The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove it, a tool is used to prevent the crankshaft from rotating while the pulley assembly screws are removed with a torque socket. The assembly is then lifted off. To install it, the components are assembled in reverse order and tightened using guide studs and torque specifications are followed. The process involves up to 21 steps and requires the use of 4 tools.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018640
Rear Power Take-Off (RPTO) - Remove
SMCS - 1165-011-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If necessary, remove the OEM equipment from the rear power take-off (RPTO).
1/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g02069019
Illustration 2 g02069023
2. Remove bolts (1). Remove adapter (2) from flywheel housing (9). Remove O-ring seal (3)
(not shown).
2/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
3. Remove bolts (4). Remove adapter (5) from flywheel housing (9). Remove O-ring seal (6)
(not shown).
Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
4. Remove gear (7) from crankshaft (8).
5. If necessary, follow Steps 5.a through Steps 5.b in order to remove the sleeve bearing from
the adapter.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (2).
6. Repeat Steps 6.a through Step 6.b in order to remove the sleeve bearing from adapter (5).
a. Place adapter (5) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (5).
Illustration 3 g02069020
3/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. 7. Remove gear assembly (11) and gear assembly (12) from flywheel housing (9).
Illustration 4 g02069021
Illustration 5 g02069453
8. Remove bolts (13). Remove gear (17) and idler hub (15) from flywheel housing (9).
4/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. 9. Remove bolts (14). Remove gear (18) and idler hub (16) from flywheel housing (9).
10. If necessary, follow Steps 10.a through Steps 10.b in order to remove the sleeve bearing
from the gear.
a. Place gear (17) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19) from gear
(17).
Illustration 6 g03453499
11. Repeat Steps 11.a through Step 11.b in order to remove the sleeve bearing from the
remaining gear.
a. Place gear (18) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19a) from
gear (18).
5/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 7 g02069024
12. If necessary, follow Steps 12.a through Steps 12.b in order to remove the sleeve bearings
from the flywheel housing.
a. Use a suitable tool in order to remove sleeve bearing (20) from flywheel housing (9).
b. Repeat Step 12.a in order to remove sleeve bearing (21) from flywheel housing (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:22:20 UTC+0800 2020
6/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018641
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of the rear power take-off (RPTO) are clean and free from wear
and damage.
1/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 2 g02069024
2. If necessary, follow Steps 2.a through Steps 2.c in order to install the sleeve bearings from
the flywheel housing.
a. Accurately align oil Holes (X) in sleeve bearing (20) with the oil holes in flywheel
housing (9).
b. Use Tooling (A) in order to install sleeve bearing (20) into flywheel housing (9).
Note: Ensure that the oil holes are correctly aligned. If the oil holes are not correctly
aligned, the sleeve bearing should be removed.
c. Repeat Step 2.a through Steps 2.b in order to install sleeve bearing (21) to flywheel
housing (9).
3/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 3 g02070455
3. If necessary, follow Steps 3.a through Steps 4 in order to install the sleeve bearing to the
gears.
a. Place gear (17) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19) with Grooves (Y) in gear (17).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19) into gear
(17).
4/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 4 g03453500
4. Repeat Steps 3.a through Step 3.c in order to install the sleeve bearing to gear (18).
a. Place gear (18) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19a) with Grooves (Y) in gear (18).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19a) into gear
(18).
5/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 5 g02069021
5. Lubricate idler hub (15) and gear (17) with clean oil. Install idler hub (15) to gear (17).
Note: Ensure that the gear and the idler hub are correctly oriented.
6. Install gear (17) and idler hub (15) assembly to flywheel housing (9).
Note: Ensure that the oil hole in the idler hub is correctly positioned.
7. Install bolts (13) to idler hub (15) and hand tighten bolts.
Note: Ensure that the idler hub is correctly aligned to the flywheel housing.
8. Repeat Steps 5 through Step 7 in order to install gear (18), idler hub (16) and bolts (14) to
flywheel housing (9).
9. Tighten bolts (13) and bolts (14) to a torque of 100 N·m (74 lb ft).
10. Ensure that there is tactile backlash between gear (17) and gear (18). Ensure that there is
end play between the idler hubs and the gears.
6/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 6 g02069020
11. install gear assembly (11) and gear assembly (12) to flywheel housing (9).
7/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 8 g02070473
12. If necessary, follow Steps 12.a through Steps 12.c in order to install the sleeve bearings to
the adapters.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to install sleeve bearing (10) into
adapter (2).
c. Repeat Steps 12.a through Step 12.b in order to install the sleeve bearing into adapter
(5).
13. Install a new O-ring seal (3) (not shown) to adapter (2).
14. Install adapter (2) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
15. Install bolts (1) and tighten the bolts to a torque of 55 N·m (41 lb ft).
16. Install a new O-ring seal (6) (not shown) to adapter (5).
17. Install adapter (5) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
18. Install bolts (4) and tighten the bolts to a torque of 55 N·m (41 lb ft).
9/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 19. Ensure that there is tactile backlash between the gears. Ensure that there is end play between
the gears and the flywheel housing and the adapters.
20. Install gear (7) to crankshaft (8).
21. If necessary, install the OEM equipment to the rear power take-off (RPTO).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:23:16 UTC+0800 2020
10/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909511
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:24:11 UTC+0800 2020
3/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909517
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.f in order to install vibration damper, crankshaft
pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Remove Tooling (D) .
f. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Jul 6 09:25:07 UTC+0800 2020
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018646
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly 1
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03417117
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...