This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engines and other relevant components. The manual provides specifications, torque values, and other technical information needed for repair and maintenance of these vehicles.
Daewoo doosan solar 140 w v wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and instructions for operating and maintaining a Daewoo excavator. It includes locations of safety labels on the machine, precautions for lifting loads, unauthorized modifications, hazards, starting and operating the machine, maintenance, batteries, towing, shipping and lift capacity tables. Operators must read the manual thoroughly before use to safely handle, operate and service the excavator.
Daewoo doosan dx160 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage lines, hot fluids that can cause burns, and rotating or moving parts that can cause injury.
Daewoo doosan dx140 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage electrical lines, hot fluids that can cause burns, and rotating equipment that can cause injury.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjsjjdkemmde
This document provides an operation and maintenance manual for a Doosan wheel loader model DL420. It includes safety information, descriptions of machine components and controls, operating instructions, maintenance procedures, and specifications. Operators and maintenance personnel must read and understand the entire manual before operating or servicing the machine to avoid serious injury or death.
Daewoo doosan dl300 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies locations of safety labels on the machine and warns that unauthorized modifications could create safety hazards.
- Operators and maintenance personnel are instructed to read the entire manual before use to understand all safety precautions.
Daewoo doosan dl200 tc wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using safety features properly, operating only if feeling well, and being aware of hazards inside the operator's cabin.
Daewoo doosan dl200 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using the machine as intended, following all safety procedures, and ensuring safety features like guards are in good condition.
Daewoo doosan 470 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan solar 140 w v wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and instructions for operating and maintaining a Daewoo excavator. It includes locations of safety labels on the machine, precautions for lifting loads, unauthorized modifications, hazards, starting and operating the machine, maintenance, batteries, towing, shipping and lift capacity tables. Operators must read the manual thoroughly before use to safely handle, operate and service the excavator.
Daewoo doosan dx160 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage lines, hot fluids that can cause burns, and rotating or moving parts that can cause injury.
Daewoo doosan dx140 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage electrical lines, hot fluids that can cause burns, and rotating equipment that can cause injury.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjsjjdkemmde
This document provides an operation and maintenance manual for a Doosan wheel loader model DL420. It includes safety information, descriptions of machine components and controls, operating instructions, maintenance procedures, and specifications. Operators and maintenance personnel must read and understand the entire manual before operating or servicing the machine to avoid serious injury or death.
Daewoo doosan dl300 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies locations of safety labels on the machine and warns that unauthorized modifications could create safety hazards.
- Operators and maintenance personnel are instructed to read the entire manual before use to understand all safety precautions.
Daewoo doosan dl200 tc wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using safety features properly, operating only if feeling well, and being aware of hazards inside the operator's cabin.
Daewoo doosan dl200 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using the machine as intended, following all safety procedures, and ensuring safety features like guards are in good condition.
Daewoo doosan 470 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan 460 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 460 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan 440 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 430 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Caterpillar cat 330 f l excavator (prefix wba) service repair manual (wba0000...fjsjjdkemmde
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, brake piston, rotating group, pistons, and seals. Various tools are required, including retaining ring pliers, a bearing puller, threaded rods, nuts, and washers to secure and remove parts safely. Care must be taken to avoid damage and properly release spring forces during disassembly.
Caterpillar cat 330 f l excavator (prefix lcg) service repair manual (lcg0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly including gears, shafts, housings, seals and bearings. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating and installing each part in the proper order and orientation using torque specifications where required.
Caterpillar cat 330 f l excavator (prefix kfa) service repair manual (kfa0000...fjsjjdkemmde
The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove it, a tool is used to prevent the crankshaft from rotating while the pulley assembly screws are removed with a torque socket. The assembly is then lifted off. To install it, the components are assembled in reverse order and tightened using guide studs and torque specifications are followed. The process involves up to 21 steps and requires the use of 4 tools.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix hck) service repair manual (hck0000...fjsjjdkemmde
This document provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, friction discs, and rotating group. Various tools are required, and care must be taken due to spring forces. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 330 f l excavator (prefix ght) service repair manual (ght0000...fjsjjdkemmde
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
Caterpillar cat 330 f excavator (prefix wba) service repair manual (wba00001 ...fjsjjdkemmde
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, brake piston, rotating group, pistons, and seals. Various tools are required, including retaining ring pliers, a bearing puller, threaded rods, nuts and bolts. Safety precautions are provided throughout to warn of potential spring forces or pressurized air when removing certain components.
Caterpillar cat 330 f excavator (prefix lcg) service repair manual (lcg00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly including gears, shafts, housings, seals and bearings. The assembly process describes cleaning and preparing the parts, applying sealants and lubricants, and reinstalling the parts in reverse order while precisely adjusting bearing preloads using shims. Proper torque specifications are provided for reinstalling bolts.
Caterpillar cat 330 f excavator (prefix kfa) service repair manual (kfa00001 ...fjsjjdkemmde
The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove the assembly, the alternator belt must first be removed. Torx screws are then removed using a socket while the crankshaft is prevented from rotating. The assembly can be disassembled further by removing bolts to separate the damper, pulley, and adapter. Installation follows the removal steps in reverse, including reinstalling bolts and screws while ensuring proper orientation and torque specifications are followed.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjsjjdkemmde
This document provides instructions for disassembling a travel motor on an excavator model 330F. It outlines 28 steps to completely disassemble the travel motor. The steps include removing components like the head, brake piston, rotating assembly, pistons, seals, springs, and other internal parts. Tools required include various adapters, bolts, nuts, eyebolts, retaining ring pliers, and bearing pullers to dismantle the travel motor in a safe and organized manner.
Caterpillar cat 330 f excavator (prefix ght) service repair manual (ght00001 ...fjsjjdkemmde
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
Caterpillar cat 330 d2 l excavator (prefix zbf) service repair manual (zbf000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back onto the final drive, noting that cleanliness is important and some components like O-rings must be replaced. Proper bearing preload is achieved through measuring clearance and installing shims as needed.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, housings, seals, and bearings. The assembly process similarly provides step-by-step instructions for installing the parts back into the final drive, noting that cleanliness is important and some parts like O-rings must be replaced. Proper bearing preload is achieved through measuring clearances and installing the correct thickness of shims.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Daewoo doosan 460 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 460 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan 440 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 430 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Caterpillar cat 330 f l excavator (prefix wba) service repair manual (wba0000...fjsjjdkemmde
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, brake piston, rotating group, pistons, and seals. Various tools are required, including retaining ring pliers, a bearing puller, threaded rods, nuts, and washers to secure and remove parts safely. Care must be taken to avoid damage and properly release spring forces during disassembly.
Caterpillar cat 330 f l excavator (prefix lcg) service repair manual (lcg0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly including gears, shafts, housings, seals and bearings. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating and installing each part in the proper order and orientation using torque specifications where required.
Caterpillar cat 330 f l excavator (prefix kfa) service repair manual (kfa0000...fjsjjdkemmde
The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove it, a tool is used to prevent the crankshaft from rotating while the pulley assembly screws are removed with a torque socket. The assembly is then lifted off. To install it, the components are assembled in reverse order and tightened using guide studs and torque specifications are followed. The process involves up to 21 steps and requires the use of 4 tools.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix hck) service repair manual (hck0000...fjsjjdkemmde
This document provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, friction discs, and rotating group. Various tools are required, and care must be taken due to spring forces. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 330 f l excavator (prefix ght) service repair manual (ght0000...fjsjjdkemmde
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
Caterpillar cat 330 f excavator (prefix wba) service repair manual (wba00001 ...fjsjjdkemmde
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, brake piston, rotating group, pistons, and seals. Various tools are required, including retaining ring pliers, a bearing puller, threaded rods, nuts and bolts. Safety precautions are provided throughout to warn of potential spring forces or pressurized air when removing certain components.
Caterpillar cat 330 f excavator (prefix lcg) service repair manual (lcg00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly including gears, shafts, housings, seals and bearings. The assembly process describes cleaning and preparing the parts, applying sealants and lubricants, and reinstalling the parts in reverse order while precisely adjusting bearing preloads using shims. Proper torque specifications are provided for reinstalling bolts.
Caterpillar cat 330 f excavator (prefix kfa) service repair manual (kfa00001 ...fjsjjdkemmde
The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove the assembly, the alternator belt must first be removed. Torx screws are then removed using a socket while the crankshaft is prevented from rotating. The assembly can be disassembled further by removing bolts to separate the damper, pulley, and adapter. Installation follows the removal steps in reverse, including reinstalling bolts and screws while ensuring proper orientation and torque specifications are followed.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjsjjdkemmde
This document provides instructions for disassembling a travel motor on an excavator model 330F. It outlines 28 steps to completely disassemble the travel motor. The steps include removing components like the head, brake piston, rotating assembly, pistons, seals, springs, and other internal parts. Tools required include various adapters, bolts, nuts, eyebolts, retaining ring pliers, and bearing pullers to dismantle the travel motor in a safe and organized manner.
Caterpillar cat 330 f excavator (prefix ght) service repair manual (ght00001 ...fjsjjdkemmde
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
Caterpillar cat 330 d2 l excavator (prefix zbf) service repair manual (zbf000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back onto the final drive, noting that cleanliness is important and some components like O-rings must be replaced. Proper bearing preload is achieved through measuring clearance and installing shims as needed.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, housings, seals, and bearings. The assembly process similarly provides step-by-step instructions for installing the parts back into the final drive, noting that cleanliness is important and some parts like O-rings must be replaced. Proper bearing preload is achieved through measuring clearances and installing the correct thickness of shims.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Globalfleet - global fleet survey 2021 full results
Toyota 7 fgcu20 forklift service repair manual
1. This manual covers the service procedures of the TOYOTA FORKLIFT
7FGU/7FDU15-32seriesand 7FGCU20-32series.Pleaseusethismanual
for providing quick, correct servicingof the correspondingforklift mode;&.
Thismanualdeals withthe above modelsas of October 1999.Pleaseunder-
standthat disagreementcantakeplacebetweenthedescriptionsinthemanual
and actual vehicles due to change in designand specifications. Any change
or modifications thereafter will be informed by Toyota Industrial Equipment
Parts & Service News.
For the service proceduresof the mounted engine, read the repair manuals
listedbelow as referencetogether with this manual.
(Reference)
Repair manuals relatedto this manual are as follows:
TOYOTAINDUSTRIAL EQUlPMENT4YENGINE
REPAIRMANUAL (NO. CE602-1)
TOYOTAINDUSTRIALEQUIPMENT1DZ-I1ENGINE
REPAIRMANUAL (NO. CE618-1)
TOYOTA Material Handling Company
A Division of TOYOTA INWSRIESCORPORATION
2. SECTIONINDEX
I W E 1 SECTIONI
GENERAL
ENGINE
TORQUE CONVERTER&
TRANSMISSION
PROPELLER SHAFT
DIFFERENTIAL
FRONT AXLE
REAR AXLE
STEERING
BRAKE
BODY
yI
MAST
CYLINDER
OIL PUMP
OIL CONTROL VALVE
$3
3. GENERAL
Page
EXTERIOR VIEWS ........................................................ 0-2
VEHICLEMODEL .........................................................0-3
FRAMENUMBER ...........................................................0-4
HOW TO USE THIS MANUAL ....................................0-5
EXPLANATIONMETHOD ................................................0-5
TERMINOLOGY..............................................................0-6
ABBREVIATIONS ............................................................0-6
OPERATIONAL TIPS ....................................................0-7
HOISTING THE VEHICLE...........................................0-8
ATTENTIVE POINTS ON SAS .................................... 0-8
CIRCUIT TESTER ............................................ 0-9
STANDARD BOLT & NUT TIGHTENING
TORQUE ............................................................ 0-11
BOLTSTRENGTHTYPEIDENTIFICATIONMETHOD ......0-11
TIGHTENINGTORQUETABLE ........................................0-12
PRECOAT BOLTS ........................................................0-13
HIGHPRESSURE HOSE FITTING
TIGHTENING TORQUE ............................................0-13
WIRE ROPE SUSPENSION ANGLE LIST ...............0-14
SAFE LOAD FOR EACH WlRE ROPE
SUSPENSIONANGLE............................................... 0-14
COMPONENTS WEIGHT.............................................0-15
RECOMMENDEDLUBRICANT
QUANTITY & TYPES ................................................. 0-16
LUBRICATIONCHART .................................................0-18
..........................................PERIODIC MAINTENANCE 0-19
PERIODIC REPLACEMENT OF PARTS AND
LUBRICANTS...............................................................0-25
5. 0-3
VEHICLEMODEL
Pneumatic Tire Models (Pn)
Cushion Tire Models (Cu)
Classificatron
*: USA and CANADA Only
Load Capaclty
3000 Ibs
3500 Ibs
4000 Ibs
5000 Ibs
6000 Ibs
6500 Ibs
Series
Pnl ton series
Pn2ton series
Pn3 ton series
Model
Pn15
Pn18
Pn20
-
Pn25
Pn30
Pn32
Classification
VehicleModel
7FGU15
7FDU15
7FGU18
7FDU18
7FGU20
7FDU20
7FGU25
7FDU25
7FGU30
7FDU30
*7FGU32
*7FDU32
Load Capacity
4000 Ibs
5000 Ibs
6000 Ibs
Series
Cu2ton series
Cu3ton series
Model
Cu20
Cu25
Cu30
TransmissionType
TC
TIC
T/C
TIC
TIC
TK;
TK;
TK;
TIC
T/C
T/C
T/C
Cu32 1 6500 lbs / *7FGCU32 TIC
VehicleModel
7FGCU20
7FGCU25
7FGCU30
I
4Y
Engine
TransmissionType
TIC
TIC
TIC
Gasoline
Engine
4Y
1DZ-ll
4Y
1DZ-ll
4Y
1DZ-ll
4Y
1DZ-11
4Y
1DZ-ll
4Y
1DZ-ll
4Y
4Y
4Y
Gasoline
Diesel
Gasoline
Diesel
Gasoline
Diesel
Gasoline
Diesel
Gasoline
Diesel
Gasoline
Diesel
Gasoline
Gasoline
Gasoline
6. FRAMENUMBER
Frame No. Punching Position
Pneumatictire
Cushiontire
Series
1 ton series
Engine
2 ton series
3 ton series
4Y
1DZ-ll
4Y
Vehiclemodel
7FGU15
4Y
*: EEC spec.
Punchingformat
.
7FGU18
7FDU20
7FDU25
7FGU30
2 ton series
3 ton series
7FGU18-60011
7FGU25
7FDU25-60011
7FGU32-60011
7FGU25-60011
1DZ-ll
4Y
4Y
7FDU30
7FDU32
7FGCU20
7FGCU25
7FGCU30
I
7FDU32-60011
7FGCU25-60011
I 7FGCU25@60011
7FGCU32-60011
7. HOW TO USE THIS MANUAL
EXPLANATIONMETHOD
1. Operationprocedure
(1) The operationprocedure is describedin either patternA or patternB below.
PatternA: Explanationof eachoperation stepwithillustration.
Pattern B: Explanation of operation procedure by indicating step numbers in one illustration, fol-
lowed by explanation of cautions and notes summarized as point operations.
Example of descriptionin pattern B
Step Nos. are partially sometimes
omitted in illustrations.
When a part requiring tightening
torque instructionis not indicatedin
the illustration,the part name is de-
scribed in the illustrationframe.
T= 46.1 -48.1
(470 -490)
r34.0-35.5)
8
DISASSEMBLY-INSPECTION-REASSEMBLY Tghteningtorqueunit T= N.m(kgf-cm)[ft-lbfl
DisassemblyProcedure
1 Remove the cover. [Point 11
2 Remove the bushing[Point 21 C Operation explained later
3 Remove the gear.
Point Operations Explanationof key point for operationwith an illustration
[Point 11
LL
Disassembly: Put a match mark when removing the pump cover.
[Point 21
Inspection: Measurethe bush inside diameter.
Limit: 19.12 mm(0.7528 in)
8. 2. How to read components figures (Example)
(1) Thecomponentsfigureusestheillustration
in the parts catalog for the vehicle model.
Please refer to the catalog for checkingthe
part name.
The number at the right shoulder of each
components figure indicates the Fig. num-
ber in the parts catalog.
FIGnumber inpartscatalog
3. Matters omitted inthis manual
(1) This manual omits description of the following jobs, but perform them in actual operation:
@ Cleaning and washing of removedparts as required
@ Visualinspection(partially described)
TERMINOLOGY
Caution:
lmportantmattersnegligenceof whichmaycausephysicaldamage. Be sure to observethem.
Note:
lmportant items negligence of which may cause breakage or breakdown. And operation pro-
cedure requiring special attention.
Standard: Values showing allowable range in inspection and adjustment.
Limit: Maximum or minimum allowable value in inspection or adjustment.
Abbreviation(code)
ASSY
Meaning Abbreviation(code) Meaning
Assembly
Cu Cushiontiremodels
--
LH Lefthand
SAE
SAS
SST
5-m
T =
TK;
O O T
U/S
W/
U
U C
M/T
Societyof Automotive
Engineers (USA)
System of active stability
Specialservicetool
Standard
Tighteningtorque
Torqueconverter &
transmission
Number of teeth (00)
Undersize
With
Less
Longlifecoolant
--
Manualtransmission
--
No-loadmaximum
speed
OPT
01s
Pn
PS
QFV
Option
Oversize
Pneumatic tiremodels
Power steering
4-stagemast
(Quadruple)
11. 1-3
MAJOR SPECIFICATIONS
Gasoline Engines
Diesel Engines
4Y (Pn3 ton series)
t
t
t
t
t
t
c
Gasoline :43 (58)/2600
GasolinelLPG :38 (52)/2600
LPG :40 (54)/2600
t
t
t
I 2800
Item
Engine type
Numberofcylindersanda@gpr~tent- -
. -
Combustionchambertype
Valvemechanism
Bore x stroke mm(in)
Totaldisplacement cm3(in3
)
Compressionratio
Maximumpower kW(PS)lrpm
Maximumtorque N.m (kgf-m)lrpm
Minimum specific fuel
consumption g/kW-h(g/PS-h)/rpm
Serviceweight kg(Ib)
No-load maximum rpm Tm
Note:
For 2.3 ton series 1DZ-I1 models equipped with vehicle speed control system (OPT), the spec.
figures and performance curve are same with those of 1 ton series 1DZ-II models.
Pnl.2 ton series
Cu2-3ton series
Gasolinek y c l e
lnline4 cylinders
longitudinal
Wedgetype
OHV-chaindriven
91.0 x 86.0
(3.583 x 3.386)
2237(136.51)
8.8
Gasoline :40 (54)/2400
GasolinelLPG :35 (48)/2400
LPG :37 (50)/2400
Gasoline :I62 (16.5)11800
GasolinelLPG :I47 (15.0)11600
LPG :I57 (16.0)11800
Gasoline :272 (200)/2300
GasolinelLPG :258 (190)/2400
LPG :252 (185)/2400
134 (295)
2600
Enginetype
Numberofcylindersandarrangement
Combustionchamber type
Valvemechanism
Bore x stroke mm(in)
Totaldisplacement cm3(in3
)
Compressionratio
Maximumpower kW (PS)lrpm
Maximumtorque N.m (kgf-m)lrpm
Minimum specificfuel
consumption glkW-h(g/PS-h)/rpm
Serviceweight kg (Ib)
No-loadmaximum rpm rpm
1DZ-11(Pnl ton series)
Diesel4-cycle
lnline 4cylinderslongitudinal
Whirlchamber type
OHV-geardriven
86.0 x 107.0
(3.386 x 4.213)
2486 (151.71)
21.5
40 (55)/2400
167 (17.0)/1600
252(185)/1400
162(357)
2600
1DZ-I1(Pn2-3tonseries)
t
t
t
t
C
t
t
44 (60)/2600
t
t
t
2800
12. Point Operations
[Point 11
Removal:
Put a match marks on the fuel hose and the coupler.
[Point 21
Removal:
Put a match mark on the radiator and torque converter
cooler hose.
[Point 31
Removal-Installation:
SST 09010-20111-71 -- GI
09010-23320-71 -4
Removal:
Tentatively hoist up until the mounting bolt completely
comes out from the hole in the frame.
[Point 41
Removal:
Use a straight-edge screwdriver for separation. If the fit-
ting is too tight, change the SST hook position and adjust
the engine angle for easier separation.
13. AIR BLEEDING FROM FUEL SYSTEM
(DIESEL VEHICLE)
1. Operate the hand pump of the fuel filter until the pump
operatingforce becomes heavy.
ENGINE SPEED INSPECTION AND ADJUSTMENT
Note:
Warm up the engine, set the vehicle to the following conditions, and conduct inspection and ad-
justment.
Coolant temperature: 80°C (176OF)or more, engine oil: 70°C (158'F) or more, operating oil tem-
perature: 50°C (122OF)or more, auto choke in release state (4Y engine)
B
tor
4YENGINE
Idling speed and idle up speed inspection and adjust-
ment
<Gasoline Vehicle>
1. Install the engine speedometer.
2. Disconnect the idle up actuator and inspect the idle up
speed.
Standard: 1000 a 30rpm
3. If the measured value is out of the specifiedrange, ad-
just by turning adjusting screw B.
4. Connect the idleup actuator.
5. Check the idling speed.
Standard: 800+ 5rpm
6. If the measuredvalue is out of the specified range, ad-
just by adjusting screw A.
7. If the speed is still higher after adjustment in 3 above,
adjust usingthe followingprocedure:
14. A
Regulator
(1) If the autochoke cam is contactingalthoughthe cool-
ant temperature is as specified above, replace the
auto choke.
(2) If the idle up actuator rod and adjusting screw B are
incontactwitheachother, turnadjustingscrew 6coun-
terclockwise.
<LPG/Gasolineor LPG>
1. Install the engine speedometer.
2. Disconnect the idle up actuator and inspect the idle up
speed.
Standard:
LPGIGasoline: 1000 2 30 rpm
3. Check theidlingspeed.
Standard:
LPGIGasoline: 800 :,sarpm
LPG: 800 :,50 rpm
4. If themeasuredvalueis out of the specifiedrange, make
adjustment according to the followingprocedure:
(1) Make adjustment by turning adjusting screw B (LPG
vehicle) or C (LPGIgasolinevehicle).
(Iflessthanthe standard, turnadjustingscrewAcoun-
terclockwisebeforehand.)
(2) Slowly turn adjusting screw A clockwise or counter-
clockwise until the maximum speed is obtained.
(3) Determine the positions of adjusting screws B and C
by repeating steps (1)and (2)untilthe value obtained
in step (2) satisfies the standard.
(4) Slowly turn adjusting screw A clockwiseuntil the CO
concentrationbecomes 2 to 3%, and then turn it 45
degreescounterclockwisefrom thepositionwherethe
speed begins to drop.
15. No-load Maximum Speed Inspection-Adjustment
<Gasoline, LPG or LPGlGasolineVehicle>
1. Install the engine speedometer.
2. Inspect and adjust the no-load static maximum speed.
(1) Measure thespeedwhen the acceleratorpedalis fully
depressed.
Standard:
4Y engine:
Pnl-2 ton series: ..........2600 f 50 rpm
Cu2-3ton series: ..........2600 f 50 rpm
Pn3 ton series: ............. 2800 f 50 rpm
(2) If the measured value does not satisfy the
standard,make adjustment as follows:
Remove the seal and loosen the lock bolt.
@ Fully depressthe accelerator pedal.
@ Turn the bushing for adjustment, while holding the
adjustingscrew of the air governorimmovablewith
a straight-edgescrewdriver.
3. Check and adjust relief down.
(1) Operate the tilt lever fully backward with the engine
runningat the maximum speed, and measure the de-
crease in speed (relief down) upon full relief.
Standard: Within 300 rpm
(2) If the measured value is out of the standard range,
make adjustment according to the following proce-
dure:
@ Turn the adjusting screw counterclockwise to de-
crease relief down.
@ Returnthe screwby 1110 of a turnto eliminatetwist-
ing of the spring in the air governor.
@ Adjust the no-loadmaximum speed.
@ Repeatsteps @, @and @untilthemeasuredvalue
satisfies the standard.
4. Check and adjust hunting.
(1) Check for hunting upon tilt relief at the no-load maxi-
mum speed.
(2) If hunting occurs a few times or more, make adjust-
ment according to the following procedure:
@ Turn the adjusting screw clockwise by 112 of a turn
or more.
@ Returnthe screwcounterclockwiseby 114 of a turn.
@ Finally,.tumit by 1110 of a turnto eliminatetwisting
of the spring in the air governor.
@ Adjust the no-loadmaximum speed.
@ Repeat steps @through@until hunting occurs no
more.
5. Repeat adjustmentsin steps 2 to4 until respectivestan-
dards are satisfied.
6. Seal the lock bolt.
16. 1DZ-llENGINE
Idle Speed Inspection.Adjustrnent
1. Install the engine speedometer.
2. Check the idle speed.
Standard: 750 f 25 rpm
3. If the measuredvalueis out of the standard,loosen the
locknut andmake adjustmentby turningadjustingscrew
A.
No-load Maximum Speed Inspection.Adjustment
1. Install the engine speedometer.
2. Inspect and adjust the no-load maximum speed.
(1) Measurethe speedwhen the acceleratorpedalis fully
depressed.
Standard:
1DZ-ll engine:
....................1 ton series: 2600 f 50 rpm
Vehicle speed control
..............system spec.: 2600 f 50 rpm
2.3 ton series: .................2800 f50 rpm
(2) If the measured value does not satisfy the standard,
make adjustment as follows:
@ Remove the seal and loosen the lock nut.
@ Make adjustment by turning adjusting screw B.
3. Check and adjust relief down.
(1) Operate the tilt lever fully backward with the engine
running at the maximum speed and measure the de-
crease in speed (relief down) upon full relief.
Standard: Within 200 rpm
4. Seal the adjusting screws after the end of adjustment.
18. Vehicle without
AIR CLEANER CLEANING-INSPECTION
1. Open the engine hood.
2. Remove the element.
Note: -
In case of the double element type (OPT), do not remove
the inner element for other than replacement.
3. Clean the element.
(1) For ordinarycleaning,blow with compressedair [690
kPa (7kgflcm2) [I00 psi] or less] vertically along the
pleats from the inside of the element.
If heavily contaminated, washing is possible.
(2) Element washing method
Dissolveneutraldetergentintepidwater (approx. 40°C
(104°F)) and immerse the element in it for about 30
minutes. Then, rinse the element well with clear wa-
ter. [Water pressure:275 kPa(2.8 kgflcm2
)[40 psi] or
less]
After washing, naturally dry the element or dry the
element with a dryer (cold air).
Note:
Do not damage the element during washing.
Never use compressed air or hot air for drying.
4. Clean the evacuator valve (dust discharge valve).
(7) Holdthe tip end of the evacuator valve and discharge
dust and dirt from the inside of the valve.
5. Inspect the element.
(1) After cleaning,place an electricbulbin theelement to
inspect any damage in the element. If any pinhole,
tear or damage is found, replace it witti a new ele-
ment.
6. Element replacement
Replace the elementafter it is washed six times or gen-
erally at intervals of 12 months.
7. Installthe element.
(1) Install the evacuator valve in the illustrated direction.
19. CLOGGING WARNING SYSTEM INSPECTION
1. Warning lamp inspection
(1) See thattheair cleanerwarninglampcomeson when
the ignition switch is turned ON and goes out when
the,enginestarts.
2. Individualinspection
(1) Use a mity vac to apply a negative pressure to the
vacuum switch, and inspect conduction.
Standard
Gasoline models:
2942 2 294 Pa (300 2 30 mm H20)
(22.1 f 2.2 mmHg) [11.81 f 1.18 in H,O]
[0.870 2 0.087 in Hg]: Conduction
Diesel models:
7473 f 569 Pa (762 2 58 mm H,O)
(56.0 2 4.3 mmHg) r30.00 +2.28 in H20]
[2.205 f 0.169 in Hg]: Conduction
RADIATOR
COMPONENTS
20. SPECIFICATIONS
COOLANT CAPACIN AND ANTIFREEZE TABLE Unit: e(US gal)
Type
Fin type
Coolantcapacity(inradiator)
Capopeningpressure kPa(kgflcm2
)[psi]
Others
Crossflow
Cormgatedfin
See thetablebelow
88 i 14.7 (0.9 i0.15) [13 f 2.11
Builtintorqueconvertercooler
Note:
The total amount of coolant does not include the capacity of the reservoir tank.
Reservoir tank capacity: 0.6t (0.16 US gal) (at FULL mark position)
Radiator
capacity
Total
amountof
coolant
8.5 (2.24)
8.5 (2.24)
9.6 (2.53)
9.6(2.53)
8.5 (2.24)
Pnl ton series
Pn2.3 ton series
Cu2.3 ton series
LLC mixing
ratio at 30%
(to-15OC
(5OF))
2.6 (0.69)
2.6 (0.69)
2.9 (0.77)
2.9 (0.77)
2.6 (0.69)
4Y
lDZ-Il
4Y
1DZ-II
4Y
2.7 (0.71)
2.7 (0.71)
3.7 (0.98)
3.7 (0.98)
2.7 (0.71)
LLC mixing
ratio at 50%
(to-35OC
(-31°F))
4.3 (1.14)
4.3 (1.14)
4.8 (1.27)
4.8 (1.27)
4.3 (1.14)
Antirust
mixing at
5%
0.4 (0.11)
0.4 (0.11)
0.5 (0.13)
0.5 (0.13)
0.4 (0.11)
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. MUFFLER & EXHAUST PIPE
COMPONENTS
Gasoline model 1702
1702-362A
Diesel model
(UL-DS)
1702-361A
23. Note:
The muffler can be removed by either of the two methods shown below.
@ Remove the muffler after removing the counterweight.
@ Remove the muffler after removing the radiator Wlcounterweight.
Here, method @is explained.
RemovalProcedure
1 Remove the counterweight. (See p. 9-7.)
2 Disconnect the exhaust pipe.
3 Remove the muffler Witail pipe.
4 Disconnect the tail pipe from the muffler.
Installation Procedure
The installationprocedure is the reverse of the removal procedure.
CATALYTIC MUFFLER MAINTENANCE
Replace the muffler ASSY every year (2000 hours) on either the gasoline or diesel engine vehicle.
24. BATTERY
COMPONENTS
SPECIFICATIONS
Battery type list (The battery is selected according to the equipped engine.)
1DZ-ll
STD
GR35 GR24R
(JIS55D23L) (JIS80D26L)
GR24R
(JIS80D26L)
c
55
c
19.0 (41.9)
GR35
(JIS 55D23L)
Voltage V
5-hour rate capacity Ah
Specific gravity of battery
fluidinuse (at 20°C (68°F))
Battery weight kg (Ib)
12
48
1.280
16.2 (35.7)