Recommended
Recommended
More Related Content
Similar to Question 3. 3. (TCO 1) _____ control(s) which end devices are allo.docx
Similar to Question 3. 3. (TCO 1) _____ control(s) which end devices are allo.docx (20)
More from wraythallchan
More from wraythallchan (20)
Recently uploaded
Recently uploaded (20)
Question 3. 3. (TCO 1) _____ control(s) which end devices are allo.docx
- 1. Question 3. 3. (TCO 1) _____ control(s) which end devices are allowed to communicate on the network. (Points : 5) The access layer Business goals Collapsed core Convergence Question 4. 4. (TCO 1) _____ will determine the design requirements for a network. (Points : 5) Business goals Personal preference Location None of the above Question 5. 5. (TCO 1) Which of the following illustrates properly designed hierarchical networks that achieve near-wire speed among all devices? (Points : 5) Collapsed core Convergence The core layer Performance Question 6. 6. (TCO 2) Startup configuration is stored in ________. (Points : 5) ROM PRAM NVRAM Flash Question 7. 7. (TCO 2) The average amount of data that is
- 2. actually transmitted as opposed to the rating of the port is _____. (Points : 5) source MAC address switch fabric throughput unicast transmission Question 8. 8. (TCO 2) _____ is a Layer 2 identifier for the frame's originating NIC or interface. (Points : 5) Propagation delay Source MAC address Switch fabric Throughput Question 9. 9. (TCO 2) _____ is a dedicated connection between two hosts. (Points : 5) Half-duplex communication Latency Microsegment Multicast transmission Question 10. 10. (TCO 2) A _____ is a frame that is sent from one host and addressed to one specific destination. (Points : 5) source MAC address switch fabric throughput unicast transmission Question 11. 11. (TCO 3) Extended-range VLANs are identified by a VLAN ID between which of the following ranges? (Points : 5) 1,000-9,000
- 3. 1,006-4,094 1,006-2,094 1,000-4,094 Question 12. 12. (TCO 3) A _____ VLAN is a VLAN that is configured to carry only user-generated traffic. These VLANs are sometimes referred to as user VLANs. (Points : 5) data default native none of the above Question 13. 13. (TCO 3) Which VLANs are allowed over the link when a new trunk link is configured on an IOS-based switch? (Points : 5) All defined VLANs are allowed on the trunk by default. Each VLAN, or VLAN range, that is specified with the switchport mode command Each VLAN, or VLAN range, that is specified with the vtp domain command Each VLAN, or VLAN range, that is specified with the VLAN database command Question 14. 14. (TCO 3) Which would not be one of the characteristics of a typical VLAN? (Points : 5) VLANs logically divide a switch into multiple, independent switches at Layer 2. Trunk links can carry traffic for multiple VLANs. VLAN implementation significantly increases traffic due to added trunking information. A VLAN can span multiple switches.
- 4. Question 15. 15. (TCO 3) Which of the following configures the port to negotiate a trunk? (Points : 5) Switchport mode trunk Switchport mode dynamic desirable Switchport nonegotiate Switchport mode access 1. (TCO 3) Which of the following best describes the mapping between VLANs and IP subnets in a modern switched network? (Points : 5) One VLAN to many IP subnets One IP subnet to one VLAN One IP subnet to many VLANs Varies with the model of Cisco Catalyst switch Question 2. 2. (TCO 3) Which of following VLAN frame encapsulation types are configurable on a Cisco switch? (Points : 5) VTP 802.1Q LLC None of the above Question 3. 3. (TCO 4) Which of the following depicts a VTP domain? (Points : 5) Switches share VLAN information; the boundary is defined by a Layer 3 device. It can only create, delete, and modify local VLANs. It advertises VLAN configuration information and can create, delete, and modify VLANs. It restricts broadcast traffic to those trunks that must be used to reach the destination devices.
- 5. Question 4. 4. (TCO 4) A _____ stores VLAN information only in RAM. (Points : 5) VTP client VTP domain VTP pruning VTP server Question 5. 5. (TCO 4) Which VTP mode should a Cisco switch be set to if this switch is to add or delete VLANs to a management domain? (Points : 5) Transparent Server Auto Client Question 6. 6. (TCO 5) Which of the following is the closest to the root bridge? (Points : 5) Root port Spanning Tree Protocol Spanning-tree algorithm Switch diameter Question 7. 7. (TCO 5) What is the time spent in the listening and learning states called? (Points : 5) Forward delay Forwarding state Hello time Learning state Question 8. 8. (TCO 5) The time between each BPDU sent on a port is called which of the following? (Points : 5) Forwarding state
- 6. Hello time Learning state Listening state Question 9. 9. (TCO 5) A term for when the port is administratively shut down is _____. (Points : 5) designated ports disabled state forward delay forwarding state Question 10. 10. (TCO 5) In the _____ state, the MAC address table is built but does forward user data frames. (Points : 5) forwarding hello time learning listening Question 11. 11. (TCO 5) Which contains a priority value and the MAC address? (Points : 5) Bridge priority Bridge protocol data unit Designated ports Bridge ID Question 12. 12. (TCO 6) VLAN is a logical group of ports, usually belonging to _____ to control the size of the broadcast domain. (Points : 5) a single IP subnet multiple IP subnets either a single IP subnet or to multiple IP subnets none of the above
- 7. Question 13. 13. (TCO 6) Which command is used to determine whether inter-VLAN communication is functioning? (Points : 5) show vlan ping ipconfig show interface Question 14. 14. (TCO 6) Inter-VLAN routing _____ additional subnet broadcast addresses. (Points : 5) requires does not require sometimes requires none of the above Question 15. 15. (TCO 6) How many physical interfaces are required to perform inter-VLAN routing with traditional inter- VLAN routing? (Points : 5) One port per VLAN Two ports per VLAN Four ports per VLAN No physical interface per VLAN