1. Clean the sealing surfaces of the crankcase and cylinder head gasket surfaces. Ensure dowel sleeves are in place.
2. Lightly oil the cylinder head bolts.
3. Follow the specific tightening order and torque specifications shown in the diagram. Tighten in stages until the final torque is reached.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Volvo EC210B F EC210BF Excavator Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Engine, description
D6D Engine
The engine is a 6-cylinder, 4-stroke, direct injected, turbocharged, aftercooled with a cast iron block and cylinder head.
Gears in the engine gear case are hardened helical type for strength and reduced noise, arranged to provide quiet, smooth
transmission of power.
The cylinder block and head are designed with internal passages forming galleries for both lubricating oil and coolant.
The fan belt is a poly type V-belt for improved performance and an auto tension adjuster maintains belt tension.
2. Figure 1
Engine, start motor side view
1 Fuel suction port 11 Blow-by gas pipe 21 Coolant pump
2 Engine oil filter 12 Air inlet (from air cleaner) 22 Belt tensioner
3 Old, Fuel filter (0.5 liters) 13 Turbocharger 23 Air outlet (to charge air cooler)
4 Unit injection pump 14 Exhaust gas outlet 24 Fan drive pulley
5 Emission label 15 Exhaust manifold 25 Air conditioner compressor pulley
6 Engine name plate 16 Intake manifold 26 Pulley with vibration damper
7 Power take off device (option) 17 Air inlet (from charge air cooler) 27 Flywheel
8 Fan drive 18 Lifting eye (front) 28 Lifting eye (rear)
3. 9 Coolant make up port 19 Alternator 29 Crankcase breather
10 Coolant outlet (to radiator) 20 Fuel feed pump 30 Coolant temperature sensor port
Figure 2
New, Fuel filter
1 Fuel filter (1.0 liters)
2 Bracket
Serial number
Europe North America China
Old, Fuel filter Fuel filter (0.5 liters) and bracket ~ 14467 ~ 14317 ~ 30840
New, Fuel filter Fuel filter (1.0 liters) and bracket 14468 ~ 14318 ~ 30841 ~
4. Figure 3
Engine, air heater side view
1 Coolant inlet (from radiator) 14 Engine speed sensor 27 Belt tensioner
2 Coolant outlet (to radiator) 15 Fuel pressure holding valve 28 Engine oil level gauge
3 Coolant make up port 16 Solenoid valve 29 Engine oil pressure sensor
4 Air inlet (from air cleaner) 17 Crankcase breather 30 Fuel suction port
5. 5 Turbocharger 18 Blowby gas pipe 31 Coolant filter return port
6 Intake manifold 19 Valve cover 32 -
7 Exhaust manifold 20 Engine oil cooler 33 Coolant supply to cab heater
8 Starter 21 Fuel filter 34 Coolant heater port
9 Poly-vee belt 22 Engine oil filter 35 Air heater relay
10 Lube oil pipe (supply) 23 Air inlet (from charge air cooler) 36 Oil drain hose
11 Lube oil pipe (return) 24 Alternator 37 Fuel feed pump
12 Engine oil pan 25 Fuel feed pump 38 E-ECU
13 Power take off device 26 Coolant pump
D6E Engine
The D6E configuration is a four stroke, straight six cylinder, turbocharged, direct injected diesel engine with charge air
cooling and wet, replaceable cylinder liners.
The D6E engine uses a Common Rail Fuel System controlled by the engine electronic control (E-ECU) software.
Electronically controlled IEGR (Internal Exhaust Gas Recirculation) reduces NO formation and lowers emissions without the
need for exhaust after treatment. Volvo's latest engine management system, E-ECU is used to control all engine electronic
functions.
The cylinders are numbered consecutively beginning at the flywheel end. Engine rotational direction is counterclockwise as
seen from the flywheel end.
Figure 4
Engine, D6E
6. Service Information
Document Title: Function Group: Information Type: Date:
Engine, identification 200 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Engine, identification
Identification plate
The engine model, serial number and performance data are stamped on an identification plate which is attached on the
cylinder head cover. The engine model designation and serial number must be indicated when ordering spare parts.
Figure 1
Engine identification, D6E
7. Service Information
Document Title: Function Group: Information Type: Date:
Engine, tightening torques 200 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Engine, tightening torques
NOTICE
Regarding bolted joints which are not listed here, see “Volvo standard tightening torques”
Engine, tightening torque
Rocker arm bracket on cylinder head 30 Nm (22.2 lbf ft)
Cylinder head cover (M6) on cylinder head 13 Nm (9.6 lbf ft)
Exhaust return module on cylinder head Step 1: 10 Nm (7.4 lbf ft)
Step 2: 30 Nm (22.2 lbf ft)
Lock nut, valve adjusting screw 20 ±2 Nm (14.8 ±1.5 lbf ft)
Locking screw on cylinder head 34 Nm (25.2 lbf ft)
Solenoid valve on cylinder head 24 Nm (17.8 lbf ft)
Front cover on crankcase Step 1: 3 Nm (2.2 lbf ft)
Step 2: 21 Nm (15.5 lbf ft)
Drain plug on oil pan, M18 55 Nm (40.7 lbf ft)
Crankcase ventilation on cylinder head 21 Nm (15.5 lbf ft)
Return line to return stop valve 30 Nm (22.2 lbf ft)
Return stop valve to crankcase 80 Nm (59.2 lbf ft)
Impulse transmitter (crankshaft) on holder on front cover 9 Nm (6.7 lbf ft)
Impulse transmitter (camshaft) on gearcase 9 Nm (6.7 lbf ft)
Turbocharger on exhaust manifold 42 Nm (31.1 lbf ft)
Clamping shoe injector on cylinder head 16 Nm (11.8 lbf ft)
Injection lines on rail and injector, high pressure line on high-pressure
pump
25 Nm (18.5 lbf ft)
Fuel supply pump on holder 22 Nm (16.3 lbf ft)
Holder fuel supply pump on holder 30 Nm (22.2 lbf ft)
V-belt pulley on fuel supply pump 27 Nm (20.0 lbf ft)
High pressure pump on crankcase, M10 Step 1: 10 Nm (7.4 lbf ft)
Step 2: 50 Nm (37.0 lbf ft)
Fuel control valve 30 Nm (22.2 lbf ft)
Fuel pipe on high pressure pump 29 Nm (21.5 lbf ft)
Fuel pipe on control block 39 Nm (28.9 lbf ft)
Rail on cylinder head 30 Nm (22.2 lbf ft)
Pressure relief valve on rail 100 Nm (74.0 lbf ft)
Rail pressure sensor on rail 70 Nm (51.8 lbf ft)
Pipe clips, fuel line fastening 30 Nm (22.2 lbf ft)
Fuel line on control block, fuel filter console and rail 39 Nm (28.9 lbf ft)
Fuel pipe (return) on control block 49 Nm (36.3 lbf ft)
Fuel pipe (return) on cylinder head 29 Nm (21.5 lbf ft)
Fuel line on fuel filter8 39 Nm (28.9 lbf ft)
Fuel filter console/radiator tank on crankcase 30 Nm (22.2 lbf ft)
9. Service Information
Document Title: Function Group: Information Type: Date:
Component locations 200 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Component locations
D6E Engine
Component position, engine D6E. The following figures show the position of a number of components on engine D6E.
Figure 1
Component locations, front side
1 Engine oil filler 11 Oil dipstick
2 Air inlet 12 Power take off
3 Transport eye 13 Engine oil filter
4 Alternator 14 Connection to E-ECU
5 Fuel feed pump 15 Fuel filter
6 V-rib belt drive on crankshaft 16 Crankcase bleeding valve
7 V-rib belt 17 High pressure fuel pump
8 Automatic belt tensioner 18 Common rail
9 Coolant pump 19 Injector
10 Engine oil cooler
10. Figure 2
Component locations, flywheel side
21 Crankcase bleeding valve 28 Turbocharger
22 Charge air manifold 29 Coolant inlet
23 Flywheel housing 30 Air outlet (to charge air cooler)
24 Drain plug 31 Coolant outlet
25 Oil pan 32 Air inlet (from charge air cooler)
26 Starter motor 33 Exhaust manifold
27 Oil return line from turbocharger 34 Cylinder rocker arm cover
11. Service Information
Document Title: Function Group: Information Type: Date:
Engine characteristic curve 210 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Engine characteristic curve
D6D Engine
Figure 1
12. Engine, characteristic curve
P Output power
S Engine speed
T Torque
F Fuel consumption
D6E Engine
Figure 2
Engine, characteristic curve
P Output power
S Engine speed
T Torque
be Fuel consumption
13. Service Information
Document Title: Function Group: Information Type: Date:
Basic check, Engine 210 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Basic check, Engine
NOTE!
Certain tests and checks are performed with unlocked safety locking lever. Make sure that the machine cannot operate
unexpectedly when the safety locking lever is unlocked.
Purpose of the basic check
The purpose of the basic check is to provide fast and accurate information about the general condition of the engine.
The basic check should be performed and evaluated according to instructions in the PC-tool VCADS Pro.
Tests included in the basic check
The basic check which is divided into the following tests should be performed after reading out error codes and checking
parameters.
Tests:
1.
2.
3.
4.
Cylinder compression, test
The purpose of the test is to show if any cylinder has a deviating compression pressure. The test replaces the old
pressure check method but does not give any absolute values.
Cylinder balancing, test
The purpose of the test is to show if there is any deviation in the fuel injection to a cylinder.
Feed pressure, test
The purpose of the test is to check that the feed pressure is as per specification.
Sensor, test
The purpose of the test is to check the function of all sensors.
14. Service Information
Document Title: Function Group: Information Type: Date:
Troubleshooting 210 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Troubleshooting
General about troubleshooting
When a malfunction is suspected or has been confirmed, it is important to identify the cause as soon as possible.
The starting point for all troubleshooting is that there is some type of trouble symptom or malfunction.
Malfunctions can be indicated by:
generation of error codes
detection of a malfunction symptom.
Troubleshooting work
The first step in troubleshooting is to gather information from the operator concerning the malfunction symptoms, see
Electrical and information system, Collection of basic data. Then, attempt to pin-point the cause by checking in a certain
order, for more information, see Electrical and information system, troubleshooting strategy.
The different checking steps are:
Check error codes
Check parameters
Perform basic check
Troubleshooting information
The following is included in Electrical and information system and is used when troubleshooting:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Troubleshooting strategy
Describes troubleshooting work, step by step.
Troubleshooting, assistive devices
Brief summary of the assistive devices that are available for troubleshooting.
Functional checks and tests, VCADS Pro
Brief description of VCADS Pro. For a detailed description, see VCADS Pro User’s Manual.
Error code information
Contains information regarding error code design, lists of all error codes and error code information about each
error code.
Components, troubleshooting and specifications
Contains methods and measuring values for troubleshooting of components. Also includes wiring diagrams and
certain specifications.
Parameters
Incorrectly set parameters may cause malfunction symptoms. The parameter list includes all limit and command
values for parameters.
Control units, functional description
Describes the functions of the control units, inputs and outputs as well as communication between the various
control units.
Control units, active and passive measuring
Contains measuring values for active and passive measuring of the ECUs.
Software functions
Describes the pre-requisite conditions for the control and monitoring functions that are performed by the software
in the ECUs.
15. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder head, description 211 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Go back to Index Page
Cylinder head, description
D6D Engine
The cylinder head of the D6D engine is made of grey cast iron and designed as block type head.The combustion air enters
vertically and the exhaust air is discharged laterally.Inlet and outlet are located on one side of the cylinder head.
16. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder head, description 211 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Go back to Index Page
Cylinder head, description
D6E Engine
The cylinder head is made of grey cast iron and is common for all cylinders. The induction air enters vertically (A) and the
exhausts leave horizontally (B). Inlets and exhaust outlets are located on the same side of the cylinder block. Inlet and
exhaust valve size is increased to optimize the gas exchange and combustion process. Valve guides are replaceable. Coolant
flow in the cylinder head is modified to accommodate an outlet controlled cooling system.
On order for the engine to fulfill governing emission standards, there are 3 cylinder head gaskets of different thicknesses
between the cylinder head and the piston.
Figure 1
17. Service Information
Document Title: Function Group: Information Type: Date:
Determining cylinder head
gasket
211 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Determining cylinder head gasket
The thickness of the cylinder head gasket is responsible for the correct piston crown clearance of the engine. The
piston crown clearance (0.65 mm) essentially influences the combustion and thus:
Power
Fuel consumption
Exhaust emission
The piston crown clearance is adjusted by determining the piston projection and the thickness of the cylinder head
gasket.
Measuring piston projection
A dial gauge with a fixture is needed to measure the piston projection.
The piston is in its TDC position above the cylinder block face.
Figure 1
Measurement, piston projection
18. 1.
2.
3.
Dial gauge
Bridge
Two spacer plates
A.
B.
C.
Set the dial gauge on the level of the cylinder block face to "zero".
Position the dial gauge at measuring points (C), at the piston pin axis, on the piston and determine the
maximum projection.
Measuring points on the piston.
Distance X = 90 mm
This measurement is performed on each piston. The maximum measured piston projection determines the thickness of the
cylinder head gasket (see table). There are 3 different gasket thicknesses identified by bores (4):
1 bore = 1.2 mm
2 bores = 1.3 mm
3 bores = 1.4 mm
Piston projection
Piston projection Identification of cylinder head gasket
0.33 ∼ 0.55 mm 1 bore
0.56 ~ 0.65 mm 2 bores
0.66 ~ 0.76 mm 3 bores
19. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
20. Service Information
Document Title: Function Group: Information Type: Date:
Fitting cylinder head 211 Service Information 2014/6/11
Profile:
EXC, EC210B F [GB]
Fitting cylinder head
Op nbr 21182
1. Prior to fitting the cylinder head onto the crankcase, the sealing surfaces for the cylinder head gasket must be clean
and free from oil. Pay attention to dowel sleeves.
2. Lightly oil the cylinder head bolts.
3. It is absolutely necessary to observe the bolt tightening order in the adjacent schematic.
Figure 1
Tightening order (exhaust manifold side)
Tightening torque specification:
1st step: 30 N·m (22.2 lbf·ft, 3.1 kgf·m)
2nd step: 80 N·m (59 lbf·ft, 8.2 kgf·m)
3rd step: 90° turn
Tightening order