SlideShare a Scribd company logo
Service Repair Manual
Model
428C BACKHOE LOADER
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02105278
Fuel Injection Pump - Remove - Type 2 Engines and 7BJ
Engines
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
150-3992 Timing Pin (1)
1
150-3993 Timing Pin (2)
1
B
171-1085
or
173-9774
Tamper Resistant Tool Gp 1
( 1 )
Tool (A) is required in order to remove Bosch fuel injection pumps.
( 2 )
Tool (A) is required in order to remove Delphi (Lucas) and Stanadyne fuel injection pumps.
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the No. 1 cylinder is at the top center position on the compression stroke. Refer
to the Testing and Adjusting, "Fuel System" topic for additional information.
Illustration 1 g00808245
2. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking
spacer (1) into position (B). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft).
2/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00808370
Typical example
Note: Do not remove hub nut (4) from the shaft of the fuel injection pump. The hub of the
fuel injection pump is installed in the correct position from the factory in order to ensure
proper timing. If hub nut (4) is removed and the hub is removed, the hub will need to be
accurately installed on the shaft of the fuel injection pump by the use of special equipment.
Refer to your Caterpillar Dealer for more information.
Note: Do not release Torx screws (5) (if equipped). If the Torx screws are released and the
timing plate is moved, the timing position that is set at the factory will be lost. If the Torx
screws are released, the No. 1 cylinder must be set to the top center position on the
compression stroke before the Torx screws are tightened.
3. Slowly rotate the crankshaft until hole (6) in the timing gear and hole (7) in the hub are in
alignment with hole (8) in the fuel injection pump body.
Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the
top of the fuel injection pump. The location of Tool (A) for Delphi (Lucas) and Stanadyne
fuel injection pumps will be located toward the bottom of the fuel injection pump.
4. Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A)
into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the
fuel injection pump timing is correct. No resistance should be felt when the timing pin is
inserted into hole (8) of the fuel injection pump body.
3/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Note: Some fuel injection pumps are installed with tamper proof bolts. Tool (B) may be
necessary in order to remove the tamper proof bolts.
5. Remove four bolts (3) that fasten the fuel injection pump gear to the fuel injection pump.
Timing gear (9) should be free from the fuel injection pump shaft.
Illustration 3 g00808376
Typical example
6. Remove three flange nuts (10) and fuel injection pump (11) from the engine.
Illustration 4 g01059878
Typical example
7. Remove O-ring seal (12) from fuel injection pump (11) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:28:17 UTC+0800 2019
4/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01083652
Fuel Injection Pump - Remove - Type 1 Engines and 9RM
Engines
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-9774 Bolt Remover (1)
1
B 9U-6198 Crankshaft Turning Tool 1
C
8S-2264 Puller Group 1
8S-4712 Bolt 2
( 1 )
The bolt remover is required in order to remove the tamper proof bolts on the access cover for the fuel injection
pump.
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
1/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00545256
1. Remove four bolts (1) .
Note: Some engines may have four tamper proof bolts (1). Use Tool (A) in order to remove
the tamper proof bolts bolts.
2. Remove cover (2) .
2/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00545258
3. Remove nut (3) and the lockwasher.
Illustration 3 g00571370
4. Use Tool (B) to rotate the crankshaft until keyway (X) is at 30 degrees from the vertical
centerline.
Illustration 4 g00571373
3/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Install Tool (C) .
6. Disengage the gear from the fuel injection pump.
Illustration 5 g00545262
7. Disconnect hose (7) from the fuel injection pump.
8. Remove three nuts (6) that hold fuel injection pump (5) in position.
9. Remove fuel injection pump (5) and the gasket.
Note: Ensure that you do not lose the key when the fuel injection pump is removed. Also
notice the position of marks (4) in order to ensure proper alignment of fuel injection pump
(5) during installation.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:29:13 UTC+0800 2019
4/4
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02046409
Fuel Injection Pump - Install - Type 2 Engines and 7BJ
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
150-3992 Timing Pin (1)
1
150-3993 Timing Pin (2)
1
B
171-1085
or
173-9774
Tamper Resistant Tool Gp 1
( 1 )
Tooling (A) is required in order to install Bosch fuel injection pumps.
( 2 )
Tooling (A) is required in order to install Dephi (Lucas) and Stanadyne fuel injection pumps.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01059878
Typical example
1. Check the condition of O-ring seal (13) on fuel injection pump (12). If the seal is worn or
damaged, replace the seal.
2. Lightly lubricate O-ring seal (13) with clean engine oil. Install O-ring seal (13) on fuel
injection pump (12) .
NOTICE
The No. 1 cylinder must be at the top center position on the
compression stroke before the fuel injection pump is installed. If the
crankshaft needs to be rotated, the fuel injection pump must be
mounted temporarily or the loose gear could cause damage to the front
housing.
Illustration 2 g00808376
Typical example
2/5
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Put fuel injection pump (12) in position on the engine. Ensure that the timing gear is aligned
with the hub of fuel injection pump (12). Install three flange nuts (11) and tighten the flange
nuts to a torque of 28 N·m (21 lb ft).
Illustration 3 g00808370
Typical example
4. Position gear (9) on the shaft of the fuel injection pump.
Note: Some fuel injection pumps are installed with tamper proof bolts. Tooling (B) may be
necessary in order to install the tamper proof bolts.
5. Put the timing gear plate in position and install four bolts (3). Tighten the four bolts finger
tight.
Note: The fuel injection pump gear will only fit in one position. Install the gear with the
letters "C" and "M" facing away from the engine.
3/5
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 4 g00808245
Typical example
6. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking
spacer (1) into position (A). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft).
Note: The location of Tooling (A) for Bosch fuel injection pumps will be located toward the
top of the fuel injection pump. The location of Tooling (A) for Dephi (Lucas) and
Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection
pump.
7. Install Tooling (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tooling
(A) into position in hole (8) in the fuel injection pump body. If Tooling (A) can be fully
seated, the fuel injection pump timing is correct. No resistance should be felt when the
timing pin is inserted into hole (8) of the fuel injection pump body.
NOTICE
The fuel injection pump may be supplied with the fuel injection pump
shaft in the locked position. The drive shaft of the fuel injection pump
must not be rotated without the spacer in position under the locking
screw. Damage to the drive shaft of the fuel injection pump will result.
8. When the timing plate is installed, rotate gear (9) by hand in a counterclockwise direction in
order to remove the backlash between gear (9) and the idler gear. Do not rotate the
crankshaft or the fuel injection pump shaft. Tighten bolts (3) to a torque of 28 N·m (21 lb
ft).
9. Remove Tooling (A) from the fuel injection pump gear.
4/5
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:30:10 UTC+0800 2019
5/5
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01083913
Fuel Injection Pump - Install - Type 1 Engines and 9RM
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-9774 Bolt Remover (1)
1
( 1 )
The bolt remover is required in order to install the tamper proof bolts on the access cover for the fuel injection
pump.
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of the gasket for the fuel injection pump. Replace the gasket, if
necessary.
1/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00545262
2. Install the gasket and fuel injection pump (5) .
Note: Align marks (4) that are on fuel injection pump (5) and the timing gear cover.
3. Install the key.
4. Install three nuts (6) that hold fuel injection pump (5) in position.
5. Connect hose (7) to fuel injection pump (5) .
6. Engage the gear with the fuel injection pump.
Illustration 2 g00545258
7. Install the lockwasher and nut (3) .
2/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00545256
8. Install cover (2) and four bolts (1) .
Note: Some engines have four tamper proof bolts (1). Use Tool (A) in order to install the
four bolts.
9. Set the timing of the fuel injection pump. Refer to the Testing and Adjusting Module for the
correct procedure.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:31:07 UTC+0800 2019
3/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01051839
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
Illustration 1 g00545445
Typical example
1. Loosen two clamps (1) .
2. Slide hose (2) away from turbocharger (3) .
3. Remove two bolts (4) and the gasket.
4. Disconnect oil return line (6) from the cylinder block and remove the gasket.
5. Remove nuts (5) .
Illustration 2 g00545446
Typical example
6. Remove three bolts (7) .
2/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Remove turbocharger (3) and the gaskets.
8. Plug all openings immediately.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:32:04 UTC+0800 2019
3/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 2CR
Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01051906
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
1. Place an index mark on all of the components for the assembly procedure.
Illustration 1 g00545460
Typical example
2. Remove elbow (1) and the O-ring seal.
3. Remove two bolts (2) .
4. Remove hose assembly (3) and the gasket.
Illustration 2 g00545463
Typical example
5. Remove six bolts (4) .
6. Remove three clamps (5) .
7. Separate compressor housing (6) from cartridge (7) .
2/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00545464
Typical example
Illustration 4 g00545505
Typical example
8. Remove six bolts (8) .
9. Remove three clamps (9) .
10. Separate cartridge (7) from turbine housing (10) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 15:33:00 UTC+0800 2019
3/3
428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

More from udjkdsdmmd

Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
udjkdsdmmd
 
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
udjkdsdmmd
 
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
udjkdsdmmd
 
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
udjkdsdmmd
 
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
udjkdsdmmd
 
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
udjkdsdmmd
 
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
udjkdsdmmd
 
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
udjkdsdmmd
 
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
udjkdsdmmd
 
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
udjkdsdmmd
 
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
udjkdsdmmd
 
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
udjkdsdmmd
 
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
udjkdsdmmd
 
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
udjkdsdmmd
 
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
udjkdsdmmd
 
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
udjkdsdmmd
 
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
udjkdsdmmd
 
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
udjkdsdmmd
 
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
udjkdsdmmd
 
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
udjkdsdmmd
 

More from udjkdsdmmd (20)

Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
Caterpillar Cat 637E Wheel Scraper (Prefix 1LB) Service Repair Manual (1LB000...
 
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 76Y) Service Repair Manual (76Y00001...
 
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
Caterpillar Cat 953 TRACK LOADER (Prefix 77Y) Service Repair Manual (77Y01093...
 
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
Caterpillar Cat 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual (8NB0245...
 
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 20Z) Service Repair Manual (20Z00001...
 
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00001...
 
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
Caterpillar Cat 953 TRACK LOADER (Prefix 44Z) Service Repair Manual (44Z00735...
 
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
Caterpillar Cat 631G WHEEL SCRAPER (Prefix DEM) Service Repair Manual (DEM000...
 
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
Caterpillar Cat 627F Wheel Tractor (Prefix 1DL) Service Repair Manual (1DL000...
 
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
Caterpillar Cat 623G Wheel Tractor (Prefix DBC) Service Repair Manual (DBC000...
 
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
Caterpillar Cat 623F Wheel Tractor (Prefix 5EW) Service Repair Manual (5EW000...
 
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
Caterpillar Cat 621H WHEEL TRACTOR (Prefix HKK) Service Repair Manual (HKK000...
 
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
Caterpillar Cat 621E WHEEL TRACTOR (Prefix 6AB) Service Repair Manual (6AB000...
 
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
Caterpillar Cat 621E WHEEL SCRAPER (Prefix 6BB) Service Repair Manual (6BB000...
 
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix JEY) Service Repair Manual (JEY00001 an...
 
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix HBS) Service Repair Manual (HBS00001 an...
 
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 an...
 
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
Caterpillar Cat 438D BACKHOE LOADER (Prefix BPE) Service Repair Manual (BPE00...
 
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR03...
 
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
Caterpillar Cat 438C BACKHOE LOADER (Prefix 2DR) Service Repair Manual (2DR02...
 

Recently uploaded

Why Is Your BMW X3 Hood Not Responding To Release Commands
Why Is Your BMW X3 Hood Not Responding To Release CommandsWhy Is Your BMW X3 Hood Not Responding To Release Commands
Why Is Your BMW X3 Hood Not Responding To Release Commands
Dart Auto
 
Ec330B Lc Excavator Volvo Service Repair.pdf
Ec330B Lc Excavator Volvo Service Repair.pdfEc330B Lc Excavator Volvo Service Repair.pdf
Ec330B Lc Excavator Volvo Service Repair.pdf
Excavator
 
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
Bertini's German Motors
 
gtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
gtycccccccccccccccccccccccccccccccccccccccccccccccccccccccgtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
gtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
4thzenzstar
 
Ec460b lc Excavator Volvo Service Repair.pdf
Ec460b lc Excavator Volvo Service Repair.pdfEc460b lc Excavator Volvo Service Repair.pdf
Ec460b lc Excavator Volvo Service Repair.pdf
Excavator
 
Antique Plastic Traders Company Profile
Antique Plastic Traders Company ProfileAntique Plastic Traders Company Profile
Antique Plastic Traders Company Profile
Antique Plastic Traders
 
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out HereWhy Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Masters European & Gapanese Auto Repair
 
Tyre Industrymarket overview with examples of CEAT
Tyre Industrymarket overview with examples of CEATTyre Industrymarket overview with examples of CEAT
Tyre Industrymarket overview with examples of CEAT
kshamashah95
 
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
European Service Center
 
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
Autohaus Service and Sales
 
Things to remember while upgrading the brakes of your car
Things to remember while upgrading the brakes of your carThings to remember while upgrading the brakes of your car
Things to remember while upgrading the brakes of your car
jennifermiller8137
 
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
amvovau
 
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
psavhef
 
Empowering Limpopo Entrepreneurs Consulting SMEs.pptx
Empowering Limpopo Entrepreneurs  Consulting SMEs.pptxEmpowering Limpopo Entrepreneurs  Consulting SMEs.pptx
Empowering Limpopo Entrepreneurs Consulting SMEs.pptx
Precious Mvulane CA (SA),RA
 
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptxStatistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
coc7987515756
 
What Exactly Is The Common Rail Direct Injection System & How Does It Work
What Exactly Is The Common Rail Direct Injection System & How Does It WorkWhat Exactly Is The Common Rail Direct Injection System & How Does It Work
What Exactly Is The Common Rail Direct Injection System & How Does It Work
Motor Cars International
 
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Hyundai Motor Group
 
What Does the Active Steering Malfunction Warning Mean for Your BMW
What Does the Active Steering Malfunction Warning Mean for Your BMWWhat Does the Active Steering Malfunction Warning Mean for Your BMW
What Does the Active Steering Malfunction Warning Mean for Your BMW
Tanner Motors
 
Wondering if Your Mercedes EIS is at Fault Here’s How to Tell
Wondering if Your Mercedes EIS is at Fault Here’s How to TellWondering if Your Mercedes EIS is at Fault Here’s How to Tell
Wondering if Your Mercedes EIS is at Fault Here’s How to Tell
Vic Auto Collision & Repair
 

Recently uploaded (19)

Why Is Your BMW X3 Hood Not Responding To Release Commands
Why Is Your BMW X3 Hood Not Responding To Release CommandsWhy Is Your BMW X3 Hood Not Responding To Release Commands
Why Is Your BMW X3 Hood Not Responding To Release Commands
 
Ec330B Lc Excavator Volvo Service Repair.pdf
Ec330B Lc Excavator Volvo Service Repair.pdfEc330B Lc Excavator Volvo Service Repair.pdf
Ec330B Lc Excavator Volvo Service Repair.pdf
 
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs Attention
 
gtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
gtycccccccccccccccccccccccccccccccccccccccccccccccccccccccgtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
gtyccccccccccccccccccccccccccccccccccccccccccccccccccccccc
 
Ec460b lc Excavator Volvo Service Repair.pdf
Ec460b lc Excavator Volvo Service Repair.pdfEc460b lc Excavator Volvo Service Repair.pdf
Ec460b lc Excavator Volvo Service Repair.pdf
 
Antique Plastic Traders Company Profile
Antique Plastic Traders Company ProfileAntique Plastic Traders Company Profile
Antique Plastic Traders Company Profile
 
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out HereWhy Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
 
Tyre Industrymarket overview with examples of CEAT
Tyre Industrymarket overview with examples of CEATTyre Industrymarket overview with examples of CEAT
Tyre Industrymarket overview with examples of CEAT
 
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
What Causes 'Trans Failsafe Prog' to Trigger in BMW X5
 
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...
 
Things to remember while upgrading the brakes of your car
Things to remember while upgrading the brakes of your carThings to remember while upgrading the brakes of your car
Things to remember while upgrading the brakes of your car
 
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
一比一原版BC毕业证波士顿学院毕业证成绩单如何办理
 
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
一比一原版SDSU毕业证圣地亚哥州立大学毕业证成绩单如何办理
 
Empowering Limpopo Entrepreneurs Consulting SMEs.pptx
Empowering Limpopo Entrepreneurs  Consulting SMEs.pptxEmpowering Limpopo Entrepreneurs  Consulting SMEs.pptx
Empowering Limpopo Entrepreneurs Consulting SMEs.pptx
 
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptxStatistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
Statistics5,c.xz,c.;c.;d.c;d;ssssss.pptx
 
What Exactly Is The Common Rail Direct Injection System & How Does It Work
What Exactly Is The Common Rail Direct Injection System & How Does It WorkWhat Exactly Is The Common Rail Direct Injection System & How Does It Work
What Exactly Is The Common Rail Direct Injection System & How Does It Work
 
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Core technology of Hyundai Motor Group's EV platform 'E-GMP'
Core technology of Hyundai Motor Group's EV platform 'E-GMP'
 
What Does the Active Steering Malfunction Warning Mean for Your BMW
What Does the Active Steering Malfunction Warning Mean for Your BMWWhat Does the Active Steering Malfunction Warning Mean for Your BMW
What Does the Active Steering Malfunction Warning Mean for Your BMW
 
Wondering if Your Mercedes EIS is at Fault Here’s How to Tell
Wondering if Your Mercedes EIS is at Fault Here’s How to TellWondering if Your Mercedes EIS is at Fault Here’s How to Tell
Wondering if Your Mercedes EIS is at Fault Here’s How to Tell
 

Caterpillar Cat 428C BACKHOE LOADER (Prefix 2CR) Service Repair Manual (2CR16212-19309).pdf

  • 2. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i02105278 Fuel Injection Pump - Remove - Type 2 Engines and 7BJ Engines SMCS - 1251-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 150-3992 Timing Pin (1) 1 150-3993 Timing Pin (2) 1 B 171-1085 or 173-9774 Tamper Resistant Tool Gp 1 ( 1 ) Tool (A) is required in order to remove Bosch fuel injection pumps. ( 2 ) Tool (A) is required in order to remove Delphi (Lucas) and Stanadyne fuel injection pumps. Start By: A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove". B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Ensure that the No. 1 cylinder is at the top center position on the compression stroke. Refer to the Testing and Adjusting, "Fuel System" topic for additional information. Illustration 1 g00808245 2. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking spacer (1) into position (B). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft). 2/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. Illustration 2 g00808370 Typical example Note: Do not remove hub nut (4) from the shaft of the fuel injection pump. The hub of the fuel injection pump is installed in the correct position from the factory in order to ensure proper timing. If hub nut (4) is removed and the hub is removed, the hub will need to be accurately installed on the shaft of the fuel injection pump by the use of special equipment. Refer to your Caterpillar Dealer for more information. Note: Do not release Torx screws (5) (if equipped). If the Torx screws are released and the timing plate is moved, the timing position that is set at the factory will be lost. If the Torx screws are released, the No. 1 cylinder must be set to the top center position on the compression stroke before the Torx screws are tightened. 3. Slowly rotate the crankshaft until hole (6) in the timing gear and hole (7) in the hub are in alignment with hole (8) in the fuel injection pump body. Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tool (A) for Delphi (Lucas) and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump. 4. Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A) into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body. 3/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. Note: Some fuel injection pumps are installed with tamper proof bolts. Tool (B) may be necessary in order to remove the tamper proof bolts. 5. Remove four bolts (3) that fasten the fuel injection pump gear to the fuel injection pump. Timing gear (9) should be free from the fuel injection pump shaft. Illustration 3 g00808376 Typical example 6. Remove three flange nuts (10) and fuel injection pump (11) from the engine. Illustration 4 g01059878 Typical example 7. Remove O-ring seal (12) from fuel injection pump (11) . Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:28:17 UTC+0800 2019 4/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01083652 Fuel Injection Pump - Remove - Type 1 Engines and 9RM Engines SMCS - 1251-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 173-9774 Bolt Remover (1) 1 B 9U-6198 Crankshaft Turning Tool 1 C 8S-2264 Puller Group 1 8S-4712 Bolt 2 ( 1 ) The bolt remover is required in order to remove the tamper proof bolts on the access cover for the fuel injection pump. Start By: A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove". B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and Assembly, "Engine Design" topic. NOTICE Keep all parts clean from contaminants. 1/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00545256 1. Remove four bolts (1) . Note: Some engines may have four tamper proof bolts (1). Use Tool (A) in order to remove the tamper proof bolts bolts. 2. Remove cover (2) . 2/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. Illustration 2 g00545258 3. Remove nut (3) and the lockwasher. Illustration 3 g00571370 4. Use Tool (B) to rotate the crankshaft until keyway (X) is at 30 degrees from the vertical centerline. Illustration 4 g00571373 3/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. 5. Install Tool (C) . 6. Disengage the gear from the fuel injection pump. Illustration 5 g00545262 7. Disconnect hose (7) from the fuel injection pump. 8. Remove three nuts (6) that hold fuel injection pump (5) in position. 9. Remove fuel injection pump (5) and the gasket. Note: Ensure that you do not lose the key when the fuel injection pump is removed. Also notice the position of marks (4) in order to ensure proper alignment of fuel injection pump (5) during installation. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:29:13 UTC+0800 2019 4/4 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i02046409 Fuel Injection Pump - Install - Type 2 Engines and 7BJ Engines SMCS - 1251-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 150-3992 Timing Pin (1) 1 150-3993 Timing Pin (2) 1 B 171-1085 or 173-9774 Tamper Resistant Tool Gp 1 ( 1 ) Tooling (A) is required in order to install Bosch fuel injection pumps. ( 2 ) Tooling (A) is required in order to install Dephi (Lucas) and Stanadyne fuel injection pumps. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/5 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. Illustration 1 g01059878 Typical example 1. Check the condition of O-ring seal (13) on fuel injection pump (12). If the seal is worn or damaged, replace the seal. 2. Lightly lubricate O-ring seal (13) with clean engine oil. Install O-ring seal (13) on fuel injection pump (12) . NOTICE The No. 1 cylinder must be at the top center position on the compression stroke before the fuel injection pump is installed. If the crankshaft needs to be rotated, the fuel injection pump must be mounted temporarily or the loose gear could cause damage to the front housing. Illustration 2 g00808376 Typical example 2/5 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. 3. Put fuel injection pump (12) in position on the engine. Ensure that the timing gear is aligned with the hub of fuel injection pump (12). Install three flange nuts (11) and tighten the flange nuts to a torque of 28 N·m (21 lb ft). Illustration 3 g00808370 Typical example 4. Position gear (9) on the shaft of the fuel injection pump. Note: Some fuel injection pumps are installed with tamper proof bolts. Tooling (B) may be necessary in order to install the tamper proof bolts. 5. Put the timing gear plate in position and install four bolts (3). Tighten the four bolts finger tight. Note: The fuel injection pump gear will only fit in one position. Install the gear with the letters "C" and "M" facing away from the engine. 3/5 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. Illustration 4 g00808245 Typical example 6. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking spacer (1) into position (A). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft). Note: The location of Tooling (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tooling (A) for Dephi (Lucas) and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump. 7. Install Tooling (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tooling (A) into position in hole (8) in the fuel injection pump body. If Tooling (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body. NOTICE The fuel injection pump may be supplied with the fuel injection pump shaft in the locked position. The drive shaft of the fuel injection pump must not be rotated without the spacer in position under the locking screw. Damage to the drive shaft of the fuel injection pump will result. 8. When the timing plate is installed, rotate gear (9) by hand in a counterclockwise direction in order to remove the backlash between gear (9) and the idler gear. Do not rotate the crankshaft or the fuel injection pump shaft. Tighten bolts (3) to a torque of 28 N·m (21 lb ft). 9. Remove Tooling (A) from the fuel injection pump gear. 4/5 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. End By: a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:30:10 UTC+0800 2019 5/5 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01083913 Fuel Injection Pump - Install - Type 1 Engines and 9RM Engines SMCS - 1251-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 173-9774 Bolt Remover (1) 1 ( 1 ) The bolt remover is required in order to install the tamper proof bolts on the access cover for the fuel injection pump. Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and Assembly, "Engine Design" topic. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Inspect the condition of the gasket for the fuel injection pump. Replace the gasket, if necessary. 1/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. Illustration 1 g00545262 2. Install the gasket and fuel injection pump (5) . Note: Align marks (4) that are on fuel injection pump (5) and the timing gear cover. 3. Install the key. 4. Install three nuts (6) that hold fuel injection pump (5) in position. 5. Connect hose (7) to fuel injection pump (5) . 6. Engage the gear with the fuel injection pump. Illustration 2 g00545258 7. Install the lockwasher and nut (3) . 2/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. Illustration 3 g00545256 8. Install cover (2) and four bolts (1) . Note: Some engines have four tamper proof bolts (1). Use Tool (A) in order to install the four bolts. 9. Set the timing of the fuel injection pump. Refer to the Testing and Adjusting Module for the correct procedure. End By: a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install". b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:31:07 UTC+0800 2019 3/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01051839 Turbocharger - Remove SMCS - 1052-011 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 19. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 20. Illustration 1 g00545445 Typical example 1. Loosen two clamps (1) . 2. Slide hose (2) away from turbocharger (3) . 3. Remove two bolts (4) and the gasket. 4. Disconnect oil return line (6) from the cylinder block and remove the gasket. 5. Remove nuts (5) . Illustration 2 g00545446 Typical example 6. Remove three bolts (7) . 2/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. 7. Remove turbocharger (3) and the gaskets. 8. Plug all openings immediately. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:32:04 UTC+0800 2019 3/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 22. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 428C BACKHOE LOADER 2CR Configuration: 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWERED BY 3054 Engine Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01051906 Turbocharger - Disassemble SMCS - 1052-015 Disassembly Procedure Start By: A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 23. 1. Place an index mark on all of the components for the assembly procedure. Illustration 1 g00545460 Typical example 2. Remove elbow (1) and the O-ring seal. 3. Remove two bolts (2) . 4. Remove hose assembly (3) and the gasket. Illustration 2 g00545463 Typical example 5. Remove six bolts (4) . 6. Remove three clamps (5) . 7. Separate compressor housing (6) from cartridge (7) . 2/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 24. Illustration 3 g00545464 Typical example Illustration 4 g00545505 Typical example 8. Remove six bolts (8) . 9. Remove three clamps (9) . 10. Separate cartridge (7) from turbine housing (10) . Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Oct 16 15:33:00 UTC+0800 2019 3/3 428C Backhoe Loader Side Shift, Parallel Lift 2CR16212-19309 (MACHINE) POWE... 2019/10/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...