use
- 3. • One of the advantage of using center stand over side stand is space. Parking areas in some public places are very crowded (especially in cities). Using the side stand means your bike is at an angle () to the road. So it takes up slightly more space than if it was on its center stand (|). • Looking at one bike alone, it doesn't look like we save a lot of space. But if you consider 20 - 30 bikes parked in a row it probably means you can cram in a few more bikes. INTRODUCTION
- 4. STATISTICS Reason For The Accident %Of Accidents • 2012-2015 Forgetting to lift side-stand 36% • 2012-2015 Does not maintain speed limit 38% • 2012-2015 Does not obey traffic rules 22% • 2012-2015 Other problems 04%
- 5. PROBLEM STATEMENT • On surveying, it was found that around 70% males and 30% females drive motorcycle • Among those 70% males, around 30% are oldies and remaining are adults • Most of the females and old people observe that it is very difficult to apply centre stand and hence this made us develop and make it automated. • Moreover, applying a side stand,More parking area is consumed if we use side stand instead of center stand • May cause back and/or leg injuries mainly for older people Because of people forget to take the side stand-off while riding, accidents may happen
- 6. OBJECTIVE • . To avoid lot of effort by a person to apply centre stand. • To avoid accidents caused by improper use of side stand. • To reduce the space required for the bike in parking by using centre stand instead of side stand.
- 7. COMPONENTS USED: 1. Motor 2. Rack and Pinion Assembly 3. Frame 4. Electrical Switches 5. Battery
- 8. WORKING: 1. We are using rack & pinion mechanism in which pinion is connected to Dc motor which can be controlled manually with the help of switches. 2. Rack is connected to the centre stand and side stand with the help of nut and bolt adjustment. when the bike is at rest and to apply centre stand need to activate anti-clockwise direction switch likewise for return need to activate clock- wise stwitch . 3. To activate side stand we need to connect it with nut and bolt to the rack and pinion joint. Note: All of this components are arranged on the rectangular metal frame .
- 9. BLOCK DIAGRAM Battery Switch DC Motor Rack and Pinion stand
- 10. COMPONENTS DESIGNED Stand Frame Pin Link plate
- 12. ADVANTAGES • System able to provide ease of comfort to apply centre stand. • System plays an important role to save human Life in road accidents • Easy installation. • Parking space needed will be less
- 13. Limitations • Occupies more space. • More number of moving parts. • Maintenance cost is high. Applications • This system can be applicable in all types of heavy two wheeler vehicles. • Reduces parking space due to usage of centre stand over side stand • Increases safe usage of bike stand