SlideShare a Scribd company logo
Service Repair Manual
Models
M325B MH WHEELED
EXCAVATOR
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 19 20:22:27 UTC+0800 2020
5/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 19 20:23:22 UTC+0800 2020
5/5(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 19 20:24:18 UTC+0800 2020
3/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.
1/4(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 1 g00661331
Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
Illustration 2 g00750163
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".
2/4(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.
3/4(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 5 g00655975
14. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 19 20:25:14 UTC+0800 2020
4/4(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00775441
2/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 2 g00625237
1. Remove fuel injector hold-down bolt (1) .
Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could
occur. The unit injector has a notch on the opposite side of the rack. This notch is used for
prying the unit injector loose. Some fuel injector racks move freely when the spring is not
compressed. Do not move the fuel injector rack without compressing the fuel injector spring
slightly. Damage may occur to the unit injector.
2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage
injector rack bar (3) from fuel injection control linkage (2) .
3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 19 20:26:09 UTC+0800 2020
3/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M325B WHEELED EXCAVATOR BGN
Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919370
Unit Injector - Install
SMCS - 1290-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 4C-5553 Injector Seat Cleaning Brush 1
C 173-1530 Injector Seating Tool 1
D 143-2099 Unit Injector Tool Group (Sleeve Replacement) 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the unit injector sleeve for pitting and for carbon tracking. Used unit injector sleeves
do not need to be reamed unless the seated area is pitted or eroded. If the seated area has
excessive carbon deposits, the used unit injector sleeves need to be reamed. Refer to Tool
Operating Manual, NEHS0675, "Using the 143-2099 Sleeve Replacement Tool Group on
3114, 3116, and 3126 Engines". Use Tooling (D) to ream injector sleeves.
2. Inspect the condition of the O-ring seals on the unit injector. Replace the seals, if necessary.
1/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
3. Lubricate the O-ring seals with clean engine oil.
Illustration 1 g00775441
4. Position the unit injector in the cylinder head and rotate the unit injector in order to engage
injector rack bar (3) with fuel injection control linkage (2) . Push down on the unit injector
and ensure that the unit injector is properly seated in the cylinder head.
Note: Do not use fuel injector hold-down bolt (1) to pull the unit injector into the cylinder
head.
5. Install a new fuel injector hold-down bolt (1) in the hold-down bracket for the unit injector.
Tighten fuel injector hold-down bolt (1) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
Note: Do not overtighten fuel injector hold-down bolt (1) . Excessive torque may cause
damage to the unit injector and the unit injector may seize.
6. Refer to the Tool Operating Manual, NEHS0738, "Using the 173-1530 Injector Seating
Tool Group on 3114, 3116, and 3126 MUI or 3126 HEUI 2-Valve Engines" for the
remaining steps on installing the unit injector.
7. Synchronize the unit injectors. Refer to Testing and Adjusting, "Unit Injector
Synchronization - Adjust".
2/3(W)
w
2020/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

More Related Content

More from udjkskdmmd

Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...
Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...
Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...udjkskdmmd
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...udjkskdmmd
 
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...udjkskdmmd
 
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...udjkskdmmd
 
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...udjkskdmmd
 
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
 
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
 
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...udjkskdmmd
 
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...udjkskdmmd
 
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...udjkskdmmd
 
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...udjkskdmmd
 
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...udjkskdmmd
 

More from udjkskdmmd (20)

Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...
Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...
Caterpillar Cat 416D BACKHOE LOADER (Prefix BKG) Service Repair Manual Instan...
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual Instan...
 
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...
Caterpillar Cat 322N EXCAVATOR (Prefix 9JL) Service Repair Manual Instant Dow...
 
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...
Caterpillar Cat 322L TRACK EXCAVATOR (Prefix 7WL) Service Repair Manual Insta...
 
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...
Caterpillar Cat 322CLN EXCAVATOR (Prefix BGR) Service Repair Manual Instant D...
 
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...
 
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...
 
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...
Caterpillar Cat M317D2 Wheeled Excavator (Prefix CH5) Service Repair Manual I...
 
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8D) Service Repair Manual Instant ...
 
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix LWA) Service Repair Manual Instant ...
 
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4Z) Service Repair Manual Instant ...
 
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...
Caterpillar Cat 966F WHEEL LOADER (Prefix 8BG) Service Repair Manual Instant ...
 
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z4D) Service Repair Manual Instant ...
 
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...
Caterpillar Cat 966D WHEEL LOADER (Prefix 35S) Service Repair Manual Instant ...
 
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...
Caterpillar Cat M318F Wheeled Excavator (Prefix FB8) Service Repair Manual In...
 
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...
Caterpillar Cat M325C MH WHEELED EXCAVATOR (Prefix PAN) Service Repair Manual...
 
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...
Caterpillar Cat M320 Excavator (Prefix 9PS) Service Repair Manual Instant Dow...
 
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...
Caterpillar Cat M317F Wheeled Excavator (Prefix F6P) Service Repair Manual In...
 
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z9K) Service Repair Manual Instant ...
 
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...
Caterpillar Cat 993K Wheel Loader (Prefix Z8Z) Service Repair Manual Instant ...
 

Recently uploaded

Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerKapil Thakar
 
Essential Maintenance Tips For Commercial Vans.
Essential Maintenance Tips For Commercial Vans.Essential Maintenance Tips For Commercial Vans.
Essential Maintenance Tips For Commercial Vans.commercialvansolutions
 
Automotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatAutomotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatKapil Thakar
 
What Should You Do If Your Jaguar XF Bluetooth Isn't Working
What Should You Do If Your Jaguar XF Bluetooth Isn't WorkingWhat Should You Do If Your Jaguar XF Bluetooth Isn't Working
What Should You Do If Your Jaguar XF Bluetooth Isn't WorkingAuto Assets
 
Advanced Technology for Auto Part Industry Inventory Solutions
Advanced Technology for Auto Part Industry Inventory SolutionsAdvanced Technology for Auto Part Industry Inventory Solutions
Advanced Technology for Auto Part Industry Inventory Solutionscontactcaysonandres
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceKapil Thakar
 
What Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsWhat Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsSchearer's Sales & Service Inc
 
Basic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CBasic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CKapil Thakar
 
Car Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideCar Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideAskXX.com
 
Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Hyundai Motor Group
 
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理psavhef
 
Introduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceIntroduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceKapil Thakar
 
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
 

Recently uploaded (13)

Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
 
Essential Maintenance Tips For Commercial Vans.
Essential Maintenance Tips For Commercial Vans.Essential Maintenance Tips For Commercial Vans.
Essential Maintenance Tips For Commercial Vans.
 
Automotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatAutomotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame Format
 
What Should You Do If Your Jaguar XF Bluetooth Isn't Working
What Should You Do If Your Jaguar XF Bluetooth Isn't WorkingWhat Should You Do If Your Jaguar XF Bluetooth Isn't Working
What Should You Do If Your Jaguar XF Bluetooth Isn't Working
 
Advanced Technology for Auto Part Industry Inventory Solutions
Advanced Technology for Auto Part Industry Inventory SolutionsAdvanced Technology for Auto Part Industry Inventory Solutions
Advanced Technology for Auto Part Industry Inventory Solutions
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming Sequence
 
What Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsWhat Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission Problems
 
Basic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CBasic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in C
 
Car Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideCar Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection Guide
 
Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'
 
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
 
Introduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceIntroduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS Service
 
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
 

Caterpillar Cat M325B MH WHEELED EXCAVATOR (Prefix BGN) Service Repair Manual Instant Download.pdf

  • 1. Service Repair Manual Models M325B MH WHEELED EXCAVATOR
  • 2. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928381 Governor - Remove SMCS - 1264-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers(1) 1 (1) This tool is part of the 128-8822 Fuel System and Governor Tool Group. Start By: a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid - Remove and Install". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. 1/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 3. Illustration 1 g00613041 1. Disconnect the governor control cable. 2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio control (3), if equipped. Plug and cap all connections. Illustration 2 g00613071 3. Remove clip (4). 2/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 4. Illustration 3 g00655975 4. Use Tooling (A) to slide tube assembly (5) into the cylinder head. Illustration 4 g00613149 5. Remove the clip and use Tooling (A) to remove the clevis pin (6). Note: Clevis pin (6) must stay with the governor in order to be adjusted. 3/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 5. Illustration 5 g00613563 6. Remove bolts (7) and the washers that hold the governor in position. Illustration 6 g00673182 7. Remove the governor from the engine. Illustration 7 g00673180 8. Remove O-ring seal (3) on the governor. Illustration 8 g00672742 4/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 6. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head. Illustration 9 g00672733 10. Remove O-ring seal (2) on the tube assembly (5). Illustration 10 g00673178 11. Remove O-ring seal (1) from the cylinder head. Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, & 3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor Calibration Bench. For information on reusability of components in the governor, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue May 19 20:22:27 UTC+0800 2020 5/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 7. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928419 Governor - Install SMCS - 1264-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers(1) 1 B 128-8827 Pin(1) 1 1U-7523 Pin Pilot(1) 1 (1) This tool is part of the 128-8822 Governor Tool Group. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, & 3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor Calibration Bench. For information on reusability of components in the governor, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". 1/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 8. Illustration 1 g00673178 1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head. Illustration 2 g00672733 2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly (5). Illustration 3 g00672742 3. Install the O-ring seal and tube assembly (5) in the cylinder head. 2/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 9. Illustration 4 g00673180 4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor. Illustration 5 g00673182 5. Place the governor in position on the engine. Illustration 6 g00613563 6. Install the washers and bolts (7) that hold the governor in place. 3/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 10. Illustration 7 g00672755 7. Install clevis pin (6) in Tooling (B). Illustration 8 g00672752 8. Use Tooling (B) to install clevis pin (6) and the clip. 9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118. 4/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 11. Illustration 9 g00655975 10. Use Tooling (A) to slide tube assembly (5) into the governor. Illustration 10 g00613071 11. Install clip (4). Illustration 11 g00613041 12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio control (3), if equipped. Plug and cap all connections. 13. Install the governor control cable. End By: a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue May 19 20:23:22 UTC+0800 2020 5/5(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 12. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928445 Fuel Injection Control Linkage - Remove SMCS - 1298-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers 1 Start By: a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 13. Illustration 1 g00613071 1. Remove clip (4). Clip (4) is located between the governor and the cylinder head. Illustration 2 g00655975 2. Use Tooling (A) to slide tube assembly (5) into the cylinder head. Illustration 3 g00613149 2/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 14. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects the governor to the control lever of the fuel injection control linkage. Note: Clevis pin (6) must stay with the governor in order to be adjusted. Illustration 4 g00630566 4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects the fuel injection control linkage (2) to the governor. Note: For information on the inspection procedure for control lever (3), refer to Special Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P-9048 Fuel Injection Control Linkage". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue May 19 20:24:18 UTC+0800 2020 3/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 15. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928573 Fuel Injection Control Linkage - Install SMCS - 1298-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers(1) 1 B 128-8827 Pin(1) 1 1U-7523 Pin Pilot(1) 1 C 1U-6675 Spring Compressor(1) 6 D 128-8822 Fuel System and Governor Tool Gp 1 (1) This tool is part of the 128-8822 Governor Tool Group. 1/4(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 16. Illustration 1 g00661331 Note: For information on the inspection procedure for control lever (3), refer to Special Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P -9048 Fuel Injection Control Linkage". 1. Loosen setscrews (4) on each bracket. 2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the bolts. 3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in). 4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in). 5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod. 6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of 3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates freely. 7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever (3). Illustration 2 g00750163 8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control linkage (2). Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector - Install". 2/4(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 17. 9. Install Tooling (C) on the unit injectors and compress the springs. Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)". Illustration 3 g00672755 10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor. Illustration 4 g00672752 11. Use Tooling (B) to install clevis pin (6) and the clip. 12. Use Tooling (D) to set the unit injector synchronization. Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)". 13. Remove Tooling (C) from the unit injectors. 3/4(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 18. Illustration 5 g00655975 14. Use Tooling (A) to slide tube assembly (5) into the governor. Illustration 6 g00613071 15. Install clip (4). End By: a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue May 19 20:25:14 UTC+0800 2020 4/4(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 19. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i05919358 Unit Injector - Remove SMCS - 1290-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-0302 Bar 1 Start By: A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers 1/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 20. before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00775441 2/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 21. Illustration 2 g00625237 1. Remove fuel injector hold-down bolt (1) . Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could occur. The unit injector has a notch on the opposite side of the rack. This notch is used for prying the unit injector loose. Some fuel injector racks move freely when the spring is not compressed. Do not move the fuel injector rack without compressing the fuel injector spring slightly. Damage may occur to the unit injector. 2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage injector rack bar (3) from fuel injection control linkage (2) . 3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue May 19 20:26:09 UTC+0800 2020 3/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 22. Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M325B WHEELED EXCAVATOR BGN Configuration: M325B Material Handler BGN00001-UP (MACHINE) POWERED BY 3116 Engine Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i05919370 Unit Injector - Install SMCS - 1290-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty B 4C-5553 Injector Seat Cleaning Brush 1 C 173-1530 Injector Seating Tool 1 D 143-2099 Unit Injector Tool Group (Sleeve Replacement) 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Inspect the unit injector sleeve for pitting and for carbon tracking. Used unit injector sleeves do not need to be reamed unless the seated area is pitted or eroded. If the seated area has excessive carbon deposits, the used unit injector sleeves need to be reamed. Refer to Tool Operating Manual, NEHS0675, "Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines". Use Tooling (D) to ream injector sleeves. 2. Inspect the condition of the O-ring seals on the unit injector. Replace the seals, if necessary. 1/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 23. Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
  • 24. 3. Lubricate the O-ring seals with clean engine oil. Illustration 1 g00775441 4. Position the unit injector in the cylinder head and rotate the unit injector in order to engage injector rack bar (3) with fuel injection control linkage (2) . Push down on the unit injector and ensure that the unit injector is properly seated in the cylinder head. Note: Do not use fuel injector hold-down bolt (1) to pull the unit injector into the cylinder head. 5. Install a new fuel injector hold-down bolt (1) in the hold-down bracket for the unit injector. Tighten fuel injector hold-down bolt (1) to a torque of 12 ± 3 N·m (106 ± 27 lb in). Note: Do not overtighten fuel injector hold-down bolt (1) . Excessive torque may cause damage to the unit injector and the unit injector may seize. 6. Refer to the Tool Operating Manual, NEHS0738, "Using the 173-1530 Injector Seating Tool Group on 3114, 3116, and 3126 MUI or 3126 HEUI 2-Valve Engines" for the remaining steps on installing the unit injector. 7. Synchronize the unit injectors. Refer to Testing and Adjusting, "Unit Injector Synchronization - Adjust". 2/3(W) w 2020/5/19 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...