Caterpillar cat 321 d lcr excavator (prefix mdt) service repair manual (mdt00001 and up)

Service Repair Manual
Model
321D LCR EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 321D LCR EXCAVATOR MDT
Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04786161
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE...
2019/10/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01375221
(2) Fuel injection pump drive gear
(3) Idler gear
Note: Align timing marks on pump drive gear (2) and idler gear (3) that were made in the
removal procedure
1. Position the O-ring seal and fuel injection pump (21) .
2. If you are reusing pump drive gear (2) , align the marks on pump drive gear (2) and idler
gear (3) .

3. If replacing the pump drive gear or a problem is encountered, refer to Testing and
Adjusting, "Fuel Injection Timing-Check" for the correct procedure.
4. Install bolts (24) .
5. Install two bolts (23) (not shown).
6. Install bolts (22) .
7. Install cover (1) .
8. Install new washers and tube assembly (10) .

9. Install new washers and connect hose assembly (18) . Install bolt (19) . Tighten bolt (19) to
a torque of 34 ± 4 N·m (25 ± 3 lb ft).
10. Install new washers and install hose assembly (17) . Install bolt (16) . Tighten bolt (16) to a
torque of 34 ± 4 N·m (25 ± 3 lb ft).
11. Connect harness assembly (15) .
12. Install tube assembly (14) . Tighten each end of tube assembly (14) to a torque of 41 ± 5
N·m (30 ± 4 lb ft).
13. Install new washers and connect tube assembly (10) . Install fitting (11) . Tighten fitting
(11) to a torque of 25 + 3 - 0 N·m (18 + 2 - 0 lb ft).
14. Connect hose (13) and tighten clamp (12) .
15. Install bracket assembly (8) and tube assembly (9) . Tighten each end of tube assembly (9)
to a torque of 19 ± 5 N·m (14 ± 4 lb ft).
16. Connect harness assembly (7) .

17. Install new washers and connect hose assemblies (6) .
18. Install nut (5) . Tighten nut (5) to a torque of 34 ± 4 N·m (25 ± 3 lb ft).
19. Connect hose (4) .
End By: Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 7 16:15:03 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02746250
Fuel Injection Pump Gear - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-7465 Puller Gp 1
Start By:
a. Remove the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove".
b. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers

before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Remove nut (1).
2. Use Tooling (A) in order to remove fuel injection pump gear (2).

3. Remove key (3).
Mon Oct 7 16:15:59 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04762770
Fuel Injection Pump Gear - Install
SMCS - 1251-012
NOTICE
1. Install key (3) .

Note: The use of a soft jaw vice is to keep fuel injection pump gear (2) stationary to tighten
nut (1) .
2. Place fuel injection pump gear (2) into a soft jaw vice. Tighten nut (1) to a torque of 90 ± 6
N·m (66 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install".
Mon Oct 7 16:16:55 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02746266
Electronic Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
A 5F-4764 Pry Bar 1
B 278-4138 Fuel System Protection Gp(1)
1
(1)
This tool can only be used one time.
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
b. Remove the fuel Injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove".
NOTICE
performance of inspection, maintenance, testing, adjusting, and repair
containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
NOTICE
Do not open the high pressure fuel system without allowing the fuel
system to purge. After the engine has shut down, allow the fuel system to
purge for ten minutes. This operating fuel system contains high
pressure. Exposure to high pressure fuel can result in personal injury.
Note: Before opening the fuel system, the engine must be turned off for at least one minute.
Note: Use Caterpillar Electronic Technician (ET) to verify that the fuel system pressure is at zero
before opening the fuel system.
Note: Use Tooling (B) after any fuel line has been disconnected.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of
the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism.
Note: Put identification marks on harness assemblies and electronic unit injectors for installation
purposes.

1. Loosen nuts (2).
2. Disconnect harness assembly (1).
3. Remove bolt (3) and the washer.
4. Place an identification mark on electronic unit injector (4) for installation purposes. Each
electronic unit injector must be reinstalled in the original location. Use Tooling (A) in order
to remove electronic unit injector (4).
5. Remove clamp (5) (not shown).
6. Repeat Steps 1 through 5 for the remaining electronic unit injectors.
Mon Oct 7 16:17:51 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05281314
Electronic Unit Injector - Install
SMCS - 1290-012
NOTICE
1. Install a new O-ring and a new copper washer onto the electronic unit injector (not shown).
Install clamp (5) (not shown) onto electronic unit injector (4) . Install electronic unit injector
(4) .

2. Install bolt (3) and the washer.
Note: Note the orientation of the washer for installation.
3. Connect harness assembly (1) and tighten nuts (2) to a torque of 2.5 N·m (22 lb in).
4. Repeat Steps 1 through 3 for the remaining electronic unit injectors.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Mon Oct 7 16:18:46 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02747029
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
1. Loosen clamp (1).

Typical Example
2. Remove nuts (4) and tube (6). Disconnect tube assemblies (2) and (7). Disconnect hoses (5)
and (9). Remove nuts (8) and turbocharger (3).
Mon Oct 7 16:19:42 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02746993
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Table 1
Required Tools
A 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
NOTICE
performance of inspection, maintenance, testing, adjusting, and repair
containing fluids.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
2. Remove gasket (1) from the cartridge.
3. Remove gasket (2) from the turbine housing.
4. Remove the bolt and nut (3) from clamp (4). Remove clamp (4) that secures turbine housing
(5) to cartridge (6).
5. Separate turbine housing (5) fromcartridge (6).

6. Use Tooling (A) in order to remove retaining ring (7) from compressor housing (8).
7. Separate compressor housing (8) from cartridge (6).
Mon Oct 7 16:20:38 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02747012
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
Table 1
Required Tools
A 1P-1861 Retaining Ring Pliers 1
NOTICE
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.

1. Install cartridge (6) into compressor housing (8).
2. Use Tooling (A) in order to install retaining ring (7) into compressor housing (8).
3. Install cartridge (6) into turbine housing (5).
4. Install clamp (4) that secures cartridge (6) and turbine housing (5) together. Install the bolt
and nut (3) into clamp (4).

Note: Refer to the Specifications Module , "Turbocharger" for information on the clamp.
5. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
6. Install gasket (2) on the turbine housing.
7. Install gasket (1) on the cartridge.
End By:
a. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Mon Oct 7 16:21:34 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02747030
Turbocharger - Install
SMCS - 1052-012
Table 1
Required Tools
A 5P-3931 Anti-Seize Compound 1
Typical Example
1. Install turbocharger (3). Apply Tooling (A) to nuts (8) and install nuts (8). Tighten nuts (8)
to a torque of 54 ± 5 N·m (40 ± 4 lb ft). Connect hoses (5) and (9). Connect tube assemblies
(2) and (7). Install tube (6) and nuts (4).

Caterpillar cat 321 d lcr excavator (prefix mdt) service repair manual (mdt00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Caterpillar cat 321 d lcr excavator (prefix mdt) service repair manual (mdt00001 and up)

Similar to Caterpillar cat 321 d lcr excavator (prefix mdt) service repair manual (mdt00001 and up) (20)

More from ufdjjsekkmdme

More from ufdjjsekkmdme (16)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 321 d lcr excavator (prefix mdt) service repair manual (mdt00001 and up)