9. FSD306
Furniture Spice Drawer
FWC630
Furniture Wine Cube
OGP8
U309024-ROT-4
4 roll out trays
FWC630 and FSD306
are only 12" deep and will line up
with the face of the rest of the cabinets
without having to modify anything
DA
10. Glass is NOT included
and will need to be purchased
through a local glass supplier.
This is often less expensive
than cabinet companies are
able to provide glasss for.
In many cases, when homeowners decide to do a
seperate cooktop and oven they will end up doing a
decorative hood option. you have the perfect setup
to create a nice focal point with the decorative hood
and decorative Backsplashes.
11. You have enough space that you
wouldn't necessarily need to do anything
odd with the Island if you didn't want to.
The materials being provided to creat the
supports/ Box columns are up to you to configure on site.
so you can make that call..
12.
13.
14.
15.
16. There will be a wall built up to this height behind this cabinet
I'd build the pet bowl control into this awkward space.
It's also away from where the people eat.
17. 24" | 27"
34½"
23½" | 26½"
20½"
24"
UF3 filler provided:
cut to required dimension
for field installation
(May not be needed based
on appliance size.)
Support structure & floor
required to support appliance
above the lower deep drawer box
(not pictured and support
materials are not provided)
All dimensions are nominal. Cabinet requires field alteration and installation that CliqStudios is not responsible for. Two drawer
fronts and two drawer boxes will not be used in this field modified cabinet application and may be saved or discarded. Please
check with appliance manufacturer for final dimensions toconfirm with Designer before placing order.
face frame
width
cabinet back
width
Matching Interior
Side panels and back panel
special ordered by Designer
OCM8
applied
molding
area
Bottom drawer
frame removed
in the field
OCM8 molding
applied in the
field
Base Microwave
Drawer Base Cabinet Field Install
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
18. Most kitchen sinks either drop into a hole in the countertop or are mounted from underneath the countertop. An apron front,
or farm, sink slides into an opening or gap in a countertop and is supported by the cabinet and internal cradle frame work
(not provided by CliqStudios.com) directly underneath the sink.
A large porcelain or cast iron apron front sink can weigh 300 lb. or more when filled with water. The parts listed below
provide only partial support. The installer will need to provide additional cradle framework to support apron front. Apron front
sinks vary greatly in size, style and dimensions that require a custom field installation. Be sure to consult your installer
before determining the final installation. Every apron front sink installation is unique because there are no such thing as a
‘standard’ size apron front, or farm, sink.
Built up toe kick
area (4½" high), front
to back, supporting
WR cabinet
Filler installed
horizontally
DWR3
panel cut in half,
front fillers trimmed
to fit, & used on
each side of sink
Wall Refrigerator (WR)
cabinet top cut out to
allow for plumbing hook ups
WARNING! Confirm with manufacturer for sink dimension and requirements BEFORE cabinet purchase.
4½"
Farm Sink Base 36"
WR36 | DWR - Field Install
page 1 of 5
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
19. Example drawings depict standard depth wall cabinet with
the door and shelves removed.
Installation supports are not provided by CliqStudios.com
manufacturer’s install requirements vary.
WARNING! Cabinet drawing left and below show example wall
cabinet with ¼" reveal and without applied end panels.
¾"
bottom
(½" plywood)
¾"
Ǫ
½"
¾"
side
Cabinet Underhang = ¾" high
Back Panel thickQHVV Ǫ
Side Panel thickness = ½"
Under Wall Cabinet Dimension
For Under Cabinet Lighting
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
20. cabinetfaceframe
cabinetdoor
Cabinet Side
wood blocking
(not provided)
2"
ceiling
AC
M
8
¼"
Crown Molding
ACM8
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
21. ¼"
¾"
96"
BM8
= Finished Panel
= BM8 Molding
BM8 Batten Molding can be used to
cover seems of two finished panels
that have been placed together
panel seam
right
panelleft
panel
floor
left
panel
right
panel
back
side of
island
Back Island Panel
BM8 | FP Panel
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
22. CabinetFaceFrame
CabinetDoor
Base
Cabinet
Side
OGP8
wood blocking
(not provided)
Floor
Void
Toe Kick
Area
¼"
4¾"
Floor
3½"
4½"
Decorative Toekick
OGP8
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
23. Use OGP8 & IQR8 molding for trim along base cabinets and islands for finished furniture look. The IQR8 molding
adds a great dimensional touch and can hide any gaps created if the floor drops.
Base Shoe Molding
OGP8 | IQR8
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
IQR8
OGP8
wall
floor
IQR8
¾”
¾”
96”
OGP8
4¾”
¾”
96”
24. CTM8
1½"
CabinetFaceFrame
CabinetDoor
¾"
Light Rail
CTM8 | Horizontal
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
Cabinet Side
25. CliqStudios.com, LLC reserves the right to change, modify or discontinue programs at any time v 1-2015
Because walls are usually not straight, level, square, flush or plumb we recommend the following
accessories to accommodate constrution space imperfections for the floor, wall or ceiling and may have
included them in your order to finish your space.
Attention:
recommended accessories
for your designDreams designed. Dreams delivered.
96" 4½"
UF1.542 1½" 42"
UF1.596 1½" 96"
UF342 3" 42"
UF336 3" 36"
UF330 3" 30"
UF396 3" 96"
UF642 6" 42"
UF696 6" 96"
A B
A
B
¾"
96"
¾"
¾"
IQR8
ƒ Solid hardwood
ƒ Bold line represents finished edge
¾"
96"
¼"
SM8
ƒ Solid hardwood
ƒ Bold line represents
finished edge
ƒ Solid hardwood
ƒ Front & sides finished
back
wall
floor
side
wall
back
wall
floor
gap created
by filler between
cabinet & wall
Inside Quarter Round is more than a decorative accent.
It is installed after the flooring and is primarily used to
cover the gapping resulting from shims to level cabinets.
Quarter Round can also help cover up gaps in the floor -
especially with tile.
side
wall
back
wall
floor
cabinet
side
floor
back
wallside
wall
cabinet
side
FILLERS
Fillers are used to “fill” the gap between a wall and the
end run of cabinets, and sometimes between cabinets.
Fillers can also be used horizontally for decorative
molding applications. Field install and trim to width/height.
Note: Fillers also are used to provide space between
cabinet and wall for proper door swing operation to
provide cabinet access, especially with decorative
hardware and roll out trays
BTK8
ƒ Plywood veneer w/ engineered core
ƒ Bold line represents finished edge
Base ‘Toe Kick’ is used as a panel to cover up
the gapping created by the placement of
cabinets. It is applied to the recessed area
where the cabinet meets the floor.
SM8, or Scribe molding,
is used along the wall when
cabinets/fillers meet a non-plumb
wall to hide gapping between the
cabinet and the wall.
cabinet
side
26. Wood is a product of nature with different grain patterns, color variations, aging patterns, and mineral
streaks which add to the beauty and distinction of natural hardwood products. These wood variations
are not considered a defect and will not be subject to warranty replacement. Painted Cabinets may
require additional maintenance. Over time, painted finishes will develop hairline cracks from the results
of natural expansion and contraction of the wood.
Visit our website for more information on finish characteristics
Do not begin demolition of space or existing cabinetry prior to receipt and inspection of your new
cabinets, as missing or damaged parts may delay your installation. Any install delays, trip charges,
contractor fees, etc. due to pre-scheduling your installer are your responsibility. CliqStudios.com is not
liable for these costs, and has recommended against installation prior to inspection and receipt of all
original and replacement orders.
measurements
installation
wood & finish characteristics
You have provided, and are responsible for, all measurements. Please verify all dimensions prior to
the purchase of your cabinets:
Any changes made after the order has been placed will be subject to a 25% restocking fee and
additional shipping charges. Visit our website for more information on our Return Policy
At CliqStudios.com, we understand that remodeling projects can be stressful, time consuming, and may
disrupt areas of your home that your rely on. In our experience, making sure that you are aware of what
to expect is the most effective way to navigate the process as smoothly as possible.
Thank you for choosing CliqStudios.com for your cabinetry project!
• Appliances • Window/Door dimensions and location
• Ceiling and/or soffit heights • Special considerations & obstructions
• All drawings, renderings and design information provided by designer
Please read the following carefully prior to the purchase of your order:
what to expect
order confirmation
page 1 of 2
Dreams designed. Dreams delivered.
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.
27. terms & conditions
_________________________________ ____________
Customer Signature Date
_________________________________
Customer Printed Name
In placing your order with Cliqstudios.com, you agree that you have read and understand this
documentation, and that you agree to the terms and conditions of Cliqstudios.com.
I have read and I understand the above Cliqstudios.com Final Steps and have verified and
approved all of the conditions, including any drawings, renderings or pictures of design plan, that
were included with the final design packet with designer.
order receipt & inspection
Once order has been received promptly inspect for any damaged or missing items. If you have any
damaged items you will need to contact Customer Service as soon as possible. Replacement orders
usually ship in less than one week.
• phone: 800.576.7930 ext. 561
• email: customerservice@cliqstudios.com
Standard Home Delivery order will be shipped to a location accessible by a pallet jack to the first
secure, dry area (usually a garage), on the same level as the truck tires. If Standard Home Delivery
cannot be accommodated please contact your designer before purchase to arrange for Limited or
Restricted delivery; additional charges will apply. Cliqstudios.com will notify you once the order has left
our facility via email. You will be contacted to schedule an eight (8) hour delivery window directly by
the delivery carrier. Shipments may be delayed due to weather, mechanical issues, holidays, or other
situations relating to delivery coordination.
standard delivery
If you haven’t already please take the time to view our video which outlines what to expect and easy
things that you can do to make the delivery and receipt of your cabinet order go as smoothly as
possible. Visit our website to view deilvery video
To send signature back to designer you may:
1. Scan & email to your designer
2. Fax to 877-675-4394 attention your designer
3. Or reply back via email confirming your agreement to the Terms & Conditions
what to expect
order confirmation
page 2 of 2
Dreams designed. Dreams delivered.
ph: 800.576.7930 | fax: 877.675.4394 | customerservice@cliqstudios.com
CliqStudios.com®
, LLC reserves the right to change, modify or discontinue policy and products at any time.
All dimensions are nominal. This drawing is only provided as a reference and CliqStudios.com is not responsible for final installation.