2. II
Product data and information contained in this catalog have
been derived from information obtained from Avionics Inter-
national Supply, Inc. (AIS) suppliers. Some of this information
has been summarized and rearranged to facilitate search-
ing the catalog. While AIS attempts to verify the accuracy of
this catalog information, AIS does not assume responsibility
for errors or omissions. This catalogs information is subject
to change without notice, and AIS does not undertake any
obligation to provide updates.
The information contained in this catalog is intended for use
by persons possessing appropriate technical skill and knowl-
edge. Conditions of use of the items listed in the catalog are
beyond the knowledge or control of AIS. Consequently, AIS
assumes no liability whatsoever for results obtained or loss or
damage incurred as a result of the application of the informa-
tion presented. All users of this catalog do so at their own risk.
The catalog is neither a parts nor maintenance manual ap-
proved by the Federal Aviation Administration (FAA), and it
is not intended to replace the manuals provided by the AIS
suppliers. Users should independently verify the suitability
and legality of each product for its intended purpose before
the product is installed on an aircraft by means of an appro-
priate parts or maintenance manual, or other approved FAA
documentation.
AIS assumes no liability and makes no warranty with respect
to claims of patent, trademark or copyright infringement
or other similar claims which may arise out of or in connec-
tion with the use of any information or product listed in the
catalog.
AIS expressly disclaims all warranties, expressed or implied,
including but not limited to implied warranties of merchant-
ability and fitness for any particular purpose. In no event
shall AIS be liable for any injury, expenses, profits, loss or
damage, direct, indirect, incidental, consequential, special,
punitive or otherwise, arising out of the use or inability to use
any information or product described in this catalog.
Because some jurisdictions do not allow the exclusion or
limitation of liability for consequential or incidental damages,
the limitation in the paragraph immediately above may not
apply to you.
TERMS & CONDITIONS:
Avionics International supply, Inc. is a wholesale distributor
of avionics, installation supplies and support equipment. We
support avionics dealers and completion centers throughout
the world. We only sell to authorized dealers upon an AIS
approval. With this approval, you may purchase with terms
of COD or credit card. An open account of net 30 can be
achieved with verification of credit references and a signed
credit application. This signed application give AIS the right
to charge 1% interest per month on past due balances.
AIS WARRANTY & RETURNED MATERIALS POLICY:
GENERAL PROVISIONS:
Each returned part must have a Return Material Authorization
(RMA) number assigned to it by an AIS Customer Service Rep-
resentative before the return will be processed by Avionics In-
ternational Supply, Inc. (AIS). Returned parts must have been
originally purchased from AIS and must be in their original
packaging and properly packaged to prevent shipping and
handling damage.
AIS will return to the customer either new, repaired or re-
manufactured items or components that are warranted in ac-
cordance with the original Manufacturer’s warranty. Products
sold by AIS are warranted under the original manufacturer,
not AIS. Defective products returned will only be issued
credit upon the original manufacturer authorization and all
credits, if any, will be account credits against future purchases
from AIS.
RMA NUMBERS AND PROCESS:
AIS, at its option, may return, unprocessed, and at the send-
er’s expense, any item received without a valid RMA number.
To obtain the required RMA numbers, the Customer will
contact an AIS Customer Service Representative and provide
the AIS Customer Service Representative with the following
information:
1. Original AIS Sales Order or Invoice Number
2. Customer name or AIS Customer Account Number
3. Contact and call-back telephone number
4. Serial number and/or part number for each item to be
returned
5. Reason item is being returned
[Note: The AIS Customer Service Representative may need additional infor-
mation depending on the nature of the problem.]
Avionics International Supply, Inc. Catalog Disclaimer
3. IIIIII
RMA NUMBERS AND PROCESS (cont’d):
AIS Customer Service will verify the warranty status of each
item before assigning an RMA number. Serial Numbers and
purchase date will be verified against all available AIS and
manufacturer records. Non-warranty items will require a
Customer Purchase Order number to be issued to AIS before
repairs will be started on the RMA.
If a product is returned to AIS it may be subject to a re-stock-
ing fee at AIS’s discretion.
An RMA number will be assigned to each shipment or each
item to be returned.
SHIPPING INFORMATION:
Shipment must contain a packing list with the RMA number,
Part Numbers and Serial Numbers for each item. RMA num-
bers must be clearly marked on the outside of the shipping
containers.
Use original packaging for returns. Poor packaging may
result in physical damage to the returned part(s). If the
shipment is damaged, AIS will document the damage, notify
the sender. All costs associated with repair of the damage
from shipment will be borne by the sender. In some cases,
damage to the shipment may result in the cancellation of the
items within that shipment.
The Customer will pre-pay freight to AIS, and AIS will pre-pay
return freight to the Customer. AIS will use the most eco-
nomical method of shipment. Any special Customer shipping
requests will be billed to the Customer.
NO DEFECT FOUND CHARGE:
The customer will be charged $125 for each item which is
returned for RMA if the item is found to be in sound work-
ing condition and found to be free of defects by the original
manufacturer. The customer will be notified and a purchase
order will be required for the full amount of the charges be-
fore the equipment will be returned.
ADVANCED REPLACEMENT PARTS REQUEST:
In the event a requirement for an Advanced Replacement
Part exists, a Customer Purchase Order must be sent to
the AIS Customer Service representative. Expedite Fee’s
for advance replacements will be the responsibility of the
customer. The customer will be billed for the full price for any
part if like or same item is not returned within 30 days under
the RMA process.
AIS will use its reasonable best efforts to process the Emer-
gency Purchase Order during the same day the order is
received. The Customer will pay all shipping costs.
CUSTOMER SERVICE CONTACT INFORMATION:
Phone: 1-800-553-2233 or 940-566-0035
Fax: 940-566-8656
Email: info@avionicsinternational.com
TERMS OF SALE:
For established Net 30 days accounts: Full payment is due 30
days from invoice date.
MINIMUM CREDIT PURCHASE:
$50.00 Due to the cost of processing charge orders, no dis-
counts will be extended for orders less than $50 list price.
RETURNS:
Please see the Returned Material Authorization (RMA) proce-
dure.
SHIPPING CHARGES:
Unless otherwise directed, all orders are shipped via UPS or
Fedex Ground, FOB our dock, and may take up to five or six
working days to reach regions near the East and West coasts.
Expedited shipping is available, at published rates.
4. IV
ACCESSORIES
Adapter Cables 409
Handheld Radios 409
Mini Power Inverters 408
Portable PTT Switches 409
AC TO AC POWER SUPPLIES
Light Dimmers
FJ20 228
E/L Power Converters
FD15 229
60/50Hz Frequency Converters
HB200 232
HB Series 230
HS200 232
HS Series 230
AC TO DC POWER CONVERTERS
LT-2XX-400 Series 236
PFA1 234
SRP500-14 235
WH120 238
Light Dimmers
LT-25 239
ADDITIONAL ITEMS 423
ADD. MID CONTINENT P/N 364
AERO EXPRESS
Busmaster 2500 330
AERONAUTICAL TEST KITS
& ACCESSORIES 11
AEROSPACE TEST/CAL EQUIP.
Master Site Compass 314
Pitot/Static Test Set 313
SA37-P-UNI-2 313
SA3Y-9-LTS 314
AIRSPEED INDICATOR
LUN 1106 385
LUN 1107 384
LUN 1115 383
LUN 1116 382
LUN 1170 386
ALTIMETERS
LUN 1120 376
LUN 1127 377
LUN 1128 378
LUN 1130 379
AM/FM ANTENNAS
CI 222 119
ANNUNCIATOR CONTROL UNITS
TAWS/EGPWS Annunciators
AK-950-xxx Series 352
MD41-xxxx Series 351
MD41 Series 350
GPS/NAV Annunciators 353
ARTEX ELT TO NAV INTERFACE 214
BRASS & NYLON FITTINGS 6
CABLE MOUNTS & FASTENERS 8
Cable Tie Mounts
Braided Nylon Lacing Cord
Cradle Cable Tie Mounts
Expandable Sleeving
Lightning Hole Cable Tie Mount
Loop Type Fastener ADEL
Clamp
Spiral Wrap
CAPITAL AVIONICS
CA-323 323
CA320 322
CIRCUIT SAFETY LOCKS 10
CLOCKS
AT-1 371
LC-2, LC-2P. LC-2PC 370
LC-20 371
LC-20A 371
LC-2A-5 371
LC-2A-6 371
LC-2E 371
LC-2H 371
LC-2PC 371
LC-6 371
LC-60 371
LC-8 (28v) 371
LC-8 (5v) 370
LC-90 371
LC-C, LC-6PC 370
M800 372
M811B 372
M877 372
w/ Outside Air Temp
M803 372
MD-90 Series 373
MD40 Series 374
COLORED BREAKER COLLARS 10
COMDAT ANTENNAS
COMDAT SERIES FAQ 41
CI 150-250-L 50
CI 248-180 49
CI 248-30 48
CI 248-5 43
CI 2480-100 44
CI 2480-101 45
CI 2480-200 46
CI 2480-201 47
CI 2480-204 51
CI 2480-206 52
CI 2480-300 53
CI 2480-301 54
CI 2480-304 56
CI 2480-400 57
CI 2480-401 58
CI 2580-200 59
CI 2580-410 60
CI 268-10 61
CI 268-30 62
CI 2680-200 65
CI 2680-204 66
CI 2680-206 67
CI 2680-300 68
CI 2680-301 69
CI 2680-304 70
CI 2680-400 71
CI 2680-401 72
CI 2680-500 73
CI 2728-200 74
CI 2728-410 75
CI 2780-464 76
CI 401-220 77
CI 401-220 77
CI 401-221 77
CI 401-224 79
CI 401-230 80
CI 401-421 81
CI 401-460 82
CI 408-20 78
CI 420-10 84
CI 420-16 85
CI 420-1 83
CI 420-220 92
CI 420-221 55
CI 420-224 86
CI 420-230 87
CI 420-420 88
CI 420-421 89
CI 428-200 90
CI 428-410 91
CI 480-1 63
CI 490-1
CONNECTORS ADAPTERS
BNC Adapters 19
BNC Connectors 18
GPS Notch Filter 18
N Type Connectors 19
SMA UHF Connectors 19
TNC Connectors 18
Tray Mount RF Connector 18
CONNECTORS PINS
AC/DC Recepticles 23
ARC Transponder Contacts 21
Block Receptacle 20
Clamps 23
Grounding Blocks 20
HD Positioner 21
HD Sub-D Connectors 21
Insertion/Extraction Tools 23
King Double Edge Pins 21
Male Jack Screws 20
Mate-N-Lok Connectors 21
Metrimate Connectors 20
Narco Contacts 21
“PIDG” Splices 20
“PIDG” Splices 20
“PIDG” Terminals 20
“Round Tongue” Terminals 20
“Solistrand” Ring Terminals 20
“Terminal” Ring Terminals 20
Power Connectors 22
Reverse Sex Connectors 22
CPC Connectors 22
Sockets For Grounding 20
Pins 22
Standard Sex Connectors 22
Subminiature D Connectors 21
Wire Caps 20
COOLING FANS HOSE 30
COPPER BUSS BAR 10
COVER/REDUCER PLATES 3
Dzus Rail
Instrument Cover Plates
Mu-Metal
Reducer Plates
Sqeeze Clamps
COUPLER/DIPLEXER
CI 502 184
CI 503 185
CI 505 186
CI 507 187
CI 509 188
CI 601 189
CI 1114 190
CI 1115 191
CI 1120 192
CI 1125 193
TABLE OF CONTENTS
5. VV
CRIMPERS WIRE STRIPPERS 26
Replacement Die Sets 27
DC TO DC POWER CONVERTERS
Unregulated 240
UC14-28 240
UC28-14 241
Light Dimmers
AK-551LD-( ) 253
AK-551LD-M-( ) 254
LF10 243
LH14 252
LT-100 244
LT-103 246
LT-248 242
LT-3xx Series 250
LT-52(A) 244
LT-53 246
LT-55( ) Series 248
LT-57( ) Series 248
LT-70 244
LT-73 246
Step Up
AK-550-12 255
AK-550-6 255
LS03-05002 261
RB125 256
Step Up (Cont’d)
RB126 256
RH28 260
RHB40 258
Step Down
AK-551-18M 271
AK-551-40M 271
AK-551-9M 271
BC-14 266
BC-28 266
DC TO DC POWER CONV. (CONT’D)
Step Down (Cont’d)
LS03-05001 272
LT-101 Series 264
LT-4x Series 262
LT-50 267
LT-71 Series 264
N2412-12 272
N2412-24 272
RG28 268
RG40 269
RG56 270
Dual Channel
RR18 273
DC TO DC/AC POWER CONVERTERS
Light Dimmers
DT30 274
DC TO AC STATIC INVERTERS
400Hz
MD 26 Series 286
SC-50 281
SC100 284
SC3 275
SCA150 285
SCA3 275
SPC-10( ) Series 277
SPC-10(J) Series 278
SPC-30( ) Series 279
SPC-38( ) Series 280
SPC-5( ) Series 276
SPC-60( ) Series 282
SPC-75( ) Series 283
400Hz E/L
SD3 287
SD35 288
SE25 289
400Hz Three Phase
SEA150 290
60/50Hz
SB200 296
SB Series 294
SPS-1307 Series 292
SPS-1607 Series 292
SPS-2xx Series 291
SPS-3xx Series 291
SPS-750 292
SS200 296
SS50 293
SS50(D) 298
SS Series 294
DME/TRANSPONDER
CI 100 Series 152
CI 101 153
CI 105-16 158
CI 105-3 155
CI 105-6 7 156
CI 105-9 157
DME/TRANSPONDER (CONT’D)
CI 105 Series 154
CI 110-40-30 159
CI 110-41-30 160
CI 110-60-30 161
CI 110-61-30 162
CI 305 Series 163
DMNI24/DMNI29 Series 164
DMNI50 Series 165
DMNI52 Series 166
DMNI70 Series 167
DROP CORDS
AIS Universal Drop Cords 401
CIX 200 Series 402
CIX 300 Series 403
CIX 400 Series 404
Drop Cord Spare Parts 405
DROP CORD WIRING CONFIG 407
EATON
Switches
580/581 Series 341
582 Series 340
584 LED Series 341
584 Series 340
Lamps 343
Master Specialty
10E/10H Twist-Lite
Series 343
800/820 Tellite Series 343
90lE/90lH Tellite Series 343
90lK Tellite Series 343
TAWS/EGPWS
Annunciators 344
EATON Accessories 346
EATON Specifications
Dimensional 347
Electrical 348
Environmental 348
Wiring 347
EATON CONFIG FORM 366
ELECTRIC ATTITUDE GYROS
LUN 1241 380
ELT SELECTION GUIDE 208
ELTS, BUSINESS AVIATION
C406-1 Series 211
C406-2 Series 211
C406-N Series 212
ELTS, COMMERCIAL AVIATION
C406-1 Series 212
C406-2 Series 212
C406-N Series 213
B406 (Boeing) Series 213
ELTS, GENERAL AVIATION
ME406 Series 210
G406 Series 210
C406-N Series 210
ELTS, HELICOPTER
ME406 Series 213
C406-1 Series 213
C406-2 Series 214
C406-N Series 214
ELTS, OTHER
DM ELT 14-1-1 215
AK-450 Series 216
Model E-01 217
3000 Series 218
ELT BATTERIES 214
ELT-NAV INTERFACE KIT
CS144-RS 209
ENCODERS
A-30 222
AK-350 222
SAE5-35 220
SSD120-(xx)A(E) 223
ENVIRONMENTAL SPLICES 12
FOIL 424
FM ANTENNAS
CI 222-1 120
FM/2 METER ANTENNAS
CI 177-13 116
CI 177-1 114
CI 177-3 115
CI 177 113
CI 292-3 117
CI 292-4 118
FUSES 12
GLIDE SLOPE
CI 193 177
CI 212-2 178
DMN9 Series 179
GPS ATTENUATOR
CI 511 194
GPS REPEATER KITS 314
L1 Antennas 314
GPS SPLITTERS 315
GROMMETS 10
GUAGES
Digital VOR Indicator Localizer
903ID-2 375
Morse Code Identifier
903ID-2 375
Density Altitude
665-2 375
Digital Outside Air Temp
301C 375
301F 375
6. VI
HEADSETS
7000 ANR ProGT/ProGTH 397
7000 Sport LE/LEH 397
David Clark X11 Headset 394
H10-00 394
H10-13.4 394
H10-13X 394
H10-13XL 394
H10-13XP 394
H10-20 395
H10-30 395
H10-56 395
H10-56 HXL 395
H10-60 395
H10-66 396
H10-76 396
H20-10 396
H20-10XL 396
H20-10XP 396
HMEC25-CAP 397
HMEC25-KA 397
HMEC25-KAP 397
HMEC25-KAS 397
HME C25-KAX 397
HMEC300 397
Junior Series P-51C 398
PA 11-20 398
PA 11-40 398
PA 11-60 “The Eliminator” 398
PA 11-90 399
PA 31-70 398
P-51 399
Powercom 2-way Wireless 397
Headset Accessories
Booms 399
David Clark Accessories 396
Microphones 399
Microphone Windscreens 399
Peltor Headset Accessories 397
HEAT GUNS 32
Heat Gun Accessories 36
HEAT SHRINK TUBING 9
HEX STANDOFFS 10
HOT STAMP MARKERS
SEI-50 416
SEI-150 417
SEI-250 418
SEI-450 419
Upgrade Kits 420
JACK HOUSINGS 3
LABEL MAKERS
K-Sun 29
KROY 28
LASER WIRE MARKERS
CAPRIS 50-100 PCS 413
Laser System 1 - IR 414
Laser System 1 - UV 415
LASER WIRE MARKING 412
LAVERSAB TEST EQUIP
6300 324
6500 325
LINAIRE ENGINEERING
JT-2 327
L-280 326
LA-6 326
LD-4 326
LG-6 326
LI-2 326
LI-3 326
LM-4 326
LR-1 326
LRA-2 326
LT-6 327
LV-6 327
LW-4 327
LXS-4 327
LINE FILTERS
122253-10A 304
AK-950-FTR 303
LS03-01004 304
MARC 70
Card Cages 359
Dimming Modules
SA 3 359
Diode Isolation
SA 24 358
Logic Inverters
SA 15 357
Switching Module
SR 263 Series 354
SR 343 355
SR 623 356
MARKER BEACON ANTENNAS
CI 102 168
CI 118 169
CI 118-1 170
CI 118-10 172
CI 118-9 171
CI 164 173
CI 165 174
DMN27 Series 175
DMN43 Series 176
MICHEL AVIONICS
3300 Transponder Test Set 329
NC 2210 Tester 328
NAV-AIDS
Commuter/Corporate Aircraft 331
Eurocopter Helicopter 336
Helicopter 337
Military Aircraft 338
Transport/Civil Aircraft 335
NITE LITES 16
NUTS AND WASHERS 24
PHASE SYNC BOXES
3PH-B400 299
EL1 300
PITOT STATIC TUBE
LUN 1150, 1153 390
PLUGS AND JACKS
Data Jacks USB 2
Intercom Kits Accessories 2
Mini Plugs Jacks 2
Plugs Jacks 2
PORTABLE INTERCOM SYSTEMS
DC-COM 200 400
PA 200 400
PA 200E 400
PA 400-3BL / PA 400S-ASC 400
PRESSURE SWITCH
452 392
LUN 1492 391
PUSHBUTTONS TOGGLES
2TC2 Series 14
2TC2 Series 15
41-3 Series 14
7270-1 Series 14
7270-5 Series 14
7270 Series 15
7271-8 Series 14
7271 Series 15
7274 7277 Series 15
7274-11 Series 14
7274-2 Series 14
7277-2 Series 14
7277-5 Series 14
Miniature BAT Toggle 13
Miniature Locking BAT Toggle 13
Miniature Short Toggle 13
Momentary Pushbuttons 13
W23-X1A1G Series 14
PUSHBUTTONS TOGGLES (CONT’D)
W23 Series 15
W31-X2M1G Series 14
W31 Series 15
W58-XC4C12A Series 14
W58 Series 15
RADAR ALTIMETER
CI 152-6 180
RAMI
VHF 198
GPS 199
Navigation 200
DME/Transponder 201
Couplers 202
Mobile/Base 203
Ground/Air Comm 203
Footprints 204
SCREWS 25
SERIALIZERS
IA-RS232C-S 224
3000U 225
SOLDER SLEEVES 12
SPARK TESTERS
AS-1390 423
SPEAKERS 17
SPLITTERS
AV-534 198
AV-534L 198
AV-568 198
AVT-4 198
CI 5120 195
DMH21 196
DMH69-1 197
SWITCHING RELAYS
AIS200-35 362
AIS200-3514 362
AIS240-35 361
AK-950-R 360
T-Bar Hermetically Sealed 363
TEL INSTRUMENTS
Product Selection Guide 316
ARINC 429 321
T-30D 317
T-36C 316
TB-2100 320
TR-211 318
TR-220 319
TABLE OF CONTENTS
7. VIIVII
TEMPERATURE PROBES 392
TERMINAL BLOCKS, BOOTS,
COVERS 10
TEST EQUIPMENT
FDB135 308
RM Series 305
RS-M Series 305
SPC-6-1000-3PH Series 309
SPC6-1500 307
SPC6-1501 307
SPC6-750 Series 306
VLS Series 305
THERMAL PRINTERS
TM-20 421
TIE WRAPS 7
TRANSFORMERS
CC Series 301
CS Series 302
TURN INDICATOR
LUN 1216 381
UHF ANTENNAS
CI 105-20 121
CI 106 122
CI 177-20 123
CI 200 124
UHF ANTENNAS (CONT’D)
CI 271 125
CI 273 126
CI 275-2 127
CI 275-5 128
CI 285 129
CI 306 130
CI 310-20 131
DMC57-1 132
USED TEST EQUIPMENT 312
VERTICAL SPEED INDICATORS
LUN 1141 387
LUN 1144 388
LUN 1149 389
VHF ANTENNAS
CI 108-1, CI 108-1-L 94
CI 108 93
CI 109 96
CI 119 97
CI 121 95
CI 122 98
CI 138 99
CI 139 100
CI 175 101
CI 196 102
CI 211, CI 211-L 103
CI 211-1, CI 211-1-L 104
CI 211-16 105
CI 268-5 106
VHF ANTENNAS (CONT’D)
CI 291 107
CI 292-1 108
CI 292-2 109
DM C50-17 110
DM C60 111
DM C63 112
VINYL TUBING 6
VOR/GS POWER COMBINER
CI 120-3 181
CI 120-4 182
CI 120-5 183
VOR/LOC/GS ANTENNAS
CI 120-200 G/S 135
CI 120-400 136
CI 120 G/S 133
CI 120 G/S-L 134
CI 135-100 137
CI 157P 138
CI 158C 139
CI 158C-2 140
CI 158C-3 141
CI 159C 142
CI 205-3 143
CI 215 144
CI 259E 145
DMN4-15, DM4-33 147
DMN4-17 Series 148
DMN4-45 149
VOR/LOC/GS ANTENNAS (CONT’D)
DMN4-4 System 146
DMN42-1 Loop 150
DMN48 Series Bal. Loop 151
WIRE AND CABLE
ADF Wire 5
ADF Wire Components 5
Coil Cord 5
Fiber Optic Cable 5
High Temp Quadraxial 5
Mil-spec Wire Cable 4
RG Coaxial Cables 4
Shielded Wire 5
Storm Scope Cable 5
Wirespoon 4
WIRE PROCESSING 422
8. VIII
AvionicsInternationalSupplyWebsite
Avionics International Supply, Inc. (AIS) is a combination of three closely held interlinked aerospace
companies, all of which share the same facility in Denton Texas. AIS has been in operation for over 20
years and carries a superlative reputation in the industry. The AIS family of companies focus on four
various segments of the avionics related business.
AVIONICSINTERNATIONALSUPPLY,INC.
* Wholesale distribution of avionics parts and supplies
to private and commercial repair facilities worldwide.
* Manufacture distribution of specialized avionics test
equipment, aircraft lighting accessories and several
one-of-a-kind aviation related items.
* Maintenance, repair, calibration and certification of
avionics and avionics test equipment. (FAA Certified
Class I, II, III IV plus limited accessories, instrument,
radio and accessories repair facility, Repair
Station Number: XI7R807J)
* Sales, Service and Installation of some of the nations
largest instrument and avionics manufacturers
including: Aerosonic, Avidyne, Becker, Garmin,
Honeywell-Bendix/King, L-3 Avionics, Mikrotechna,
Mid-Continent, Sandel, SigmaTek, Sagem Avionics,
and Universal Avionics.
* Acquisition, repair, calibration, certification and resale of
previously owned avionics and avionics test equipment.
ABOUT US...
VIII
9. IXIX
AIS is your full service, one-stop supplier, having the ability to
provide new or used parts and equipment and the capacity to
repair, calibrate and certify the aircraft owners equipment. The AIS
family of companies’strength is best demonstrated by the products
and companies they represent; these include Eaton Aerospace,
BFGoodrich Aerospace, Comant, Tel Instruments, Laversab,
Capital Avionics, Northstar Technologies, Thomas Betts, David
Clark Company Incorporated, Sandia Aerospace, Mid Continent
Instruments, RAMI, and KROY just to name a few.
The history of the companies started with the opening of a
distribution business in 1984 located in Addison Texas. During the
next few years the distribution business was expanded to include an
FAA Class I, II, III and full Class IV instrument repair facility including
accessories category. Further expansion into a full service calibration
shop, the sales of used avionics, and the manufacturing and
development of test equipment and lighting accessories expanded
the company to its current status.
Since 1984, the core companies have built a team of highly
experienced FAA certified technicians and an excellent support
team. The company holds an excellent reputation in the industry
and is considered one of the top three suppliers nation wide in the
avionics market space.
The AIS family of companies’currently services customers across
the spectrum from Major Airlines to General Aviation with a focus
toward Corporate Aviation General Aviation. Major airline
customers include Northwest Airlines, UPS, Continental Airlines,
American Eagle, Frontier, USAir and others, however the core
business is with general aviation repair facilities, Fixed Based
Operations (FBOs) and corporate customers such as Frito Lay,
Honeywell and Boise Cascade Corporation. In addition, sales to
Government entities such as the Department of the Navy, U.S.
Customs and Border Protection, U.S. Air Force and Army National
Guard demonstrate the variety in our customer base. The company
also supports many key OEMs such as Raytheon Aerospace,
Gulfstream, Beechcraft, Cessna, Eclipse and Learjet.
Over the past fourteen years AIS has developed a strong customer
base in the International market. Some of our Top 100 International
customers include: ST Aerospace Engineering; Hawker Pacific;
Scandinavian Avionics; Lufthansa; Euro copter; Bombardier and
Beechcraft International.
Aerospace Instrument Support, Inc. is the organizations class I, II, II
IV, FAA, JAA, and EASA Certified Instrument and Avionics Repair
and Installation facility with limited Accessory and Avionics rating
including Weather Radar and Transponder repair and overhaul
capabilities as well as being the only Factory Authorized Service
Center in North America for KANNAD ELTs. Aerospace is also an
authorized Dealer and Installation facility for some of the largest
Instrument and Avionics Manufacturers including: Aerosonic,
Avidyne, Becker, Garmin, Honeywell Bendix/King, L-3 Avionics,
Mikrotechna, Mid-Continent, Sandel, SigmaTek, Sagem, and
Universal Avionics.
PROVIDING THE BEST PRODUCTS, SERVICE,
AND SUPPORT IN THE AVIONICS INDUSTRY
SINCE 1984.
IX
10. X
A world leader in the manufacturing of Pitot/Static
ground support equipment. Not only is Aerospace
the manufacturer of new products, we have a highly
advanced avionics and instrument certification and repair
facility. Aerospace has its own on site calibration equip-
ment that well exceeds NIST standards. As a Part 145
certified repair station CRS # XI7R807J, Aerospace has
the lab and technical ability for repairs and certification
of most manufacturers of avionics and instruments, as
well as Pitot/Static and RVSM test boxes.
Aerospace Instrument Support is your source for instru-
ment repair and overhaul. A Class I, II, III and partial
IV CRS with FAA/JAA approval, Aerospace Instrument
Support can provide overhall / exchange as well as quick
turn times with competitive pricing. Give us a call for all
of your instrument needs.
We specialize in Pitot / Static Test Equipment and
RVSM Test Sets including Manufacturing and
Certifications. Typical turn around times are between 3
to 5 days!
For more information, please contact:
Brenda Leavell
Quality Manager
brenda@ais-inst.com
Kevin Summerlin
General Manager
kevin@ais-inst.com
INSTRUMENT SUPPORT, Inc.
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Me
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma
Aerosonic Sandel Epo-Aire Kannad Dav
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et /
Kollsman / DC General Electric Century C A
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
GeneralDesignDruck
Ametek/USGuageAstronautics
AerosonicSandel
ArteSmiths
Kollsman/DCGeneralElectri
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
GeneralDesign
Ametek/USGuage
Aerosonic
Arte
Kollsman/DC
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
Castleberry Aero Mechanism
ent N.A.T. Sigma-Tek
Kannad Davtron
/ King / Sperry
United nstruments et / A M
C A
Castleberry Aero Mechanism
N.A.T. Sigma-Tek
Kannad Davtron
ng / Sperry
United nstruments et / A M
C A
ign Druck Barfield Castleberry Aero Mechanism
Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
DC General Electric Century C A
Aero Mechanism
Sigma-Tek
Davtron
ents et / A M
n Druck Barfield Castleberry Aero Mechanism
age Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
Barfield Castleberry Aero Mechanism
ics Mid Continent N.A.T. Sigma-Tek
Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Collins United nstruments et / A M
ctric Century C A
Barfield Castleberry Aero Mechanism
Mid Continent N.A.T. Sigma-Tek
Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Collins United nstruments et / A M
ic Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
Castleberry Aero Mechanism
N.A.T. Sigma-Tek
Kannad Davtron
ng / Sperry
United nstruments et / A M
C A
Castleberry Aero Mechanism
ent N.A.T. Sigma-Tek
Kannad Davtron
/ King / Sperry
United nstruments et / A M
C A
ign Druck Barfield Castleberry Aero Mechanism
Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
DC General Electric Century C A
n Druck Barfield Castleberry Aero Mechanism
age Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstrum
Kollsman / DC General Electric Century C A
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
GeneralDesignDruckBarfiel
Ametek/USGuageAstronauticsMidConti
AerosonicSandelEpo-Air
oneyell/Bendi
ArteSmithsCollins
Kollsman/DCGeneralElectricCentur
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments
Kollsman / DC General Electric Century C A
Druck Barfield Castleberry Aero Mechanism
e Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
General Electric Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
Barfield Castleberry Aero Mechanism
Mid Continent N.A.T. Sigma-Tek
Epo-Aire Kannad Davtron
ey ell / Bendi / King / Sperry
Collins United nstruments et / A M
Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
General Design Druck Barfield Castleberry
Ametek / US Guage Astronautics Mid Continent N.A.T.
Aerosonic Sandel Epo-Aire Kannad
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments
Kollsman / DC General Electric Century C A
Druck Barfield Castleberry Aero Mechanism
e Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
General Electric Century C A
Barfield Castleberry Aero Mechanism
Mid Continent N.A.T. Sigma-Tek
Epo-Aire Kannad Davtron
ell / Bendi / King / Sperry
Collins United nstruments et / A M
Century C A
General Design Druck Barfield Castleberry Aero Mechanism
Ametek / US Guage Astronautics Mid Continent N.A.T. Sigma-Tek
Aerosonic Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Arte Smiths Collins United nstruments et / A M
Kollsman / DC General Electric Century C A
Druck Barfield Castleberry Aero Mechanism
e Astronautics Mid Continent N.A.T. Sigma-Tek
Sandel Epo-Aire Kannad Davtron
oney ell / Bendi / King / Sperry
Smiths Collins United nstruments et / A M
C General Electric Century C A
Aerospace Instrument Support, Inc.
AEROSPACE INSTRUMENT SUPPORT
Aerospace Instrument Support is an industry leader in the
overhaul and repair of an assortment of gyroscopes and
avionics instruments, and is a full service FAA and EASA
approved instrument repair facility. Aerospace offers far
more than just an extensive list of gyroscope products
and services, Aerospace can repair Pressure Instruments,
Engine Instruments, and External Aircraft Lighting and
Powersupplies.Currently, Aerospace Instrument Support has
the capabilities of repairing, overhauling, and performing a
full functional test including: Collins Proline II, Transponders,
DME’s, Radar, Nav / Comm, ADF, VHF, Control Heads, and
ARINC Avionics.
11. XIXI
Call For Complete Capabilities Listing
Aerospace Instrument Support is an approved FAA repair station #X17R807J.
VSI TYPE
AEROSONIC
30020-( ) 2000 FPM
30030-( ) 3000 FPM
30040-( ) 4000 FPM
30060-( ) 6000 FPM
30230-( ) 3000 FPM
30240-( ) 4000 FPM
30260-( ) 6000 FPM
35060-( ) 6000 FPM
35160-() 6000 FPM
UNITED
7000 2000 FPM
7030 3000 FPM
7040 4000 FPM
7060 6000 FPM
GYRO TYPE
A.l.M.
200-( ) DIR. GYRO
205-( ) DIR. GYRO
251 -( ) HOR GYRO
300-( ) FLT. DIR.
305-( ) FLT. DIR.
500-( ) HOR. GYRO
510-() DIR. GYRO
52D54-( ) DIR. GYRO
52D66-( ) HOR. GYRO
52D67-( ) HOR. GYRO
EDO-AIRE
52C77-( ) FLT. DIR.
52D54-( ) DIR. GYRO
52D66-( ) HOR. GYRO
52D67-( ) HOR. GYRO
52D136( ) H.S.I.
52D137-( ) H.S.I.
52D154-( ) DIR. GYRO
52D166-( ) HOR. GYRO
52D167-( ) HOR. GYRO
52D177-( ) FLT. DIR.
52D254 DIR. GYRQ
GYRO TYPE
EDO-AIRE
52D266-( ) HOR. GYRO
52D267-( ) HOR. GYRO
G502-( ) DIR. GYRO
G504-( ) DIR. GYRO
G519-( ) HOR. GYRO
G520-( ) DIR. GYRO
G550-( ) FLT. DIR.
G1050-( ) FLT. DIR.
IG832-( ) H.S.I.
J.E.T.
Al804 STBY. GYRO
Al903 STBY. GYRO
Al904 STBY. GYRO
KING
Kl-255-( ) FLT. DIR.
Kl-256-( ) FLT. DIR.
KG-102-() DIR. GYRO
KG-107-( ) DIR. GYRO
KG-258-( ) HOR. GYRO
KSG-105-( ) DIR. GYRO
Kl525A-( ) H.S.I.
SPERRY
C-14-() DIR. GYRO
VG-14-( ) HOR. GYRO
GH-14-( ) HOR. GYRO
COLLINS
332D-11-( ) VERT. GYRO
332E-4-( ) DIR. GYRO
ADI/HIS TYPE
COLLINS
329B-7-( ) ADI
329B-8-( ) ADI
331A-3-( ) H.S.I.
331A-6-( ) H.S.I.
331A-8-( ) H.S.I.
332C-10-( ) H.S.i.
INSTRUMENT REPAIR AND OVERHAUL
AEROSPACE INSTRUMENT SUPPORT
12. XII
CALIBRATION
We are ANSI Z540 compliant and qualified to calibrate
and repair your avionics test equipment and tools. We
provide quick turn around times without sacrificing quality
service.
ATEC
Authorized Tel-Instruments Service Center
TR-220:Multi-functionTestSet
RD300:WeatherRadarTestSet
TektronixOscilloscope
ATC600A:DME/TransponderTestSet
Avionics Test Equipment Calibration
Call For A Quote
PHONE 940-566-3245
TOLL FREE 800-768-3008
FAX 940-566-9506
13. 1InstallationSupplies
Installation Supplies
Plugs and Jacks 2
Data Jacks USB
Intercom Kits Accessories
Mini Plugs Jacks
Plugs Jacks
Jack Housings 3
Cover/Reducer Plates 3
Dzus Rail
Instrument Cover Plates
Mu-Metal
Reducer Plates
Sqeeze Clamps
Wire and Cable
ADF Wire 5
ADF Wire Components 5
Coil Cord 5
Fiber Optic Cable 5
High Temp Quadraxial 5
Mil-spec Wire Cable 4
RG Coaxial Cables 4
Shielded Wire 5
Storm Scope Cable 5
Wirespoon 4
Vinyl Tubing 6
Brass and Nylon Fittings 6
Tie Wraps 7
Cable Mounts and Fasteners 8
Cable Tie Mounts
Braided Nylon Lacing Cord
Cradle Cable Tie Mounts
Expandable Sleeving
Lightning Hole Cable Tie Mount
Loop Type Fastener ADEL Clamp
Spiral Wrap
Heat Shrink Tubing 9
Copper Buss Bar 10
Colored Breaker Collars 10
Circuit Breaker Safety Locks 10
Grommets 10
HEX Standoffs 10
Terminal Blocks, Boots, Covers 10
Test Kits and Accessories 11
Solder Sleeves 12
Environmental Splices 12
Fuses 12
Pushbuttons and Toggles
2TC2 Series 14
2TC2 Series 15
41-3 Series 14
7270-1 Series 14
7270-5 Series 14
7270 Series 15
7271-8 Series 14
7271 Series 15
7274 7277 Series 15
7274-11 Series 14
7274-2 Series 14
7277-2 Series 14
7277-5 Series 14
Pushbuttons and Toggles (Cont)
Miniature BAT Toggle 13
Miniature Locking BAT Toggle 13
Miniature Short Toggle 13
Momentary Pushbuttons 13
W23-X1A1G Series 14
W23 Series 15
W31-X2M1G Series 14
W31 Series 15
W58-XC4C12A Series 14
W58 Series 15
Nite Lites 16
Speakers 17
Connectors and Adapters
BNC Adapters 19
BNC Connectors 18
GPS Notch Filter 18
N Type Connectors 19
SMA UHF Connectors 19
TNC Connectors 18
Tray Mount RF Connector 18
Connectors and Pins
AC/DC Recepticles 23
ARC Transponder Contacts 21
Block Receptacle 20
Clamps 23
Grounding Blocks 20
HD Positioner 21
HD Sub-D Connectors 21
Insertion/Extraction Tools 23
King Double Edge Pins 21
Male Jack Screws 20
Mate-N-Lok Connectors 21
Metrimate Connectors 20
Narco Contacts 21
“PIDG” Splices 20
“PIDG” Splices 20
“PIDG” Terminals 20
“Round Tongue” Terminals 20
“Solistrand” Ring Terminals 20
“Terminal” Ring Terminals 20
Power Connectors 22
Reverse Sex Connectors 22
CPC Connectors 22
Sockets For Grounding 20
Pins 22
Standard Sex Connectors 22
Subminiature D Connectors 21
Wire Caps 20
Nuts and Washers 24
Screws 25
Crimpers and Wire Strippers 26
Replacement Die Sets 27
Label Makers
K-Sun 29
KROY 28
Cooling Fans 30
Cooling Hose 31
Heat Guns 32
Heat Gun Accessories 36
14. 1InstallationSupplies
PLUGS JACKS
PLUGS JACKS
DATA JACKS USB
The images in these diagrams are not to scale.
MINI PLUGS JACKS
NEXUS / SWITCHCRAFT
PJ055B
(Mono)
JJ034
(Mono) With key
SWC11
(Mono) Unkeyed
VE055J
(Mono)
TP-101
(U 174/U)
TP-102
(U 93A/U)
TJT-120
(U 92B/U)
TJ-120
(U 92B/U-R)
TJ-102
(U 92A/U)
TJS-102
V94A/V
(With Clip)
PJ068
JJ033
(With key)
S12B
(JJ033 Unkeyed)
VEO68J
(JJ033 Inline)
SP200
(Stereo)
12B
(Stereo)
SJ 200
(Stereo)
MP-101
(U 173/U)
MJ-101
(U 172/U)
27-655
Mini Stereo Jack
27-060
Mini Stereo Plug
INTERCOM KITS ACCESSORIES
P/N IC2-KIT 2 Place (mono) Intercom Kit
P/N IC2S-KIT 2 Place (stereo) Intercom Kit
P/N IC4-KIT 4 Place (mono) Intercom Kit
P/N IC4S-KIT 4 Place (stereo) Intercom Kit
P/N IC6-KIT 6 Place (mono) Intercom Kit
P/N IC6S-KIT 6 Place (stereo) Intercom Kit
(all kits include mic/phone jacks and washers)
S1028 Flat Washer (Insulating)
S1029 Shoulder Washer
P/N ARJ11 RJ11 Jack (no bezel)
P/N ARJ11W RJ11 Jack w/6” pigtail
P/N ARJ11WC RJ11 Jack w/6” pigtail connector
P/N ARJ45 RJ45 connector
P/N ABE06-00 RJ11 Bezel
P/N ABE06-00D RJ11 Bezel “DATA”
P/N ABE06-00F RJ11 Bezel “FAX”
P/N ABE06-00V RJ11 Bezel “VOICE”
P/N ABE06-00M RJ11 Bezel “MODEM”
P/N ABE06-00L RJ11 Bezel “LAN”
P/N ABE08-00 RJ45 Bezel
P/N ABE08-00D RJ45 Bezel “DATA”
P/N ABE08-00L RJ45 Bezel “LAN”
12 colors to choose from (CALL AIS)
USB-AB
USB-BB
TJ-101
15. 1InstallationSupplies
JACK HOUSINGS
COVER/REDUCER PLATES
Part # Description
FAP09-1 1 hole/under panel mount
FAP09-2 2 hole/under panel mount
FAP09-3 4 hole/under panel mount
FAP09-4 4 hole/horizontal mount
FAP09-3 FAP09-4FAP09-1 FAP09-2
FAP09 Series
All FAP09 series mic jack housings are made from
aluminum and feature a crinkle finish.
Ashtray Mountable Jack Housing
P/N AVB
Mu-Metal Used to cover and protect electronic equipment.
P/N Width
MU Metal 4 4”
Mu Metal 15 15”
Dzus Rail Custom cut in any size up to 5 feet.
P/N
PR3.5-1X5 (Flat Rail)
PR3.5X5 (Rt. Angle Rail Rail)
PFSC3538A (Fastener)
TP35AHT (Fastener Tool)
Angled Rail
Flat Rail
Fastener
Sqeeze Clamps
P/N Description
9963B 3 ATI Sqeeze Clamp 1” deep
64311B 3 ATI Sqeeze Clamp 2” deep
Made of a durable, crinkle finished plastic, ideal for
temporary or permanent panel changes.
P/N: FAP05-2
(3-1/8” Cover Plate)
P/N: FAP05-3
(3” ATI Cover Plate)
P/N: FAP05-5
(1/2 ATI Cover Plate)
P/N: FAP05-1
(2-1/4” Cover Plate)
Instrument Cover Plates
Reducer Plates
FAP04-1
(3-1/8-to 2-1/4”)
FAP04-2
(any gyro to 3-1/8”)
FAP04-4
(3ATI to 2-1/4”)
FAP04-3
(3ATI to 3-1/8”)
NOT PMA’d. The KX-99A offers tremendous security from radio failure for
very little cost. Designed to go in-line with a COM antenna coax, the KX-99A
disconnects the aircraft radio from the antenna when you plug in the adapter
cable. The handheld transeiver will now receive and transmit on an external
aircraft antenna. You can re-establish the connection between the aircraft
radio and COM antenna by simply unplugging the KX-99A adapter cable.
KX-99A Handheld Transceiver Adapter
All FAP08 series mic jack housings are made from aluminum
and feature a crinkle finish.
Part # Description
FAP08-1 Black housing
FAP08-2 Tan housing
FAP08-3 Raw aluminum housing
FAP08-4 Black flush mount
w/bracket
FAP08 Series
Part # Description
FAP08-5 Tan flush mount w/bracket
FAP08-6 Un-painted flush mount
w/bracket
FAP08-7 Black dual place housing
FAP08-8 Tan dual place housing
16. 1InstallationSupplies
WIRE CABLE
MIL-W-22759/16 Standard Wall
Conductor: Tin Plated Copper Insulation: TEFZEL
Voltage Rating: 600V Temperature Rating: 150°C (302°F)
Replace x with color code
Mil-W-22759/16 wire incorporates a standard wall of
ETFE (ethylene tetrafluoroethylene) insulation. This
wire is designed for aerospace applications where
light weight, tight tolerances and excellent mechani-
cal toughness are required. This insulation offers
exceptional radiation and chemical resistance.
Conductor:
Mil-W-22759/16 - Tin plated copper
RG393RG179RG142
Wirespoon
P/N SP1
Mil-spec Wire Cable
ID No. Base Color ID No Base Color or Band First Stripe or Band Second Stripe
0 Black 90 White Black
1 Brown 91 White Brown
2 Red 92 White Red
3 Orange 93 White Orange
4 Yellow 94 White Yellow
5 Green 95 White Green
6 Blue 96 White Blue
7 Violet 97 White Violoet
8 Gray 98 White Gray
9 White 901 White Black Brown
902 White Black Red
Part Number Gauge Stranding Insulation O.D. (Min-Max) Nominal Wt. (lbs/1000’)
22759/16-24-x 24 19/36 .043-.047 2.45
22759/16-22-x 22 19/34 .050-.054 3.52
22759/16-20-x 20 19/36 .058-.062 5.18
22759/16-18-x 18 19/30 .069-.073 7.65
22759/16-16-x 16 19/29 .077-.081 9.68
22759/16-14-x 14 19/27 .091-.095 14.50
22759/16-12-x 12 37/28 .111-.117 21.80
22759/16-10-x 10 37/26 .136-.142 34.00
22759/16-8-x 8 133/29 .196-.202 61.50
22759/16-6-x 6 133/27 .247-.253 96.90
22759/16-4-x 4 133/25 .308-.316 152.00
22759/16-2-x 2 665/30 .384-.392 231.00
RG/U No. Jkt. OD Jkt. Type OD Type Dielectric Center Cond. Nom. Imped. Ohms Max Operating Volt. (Rms) Engineering Data
RG58 C/U .195 IIa .116P 19/.0071TC 50.0 1900
RG59 C/U .242 IIa .146P .023CW 75.0 2300
RG142 B/U .195 IX .116T .039SCW 50.0 1900
RG179 .105 IX .093T 7/.04SCW 75.0 1200 High temp miniturized cable
RG188 A/U .110 VII .060T 7/.0067SCW 50.0 1200 High temp miniturized cable
RG213 U .405 IIa .285P 7/.0296C 50.0 3000 Formerly 8A/U
RG214 .425 IIa .285P 7/.0296S 50.0 3000 Formerly 9B/U
RG393 .390 IX .285T 7/.0312 50.0 5000 Moisture proof RG225
RG400 .195 IX .116T 19/.007SPC 50.0 1900 Same as RG142 except stranded center conductor
RG Coaxial Cables
17. 1InstallationSupplies
WIRE CABLE
XXTG1T14 XXTG3T14
XXTG2T14 XXTG4T14 P/N 14379 (M6370-1) P/N AN 181
22TG2T14
Guage
Basic Wire
No. of Conductors
Shield Style
Jacket
Shielded Wire
Part Number No. of Conductors Part Number No. of Conductiors
12TG2T14 2 20TG3T14 3
14TG1T14 1 20TG4T14 4
14TG2T14 2 22TG1T14 1
16TG1T14 1 22TG2T14 2
16TG2T14 2 22TG3T14 3
18TG1T14 1 22TG4T14 4
18TG2T14 2 24TG1T14 1
20TG1T14 1 24TG2T14 2
20TG2T14 2 24TG3T14 3
Recommended Temp. Limit: 302˚ F (150˚ C)
MIL Number: M27500/18
7 Conductor 24 awg coil cord BlackCoil Cord
Storm Scope Cable
P/N 480-891 WX1000 Synchro Cable Clear
P/N 481-891 WX1000 Antenna Cable Blue
P/N 482-891 WX1000 Display Cable Red
Fiber Optic Cable
P/N HCP-M0200T-D01FS
High Temp Quadraxial Cable
P/N D07802-100
ADF Wire
P/N AN 181 Solid Copper Antenna Wire
P/N 14379 ADF Coated Antenna Wire
P/N 801-175 ADF Coated Antenna Wire
P/N 8603
P/N NAF1086-4
P/N10-125
ADF Wire Components
P/N 8603 Strain Insulator
P/N 10-125 Feed Thru Insulator
P/N NAF1086-4 Tension Spring
Black - P/N 95-13576-00
Gray - P/N AIS/CC
AIS Laser Wire Marking Services
See page 412 for more details.
18. 1InstallationSupplies
Poly-Flo Tube Cutter
P/N 307-FP
Poly-Flo Tubing
Imperial Eastman Poly-Flo Tubing.
To be used with Imperial Eastman
Nylon and Brass Fittings.
100 Foot Roll, P/N 44PE
IMPERIAL EASTMAN
Nylon Fittings
Union Elbow
265N04
Female Connector
266N04x02
Male Connector
268N04x02
Male Elbow
269N04x02
Male Run Tee
271N04x02
Male Branch Tee
272N04x02
Bulkhead Union
282N04
Female Elbow
270N04x02
Inline Connector
262N04
Union Tee
264N04
Nut
261N04
Insert Stabilizer
259N04
Not Shown: Plug P/N 259P04
Brass Fittings
Male Run Tee
271P04x02
Nut
261P04
Male Run Tee
282P04
Union Tee
264P04
Male Branch Tee
272P04x02
Inline Connector
262P04
Male Elbow
269P04x02
Male Connector
268P04x02
Female Connector
266P04x02
Nylon Insert Fittings Used with 1/4” hose or tubing
Tee Connector
716-153
Elbow Connector
711-153
Inline Connector
701-153
Tee Connector
716-015
Elbow Connector
711-015
Inline Connector
706-015
VINYL TUBING
FITTINGS
P/N Diameter Length
SLV-105-1/4 1/4” 100’
SLV-105-3/8 3/8” 100’
SLV-105-7/16 7/16” 100’
SLV-105-1/2 1/2” 100’
SLV-105-9/16 9/16” 100’
SLV-105-5/8 5/8” 100’
SLV-105-3/4 3/4” 100’
SLV-105-7/8 7/8” 100’
SLV-105-1 1” 100’
Vinyl Tubing
Vinyl Tubing is an extremely flexible material designed
primarily for low temperature applications.
Conforms to MIL-1-6310.
20. 1InstallationSupplies
Lightning Hole Cable Tie Mount
P/N LHMS-S6-D “No.6
P/N LHMS-S10-D “No.10
Tyton P/N Panduit P/N Strength Mounting
MB-3A ABMM-A-D 18 to 30lbs. #4 Screw
MB-4A ABM112-A-D 18 to 50lbs. #8 Screw
MB-5A ABM3H-A-L 18 to 150lbs. #8 Screw
Adhesive Screw Cable Tie Mounts
Tyton P/N Panduit P/N Strength Mounting
CTM-0 TM2S6-C 18lbs. #6 Screw
CTM-1 TM2S8-C 18lbs. #8 Screw
CTM-2 TM3S8-C 18 to 50lbs. #8 Screw
CTM-3 TM3S10-C 18 to 50lbs. #10 Screw
CTM-4 TM3S25-C 18 to 120lbs. 1/4” Screw
Cradle Cable Tie Mounts
P/N Size
MS21919WDG10 5/8”
MS21919WDG 11 11/16”
MS21919WDG12 3/4”
MS21919WDG13 13/16”
MS21919WDG14 7/8”
MS21919WDG15 15/16”
MS21919WDG16 1 “
MS21919WDG17 1 1/16”
MS21919WDG18 1 1/8”
MS21919WDG19 13/16”
MS21919WDG2 1/16”
MS21919WDG20 1 1 /4”
MS21919WDG21 15/16”
MS21919WDG22 1 3/8”
MS21919WDG3 1/8”
MS21919WDG4 3/16”
MS21919WDG5 5/16”
MS21919WDG6 3/8”
MS21919WDG7 7/16”
MS21919WDG8 1/2”
MS21919WDG9 9/16”
Loop Type Fastener ADEL Clamp
P/N Size Range
XSL1/8-FR 3/32 to 1/8
XSL1/8W-FR 3/32 to 1/8
XSL1/4 FR 1/8 to 3/8
XSL1/4W-FR 1/8 to 3/8
XSL3/8-FR 1/4 to 1/2
XSL3/8W-FR 1/4 to 1/2
XSL1/2-FR 1/4 to 3/4
XSL1/2W-FR 1/4 to 3/4
P/N Size Range
XSL3/4W-FR 1/2 to 1
XSL1-1/4-FR 1/2 to 1 1/4
XSL1-1/4W-FR 1/2 to 1 1/4
XSL1 3/4-FR 3/4 to 1 1/2
XSL1 3/4W-FR 3/4 to 1 1/2
XSL2-FR 1 1/4 to 2 1/2
XSL2W-FR 1 1/4 to 2 1/2
Expandable Sleeving
Designed for applications where full cover-
age abrasion protection and fray resistance
is a requirement.
Panduit product available by request.
P/N MaxDia.
SWP1/8 1/2
SWP3/16 1-1 /2
SWP1/4 2
SWP3/8 3
P/N Max Dia.
SWP1/2 4
SWP3/4 6
SWP1 8
Spiral Wrap
Used for long continuous runs where
individual leads may be required to
break out at any given point. Comes
in 100’ spool, Natural or Black.
Panduit product available by request.
P/N Color Width Length
50NOF17B Black .085 500Yds
50NOF17W White .085 500Yds
Braided Nylon Lacing Cord
Lacing cord meets MilT43435B and
comes with a sure grip coating. 500
yard spools available in either black
or white.
CABLOE MOUNTS AND FASTENERS
21. 1InstallationSupplies
Heat Shrink Tubing
Used for insulating, jacketing, bundling and identification. Shrinks between 200° and 300° C are recommended. Shrinkage is
less than 5%. MIL-1-23053B/5, Classes 1 and 2. Sold in four foot sticks, and by the 100’ roll.
Part Number Diameter
HIX364 3
/64”
HIX116 1
/16”
HIX332 3
/32”
HIX18 1
/8”
HIX316 3
/16”
HIX14 1
/4”
HIX38 3
/8”
HIX12 1
/2”
HIX34 3
/4”
HIX1 1”
Part Number Diameter
HSTT05 3
/64”
HSTT06 1
/16”
HSTT09 3
/32”
HSTT12 1
/8”
HSTT19 3
/16”
HSTT25 1
/4”
HSTT38 3
/8”
HSTT50 1
/2”
HSTT100 1”
HSTT150 11
/2”
HSTT200 2”
PanduitTitan
Available Colors:
100’ Black White
4’ Black White Clear
Red Blue
Available Colors:
Black White Clear
Red Blue
HEAT SHRINK TUBING
22. 10
1InstallationSupplies
Color code your flight critical
circuit breakers with colored
breaker collars.
CB Colored Breaker Collars
P/N Color
10164-1 Black
10164-2 Ivory
10164-3 White
10164-4 Orange
10164-5 Red
10164-7 Green
10164-8 Gray
10164-9 Yellow
10164-10 Blue
Copper Buss Bar with Cadmium Plating
P/N MS25226-2-20 6-32 Holes Bus Bar
P/N MS25226-10-16 8-32 Holes Bus Bar
Terminal Block Covers
MS18029-1S-5 Terminal block cover
MS18029-1S10 Terminal block cover
MS18029-1S20 Terminal block cover
MS18029-23 Knob, Terminal cover
MS18029-6S-16 Terminal block cover
MS18029-6S-2 Terminal block cover
MS18029-6S-8 Terminal block cover
Keeps circuit breakers from being
accidentally closed when connected
to equipment that has been removed
or is under repair.
P/N S4933959-511 Safety Lock (No Tag)
P/N S4933959-531 Safety Lock with “Inoperative” tag
Circuit Breaker Safety Locks
HEX Standoffs
1/4” outer diameter HEX aluminum
HTA-4-250A 4-40 thread, 1/4” length
HTA-4-500A 4-40 thread, 1/2” length
HTA-4-750A 4-40 thread, 3/4” length
HTA-4-1000A 4-40 thread, 1” length
HTA-6-250A 6-32 thread, 1/4” length
HTA-6-500A 6-32 thread, 1/2” length
HTA-6-750A 6-32 thread, 3/4” length
HTA-6-1000A 6-32 thread, 1” length
HTA-8-250A 8-32 thread, 1/4” length
HTA-8-500A 8-32 thread, 1/2” length
HTA-8-750A 8-32 thread, 3/4” length
HTA-8-1000A 8-32 thread, 1” length
Grommets
Vinyl grommet
G402 3/16” ID x 5/16” OD
G403 1/4” ID x 3/8” OD
G404 5/16” ID x 7/16” OD
G405 3/8” ID x 1/2” OD
G406 1/2” ID x 5/8” OD
MS27212-1-20 6-32 Terminal block
MS27212-2-16 10-32 Terminal block
MS27212-6-16 8-32 Terminal block
And Many More! Call AIS
Terminal Blocks
MS25171-1S
MS25171-2S
MS25171-3S
MS25171-4S
Terminal Boots
23. 11
1InstallationSupplies
Aeronautical Test Kit
A safe, quick and easy way to test 99% of all connectors in the aircraft. Kit includes
both male and female inserts of the six most common sizes for ringing out all wiring.
Compact wallet for easy storage.
Additional back up pins and socket test leads are available.
Part No 129392
Insulated Clip
Part No 126087/Color
Maximum jaw opening 26mm (1 inch)
IEC 61010 Rating: 600 Volts CAT III 1000 Volts Cat II ™ 20Amps
Standard colors: Black, Red, Green, Blue, Yellow, White.
Sprung Hook
Part No 121332/Color
IEC 61010 RATING: 1000 Volts CAT III ™ 30 Amps Standard Colors: Black, Red
Part No 121331/Color
IEC 61010 Rating: 1000V Cat III ª 30Amps Standard Colors: Black, Red
Thin Spike Test Prod
Part No 126088/Color
Maximum jaw opening 24 mm (9.5 inches) IEC 61010
Rating: 1000 Volts CAT III ™ GS 38 Compliant
Fused Insulated Clip
Fused Prod
Part No 121335/Color
Fuse Rating 500mA/1000V/50kA Replace fuse P/N: 116048
GS 38 Compliant IEC 61010 RATING: 1000 Volts CAT III ª
Standard Colors: Black, Red
Part No 124162/Color
Each extender increases the reach of the pins by approx 75 mm (3 Inches)
Standard Colors: Black, Red
Extenders
Part No 134328/Color
One end of the lead is terminated in a 4mm right-angled plug; the other has a 4mm
socket into which the original lead is plugged. Designed to be robust and sturdy.
IEC 61010 Rating: 1000 Volts CAT III ™ 20Amps
40’ Extender Reel
Part No 121333/Color
For cables 2 mm-4 mm (0.080-0.16 inches) Ideal for Automotive other applications.
Note: Recommended for safe voltage piercing only. IEC 61010 RATING: 1000 Volts CAT
III ª 10 Amps Standard Colors: Black, Red
Cable Piercer
TEST KITS AND ACCESSORIES
24. 12
1InstallationSupplies
AGC Fast Blow Fuses MDL Slow Blow Fuses
Solder Sleeves Environmental Splices
P/N ALT#
SLC745-14 SMALL(.125) LC-2
SLC745-15 MEDIUM(.200) LC-3
SLC745-16 LARGE(.300) LC-5
P/N ALT#
M83519/2-1 Small / 20 Awg Lead HML-1
M83519/2-2 Medium / 20 Awg Lead HML-2
M83519/2-3 Large / 20 Awg Lead HML-3
M83519/2-7 Medium / 22 Awg Lead HML-7
M83519/2-8 Large / 22 Awg Lead HML-8
M83519/2-9 X Large / 22 Awg Lead HML-9
P/N ALT#
M81824/1-1 Red, Raychem Env. Splice D436-36
M81824/1-2 Blue, Raychem Env. Splice D436-37
M81824/1-3 Yellow, Raychem Env. Splice D436-38
Used for wire splicing where size
and weight reduction and environ-
mental sealing are critical.
P/N AMP P/N AMP P/N AMP P/N AMP
AGC1 1 AGC5 5 MDL1 1 MDL5 5
AGC2 2 AGC7 7 MDL2 2 MDL7 7
AGC3 3 AGC10 10 MDL3 3 MDL10 10
AGC4 4 AGC15 15 MDL4 4 MDL15 15
SOLDER SLEEVES
FUSES
Fuse Holders
Crimp
P/N HHB
with Leads
P/N 150145A
Panel Mount
P/N 342014
Ray Chem P/N: AD-1377
Alt P/N: 3137CT
Daniels: GMT232
Environmental Crimpers
25. 13
1InstallationSupplies
TYCO/ALCO/GRAYHILL
Miniature BAT Toggle
Miniature Locking BAT Toggle
SPDT Alt #
MTA-106D 1571920-3 On None On
MTA-106E 1571320-5 On Off On
MTA-106F 1571920-7 On None On
MTA-106G 1571920-9 On Off On
MTA-106H 1571920-1 On Off On
MTA206PA 1-1571920-1 On On On
MTA206R 2-1571920-1 On None On
MTA206S 2-1571920-3 On Off On
MTA206T 2-1571920-7 On Off On
MTA206TA 2-1571920-8 On On On
DPDT Alt #
MTA-206N 1-1571920-5 On None On
MTA-206P 1-1571920-7 On Off On
3PDT Alt #
MTA-306D 3-1571920-0 On None On
MTA-306E 3-1571920-2 On Off On
4PDT Alt #
MTA-406N 3-1571920- On None On
MTA-406P 4-1571920-0 On Off On
SPDT Alt #
MTL-106D 1571927-2 On None On
MTL-106E 3-1437559-5 On Off On
3PDT Alt #
MTL-306D 1-1571927-0 On None On
DPDT Alt #
MTL-206N 1571927-5 On None On
MTL-206P 1571927-7 On Off On
4PDT Alt #
MTL-406N 1-1571927-2 On None On
Momentary Pushbuttons
MPA-206N DPDT
MPA-206R DPDT (mom)
MPA-103F SPDT, Black
MPA-306F 3PDT (mom)
611-4302 Mason Switch
PTT Switch that goes in
most Cessna Aircraft
• Reliable
• Economical
• UL Recognized
• CSA Certified
P/N 30-1 Black
30-2 Red
30-3 Black
Sub-miniature momen-
tary push button used
in most Piper, PA-24
PA-28 Series airplanes
for PTT Switches
P/N 39-1
Sub-miniature momen-
tary push button. This
is a N/C Switch. Can be
used in some Autopilot
installs.
P/N 39-2
39-3 Short
PUSHBUTTONS AND TOGGLES
SPST: Norm Open, 1/4” Threads
MSPS-103C0 Black
MSPS-103C2 Red
2 Circuit, Norm Open - Norm Closed, 1/2” Threads,
MSPF-101BC0 Black
MSPF-101BC2 Red
Miniature Short Toggle
P/N Alt #
MTG106D04 1571926-3 On None Off
MTG106E04 1571926-4 On Off On
MTF106D 1571925-3 On None On
MTF106G 1571925-6 On Off On
MTF206N 1-1571925-6 On None On
MTF206T 2-1571925-2 On Off On
26. 14
1InstallationSupplies
7274 Mil Spec’d same size as 7277 Series.
7277-5-.5
7277-5-.75
7277-5-1
7277-5-1.5
7277-5-2
7277-5-2.5
7277-5-3
7277-5-5
7277-5-7.5
7277-5-10
7277-5-15
7277-5-20
7277-5 Series
7270-5-3
7270-5-5
7270-5-10
7270-5-15
7270-5-20
7270-5-25
7270-5-30
7270-5-35
7270-5 Series
2TC2-1
2TC2-2
2TC2-2.5
2TC2-3
2TC2-4
2TC2-5
2TC2-7.5
2TC2-10
2TC2-15
2TC2-20
2TC2 Series
7271-8-3
7271-8-5
7271-8-7.5
7271-8-10
7271-8-15
7271-8-20
7271-8-25
7271-8-30
7271-8-35
7271-8 Series
7270-1-3
7270-1-5
7270-1-7.5
7270-1-10
7270-1-15
7270-1-20
7270-1-25
7270-1-30
7270-1-35
7270-1 Series
7274-2-.5
7274-2-1
7274-2-1.5
7274-2-2
7274-2-2.5
7274-2-3
7274-2-4
7274-2-5
7274-2-7.5
7274-2-10
7274-2-15
7274-2-20
7274-2 Series
7277-2-.5
7277-2-1
7277-2-1.5
7277-2-2
7277-2-2.5
7277-2-3
7277-2-4
7277-2-5
7277-2-7.5
7277-2-10
7277-2-15
7277-2-20
7277-2 Series
7274-11-.5
7274-11-.75
7274-11-1
7274-11-1.5
7274-11-2
7274-11-2.5
7274-11-3
7274-11-4
7274-11-5
7274-11-7.5
7274-11-10
7274-11-15
7274-11-20
7274-11 Series
KLIXON
W23X1A1G-1
W23X1A1G-2
W23X1A1G-3
W23X1A1G-4
W23X1A1G-5
W23X1A1G-7.5
W23X1A1G-10
W23X1A1G-15
W23X1A1G-20
W23X1A1G-25
W23X1A1G-30
W23X1A1G-35
W23X1A1G-40
W23X1A1G-50
W23-X1A1G Series
W58XC4C12A-1
W58XC4C12A-2
W58XC4C12A-3
W58XC4C12A-4
W58XC4C12A-5
W58XC4C12A-7
W58XC4C12A-10
W58XC4C12A-15
W58XC4C12A-20
W58XC4C12A-25
W58XC4C12A-30
W58XC4C12A-35
W58-XC4C12A Series
W31X2M1G-1
W31X2M1G-2
W31X2M1G-3
W31X2M1G-4
W31X2M1G-5
W31X2M1G-7.5
W31X2M1G-10
W31X2M1G-15
W31X2M1G-20
W31X2M1G-25
W31X2M1G-30
W31X2M1G-35
W31X2M1G-40
W31X2MIG-50
W31-X2M1G Series
POTTER BRUMFIELD
41-3K14LN2-60
41-3K14LN2-70A
41-3S14LN2-100
41-3 Series
E-T-A
High Amperage Circuit Breaker
SeenextpageforavailableOutlineDimensiondrawings...
PUSHBUTTONS AND TOGGLES
28. 16
1InstallationSupplies
AEROSPACE INSTRUMENT SUPPORT, INC.
Nite Lites
Part Number Current in mA
NL21414V 130 mA
NL21428V 50 mA
NL31814V 260 mA
NL31828V 98 mA
NL21414VALT 130 mA
NL21428VALT 50 mA
NL31814VALT 190 mA
NL31828VALT 75 mA
This product is approved and has met all PMA / FAA requirements. 2000 PMA number is PQ943SW.
For Blue-White bulbs add BW to end of part number.*
The Nite Lite product line has been approved to be installed on the following aircrafts:
AIS Recommends...
60 Watts
4.3A @ 14V
2.2A @ 28V
0-32 Volts
.40 lbs.
L 4.75” W 1.5” H1.25”
Recommended Circuit Breaker
5A @ 14V
7.5A @ 28V
Installation:
1. Mount dimmer module and rheostat
2. Route wiring harness and connect
mating connectors
3. Connect black wire to ground.
4. Connect red wire to circuit breaker.
5. Connect yellow wire to lights being dimmed.
6. Test dimmer system for proper operation.
DM-60 non-PMA’d Dimming Module
...for more dimming modules see the Inverters and Converters Section.
Also available in 5 volt*.
The New Piper Aircraft. Inc.
Comanche Series PA-24-400, PA-24-260, PA-24-250 and PA-24-180
Arrow Series PA28RT-201, PA28R-180, PA28R-200, and PA-24-201
Cherokee Series PA-32, and PA-32R
“J” Series PA-ll,PA-12,PA-14, and PA-16
Tri-Pacer PA-22
Warrior / Cadet PA-28-151, and PA-28-161
Dakota PA-28-236
Saratoga PA-32R
Navajo PA-31P, PA-31-350
Cheyene PA-42-l000, PA-42, PA-31T-500, and PA-31T-620
The Cessna Aircraft Company
140 Series
150 Series
170 Series
180 Series
Raytheon Aircraft Company / Beechcraft
Bonanza Series 33,F33,35,V35B,A36,A36TC, and B36TC
Debonair—95
Travel Air Series 55A, 55B, 55C, 55D, AND 55E
Baron 55 - 55E
Baron 58 - 58, 58TC, and 58P
Mooney Aircraft Corporation
Mooney Series M20, M20C, M20G, M20E, M2OF, 200S,
20K, 23L/M, and 252-TSE
Mooney Bravo M20M *5 Volt and Blue-White itterations are not PMA Approved
29. 17
1InstallationSupplies
• Flame retardatives
• Space-saving design
• Excellent voice clarity
• Built to the demanding specifications of aircraft manufacturers
• top performance under tough altitude and temperature conditions.
Quam Speakers
Part Number Size/Shape Depth Freq Response
Power
Capacity
Voice Coil
Impedance
Magnet
Material
Flame
Redardant?
30A05Z8 3” Square 1.281” 150-12 kHz 2W 8 Alnico V N
30C25Z8 3” Square 1.188” 150-14 kHz 5W 8 Ceramic N
35A05Z8 3”x5” Oval 1.500” 130-14 kHz 2W 8 Alnico V N
4C3Z8FR 4” Square 1.625” 200-12 kHz 5W 8 Ceramic Y
52C5FR 51/4” Round 2.000” 100-8 kHz 10W 3.2 Ceramic Y
SC Series
(Panel Mount)
Fig. 2
.31.03
.250
6.35
7/16
11.11
Length
*0.03 Projections Are Not 45
3/8
9.52
.03
15/32
11.90
15/16
33.3
Knurled Nut
11/8-24 UNS 2A Thread
28.57
1.125
28.57
1.220
30.98
Locking
Flats
Emits penetrating signal at min. current. Solid-state circuit -- no arcing -- no RF noise, no mechanical
wear, lowest failure rate with maximum efficiency. Compact, lightweight, versatile -- consumes less
current than normal indicator light. Ideal for use as safety device. Alerts to mechanical malfunctions
in cars, communications, computers, fire signals, medical electronics, etc. Sonalert signals may be
powered by many electrical sources ranging from single cell batteries to industrial power lines.
Little electrical power is required making them ideally suitable for portable battery operated equipment.
This low power feature allows the Sonalert signal to be turned on or off with a low power transistor,
SCR, or integrated circuit. Features a self-exterminating black nylon case.
Part Number Sound Freq. Tone Sound Level Oper. Volts Oper. Curr. Oper. Temp. Diameter Length Weight
SC628 2900 Hz Continuous 68-80 dB 6-28 DC 3-18 mA -20 C to +65 C 1.687 in 0.812 in 8 oz
SC628D 1900 Hz Continuous 60-75 dB 6-28 DC 6-23 mA -20 C to +65 C 1.687 in 0.812 in 8 oz
SC628P 2900 Hz Pulse/Fast 68-80 dB 6-28 DC 6-26 mA -20 C to +65 C 1.687 in 1.375 in 8 oz
SC628J 2900 Hz Pulse/Slow 68-80 dB 6-28 DC 6-26 mA -20 C to +65 C 1.687 in 1.375 in 8 oz
Sonalert Solid-State Audible Warning Device
Part Number Configuration
AIS-AUD5025 3” Square
AIS-AUD5030 4” Square
AIS-AUD5026 4” Round
AIS-AUD5040 4” Round DVC*
AIS-AUD5044 4” Square DVC*
AIS-AUD5027 5” Round
AIS-AUD5041 5” Round DVC*
AIS-AUD5032 5” Square
AIS-AUD5045 5” Square DVC*
AIS-AUD5028 5 ¼” Round
Part Number Configuration
AIS-AUD5042 5 ¼” Round DVC*
AIS-AUD5029 6 ½” Round
AIS-AUD5043 6 ½” Round DVC*
AIS-AUD5036 4”X6” Oval
AIS-AUD5049 4”X6” Oval DVC*
AIS-AUD5038 5”X7” Oval
AIS-AUD5051 5”X7” Oval DVC*
AIS-AUD5039 6”X9” Oval
AIS-AUD5052 6”X9” Oval DVC*
DVC = Dual Voice Coil
Avionics International Supply Speakers
SPEAKERS
30. 18
1InstallationSupplies
5225395-1 Male Dual Crimp BNC, RG58
225395-2 Male Dual Crimp BNC, RG59-62
225395-3 Male Dual Crimp BNC, RG55-223
5225395-6 Male Dual Crimp BNC, RG142-400
225395-7 Male Dual Crimp BNC, RG174-316,
225395-8 RG58 Plated Male RG179
225395-5 RG58 Plated Male RG141
31-320 BNC Male Crimp RG58
Mil Spec #M233293-01
31-320RFX BNC Male Crimp
RG58/142/400 Comm Grade
31-2RFX Male Solder Screw BNC, UG88
225397-1 Female Panel Jack BNC Dual Crimp, RG58
5225973-1 Right Angle Male Dual Crimp BNC, RG58,
Silver Finish
225974-1 Right Angle Male Dual Crimp BNC, RG58,
Nickel Finish
5225973-4 Right Angle Male Dual Crimp BNC, RG142, 400
225396-1 Female Dual Crimp BNC, RG58
225396-2 Female Dual Crimp BNC, RG59-62
225396-7 Female Dual Crimp BNC, RG174, RG316
2-331351-1 Silver Plated Female Dual Crimp BNC, RG58
PE4397 Female Dual Crimp, RG142, RG400
2-225395-1 Male Dual Crimp BNC, RG8-213
31-220NRFX Female to Female Bulkhead BNC, no seal
330024 Female to Female Bulkhead BNC,
silver w/rubber seal
BNC Connectors TNC Connectors
225550-2 Male Dual Crimp TNC, RG58
Silver Finish
225555-2 Male Dual Crimp TNC, RG58
Nickel Finish
5225555-6 Male Dual Crimp TNC, RG142, 400
Nickel Finish
225555-7 Male Dual Crimp TNC, RG8, 213
79075 TNC Right Angle Plug, Clamp
Solder for RG58
79125 TNC Right Angle Adapter
225551-2 Female Dual Crimp TNC, RG58
225551-6 Female Dual Crimp TNC, RG142
225559-2 Male Right Angle TNC,
Dual Crimp RG58
5225554-6 Male Right Angle TNC,
Dual Crimp RG142-400
225349-9 Male Right Angle TNC,
Dual Crimp RG9, 214
9-30-10 Tray Mount RF Connector
Tray Mount RF Connector
MS16624-1046 Snap Ring for 9-30-10 connector
GPS Notch filter from TED eliminates harmonic noise
interference with your GPS receiver.
P/N: 4-70-54
GPS Notch Filter
CONNECTORS AND ADAPTERS
31. 19
1InstallationSupplies
225532-1 Male Crimp SMA, RG58
225532-4 Male Srimp SMA, RG316, 174, 188
225532-3 Male Crimp SMA, RG142, 400
SMA UHF Connectors
226279-1 UHF Connector, RG58
BNC Adapters
221988-1 BNC Female T, Female to Female to Female
(Amphenol)
222320-1 BNC Female to UHF Male (AMP)
31-28RFX BNC Female to UHF Male (Amphenol)
31-217RFX BNC Male to N Female (Amphenol)
222321-1 BNC Female to N Male (AMP)
31-216RFX BNC Female to N Male (Amphenol)
221543-2 BNC Tee, Female to Male to Female (AMP)
31-208RFX BNC Tee, Female to Male to Female (Amphenol)
222165-2 BNC Male to Female Rt. Angle (AMP)
31-9RFX BNC Male to Female Rt. Angle (Amphenol)
221551-1 BNC Female to Female (AMP)
31-219 BNC Female to Female (Amphenol)
31-218RFX BNC Male to Male (Amphenol)
BNC Adapters (CONT’D)
31-221RFX BNC blukhead receptacle front mount,
solder cup terminal (Amphenol)
5228226-1 BNC bulkhead adapter Female to Female
with no rubber seal.
N Type Connectors
225392-2 N Male Dual Crimp Silver Body Plating
RG142, 400
5225699-1 Male Dual Crimp Nickle Body Plating
“N”RG142, 400
DBFTMA-90 BNC-TNC Right Angle for use with Eaton
and Mid-Continent WAAS Kits
CONNECTORS AND ADAPTERS
32. 20
1InstallationSupplies
324043 8G #10 Ring Terminal
324082 8G 1/4 Ring Terminal
324046 6G #10 Ring Terminal
324047 6G 1/4 Ring Terminal
324049 6G 3/8 Ring Terminal
“Terminal” Ring Terminals
320555 22-1 6 Knife Splice/Red
320566 16-1 4 Knife Splice/Blue
320620 1 2-1 0 Knife Splice/Yellow
“PIDG” Kinfe Splices
323994 26-22 Butt Splice/Gold
323975 24-20 Butt Splice/Clear
320559 22-16 Butt Splice/Red
320562 . 16-14 Butt Splice/Blue
320570 12-10 Butt Splice/Yellow
“PIDG” Butt Splices
320553 22-16 #4 Ring Terminal/Red
36152 22-16 #6 Ring Terminal/Red
320554 22-16 #8 Ring Terminal/Red
320551 22-16 #8 Ring Terminal/Red
36154 22-16 #10 Ring Terminal/Red
320571 22-161/4 Ring Terminal/Red
320572 22-16 5/1 6 Ring Terminal/Red
320573 22-16 3/8 Ring Terminal/Red
328996 16-14 #4 Ring Terminal/Blue
320619 16-14 #6 Ring Terminal/Blue
320565 16-14 #8 Ring Terminal/Blue
36160 16-14#10 Ring Terminal/Blue
321045 16-14 1/4 Ring Terminal/Blue
“PIDG” Ring Terminals
32996 8G #8 Ring Terminal
33460 8G #10 Ring Terminal
33461 8G 1/4 Ring Terminal
33462 8G 5/16 Ring Terminal
33463 8G 3/8 Ring Terminal
321298 6G #10 Ring Terminal
321598 6G 1/4 Ring Terminal
33466 6G 5/16 Ring Terminal
33467 6G 3/8 Ring Terminal
33469 4G 1/4 Ring Terminal
33470 4G 5/16 Ring Terminal
33471 4G 3/8 Ring Terminal
320383 2G 1/4 Ri ng Terminal nal
322870 2G 5/16 Ring Terminal
321600 2G 3/8 Ring Terminal
36918 1/0 7/16 Ring Terminal
36919 1/0 1/2 Ring Terminal
“Solistrand” Ring Terminals
and Splices
606289-1 4G 1/4 Ring Terminal
606290-2 2G 5/16 Ring Terminal
606290-5 2G 3/8 Ring Terminal
“Round Tongue” Terminals
324484 White
324485 Red
324486 Blue
324487 Yellow
Wire Caps
Pins
201298-1 Receptacle 14
200838-2 Receptacle 34
Pins
203540-1 Grounding Block 14
204814-1 Grounding Block 34
Grounding Blocks
P/N Length Under Head
201087-1 1.25 IN
203618-1 1.437 IN
Male Jack Screws
P/N AWG Finish
66105-1 24/20 Gold/Nickel
66105-4 24/20 Sel/Gold/Nickel
66101-1 18/16 Gold/Nickel
66101-4 18/16 Sel/Gold/Nickel
Sockets For Grounding
Block Receptacle
Metrimate Connectors
Pins Plug Width Height
4 207015-1 .799 .712
6 207152-1 .988 .712
9 207439-1 .988 .945
12 201017-1 1.181 .945
18 201422-1 1.594 .945
24 207304-1 1.594 1.114
36 207019-1 2.185 1.114
RCPT Width Height
207016-1 .799 .712
207153-1 .988 .712
207440-1 .988 .945
207018-1 1.181 .945
207443-1 1.594 .945
207305-1 1.594 1.114
207020-1 2.185 1.114
Strain Relief
N/A
207600-1
207601-1
207602-1
207603-1
207088-1
207604-1
Pins AWG
66103-1 24/20
66103-4 24/20
66099-1 18/16
66099-4 18/16
Sockets AWG
66105-1 24/20
66105-4 24/20
66101-1 18/16
66101-4 18/16
Finish
Gold/Nickel
Sel/Gold/Nickel
Gold/Nickel
Sel/Gold/Nickel
328998 16-14 5/16 Ring Terminal/Blue
328999 16-14 3/8 Ring Terminal/Blue
320634 12-10 #6 Ring Terminal/Yellow
320568 12-10#8 RingTerminal/Yellow
35109 12-10 #10 Ring Terminal/Yellow
320569 12-10 1/4 Ring Terminal/Yellow
320576 12-10 5/16 Ring Terminal/Yellow
320577 12-10 3/8 Ring Terminal/Yellow
323784 12-10 1/2 Ring Terminal/Yellow
CONNECTORS AND PINS
35. 23
1InstallationSupplies
Part Number Color Alt. Num Size
Plastic
M81969/14-01 Green/White 6500-048-22 22D
M81969/14-02 Red/White 294-108 20
M81969/14-03 Blue/White 8522-16 16
M81969/14-04 Yellow/ White 8522-1 12
M81969/14-06 Red 650-018-8 8
M81969/14-10 Red/Orange 6500-055-20 20
M81969/14-11 Red/White 6500-001-0020 20
M81969/16-02 Light Blue/ White 81515-16 16
M81969/39-01 Green/White 6500-045-20 20
M15570-22-1 Yellow/White ATD 1035 22
Metal
M81969/1-01 Green/White 91066-1 22
M81969/1-02 Red/White 91066-4 20
M81969/1-03 Blue/White 91066-3 16
M81969/1-04 Green/White 91067-1 12
Insertion Extraction Tools
Extraction Tools
P/N CL6860 - 14V
P/N CL2400 - 24V
Cigarette Lighter socket
P/N Q227-115
Snap in 115VAC Plug
AC/DC Recepticles
P/N Shell Size
206062-3 11
206966-7 13
206070-1 17
206138-8 23
Clamps
Flat pin extractor
P/N 11-03-0003
P/N 91285-1
Economical Model 91067-2 has long-lasting metal
tips for use with most rear-release RS-232 connec-
tors, wire sizes 20-24 AWG. One end of the tool is
used to insert contacts, and the other end is used to
extract contacts. Interchangeable tip Model 91285-1
is designed to insert and extract HD-22 and HD-20
contacts, wire sizes 22-28 AWG. Tool comes with
four insertion/extraction tips, hex wrench (to change
tips), and tip-locking plug.
Insertion/Extraction Tool
36. 24
1InstallationSupplies
U Type Nuts
Part Number Thread SIze
C8095-632-4 6-32
Black finish, Extended Reach
Instrument Clips/Snap Rings
Instrument Mounting Clips
MS Part Number NAS Part Number Leg Length Thread Size
MS33737-9C NAS487-13 .067” 6-32
MS33737-10C NAS487-14 .096” 6-32
MS33737-11C NAS487-15 1/8” 6-32
MS33737-12C NAS487-16 .187” 6-32
MS33737-13C NAS487-17 1/4” 6-32
MS33737-14C NAS487-18 .312” 6-32
MS33737-15C NAS487-20 3/8” 6-32
MS33737-16C NAS487-21 Universal 6-32
Snap Ring
MS Part Number
MS16624-1046
Nut Serts
Insert, Steel, Flush Mount, Open End, Knurled Nut Serts
Part Number Thread SIze
6-32 6-32
8-32 8-32
10-32 10-32
Rivnut (K=Keyed)
Part Number Mil Spac. P/N Thread Size
A6-75 MS27130-7 6-32 6-32
A6K-75 MS27130-A7K 6-32
A8-75 MS27130-8 8-32
A8K-75 MS27130-A8K 8-32
AN Part Number Thread Size
AN256-6 6-32
AN256-8 8-32
AN256-10 10-32
Nut Plate, Self locking, Two Lug, Floating, Low Height,
C’Bored, Reduced Rivet Spacing
Nut Plate, Self locking, Two Lug, Floating, Low Height
MS Part Number NAS Part Number Thread Size
MS21059-L04 NAS686-04 4-40
MS21059-L06 NAS686-06 6-32
MS21059-L08 NAS686-08 8-32
Nut Plate, Self locking, Two Lug, Low Height,
C’Bore, Reduced Rivet Spacing
NAS Part Number Thread Size
NAS697-A04 4-40
NAS697-A06 6-32
NAS697-A06L 6-32
NAS697-A08 8-32
NAS697-A3 10-32
Anchor Nuts
Nut Plate, Self locking, Two Lug, Low Height
MS Part Number Thread Size
MS21047-L06 6/32
MS21047-L08 8-32
MS21047-L3 10-32
Washers
Lock Washer, Carbon Steel, Cadmium Plated, (MS35338)
MS Number
MS35338-40
MS35338-41
MS35338-42
Screw Size
#4
#6
#8
MS Number
MS35338-43
MS35338-44
MS35338-45
Screw Size
#10
1/4
5/16
Flat Washer, Carbon Steel, Cadmium Plated, (AN960)
AN Number
AN960-4
AN960-6
AN960-8
AN960-10
Screw Size
#4
#6
#8
#10
AN Number
AN960-416
AN960-516
AN960-616
Screw Size
1/4
5/16
3/8
Lock Washer, Carbon Steel, Cadmium Plated, (MS35333)
MS Number
MS35333-36
MS35333-37
MS35333-38
MS35333-39
Screw Size
#4
#6
#8
#10
MS Number
MS35333-40
MS35333-41
MS35333-42
Screw Size
1/4
5/16
3/8
Flat Washer, Carbon Steel, Cadmium Plated, (AN970)
AN Number Screw Size
AN970-3 #10
AN970-4 1/4
AN970-5 5/16
AN970-6 3/8
Nuts
Nut, Self Locking Nylon Insert, Tall, 250° F,
Non-Corrosion Resistant Steel, (MS21044)
MS Number
MS32044N04
MS32044N06
MS32044N08
MS32044N3
Thread Size
4-40
6-32
8-32
10-32
MS Number
MS32044N4
MS32044N5
MS32044N6
Thread Size
1/4-28
5/16-24
3/8-24
Nut, Self Locking All Metal, 450’ F, Reduced
Hexagon, Reduced Height, Ring Base,
Non-Corrosion Resistant Steel, (MS21042)
MS Number
MS21042-04
MS21042-06
MS21042-08
MS21042-3
Thread Size
4-40
6-32
8-32
10-32
MS Number
MS21042-4
MS21042-5
MS21042-6
Thread Size
1/4-28
5/16-24
3/8-24
Nut, Self Locking All Metal, Tall, 550° F,
Non-Corrosion Resistant Steel, (AN363)
AN Number
AN363-632
AN363-832
AN363-1032
AN363-428
AN363-524
AN363-624
Alt. Part Number
MS21045-06
MS21045-8
MS21045-3
MS21045-4
MS21045-5
MS21045-6
Thread Size
6-32
8-32
10-32
1/4-28
5/16-24
3/8-24
Nut, Self Locking Nylon Insert, Short, 250° F,
Non-Corrosion Resistant Steel, (MS20364)
MS Number
MS20364-632
MS20364C-632
MS20364-832
MS20364C-832
MS20364-1032
MS20364C-1032
Alt. Part Number
MS21083C06
MS21083C08
MS21083C3
Thread Size
6-32
6-32
8-32
8-32
10-32
10-32
Nut, (Machined Steel) (MS35649 MS35650)
MS Number
MS35649-242
MS35649-262
MS35649-282
MS35650-302
Thread Size
4-40
6-32
8-32
10-32
MS Number
MS35650-3252
MS35650-3312
MS35650-3382
Thread Size
1/4-28
5/16-24
3/8-24
NUTS AND WASHERS
38. 26
1InstallationSupplies
Certi-Lok Crimping Tool
AMP Certi-Lok crimping tool with
interchangeable die sets. This is a
basic tool that uses interchangeable
snap-in die sets, which can be easily
inserted or removed. Die set P/N
169404 crimps AMP red / blue / yellow insulated
terminals and splices (22-10 AWG).
169400 AMP Certi-Lok Crimp Tool
169404 Die Set(Insulated 22-10 AWG)
169409 Die set (uninsulated 22-10 AWG)
169414 Die Set(22-12 gauge for pins sockets)
Positioners Dies
Sold Separately
AF8 has virtually limitless appli-
cation within the specified wire
range of 12 through 26 AWG. The
precision ratchet controls cycling
of the tool in both directions of
handle movement. This assures
the same accurate crimp every time. It’s like having a quality control
inspector at every work station. Positive crimp depth is controlled by an
8 position selector knob conveniently located on the tool frame. The AF8
measures 9 3/4” x 2 1/2” approximately and weighs 15 oz.
Upper Range Crimp Tool AF8
P/N M22520/1-01
Qualified to
MIL-DTL-22520/2, the DMC AFM8
is designed for most of the miniature
and sub-miniature connector types
that are so widely used in all types
of electronic systems. Wire sizes 20
through 32 AWG. Crimp depth is dialed on the 8 step selector knob by
merely raising the knob and rotating it to the proper position. The AFM8
is 5 3/4” in length and weighs approximately 10 oz.
Lower Range Crimp Tool AFM8
P/N M22520/2-01
Positioners Dies
Sold Separately
Dies Sold
Separately
P/N M22520/5-01 (HX4)
P/N M22520/1 0-01 (HX3)
The DMC HX4 and HX3 series
crimp tools feature a system
of interchangeable dies which
eliminate the need of separate
fixed die crimp tools for each and every different application. The HX4
is 11” in length and weighs approx. 21oz. The HX3 is 9” in length and
weighs approx. 11 oz.
HX3 HX4 Series Crimpers
The Daniels Battery Powered Crimper is
a long awaited answer to the need for an
economical, self-contained portable crimper
with ease of operation, and enough power to
make repeatable crimps on a wide range of
applications. The HDE37 fills that need, and
offers a solution where the volume of work exceeds the physical limits
of a worker with hand tools, and hoses and cables are unwelcome or
unsafe for the environment where the work is being performed.
Auto-Ctimper
P/N HDE37
Stripmaster Series
45-092 Stripmaster (8-30 AWG)
45-671 Stripmaster Lite (Economy Size, 12-30 AWG)
45-174 Stripmaster Custom (6-26 AWG)
L-5616 Replacement Frame Only
L-5617 Replacement Frame Only
L-5562 10-14 AWG Replacement Blade Die Set
L-5563 16-26 AWG Replacement Blade Die Set
L-5564 26-30 AWG Replacement Blade Die Set
Available in Standard, Lite (3/4 economy size),
and Custom configurations, the Stripmaster
series by Ideal Industries features a die cast
frame with knife-type blades for one step,
spring-aided stripping action. The Stripmast
Custom builds on this already impressive product
by adding Precision counter-bore die-type blades
(meets Mil-Spec) and a short stop latch which protects wire strands by
limiting the stripping stroke to 5/32” and retaining the slug until the wire is
ready for termination.
The Ideal 28-510 is a premier crimp tool
for 24-14 AWG open barrel contact com-
mercial type pins and sockets. The 28-512
is also a premier crimp tool for 30-18 AWG
open barrel D-sub RS232 pins and sockets.
28-510 Open Barrel Crimp Tool, 24-14 AWG
28-512 Open Barrel Crimp Tool, 30-18 AWG
Open Barrel Crimp Tool
Solid Barrel Crimp Tool
35-465 Solid Barrel Crimp Tool, 20-26 AWG
35-466 Solid Barrel Crimp Tool, 16-22 AWG
Industrial Crimp
The Ideal 50-2001 industrial crimp tool is
for 22-10 AWG insulated ring tongue ter-
minals and splices. Makes an ovalized
barrel crimp and support in one step. It
can be used on terminals by AMP, TB, 3M, Panduit and more. The dies
in this tool are color coded to gauge specifications.
51-0018 Industrial die set for 16-26 AWG miniature
insulated rings and splices
30-500 22-10 AWG Terminal Crimp Tool
30-572 Die Set 26-16 AWG, For Tool 30-500
T-Stripper Wire Stripper
• Precision form-ground knife blade
• Custom-cushioned grip
• Painted wire gauge markings
16-26 AWG P/N 45-121
CRIMPERS AND WIRE STRIPPERS
40. 28
1InstallationSupplies
KROY K5100 P/N: 2561000
Kroy’s introductes it’s newest addition,
the K5100 Handheld Label and Wire-
Marking Printer. This printer surpassess
the K2500, with such features as print
resolution of 300 dpi, auto sizing,
increased print speeds, internal battery
charger, downloadable fonts and
increased on-board memory. Additionally,
the K5100 uses the easy to load Kroy
Cartridge System allowing you to change
your media in seconds. Includes AC
Adapter.
Size: 11.0” L x 6.0” W x 4.0” H
Kroy’s New K4100 Desktop
Industrial Printer surpasses other
desktop printers with it’s built-in
flexibility and versatility. The K4100
features a print resolution of 300
dpi, auto sizing, fast print speeds,
scalable fonts, downloadable fonts
and on-board memory to store files
and fonts. Additionally, the K4100
uses the easy to load Kroy Cartridge
System allowing you to change your
media in seconds. Includes AC Adapter.
KROY K4100 P/N: 2562000
Size: 9.5” L x 8.0” W x 2.75” H
Color
Black on Blue
Black on Clear
Black on Gold
Black on Green
Black on Orange
Black on Red
Black on Silver
Black on White
Black on Yellow
Size
1” Tape
1
/2” Tape
8
/10” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
8
/10” Tape
1” Tape
1
/2” Tape
8
/10” Tape
1” Tape
P/N
2438635
2227501
2464401
2487901
2438701
2438601
2227526
2438626
2227539
2438639
2438648
2227535
2464435
2438631
227521
2438621
2227516
2464416
2487916
2438716
2438616
2227543
2464443
2487943
2438743
2438643
Color
Blue on Clear
Blue on White
Green on White
Red on Clear
Red on White
White on Black
White on Blue
White on Clear
White on Green
White on Orange
White on Red
Size
1
/2” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1” Tape
1
/2” Tape
1
/2” Tape
1” Tape
P/N
2227503
2227517
2438617
2227519
2438619
2227520
2227518
2438618
2227520
2487920
2438620
2227532
2438632
2227502
2438602
2227540
2438640
2227549
2227536
2438636
KROY Tapes
LABEL MAKERS
![II
Product data and information contained in this catalog have
been derived from information obtained from Avionics Inter-
national Supply, Inc. (AIS) suppliers. Some of this information
has been summarized and rearranged to facilitate search-
ing the catalog. While AIS attempts to verify the accuracy of
this catalog information, AIS does not assume responsibility
for errors or omissions. This catalogs information is subject
to change without notice, and AIS does not undertake any
obligation to provide updates.
The information contained in this catalog is intended for use
by persons possessing appropriate technical skill and knowl-
edge. Conditions of use of the items listed in the catalog are
beyond the knowledge or control of AIS. Consequently, AIS
assumes no liability whatsoever for results obtained or loss or
damage incurred as a result of the application of the informa-
tion presented. All users of this catalog do so at their own risk.
The catalog is neither a parts nor maintenance manual ap-
proved by the Federal Aviation Administration (FAA), and it
is not intended to replace the manuals provided by the AIS
suppliers. Users should independently verify the suitability
and legality of each product for its intended purpose before
the product is installed on an aircraft by means of an appro-
priate parts or maintenance manual, or other approved FAA
documentation.
AIS assumes no liability and makes no warranty with respect
to claims of patent, trademark or copyright infringement
or other similar claims which may arise out of or in connec-
tion with the use of any information or product listed in the
catalog.
AIS expressly disclaims all warranties, expressed or implied,
including but not limited to implied warranties of merchant-
ability and fitness for any particular purpose. In no event
shall AIS be liable for any injury, expenses, profits, loss or
damage, direct, indirect, incidental, consequential, special,
punitive or otherwise, arising out of the use or inability to use
any information or product described in this catalog.
Because some jurisdictions do not allow the exclusion or
limitation of liability for consequential or incidental damages,
the limitation in the paragraph immediately above may not
apply to you.
TERMS & CONDITIONS:
Avionics International supply, Inc. is a wholesale distributor
of avionics, installation supplies and support equipment. We
support avionics dealers and completion centers throughout
the world. We only sell to authorized dealers upon an AIS
approval. With this approval, you may purchase with terms
of COD or credit card. An open account of net 30 can be
achieved with verification of credit references and a signed
credit application. This signed application give AIS the right
to charge 1% interest per month on past due balances.
AIS WARRANTY & RETURNED MATERIALS POLICY:
GENERAL PROVISIONS:
Each returned part must have a Return Material Authorization
(RMA) number assigned to it by an AIS Customer Service Rep-
resentative before the return will be processed by Avionics In-
ternational Supply, Inc. (AIS). Returned parts must have been
originally purchased from AIS and must be in their original
packaging and properly packaged to prevent shipping and
handling damage.
AIS will return to the customer either new, repaired or re-
manufactured items or components that are warranted in ac-
cordance with the original Manufacturer’s warranty. Products
sold by AIS are warranted under the original manufacturer,
not AIS. Defective products returned will only be issued
credit upon the original manufacturer authorization and all
credits, if any, will be account credits against future purchases
from AIS.
RMA NUMBERS AND PROCESS:
AIS, at its option, may return, unprocessed, and at the send-
er’s expense, any item received without a valid RMA number.
To obtain the required RMA numbers, the Customer will
contact an AIS Customer Service Representative and provide
the AIS Customer Service Representative with the following
information:
1. Original AIS Sales Order or Invoice Number
2. Customer name or AIS Customer Account Number
3. Contact and call-back telephone number
4. Serial number and/or part number for each item to be
returned
5. Reason item is being returned
[Note: The AIS Customer Service Representative may need additional infor-
mation depending on the nature of the problem.]
Avionics International Supply, Inc. Catalog Disclaimer](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)