M/s Balaji Plastic proposes to establish a PVC granules manufacturing unit with a production capacity of 5 tons per month in Delhi, India. The total capital investment for the project will be Rs. 398,900. The raw materials needed are PVC sole/scrap and waste at 5 tons per month. The manufacturing process involves cutting, mixing, extruding, and cooling the raw materials to produce plastic dana granules, which will then be packed and dispatched. Water consumption will be 300 liters per day, with 200 liters used for cooling recycled on site and 60 liters for domestic use discharged to sewers. There will be no process waste water and air pollution control equipment will be installed.

1. PROJECT REPORT
For
M/S. BALAJI PLASTIC
H-1404, DISDC, NARELA
INDL AREA DELHI-110040
1.0 INTRODUCTION
M/s BALAJI PLASTIC ARE PROPOSED PVC Granauler by using Sole/ Scrab and old
Rexne West Uniton Reprocessing without washing H-1404, DSIDC, NARELA INDL.
AREA, DELHI-110040
Capacity of the PVC Grenus shall be 5 Tons Per Month. The Unit has acquired 350
Sq. Mtr. Area on rent at aforesaid address.
Industrial Activity : PVC GRANULES
Name of Product : FRESH PVC DANA
Production Capacity : 5 Tons Day
By Product : Nil
2.0 TOTAL CAPITAL INVESTMENT
The Proposed total Capital Investment of the Unit Shall be about Rs. 398900.00
Three Lakh Ninty Eight Thousand Nine Hundred Only)
Including Land and Building Plant and Machinery without Depreciation.

2. 3.0 RAW MATERIAL REQUIREMENT
The following raw material shall be required at the time of production
ITEMS QUANTITITY
Fresh PVC (Dana) 5 tons Month (PVC) Dona
PVC Granvles
____________ ____________/Day
4.0 MANUFACTURING PROCESS:
Manufacturing process First of all we are purchase PVC Sole/ Scrap and old
Rxine fresh waste ASA Raw Material. Then it is going to cutte and mixer machine.
Then going to do water is used for the purpose of calling of cose water used for
colling purposes It will be Recycled or Recycle and tank is used and then cutter
These are Plastic Dana Ready.

3. 5.0 FLOW CHART OF MANUFACTURIN GPROCESS
RAW MATERIAL
CUTTER
MIXER
EXTRUDER
COOLING
CUTTING PLASTIC DANA READY
PACKING
DISPATCH

4. 6.0 DETAILS OF WATER CONSUMPTION
Total 300 Lt/Day water are consumed by the Unit. The break up of the Consumption of
water are as under:
A Cooling : 200 Ltr Cooling water on Completely Recycled
B Domestic Use : 100 Ltr/Day)
C Process : Nil
D Others : Nil
7.0 SOURCE & VOLUME OF WASTE WATER DISCHARGE
The break up to waster discharge from the difference sources are as under:
A. Cooling : 200 Ltr/Cooling Water on Complectly Recyeled
B. Domestic Use : 60 Lt/Day
(Discharge in Sewar)
C. Process : NIL
D. Other : NIL
E. Other : NIL

5. 8.0 PROPOSED POLLUTION CONTROL SYSTEM
8.4 AIR POLLUTION:
There will be Air Pollution from the process exhaust Gas from Stock attached to
extrude, Cutter, Mixer & Filter Machine provided hood & channelization. Proper
complete photograph attach.
8.5 WATER POLLUTION WASTE WATER DISCHARGE:
There will be No Source of water pollution. Only Water will be used for Domestic
Purpose Domestic effluent water will be discharged in the public sewer.
8.6 D.G. SET:
There would be no source of Noise Pollution from the process, However if
required necessary control measured shall be taken to meet the ambient noise
standards.