This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle housing.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F2 BACKHOE LOADER HWP
Configuration: 432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06194852
Axle Housing (Service Brakes, Differential and Bevel Gear) -
Disassemble
SMCS - 3256-015; 3258-015; 3260-015; 4251-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 202-7965 Spanner Wrench 1
B 1P-2321 Combination Puller 1
C 235-2784 Adjusting Tool Gp 1
D 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the axle housing.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01636808
1. Remove plates (1), brake discs (2), and brake hub (4) from the brake cylinder assembly.
Remove dowels (3).
Illustration 2 g01636809
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (10), washers (9), bushing (8), and spacer (7). Remove bolts (16), retainers
(15), springs (14), springs (13), and bushings (12), as an assembly. Use a suitable pry bar
and remove brake piston (6) from brake cylinder assembly (11). Remove O-ring seals (5)
from brake piston (6). Repeat this step for the opposite side.
Illustration 3 g01636811
3. Remove bolts (17) from brake cylinder assembly (11).
Illustration 4 g01636812
3/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: Before you remove brake cylinder assembly (11), make location marks for
installation purposes.
4. Remove brake cylinder assembly (11).
5. Repeat Step 3 and Step 4 for the opposite side.
6. Remove the differential and bevel gear assembly (18) from the bevel gear side of the center
housing.
Illustration 5 g01637013
7. Remove bolt (20) and retainer (19). Use Tooling (A) to remove spanner nut (22). If
necessary, remove bearing cup (21) from brake cylinder assembly (11). Repeat this step for
the opposite side.
4/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g01637914
8. Use Tooling (B) in order to remove bearing cone (23).
5/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 7 g01637979
9. Lock the differential in a vise. Remove bolts (24) and bevel gear (25) from the differential.
6/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g01637980
10. Use Tooling (B) to remove bearing cone (26).
Illustration 9 g01637981
11. Remove collar (28), pins (27), and the seals.
7/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g01637983
12. Remove cover (29), thrust washer (30), and side gear (32). Use a suitable punch and a
hammer in order to drive out locking pins (31). Remove planetary shafts (33).
Illustration 11 g01638818
13. Remove thrust washers (34), gears (35), spider (36), side gear (38), and thrust washer (37).
8/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 12 g01638823
14. Remove bolts (40) and remove brake assembly (39) as a unit. Straighten the locking tab
from nut (41).
Illustration 13 g01638831
15. Use Tooling (C) in order to hold brake disc (42) and remove nut (41) (not shown).
9/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 14 g01638834
16. Remove washer (44), O-ring seal (43), and brake disc (42).
Illustration 15 g01638835
17. Remove lip seal (45) from the center housing.
10/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 16 g01639076
18. Tap the end of pinion shaft (46) with a soft hammer in order to remove pinion shaft (46)
from the center housing.
Illustration 17 g01639077
19. Remove bearing cone (48), washers (49), and collapsible spacer (47) from pinion shaft (46).
Discard collapsible spacer (47).
11/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 18 g01639080
20. Use Tooling (D) and a suitable press in order to remove bearing cone (50) from pinion shaft
(46). Remove the shim that is positioned under bearing cone (50). Check the shim for wear.
If necessary, replace the shim.
Illustration 19 g01639081
12/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
21. Remove bolts (66), cover (65), and O-ring seal (64).
22. Remove piston (63) from cover (65). Remove O-ring seals (62) from piston (63).
23. Remove retaining ring (61), bushing (60), and spring (59) from rod (55).
24. Remove bolts (51), cover (52), O-ring seal (53), spring (54), and washer (56) from the
center housing.
25. Remove rod (55) from fork (58). Remove retaining ring (57) from rod (55). Remove fork
(58) from the center housing.
Illustration 20 g01639082
26. Use a suitable hammer and a punch in order to remove bearing cups (67) from the center
housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 10:49:16 UTC+0800 2019
13/13
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F2 BACKHOE LOADER HWP
Configuration: 432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06038944
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 5050-553-PX
Release Procedure
1. Park on a level surface. If you must park on a grade, chock the machine.
2. Apply the service brake in order to stop the machine. Move the transmission control to the
NEUTRAL position.
3. Move the speed control lever to the LOW IDLE position.
4. Engage the parking brake.
5. Engage the transmission neutral lock.
6. Lower all attachments to the ground.
7. Stop the engine.
8. Turn the engine start switch key to OFF position for 4 seconds.
9. Turn the engine start switch key back to ON position without starting the engine.
10. Press the hydraulic shutoff switch to the ON position.
11. Operate all hydraulic controls through all positions in order to relieve hydraulic pressure.
Repeat this step until all hydraulic pressure is released.
12. Move the hydraulic control levers to the HOLD position.
13. Turn the engine start switch to OFF position and remove the key.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 10:50:12 UTC+0800 2019
1/1
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F2 BACKHOE LOADER HWP
Configuration: 432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06190624
Solenoid Valve (Transmission) - Remove and Install
SMCS - 5479-010-T3
Removal Procedure
Illustration 1 g03822061
1. Remove bolts (2), plate (3), and floor mat (1).
1/2
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g03822065
2. Remove bolts (4) and position floorplate (5) to the side.
Illustration 3 g01658935
3. Cut cable straps (8). Disconnect harness assemblies (7). Remove the four plugs and bolts
(6). Remove solenoid valve (9). Repeat for the remaining solenoid valves.
Installation Procedure
1. Install solenoid valve (9) in the reverse order of removal.
a. Tighten bolts (6) in a crisscross pattern to a torque of 1 N·m (9 lb in). Retorque bolts
(6) to a final torque of 8 N·m (71 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 10:51:08 UTC+0800 2019
2/2
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 432F2 BACKHOE LOADER HWP
Configuration: 432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06145776
Transmission (Direct Drive) - Remove
SMCS - 3030-011-DD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-2352 Support Stand As 2
B 444-0526 Air/Hydraulic Jack Gp 1
C
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
D
1U-7505 Hydraulic Jack 1
1U-7558 Mounting Adapter Gp 2
E 456-4449 Support Tube 1
F 1U-7505 Hydraulic Jack 1
G 308-3471 Jack Stand Gp 2
1. Connect the lock for the boom. Refer to Operation and Maintenance Manual, "Boom Lock".
2. Connect the lock for the swing boom. Operation and Maintenance Manual, "Swing Lock
Pin Control".
3. Connect the lock for the extendable stick. Refer to Operation and Maintenance Manual,
"Extendable Stick Lock Control ".
1/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Lower the bucket to the ground. Place the control for the bucket into the FLOAT position.
Illustration 1 g03094942
5. Use Tooling (B) to raise the front of the machine. Position two of Tooling (A) under the
front of the machine.
Illustration 2 g03826593
6. Raise the machine so that the machine is level and 1270 mm (50.0 inch) off the floor.
Position two of Tooling (C) under the rear of the machine.
7. Drain the transmission. Refer to Operation and Maintenance Manual, "Transmission Oil -
Change" for the correct draining procedure.
2/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g03826658
8. Use two people in order to remove guard assembly (2). The weight of guard assembly (2) is
approximately 32 kg (70 lb). Remove bolts (1) and guard assembly (2).
9. Remove the piston pump. Refer to Disassembly and Assembly Manual, "Piston Pump
(Main Hydraulic) - Remove and Install".
10. Remove the front drive shaft if applicable. Refer to Disassembly and Assembly Manual,
"Drive Shaft (Front) - Remove and Install".
11. Remove the rear drive shaft. Refer to Disassembly and Assembly Manual, "Drive Shaft
(Rear) - Remove and Install".
Illustration 4 g03826775
12. Disconnect harness assembly (3).
Illustration 5 g03827467
13. Disconnect hose assembly (4).
3/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 6 g03826776
14. Disconnect harness assembly (6). Remove bolt (7) and reposition shift rod assembly (5) out
of the way.
Illustration 7 g03826777
15. Remove bolt (8) that retains the transmission filler tube.
Illustration 8 g03826778
16. Disconnect hose assembly (9).
17. Loosen clamp (10) and disconnect hose (11).
4/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 9 g03826779
18. Remove transmission oil filter (12) in order to remove the bell housing bolts.
19. Loosen clamp (13) and disconnect hose (14).
Illustration 10 g03826781
20. Remove bolts (16) and cover (15).
Illustration 11 g03826782
21. Rotate the flywheel in order to access bolts (17). Remove bolts (17).
5/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 12 g03826781
22. Reinstall cover (15) and bolts (16).
Illustration 13 g03826783
Illustration 14 g03826996
23. Attach Tooling (F) to transmission (20).
6/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
25. 24. Install Tooling (D), Tooling (E), and Tooling (G) in order to support engine (18).
25. With engine (18) and transmission (20) supported remove the nuts, the washers, and bolts
(19).
Illustration 15 g03827045
26. Remove bolts (21) and the washers from transmission (20).
Illustration 16 g03827474
27. Place a suitable cable strap (22) around drive plate (23) for the converter.
Illustration 17 g03826785
7/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 28. Use Tooling (F) in order to remove transmission (20). The weight of transmission (20) is
approximately 255 kg (562 lb).
Illustration 18 g03827094
29. Cut cable straps (26).
30. Disconnect connector assembly (24), connector assembly (25), connector assembly (27),
and connector assemblies (28). Remove the harness assembly from the transmission.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 10:52:03 UTC+0800 2019
8/8
432F2 Side Shift Backhoe Loader HWP00001-UP (MACHINE) POWERED BY C4.4 ...
2019/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...