1. Safe bathing for people of all abilities
www.best-bath.com
"HG" ADA Shower Overview
4545 Enterprise, Boise, Idaho 83705
Tel: (208) 342-6823 / (800) 727-9907 - Fax: (208) 342-6832 / (800) 627-0929

2. Curb Details
Safe bathing for people of all abilities
www.best-bath.com
.5 Curb/bottom for transfer showers
1/2" Integral level support (adhered by others)
center line of drain hole 3/8"
FLOOR
drain cut-out size 8"x8" or 8" diameter 4"
vinyl flooring
.75 Curb/bottom for roll-in showers
ADA/Cal Title 24/TAS "Change of Level" allowed
1/2" (1: 2) change in level
1/2" Integral level support (adhered by others)
center line of drain hole 3/8"
1/4" flooring drain cut-out size 8"x8" or 8" diameter 4"
Page 1

3. Drain Details
Safe bathing for people of all abilities
www.best-bath.com
Cross Section of Standard, Cored Shower Bottom (installed)
3/16" Thick Fiberglass
Plywood Core
1/8" Thick Fiberglass
Build up or recess per code
3 " MIN.
4
6"
Cross Section of Low Profile Shower Bottom (installed)
1/4" Steel Flatbar
1/4" Thick Fiberglass
Integral Leveling Material
Build up or recess per code
Epoxy Adhesive (by installer)
3 " MIN.
4
8"
Page 2

4. Wall Section Detail
Safe bathing for people of all abilities
www.best-bath.com
Cut-away view
of HG unit wall
Gelcoat finish(color)
1/2" Plywood
Fiberglass laminate
Barrier coat
Fiberglass laminate
Page 3

5. Cross Section of HG Wall
Safe bathing for people of all abilities
www.best-bath.com
Top and Front
Nailing Flanges
1-1/8" Overall Wall Thickness
Inside Wall Surface
1/2" Plywood
5/8" Space
Face of Stud
Page 4

6. Laminate Schedules
Safe bathing for people of all abilities of HG Showers
www.best-bath.com
Laminate Schedule - Walls Laminate Schedule - Cored Bottoms Material Cut List
- Gel Coat 18 mil - Gel Coat 18 mil Walls
- Barrier Coat 30 mil - Barrier Coat 30 mil as required 1/2" Plywood 4" x 8"
- Hydrate (bed) 90 mil (3/32") - Hydrate (bed) 130 mil (1/8") " 8" x 8"
" 2" x 8"
- Plywood Core 1/2" - Plywood Core 3/4"
" 2" x 12"
- Hydrate (top) 130 mil (1/8") - Hydrate (top) 130 mil (1/8") as required 3" x 5" HD cards
- Level Block(s)
corner reinforcements Material Cut List
(not on smooth wall models) Bottom
same on this side
Full as required 3/4" Plywood
Plyw
ood
Cored bottom
Full
Plyw One Piece Shower HG/CG
ood (Hospital Grade/ Commercial Grade)
with 15 (1.5") or HIGHER curb
One Piece Tub/shower HG
(Hospital Grade/ Commercial Grade)
Laminate Schedule - Walls Laminate Schedule - Uncored Bottoms Material Cut List
- Gel Coat 18 mil - Gel Coat 18 mil Walls
- Barrier Coat 30 mil - Barrier Coat 30 mil as required 1/2" Plywood 4" x 8"
- Hydrate (bed) 90 mil (3/32") - Hydrate (bed) 130 mil (1/8") " 8" x 8"
" 2" x 8"
- Plywood Core 1/2" - Steel Flat Bar 1 length at curb
" 2" x 12"
- Hydrate (top) 130 mil (1/8") - Hydrate (top) 130 mil (1/8") as required 3" x 5" HD cards
- Level Block(s)
- Integral Leveling Support Material Cut List
corner reinforcements
(not on smooth wall models)
Bottom
same on this side Steel Flat Bar 1/4" x 1-1/4" x XX"
Full
Plyw
ood
1/4" FRP Laminate and
Integral Leveling Support
(7 # Urethane Compound)
Full
Plyw
ood
Steel Flat Bar
One Piece Shower HG/CG
(Hospital Grade/ Commercial Grade)
with 12 (1.25") or LOWER curb
Page 5

7. Water Containment Solutions
Safe bathing for people of all abilities
www.best-bath.com
"The solution to wet floors"
Specifications for The WaterStopper Kit
- Material: EPDM Rubber, 50 Durometer, Endcaps: injection molded Vyram rubber Kit Contents:
- Finish: Kits are available in both Grey and Beige - 1 ea. Specified length of WaterStopper
- Dimensions: Will fit on any Access ADA or Barrier Free model offered - 2 ea. Specified size end caps
- Available for other Brands. - 2 ea. Alcohol wipes
- Installation: Self-Adhesive. - Installation Instructions
Tape-weighted curtain Tape-weighted curtain
without WaterStopper with WaterStopper
Front view Front view
13 8"
114"
Endcap 2-1/4" radius Endcap 3/8" radius 3
Cross Section 16" Flattens under wheelchair
Specifications for The Semi-permanent Threshold Adaptor
- Material: Powder coated aluminum, .100" thick. Kit Contents:
- Finish: Color WHITE, special colors available for quantity orders. - 1 ea. Specified TAS (cut to fit)
- Dimensions: Made to fit any ADA or Barrier Free model offered by Best Bath Systems. - 1 ea. Cartridge of silicone caulk (white)
- Available for other brands (cut to fit on-site). - Installation Instructions
- Installation: Simple, removable installation with silicone caulk.
Silicone Silicone Shower Bottom
Bathroom Floor
TAS odel
er m ini)
cut to fit p TAS-M (M odel
fit per m
cut to
2-1/2" 2"
2-3/8"
3-1/2"
Page 6

8. Flange Trim Kit FTK-R-5-125
Safe bathing for people of all abilities
www.best-bath.com
Application
For use as an easy way of covering the nailing flange where there already is drywall or other wall material BEHIND
the shower or tubshower.
Installation
Measure the distance between the drywall at the back wall.
Trim or sand the molding sections to size with a hacksaw. Kit consists of
Cut the Butyl tape in 2" pieces, fold double as needed 1 ea Backwall section
and stick to the nailing flange and drywall at 8" intervals. 1 ea Left front and top section
Press the molding in place. 1 ea Right front and top section
Repeat with the rest of the sections. 10 ft. 5/16" Butyl tape 3M #8621
Caulk all around the edges. 5/16" thick, 1/2" wide
R 1/8" 1 ea Silicone (white)
Material 1-1/4"
Matching gelcoat fiberglass
Install with butyl tape and caulk 1/2"
1/16"
Cross Section of Molding
stud
Silicone caulk
Butyl Tape #8621
Flange Trim Moulding Drywall
Screw head
Shower Nailing Flange
stud Butyl tape
Latex caulk (paintable)
Drywall
8"
Cross Section of Molding installed
Moldings shown
before installation
Page 7

9. One Hour Fire Rated
Safe bathing for people of all abilities Drywall Stud Pocket
www.best-bath.com
Nailing Flange
PLAN
1st Drywall 2nd Drywall
Studs
2nd Drywall Nailing Flange
1st Drywall
Shower Wall
DETAIL A iso view at
top of wall (installed)
2nd Drywall
Page 8

10. 90° Reveal and Conventional
Safe bathing for people of all abilities Flange Details
www.best-bath.com
PLAN
DETAIL A DETAIL B
Stud 1"
Studs
1"
5/8" Drywall 5/8" Drywall
2"
DETAIL A DETAIL B Drywall
5/8" drywall Nailing Flange
"Reveal 90" Feature Conventional
Studs
stud
DETAIL B
top of wall
DETAIL A iso view at (installed)
top of wall (installed)
Page 9 Drywall

11. LPB1
Safe bathing for people of all abilities
www.best-bath.com
Storage: Do not Rest on Unscrew this block
before installing
the Bottom Once the Drain
Fitting is Installed
8"x 8" or
8" diam.
NOTE: The drain cut-out must be
Epoxy
8" diam. or 8" x 8" and back filled
if it is larger to prevent flexing.
Brace or weigh down the 2x4s
so that they are tight all along
Epoxy the shower floor.
3/4" high
Epoxy Adhesive:
3/4" dollops every 8" min.
Do not walk on bottom
until epoxy has set up
TIP: Also put epoxy between 2 pcs.
of scrap wood to monitor cure.
Use straight 2x4s
PLAN for 38" x 38" showers only A
Use straight 2x4s A=approx. 6"
Use straight 2x4s A Screw through
flanges every 8"
PLAN for Rear Drain Showers
SEE PAGE 11 FOR ADDITIONAL
IMPORTANT INSTRUCTIONS
PLAN for Showers Larger than 38" x 38" Page 10

12. Showers (1-piece) with
Safe bathing for people of all abilities Low Profile Bottoms
www.best-bath.com
The extremely low profile of this shower bottom may eliminate the need for recessing.
In order to get full, permanent contact with the floor, it MUST be installed per these instructions.
Failure to follow these instructions may result in failure not covered by warranty.
LPB1
1/4" thick fiberglass drain fitting (do not store the pan
factory leveling material upright resting on the drain)
Epoxy adhesive (8" o.c., see over)
C
L 3/4" min.
unscrew before
installation
Epoxy adhesive
8"
NOTE: The drain cut-out must be 8"
CROSS SECTION OF BOTTOM diam. or 8" x 8". If it is larger, back-fill
(installed) to prevent flexing.
Installation:
1. Check the stud pocket for level and correct 9. Put the unit face-down in front of the pocket.
dimensions and the drain hole in the floor 10. Apply the epoxy adhesive to the floor.
for the correct distance to the studs. (See illustration on the front page)
The floor must be level +/- 1/8 inch. At the same time, glue some scrap wood
2. The shower drain must be centered in an 8" together as a cure time sample for later on.
cut-out in the floor (refer to specification or 11. Tip the shower into position, making sure it
the actual shower). See drawing above. is positioned at the line drawn in step 8.
3. Have the plumber install the drain fitting. Avoid stepping on the bottom until the
DO NOT store the unit resting on the drain. epoxy has set up.
4. Prepare the drain pipe to receive the drain. 12. When level, screw through the flanges.
5. Clean the floor and the pan's underside. 13. Use 2x4 boards to brace or weigh down as
The floor may be damp but no standing water. shown over until snug to the shower floor.
6. The leveling material has been scuffed up 14. Make sure the bottom has adequate drain-
at the factory. Clean off any debris stuck to it. slope by pouring water in it or with a level.
7. Remove the plywood strip that is screwed 15. Check the cure time sample from step #10
to the leveling block at the back. and when fully bonded, remove the bracing
8. Draw a line where the curb will be. boards or after no less than 2 hrs.
(more if the floor is cold)
Page 11

13. OPTION VERIFICATION MODEL: LCS26337A75BHG - LEFT PLBG "ACCESSIBLE" QTY:
63"
311 2"
1
201 2"
ADA COMPLIANT
381 2 "
36"
A
A 1" 4
3
TOP VIEW PERSPECTIVE - N.T.S.
2
2" 1"
60"
2 27"
21"
7
27"
5 8 8
783 4 "
75"
60"
CENTERED CENTERED
6
46"
11 2 "
40"
5
37"
34"
18"
18"
INT. LEFT ELEVATION 3 " FRONT ELEVATION 3 " INT. RIGHT ELEVATION
4 8
SCALE DATE
E --- --- PROJECT: DB: MA 1/2" = 1'-0"
DRAWING NUMBER
D --- --- COMPANY: CB: PVR SHEET 1 OF 2
C --- ---
NOTES: ACCEPTED AS CORRECT BY:
B --- --- Rough-in stud opening +1/4” -0” nominal dimensions
All vertical accessory dimensions are measured from the floor of the shower.
A --- --- Best Bath Systems, Inc. retains ownership of all product designs and any
REV CHANGE DATE DIV. OF FIBERGLASS SYSTEMS NC.
www.best-bath com 1-800-727-9907
proprietary information may not be disclosed to its competitors, their agents
or affiliates.
X / /

14. OPTION VERIFICATION MODEL:
10
PERSPECTIVE - N.T.S. LAMINATE DETAIL C - SCALE: 3" = 1'-0"
3
SECTION A-A - SCALE: 3" = 1'-0"
UNIT WEIGHT: NOTES:
23 - - -
22 - - -
21 - - -
20 - - -
19 - - -
18 - - -
17 - - -
16 - - -
15 - - -
14 - - -
13 - - -
12 - - -
11 - - -
1
10 - FULL 2" PLYWOOD BACKING - -
9 1 CORRUGATED PROTECTIVE PAD - -
1
8 1 32" x 36" x 1- 4" L GRAB BAR - -
7 1 SYMMONS S-96-300-B30-L-X-V, VALVE AND GLIDE BAR KIT - -
6 1 34" x 21" FOLD DOWN SEAT WITH SWING DOWN LEGS, PHENOLIC - -
5 2 SURFACE MOUNT SOAP DISH - -
4 1 NO CAULK BRASS DRAIN WITH POLISHED STAINLESS STEEL SCREEN - -
3 1 T-SHAPED RUBBER WATER STOPPER KIT GREY KTWSG5L
2 1 AQA MOUNTING BRACKET SET - -
1 1 CURTAIN ROD - -
KEY QTY. DESCRIPTION COLOR PART NUMBER MARK
FACTORY INSTALLED LOCATION PRE-DRILL
BY
INSTALLED OTHERS HOLES
PARTS LIST ONLY
DATE
PROJECT:
DRAWING NUMBER
COMPANY:
DIV. OF FIBERGLASS SYSTEMS NC.
www.best-bath com 1-800-727-9907 REFER TO SHEET 1 OF 2 FOR ACCESSORY LOCATIONS SHEET 2 OF 2

15. Product Guide Specification LCS26337A75BHG Accessible
Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) Three-Part
Section Format and Page Format, contained in the CSI Manual of Practice. The section must be carefully reviewed and edited by the
Architect to meet the requirements of the project and local building code. Coordinate with other specification sections and the
drawings. Delete all "Specifier Notes" when editing this section.
SECTION 15410
A.D.A. COMPLIANT BATHING UNITS
Specifier Notes: This section covers Best Bath Systems A.D.A. Compliant showers of composite fiberglass-reinforced construction.
Consult Fiberglass Systems for assistance in editing this section for specific applications.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. ADA Compliant, one-piece fiberglass showers.
1.2 RELATED SECTIONS
A. Section 15400 – Building services: Piping.
1.3 REFERENCES
A. ASTM E 162 - Surface Flammability of Materials Using a Radiant Heat Energy Source.
B. NFPA 258 - Determining Smoke Generation of Solid Materials.
1.4 SUBMITTALS
A. Comply with requirements of Section 01300 - Submittals.
B. Product Data: Submit manufacturer's product data, including composite fiberglass material description, construction details,
dimensions, accessories, fixtures, and finishes.
C. Samples: Submit one 6 inch square sample of composite fiberglass material in each color specified for Architect's approval.
1.5 QUALITY ASSURANCE
A. Codes and Standards: Comply with the following codes and standards.
1. ADA Accessibility Guidelines for roll-in showers.
2. ANSI Z124.2 - Plastic Shower Receptors and Shower Stalls.
3. ANSI A117.1 Accessible and Useable Buildings and Facilities
4. ASTM F 462 - Consumer Safety Specification for Slip-Resistant Bathing Facilities.
5. IAMPO/UPC – Uniform Plumbing Code.
6. California Building Code, Chapter 11B Accessibility to Public Buildings, Public Accommodations, Commercial Buildings
and Publicly Funded Housing.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Delivery: Deliver bathing units to site in manufacturer's original, unopened containers and packaging, with labels clearly
indicating manufacturer and model number.
B. Storage: Store bathing units indoors in an area protected from damage and in accordance with manufacturer's instructions.
C. Handling: Protect bathing units during handling and installation to prevent damage.
1.7 WARRANTY
A. Provide manufacturer's limited warranty against structural and finish defects for 3 years from date of installation.
LCS26337A75BHG Accessible 1 of 3

16. PART 2 PRODUCTS
2.1 MANUFACTURER
A. Best Bath Systems, 4545 Enterprise Street, Boise, Idaho 83705, Phone 800-727-9907, Fax 800-627-0929.
2.2 A.D.A. COMPLIANT BATHING UNITS
One piece fiberglass shower stall, meeting A.D.A. and CA. accessibility code criteria.
2.3 MATERIALS
A. Gelcoat Finish:
Sanitary ware grade gelcoat. Minimum cured thickness 0.015 inch.
Barrier Coat: Ceramic fiber filled polyester resin coating to enhance gloss and surface hardness.
B. Skin Layer: Glass fiber and polyester resin layer to provide resilient skin against the gelcoat finish.
C. Filled and Cored Layer: Fiberglass laminate with minimum 15 percent fiberglass content and filled resin completely
encapsulating a 1/2 inch plywood core on most flat surfaces, to provide stiffness as well as backing for grab bar and seat
anchoring.
All core termination edges beveled.
Floor of ¼ inch thick fiberglass laminate with an integral level support compound bonded to it.
1. Flame Spread Rating: Less than 75 in accordance with ASTM E 162.
2. Smoke Generation: Less than 450 in accordance with NFPA 258.
Specifier note: Select plumbing hand.
Model LCS26337A75BHG. “Accessible”
The unit measures 63 inches wide x 37-1/2 inches deep x 78-3/4 inches high. [Right][Left] hand plumbing.
B. Color: Best Bath White
2.5 ACCESSORIES
Specifier Notes: Consult Best Bath Systems for assistance in specifying accessories for specific applications. Coordinate right and left
hand accessories with bathing unit models.
Select brand of mixing valve and delete the other.
A. Mixing Valve: [Symmons S-96-300-B30-L-X-V] Brass, pressure balanced, lever handle valve, plumbing elbow, polished
chrome finish. Hand held shower with applicable hose. Vertically mounted, 30 inch long glide bar, polished chrome finish
and cradle with adjustable height setting for hand held shower.
B. Soap Dish: Two (2) white cast polyester surface mounted soap dishes, one (1) each at the sitting level and the standing level.
C. Folding seat: 34” x 21”, White phenolic slat seat surface, stainless steel frame and swing down legs.
D. Grab Bar 32” x 36” corner type, 1-1/4 inch diameter, stainless steel, 18 gauge.
E. Shower Curtain Rod: 65 inches, stainless steel, 20 gauge, 1 inch OD, with mounting flanges.
F. Drain: No-Caulk, brass body with polished stainless steel screen.
G. Water Stopper kit, collapsible 60 inch grey “T” shaped retainer with large radius end caps.
H. Corrugated cardboard interior bottom protector.
I. Shower system individually palletized, faced at the opening with corrugated protector and stretch wrapped.
LCS26337A75BHG Accessible 2 of 3

17. PART 3 EXECUTION
3.1 EXAMINATION
A. Inspect areas where ADA compliant bathing units will be installed. Notify the Architect of conditions that would adversely
affect the installation or subsequent utilization of bathing units. Do not proceed with installation until unsatisfactory
conditions are corrected.
3.2 INSTALLATION
A. Install in accordance with manufacturer's instructions which are different from those of conventional one piece shower units
in that the unit may be installed directly on top of the flooring and still meet the A.D.A. 1/2 inch maximum curb height
requirement. To allow for this the following needs to be done:
1. The hole around the drain needs to be 8 inch diameter.
2. The unit needs to be adhered to the floor using an epoxy adhesive that is provided by the shower manufacturer.
3. Flooring needs to be brought up to the bevel on the curb.
B. Install barrier free bathing units level, plumb, and square with flat wall surfaces.
C. Touch-up minor damaged surfaces caused during installation. Replace damaged components as directed by Architect.
3.3 ADJUSTING
A. Test and adjust mixing valves and hand held showers for proper and efficient operation, including water temperature,
pressure, and volume.
3.4 CLEANING
A. Clean surfaces in accordance with manufacturer's instructions.
B. Do not use abrasive cleaners, metal scrapers, or wire brushes.
3.5 SCHEDULE
Specifier Notes: Provide a schedule if two or more ADA compliant bathing units are specified with different model numbers or
accessories. Identify each unit separately. Coordinate schedule with location of units indicated on drawings. This is an optional
location for the schedule, rather than on the drawings.
END OF SECTION
APPROVED
ARCHITECT: NAME: TITLE: DATE:
ENGINEER: NAME: TITLE: DATE:
OWNER: NAME: TITLE: DATE:
LCS26337A75BHG Accessible 3 of 3

18. OPTION VERIFICATION MODEL: LCS26337A75BHG - LEFT PLBG "ADAPTABLE" QTY:
63"
311 2"
1
201 2"
ADA COMPLIANT
381 2 "
36"
A
A 1" 4
3
TOP VIEW PERSPECTIVE - N.T.S.
2
2" 1"
60"
2 27"
21"
6
27"
5 7 7
783 4 "
75"
60"
CENTERED CENTERED
46"
40"
5
37"
34"
18"
INT. LEFT ELEVATION 3 " FRONT ELEVATION 3 " INT. RIGHT ELEVATION
4 8
SCALE DATE
E --- --- PROJECT: DB: MA 1/2" = 1'-0"
DRAWING NUMBER
D --- --- COMPANY: CB: PVR SHEET 1 OF 2
C --- ---
NOTES: ACCEPTED AS CORRECT BY:
B --- --- Rough-in stud opening +1/4” -0” nominal dimensions
All vertical accessory dimensions are measured from the floor of the shower.
A --- --- Best Bath Systems, Inc. retains ownership of all product designs and any
REV CHANGE DATE DIV. OF FIBERGLASS SYSTEMS NC.
www.best-bath com 1-800-727-9907
proprietary information may not be disclosed to its competitors, their agents
or affiliates.
X / /

19. OPTION VERIFICATION MODEL:
9
PERSPECTIVE - N.T.S. LAMINATE DETAIL C - SCALE: 3" = 1'-0"
3
SECTION A-A - SCALE: 3" = 1'-0"
UNIT WEIGHT: NOTES:
23 - - -
22 - - -
21 - - -
20 - - -
19 - - -
18 - - -
17 - - -
16 - - -
15 - - -
14 - - -
13 - - -
12 - - -
11 - - -
10 - - -
9 - FULL 1" PLYWOOD BACKING
2 - -
8 1 CORRUGATED PROTECTIVE PAD - -
1
7 1 32" x 36" x 1- 4" L GRAB BAR - -
6 1 SYMMONS S-96-300-B30-L-X-V, VALVE AND GLIDE BAR KIT - -
5 2 SURFACE MOUNT SOAP DISH - -
4 1 NO CAULK BRASS DRAIN WITH POLISHED STAINLESS STEEL SCREEN - -
3 1 T-SHAPED RUBBER WATER STOPPER KIT GREY KTWSG5L
2 1 AQA MOUNTING BRACKET SET - -
1 1 CURTAIN ROD - -
KEY QTY. DESCRIPTION COLOR PART NUMBER MARK
FACTORY INSTALLED LOCATION PRE-DRILL
BY
INSTALLED OTHERS HOLES
PARTS LIST ONLY
DATE
PROJECT:
DRAWING NUMBER
COMPANY:
DIV. OF FIBERGLASS SYSTEMS NC.
www.best-bath com 1-800-727-9907 REFER TO SHEET 1 OF 2 FOR ACCESSORY LOCATIONS SHEET 2 OF 2

20. 34" x 21" Folding Seat
Safe bathing for people of all abilities Phenolic Slat with Legs
www.best-bath.com
34" Specifications:
-FOLDING SHOWER SEAT WITH SWING
DOWN LEGS
-PHENOLIC SLATS
-SIZE: 34" X 21" L-SHAPE
201 2 "
131 2 "
18"
Operation:
Seat is automatically held in a raised position by a phenolic cross member attached to the front and rear support legs. When the
seat is lowered into its down position, the swing down leg automatically aligns the front and rear support legs with the help of
the phenolic cross members.
Architectural Specifications:
Shower seat with swing down legs. The swing down legs automatically level when the seat is lowered to a horizontal sitting
position. the seat automatically locks itself when swung into its "up" position with the use of the phenolic cross members.
Materials:
FRAME: Type 304 (18-8) S.S. tubing, 1 1/4" (32mm) x 18 ga. (1.2mm) square main frame with 1" (25mm) x 18 ga. (1.2mm) round
cross members.
WALL FLANGES: Type 304 (18-8) S.S. 10 ga. (3.4mm) x 3" (76mm) diameter, heliarc welded to 1" (25mm) supports, and to 1 1/4"
(32mm) round x 12 ga. (2.7mm) frame hinge couplings. Three mounting holes per flange.
SWING DOWN LEGS: "H" shaped yoke of Type 304 (18-8) S.S. 1" diameter x 18 ga. round tubing, heliarc welded to 1 1/4" (32mm)
round x 12 ga. (2.7mm) frame hinge couplings.
SEAT CHOICE: Phenolic Slat, 1/2" (13mm) x 3" (78mm) bolted to frame with stainless steel screws and nuts.
INSTALLATION: All shower seats must only be installed using sufficient in-wall backing material.
Page 19

21. Product Guide Specification LCS26337A75BHG Adaptable
Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) Three-Part
Section Format and Page Format, contained in the CSI Manual of Practice. The section must be carefully reviewed and edited by the
Architect to meet the requirements of the project and local building code. Coordinate with other specification sections and the
drawings. Delete all "Specifier Notes" when editing this section.
SECTION 15410
A.D.A. COMPLIANT BATHING UNITS
Specifier Notes: This section covers Best Bath Systems A.D.A. Compliant showers of composite fiberglass-reinforced construction.
Consult Fiberglass Systems for assistance in editing this section for specific applications.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. ADA Compliant, one-piece fiberglass showers.
1.2 RELATED SECTIONS
A. Section 15400 – Building services: Piping.
1.3 REFERENCES
A. ASTM E 162 - Surface Flammability of Materials Using a Radiant Heat Energy Source.
B. NFPA 258 - Determining Smoke Generation of Solid Materials.
1.4 SUBMITTALS
A. Comply with requirements of Section 01300 - Submittals.
B. Product Data: Submit manufacturer's product data, including composite fiberglass material description, construction details,
dimensions, accessories, fixtures, and finishes.
C. Samples: Submit one 6 inch square sample of composite fiberglass material in each color specified for Architect's approval.
1.5 QUALITY ASSURANCE
A. Codes and Standards: Comply with the following codes and standards.
1. ADA Accessibility Guidelines for roll-in showers.
2. ANSI Z124.2 - Plastic Shower Receptors and Shower Stalls.
3. ANSI A117.1 Accessible and Useable Buildings and Facilities
4. ASTM F 462 - Consumer Safety Specification for Slip-Resistant Bathing Facilities.
5. IAMPO/UPC – Uniform Plumbing Code.
6. California Building Code, Chapter 11B Accessibility to Public Buildings, Public Accommodations, Commercial Buildings
and Publicly Funded Housing.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Delivery: Deliver bathing units to site in manufacturer's original, unopened containers and packaging, with labels clearly
indicating manufacturer and model number.
B. Storage: Store bathing units indoors in an area protected from damage and in accordance with manufacturer's instructions.
C. Handling: Protect bathing units during handling and installation to prevent damage.
1.7 WARRANTY
A. Provide manufacturer's limited warranty against structural and finish defects for 3 years from date of installation.
LCS26337A75BHG Adaptable 1 of 3

22. PART 2 PRODUCTS
2.1 MANUFACTURER
A. Best Bath Systems, 4545 Enterprise Street, Boise, Idaho 83705, Phone 800-727-9907, Fax 800-627-0929.
2.2 A.D.A. COMPLIANT BATHING UNITS
One piece fiberglass shower stall, meeting A.D.A. and CA. accessibility code criteria.
2.3 MATERIALS
A. Gelcoat Finish:
Sanitary ware grade gelcoat. Minimum cured thickness 0.015 inch.
Barrier Coat: Ceramic fiber filled polyester resin coating to enhance gloss and surface hardness.
B. Skin Layer: Glass fiber and polyester resin layer to provide resilient skin against the gelcoat finish.
C. Filled and Cored Layer: Fiberglass laminate with minimum 15 percent fiberglass content and filled resin completely
encapsulating a 1/2 inch plywood core on most flat surfaces, to provide stiffness as well as backing for grab bar and seat
anchoring.
All core termination edges beveled.
Floor of ¼ inch thick fiberglass laminate with an integral level support compound bonded to it.
1. Flame Spread Rating: Less than 75 in accordance with ASTM E 162.
2. Smoke Generation: Less than 450 in accordance with NFPA 258.
Specifier note: Select plumbing hand.
Model LCS26337A75BHG. “Adaptable”
The unit measures 63 inches wide x 37-1/2 inches deep x 78-3/4 inches high. [Right][Left] hand plumbing.
B. Color: Best Bath White
2.5 ACCESSORIES
Specifier Notes: Consult Best Bath Systems for assistance in specifying accessories for specific applications. Coordinate right and left
hand accessories with bathing unit models.
Select brand of mixing valve and delete the other.
A. Mixing Valve: [Symmons S-96-300-B30-L-X-V] Brass, pressure balanced, lever handle valve, plumbing elbow, polished
chrome finish. Hand held shower with applicable hose. Vertically mounted, 30 inch long glide bar, polished chrome finish
and cradle with adjustable height setting for hand held shower.
B. Soap Dish: Two (2) white cast polyester surface mounted soap dishes, one (1) each at the sitting level and the standing level.
C. Grab Bar 32” x 36” corner type, 1-1/4 inch diameter, stainless steel, 18 gauge.
D. Shower Curtain Rod: 65 inches, stainless steel, 20 gauge, 1 inch OD, with mounting flanges.
E. Drain: No-Caulk, brass body with polished stainless steel screen.
F. Water Stopper kit, collapsible 60 inch grey “T” shaped retainer with large radius end caps.
G. Corrugated cardboard interior bottom protector.
H. Shower system individually palletized, faced at the opening with corrugated protector and stretch wrapped.
LCS26337A75BHG Adaptable 2 of 3

23. PART 3 EXECUTION
3.1 EXAMINATION
A. Inspect areas where ADA compliant bathing units will be installed. Notify the Architect of conditions that would adversely
affect the installation or subsequent utilization of bathing units. Do not proceed with installation until unsatisfactory
conditions are corrected.
3.2 INSTALLATION
A. Install in accordance with manufacturer's instructions which are different from those of conventional one piece shower units
in that the unit may be installed directly on top of the flooring and still meet the A.D.A. 1/2 inch maximum curb height
requirement. To allow for this the following needs to be done:
1. The hole around the drain needs to be 8 inch diameter.
2. The unit needs to be adhered to the floor using an epoxy adhesive that is provided by the shower manufacturer.
3. Flooring needs to be brought up to the bevel on the curb.
B. Install barrier free bathing units level, plumb, and square with flat wall surfaces.
C. Touch-up minor damaged surfaces caused during installation. Replace damaged components as directed by Architect.
3.3 ADJUSTING
A. Test and adjust mixing valves and hand held showers for proper and efficient operation, including water temperature,
pressure, and volume.
3.4 CLEANING
A. Clean surfaces in accordance with manufacturer's instructions.
B. Do not use abrasive cleaners, metal scrapers, or wire brushes.
3.5 SCHEDULE
Specifier Notes: Provide a schedule if two or more ADA compliant bathing units are specified with different model numbers or
accessories. Identify each unit separately. Coordinate schedule with location of units indicated on drawings. This is an optional
location for the schedule, rather than on the drawings.
END OF SECTION
APPROVED
ARCHITECT: NAME: TITLE: DATE:
ENGINEER: NAME: TITLE: DATE:
OWNER: NAME: TITLE: DATE:
LCS26337A75BHG Adaptable 3 of 3