The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) An overview of the configuration of the articulating steer axle suspended from the counterweight.
2) Steps for removing the steer axle which include disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
3) Details on dismantling and reassembling wheel hubs, stub axles, and lubricating the steer axle with grease.
Husqvarna rider 11 bio service repair manualfjskedsxmmem
This document is a workshop manual that provides safety regulations, general instructions, technical specifications, maintenance procedures, and troubleshooting information for Rider 11, Rider 13, and Rider 16 ride-on lawn mowers. It includes details on the engine, steering, transmission, battery, wheels, mowing deck, and electrical systems. The manual describes maintenance tasks like checking oil levels, adjusting the mowing deck, and replacing parts like the belts, blades, and hydrostatic transmission components. Special tools required for repairs are also listed.
Husqvarna rider 14 pro service repair manualfhjsekfksemert
1. This document provides instructions and technical specifications for servicing Rider mowers, including safety guidelines, maintenance schedules, repair procedures, and diagrams.
2. Maintenance schedules are provided for pre-delivery service, 25-hour service, 50-hour service, 100-hour service, 300-hour service, and seasonal service. Tasks include oil changes, filter replacement, adjustments, inspections, and dealer servicing.
3. Repair procedures are outlined for removing and replacing parts like the engine, steering components, transmission, and mowing deck. Specifications are provided for dimensions, engine, gearbox, and controls.
Case cx460 crawler excavator service repair manualjfjkskekemm
This document provides instructions for removing and installing the engine on a CX460 Crawler Excavator. It outlines 17 steps for removal, including disconnecting electrical connections, hydraulic and fuel lines, removing mounting hardware, and lifting the engine off with suitable lifting equipment. Notes are provided on inspection of rubber mounts during installation and special torque settings. The summary also advises to reverse the removal steps for installation and perform bleeding and leak checks after installation before operating the machine.
New holland tt55 tractor service repair manualufdjjsjekkemme
This document is a repair manual for New Holland TT55 and TT75 tractors. It provides detailed instructions and specifications for overhauling various engine systems, including the engine, lubrication system, coolant system, and fuel system. The manual contains sections covering the removal and installation of the engine, disassembly and assembly procedures, inspection and repair of engine components, specifications and torque values. It is intended to guide authorized repair technicians in properly servicing and maintaining the tractor engines.
Case cx350 crawler excavator service repair manualfusfejskekem
This document provides instructions for removing and installing the engine on Case CX330 and CX350 crawler excavators. It outlines 17 steps for removing the engine, including disconnecting electrical connections, fuel lines, hydraulic pump, radiator/oil cooler assembly, and lifting the engine from the machine. When installing the engine, the steps are reversed. Safety precautions are provided, and it is noted that flexible engine mounts and retaining hardware should be inspected and replaced if needed.
Kubota l185 f tractor parts catalogue manualdikdkkdkdm
The document provides instructions for parts books, including definitions of column headings in parts number pages. It defines terms like REF.No, Part No, Description, Q'ty, S.No, I/C, and Remarks. It also notes country codes that may be included, like A for USA, CA for Canada, and FR for France. The document is meant to help understand what information is included for each part listed in a parts book.
John deere powertech 4.5 l & 6.8l diesel engines base engine service repa...dikdkkdkdm
This document provides information about Powertech 4.5L and 6.8L diesel engines, including:
- Identification of engine models and serial numbers
- Guidelines for fuels, lubricants, and coolants
- Sections covering repair and maintenance of engine components
- Theory of operation and diagnostics
- Lists of required tools and specifications
The document contains technical details to assist experienced technicians in servicing Powertech diesel engines. Safety messages are included throughout and other companion manuals provide additional information on electronic fuel systems.
Husqvarna trimmers service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
Husqvarna rider 11 bio service repair manualfjskedsxmmem
This document is a workshop manual that provides safety regulations, general instructions, technical specifications, maintenance procedures, and troubleshooting information for Rider 11, Rider 13, and Rider 16 ride-on lawn mowers. It includes details on the engine, steering, transmission, battery, wheels, mowing deck, and electrical systems. The manual describes maintenance tasks like checking oil levels, adjusting the mowing deck, and replacing parts like the belts, blades, and hydrostatic transmission components. Special tools required for repairs are also listed.
Husqvarna rider 14 pro service repair manualfhjsekfksemert
1. This document provides instructions and technical specifications for servicing Rider mowers, including safety guidelines, maintenance schedules, repair procedures, and diagrams.
2. Maintenance schedules are provided for pre-delivery service, 25-hour service, 50-hour service, 100-hour service, 300-hour service, and seasonal service. Tasks include oil changes, filter replacement, adjustments, inspections, and dealer servicing.
3. Repair procedures are outlined for removing and replacing parts like the engine, steering components, transmission, and mowing deck. Specifications are provided for dimensions, engine, gearbox, and controls.
Case cx460 crawler excavator service repair manualjfjkskekemm
This document provides instructions for removing and installing the engine on a CX460 Crawler Excavator. It outlines 17 steps for removal, including disconnecting electrical connections, hydraulic and fuel lines, removing mounting hardware, and lifting the engine off with suitable lifting equipment. Notes are provided on inspection of rubber mounts during installation and special torque settings. The summary also advises to reverse the removal steps for installation and perform bleeding and leak checks after installation before operating the machine.
New holland tt55 tractor service repair manualufdjjsjekkemme
This document is a repair manual for New Holland TT55 and TT75 tractors. It provides detailed instructions and specifications for overhauling various engine systems, including the engine, lubrication system, coolant system, and fuel system. The manual contains sections covering the removal and installation of the engine, disassembly and assembly procedures, inspection and repair of engine components, specifications and torque values. It is intended to guide authorized repair technicians in properly servicing and maintaining the tractor engines.
Case cx350 crawler excavator service repair manualfusfejskekem
This document provides instructions for removing and installing the engine on Case CX330 and CX350 crawler excavators. It outlines 17 steps for removing the engine, including disconnecting electrical connections, fuel lines, hydraulic pump, radiator/oil cooler assembly, and lifting the engine from the machine. When installing the engine, the steps are reversed. Safety precautions are provided, and it is noted that flexible engine mounts and retaining hardware should be inspected and replaced if needed.
Kubota l185 f tractor parts catalogue manualdikdkkdkdm
The document provides instructions for parts books, including definitions of column headings in parts number pages. It defines terms like REF.No, Part No, Description, Q'ty, S.No, I/C, and Remarks. It also notes country codes that may be included, like A for USA, CA for Canada, and FR for France. The document is meant to help understand what information is included for each part listed in a parts book.
John deere powertech 4.5 l & 6.8l diesel engines base engine service repa...dikdkkdkdm
This document provides information about Powertech 4.5L and 6.8L diesel engines, including:
- Identification of engine models and serial numbers
- Guidelines for fuels, lubricants, and coolants
- Sections covering repair and maintenance of engine components
- Theory of operation and diagnostics
- Lists of required tools and specifications
The document contains technical details to assist experienced technicians in servicing Powertech diesel engines. Safety messages are included throughout and other companion manuals provide additional information on electronic fuel systems.
Husqvarna trimmers service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
Husqvarna rider 16 h service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 14 pro service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 13 h service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 13 h bio service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 11 service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 11 bio service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna pruning saws service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety recommendations when working on starters. It then provides step-by-step instructions for dismantling and assembling starters for different models, including the models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Special tools required for some procedures are also noted.
Husqvarna ice drills service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety recommendations when working on starters. It then provides step-by-step instructions for dismantling and assembling starters for different models, including the models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Special tools required for some procedures are also noted.
Husqvarna hedge trimmers service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general recommendations for working safely and properly with starters. It then provides step-by-step instructions for dismantling and assembling starters for specific models, including releasing spring tension, removing starter pulleys and springs, checking components for wear, and replacing parts. Special tools are noted where needed and safety warnings are highlighted.
Husqvarna brush cutters service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
Still r70 80 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes:
- Tire sizes and pressures for front and rear wheels
- Torque specifications for tightening lug nuts
- Instructions for removing and installing wheel hubs and bearings
- Greasing points and specifications for greasing the steering axle
Still r70 70 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes:
- Tire sizes and pressures for front and rear wheels
- Torque specifications for tightening lug nuts
- Instructions for removing and installing wheel hubs and bearings
- Greasing points and specifications for greasing the steering axle
Still r70 60 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes torque specifications for tightening lug nuts, tire sizes and pressures, and instructions for removing and mounting wheel assemblies. Front wheel lug nuts are torqued to 460 Nm, rear wheels use 460 Nm on fronts and 406 Nm on rears. Tire sizes are 125/70 R15 for front wheels and 155/80 R15 for rear wheels, inflated to 2.8-3.2 bar. Removing a wheel requires loosening lug nuts and removing the hub, bearings and seals. Reinstallation is the reverse process.
Still r70 45 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) How to remove the steer axle by disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
2) Details on dismantling and reassembling the wheel hub, including bearing and seal replacement.
3) Instructions for adjusting the wheel angle stops to set the steering angles.
4) Steps for removing and reinstalling the stub axles and internal components like bearings, seals, and king pins.
5) A description of lubricating the steer axle by applying grease fittings.
6
Still r70 30 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) An overview of the configuration of the articulating steer axle suspended from the counterweight.
2) Steps for removing the steer axle which include disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
3) Details on dismantling and reassembling wheel hubs, stub axles, and lubricating the steer axle with grease.
Still r70 20 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) How to remove the steer axle by disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
2) Details on dismantling and reassembling the wheel hub, including bearing and seal replacement.
3) Instructions for adjusting the wheel angle stops to set the steering angles.
4) Steps for removing and reinstalling the stub axles and internal components like bearings, seals, and king pins.
5) A note to lubricate the steer axle fittings with grease during steering operations.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Husqvarna rider 16 h service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 14 pro service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 13 h service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 13 h bio service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 11 service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna rider 11 bio service repair manualdikdkkdkdm
This document provides technical specifications and repair instructions for various ride-on mower models. It includes sections on safety regulations, general instructions, technical data, maintenance schedules, design and function, and reparation instructions. Technical data includes dimensions, engine specifications, gearbox information, tightening moments, and control point tolerances. Repair instructions cover procedures such as removing and replacing the engine, transmission maintenance, adjusting the mowing deck, and troubleshooting.
Husqvarna pruning saws service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety recommendations when working on starters. It then provides step-by-step instructions for dismantling and assembling starters for different models, including the models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Special tools required for some procedures are also noted.
Husqvarna ice drills service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety recommendations when working on starters. It then provides step-by-step instructions for dismantling and assembling starters for different models, including the models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Special tools required for some procedures are also noted.
Husqvarna hedge trimmers service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general recommendations for working safely and properly with starters. It then provides step-by-step instructions for dismantling and assembling starters for specific models, including releasing spring tension, removing starter pulleys and springs, checking components for wear, and replacing parts. Special tools are noted where needed and safety warnings are highlighted.
Husqvarna brush cutters service repair manualdikdkkdkdm
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
The document provides instructions for dismantling and assembling starters for various brush cutter and trimmer models. It begins with general safety warnings and recommendations. It then provides step-by-step instructions for dismantling and assembling starters for different models including the Models 265, 250/252, 240/245, 225, 232, 235, 240, 322, 325, 122, 32, Mondo, 18H, 140B and 141B. Instructions include releasing spring tension, removing starter pulleys and springs, checking parts for wear, fitting new springs and cords, and tensioning the return spring.
Still r70 80 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes:
- Tire sizes and pressures for front and rear wheels
- Torque specifications for tightening lug nuts
- Instructions for removing and installing wheel hubs and bearings
- Greasing points and specifications for greasing the steering axle
Still r70 70 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes:
- Tire sizes and pressures for front and rear wheels
- Torque specifications for tightening lug nuts
- Instructions for removing and installing wheel hubs and bearings
- Greasing points and specifications for greasing the steering axle
Still r70 60 diesel fork truck service repair manualdikdkkdkdm
The document provides specifications and maintenance instructions for wheels and tires of a forklift. It includes torque specifications for tightening lug nuts, tire sizes and pressures, and instructions for removing and mounting wheel assemblies. Front wheel lug nuts are torqued to 460 Nm, rear wheels use 460 Nm on fronts and 406 Nm on rears. Tire sizes are 125/70 R15 for front wheels and 155/80 R15 for rear wheels, inflated to 2.8-3.2 bar. Removing a wheel requires loosening lug nuts and removing the hub, bearings and seals. Reinstallation is the reverse process.
Still r70 45 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) How to remove the steer axle by disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
2) Details on dismantling and reassembling the wheel hub, including bearing and seal replacement.
3) Instructions for adjusting the wheel angle stops to set the steering angles.
4) Steps for removing and reinstalling the stub axles and internal components like bearings, seals, and king pins.
5) A description of lubricating the steer axle by applying grease fittings.
6
Still r70 30 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) An overview of the configuration of the articulating steer axle suspended from the counterweight.
2) Steps for removing the steer axle which include disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
3) Details on dismantling and reassembling wheel hubs, stub axles, and lubricating the steer axle with grease.
Still r70 20 fork truck service repair manualdikdkkdkdm
The document provides instructions for removing and installing the steer axle on a forklift truck. It includes:
1) How to remove the steer axle by disconnecting hydraulic connections, removing mounting bolts, and sliding the axle out on a hand pallet truck.
2) Details on dismantling and reassembling the wheel hub, including bearing and seal replacement.
3) Instructions for adjusting the wheel angle stops to set the steering angles.
4) Steps for removing and reinstalling the stub axles and internal components like bearings, seals, and king pins.
5) A note to lubricate the steer axle fittings with grease during steering operations.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. 01
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Chassis Frame and Counterweight
01
STILL GmbH Stand: 2/1995 ( Ersatz für Stand: )
1
2
3
4
Chassis Frame
The chassis frame is constructed of electrically
welded steel plate.
Detachable fuel and hydraulic oil tanks are
mounted inside left-hand and right-hand frame
sections respectively for extra protection.
Counterweight
The removable rear counterweight is secured to the
frame weldment by 4 bolts.
1 = hex hd bolt M24x130, 8.8 DIN 933
Torque loading: 710 Nm
2 = lock ring
3 = spherical washer C 25 DIN 6319
4 = ball cup D 28 DIN 6319
Weight of the counterweight
7032/7038 = 1,170 kg
7033/7039 = 1,514 kg
7034/7040 = 1,915 kg
7048 = 1,985 kg
7049 = 2,395 kg
7050 = 2,715 kg
3. 01
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Driver’s cab
02
STILL GmbH Stand: 2/1995 ( Ersatz für Stand: )
Bolted to the frame at the front end and to the
counterweight at the rear, the cab is mounted at 4
points on rubber type anti-vibration mounts.
Removal
- Remove panel from front cowl
- Remove floor plate
- Remove upswept type exhaust pipe (if fitted)
- Remove cover plates left and right of inspec-
tion plate, giving access to the rear rubber
mounts (above counterweight)
- Disconnect the 3 connectors at the steering
column (Fig. 1, page 3)
- Disconnect the wiring harness from the steer-
ing column
- Remove the screws which secure steering
column to hand pump (steering wheel opera-
ted pump) - Fig. 1, page 3)
- Disconnect the connections on warning horn,
brake fluid reservoir and master cylinder,
located in the front cowl (Fig. 2, page 3)
1 = rubber type anti-vibration mount
2 = allen screw M10 x 80, 8.8
3 = washer
4 = hex nut; welded to the support
4. 01
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Driver’s cab
03
STILL GmbH Stand: 2/1995 ( Ersatz für Stand: )
Driver’s cab (removal)
Detach earthing or ground connection
Remove panel to which is mounted the electronic
control unit inside front cowl
Disconnect brake line at master cylinder (Figure 2).
Refit fluid passage bolt to prevent brake fluid from
flowing out
Remove M10 x 80 allen screws front and rear
Slig cab using an overhead hoist or remove cab with
the aid of a second lift truck
5. 02
Steer axle
1
Contents Page
Technical Data for 1
Maintenance Service
Mechanical configuration of Steer axle
Steer axle removal 2
Steer axle installation 2
Wheel hub - Removal and 3
Dismantling
Wheel hub - Reassembling and 3
Installation
Wheel angle stop adjustment 4
Checking the steering angles 4
Stub axle - Removal and 5
Dismantling
Stub axle - Reassembling and 6
Installation
Lubricating the steer axle with 6
grease
Track rod removal 7
Track rod installation 7
Steer cylinder removal 8
Steer cylinder installation 8
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
6. 02
Technical Data for Maintenance Service
3
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
2
0
p
u
o
r
G
l
a
n
o
i
t
c
n
u
F
e
l
x
a
r
e
e
t
S
e
l
g
n
a
k
c
o
l
l
e
e
h
W °
2
8
-
0
8
n
i
-
e
o
T m
m
1
±
0
r
e
b
m
a
c
l
e
e
h
W °
0
l
i
a
r
T °
0
r
o
f
s
g
n
i
d
a
o
l
e
u
q
r
o
T
0
4
-
8
3
/
4
3
-
2
3
0
7
b
u
h
l
e
e
h
W m
N
5
2
2
=
A
M
g
n
i
x
i
f
e
l
x
A m
N
5
9
1
=
A
M
s
t
u
n
l
e
e
h
W m
N
5
2
4
=
A
M
r
o
f
s
g
n
i
d
a
o
l
e
u
q
r
o
T
0
5
-
8
4
0
7
b
u
h
l
e
e
h
W m
N
0
7
4
=
A
M
g
n
i
x
i
f
e
l
x
A m
N
5
9
1
=
A
M
s
t
u
n
l
e
e
h
W m
N
0
4
6
=
A
M
s
t
n
a
c
i
r
b
u
L
s
g
n
i
r
a
e
b
b
u
h
l
e
e
h
W m
u
i
h
t
i
l
0
2
-
K
2
P
K
-
5
2
8
1
5
N
I
D
o
t
F
e
s
a
e
r
G
d
e
s
a
b
p
a
o
s
m
u
i
h
t
i
l
,
0
3
-
K
2
P
K
-
5
2
8
1
5
N
I
D
o
t
F
e
s
a
e
r
G
d
e
s
a
b
p
a
o
s
s
g
n
i
r
a
e
b
e
l
x
a
b
u
t
S ,
0
2
-
N
2
F
P
K
-
5
2
8
1
5
N
I
D
o
t
L
F
e
s
a
e
r
G
d
e
s
a
b
p
a
o
s
m
u
i
h
t
i
l
9
5
6
8
4
1
.
o
N
t
n
e
d
I
L
L
I
T
S
7. 02
Steer axle
4
Configuration of steer axle
The articulating steer axle suspended from the
counterweight is mounted in 2 neoprene blocks. The
stub axles are supported in the axle beam on tapered
roller bearings. Steering is limited by stop screws on
the stub axles.
1 axle beam
2+3 fixing plates
4 Tension sleeve (depending on design)
5 Washer (depending on design)
6 Lock ring
7 socket head screw
8 neoprene blocks
Steer axle removal
CAUTION: Remove steer axle only with mast in
position on the truck!
Risk of tipping!
- Apply the parking brake.
-Securely chock the front wheels to prevent
rolling of the truck.
- Slacken steer wheel nuts.
- Jack up rear of the truck at counterweight (x)
and place wooden blocks under the counter-
weight in front of the axle.
- Remove wheels.
- Disconnect the hydraulic connections at steer
cylinder.
CAUTION: Prepare for oil spillage when
disconnecting the hydraulic connections!
Catch oil in a pan of adequate capacity
and dispose of the used oil in accordance
with laws and regulations.
- Remove the 4 socket head screws which re-
tain the steer axle in place.
- Slide a hand pallet truck under the steer axle
with wooden blocks placed on the fork ends
of the hand pallet truck.
- Using a lever, drive steer axle out of roll pins
and lower the axle onto the hand pallet truck.
Steer axle installation
- Reverse the removal procedure.
- The slots of the roll pins must face the direc-
tion of forward travel.
-Torque the 4 socket heads to: MA
= 195 Nm
CAUTION: Do not swap hydraulic connec-
tions left and right!
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
8. 1
2
3
4
6
5
9
10
7
8
11
12
02
Steer axle
5
Wheel hub - Removal and Dismantling
1 axle beam
2 stub axle
3 radial sealing ring
4 tapered roller bearing
5 wheel hub
6 roll pin
7 hub cap
8 nut
9 washer
10 tapered roller bearing
11 wheel bolt
12 ball seat nut
- Slacken ball seat nuts (12) and remove
wheel.
- Pull hub cap (7) from wheel.
- Slacken nut (8)
- Remove washer (9) with roll pin (6).
- Withdraw the hub.
- Remove radial sealing ring (3) then remove
tapered roller bearings (4) and (10) from hub.
- If necessary, drive out of wheel hub outer
races of tapered roller bearings (4) and (10).
Wheel hub - Reassembling and Installation
- Apply a smear of grease to the sealing lips of
the radial sealing ring.
- Before re-assembling the hub, repack with
grease F: cavity between inner race and
bearing cage of tapered roller bearings, and
the bearing spaces identified by an ‘x’ on the
drawing.
- To reassemble the hubs, reverse theprocedure.
- Tighten nut (8) while rotating the wheel hub.
Torque loading:
7032 - 34 / 38- 40 MA
= 225 Nm
7048 - 50 MA
= 470 Nm
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
9. Linkskurve
= 82° +0/-2 Lenkeinschlag
Rechtskurve
1
Checking the steering angles
The steering angle a must amount to 80° - 82°.
To facilitate the measurement use the complementary
angle b for the setting. It should amount to 98° - 100°.
IMPORTANT: Ensure that the wheel lock is
limited by the stop screws (1) and not by the
cylinder stroke.
Wheel angle stop adjustment
The wheel stop angle is limited by the stop
screws (1).
- By operating on stop screws (1), set both
steering angles to 80° - 82°.
- Check opposite angles.
- Checkfor adequate clearance between wheels
and truck frame.
- Check that the wheel lock is not limited by
the cylinder stroke.
02
Steer axle
6
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Right-hand bend
Left-hand bend
steering lock
10. 4
5
6
7
8
9
11
10
12
1
2
3
13
14
15
16
02
Steer axle
7
Stub axle - Removal and Dismantling
1 nut
2 washer
3 king pin
4 plug
5 stub axle
6 hex. hd. screw
7 nut
8 spacing washer
9 wiper ring
10 tapered roller bearing
11 spacer
12 grease nipple
13 tapered roller bearing
14 wiper ring
15 O-Ring
16 spacing washer
- Remove the wheel.
- Press out the pin located between track rod
and stub axle.
- Slacken nut (1).
- Remove washer (2).
- Press the king pin (3) down through the stub
axle and remove the king pin.
- Remove the stub axle from the axle.
- Remove from the stub axle: spacing
washers, ‘O’ ring, wiper rings, tapered roller
bearings and spacer (items 8-16).
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
11. 1
2
3
12
14
5
4
8
7
6
10
11
13
9
Stub axle - Reassembling and Installation
1 nut
2 washer
3 king pin
4 plug
5 stub axle
6 spacing washer
7 wiper ring
8 tapered roller bearing
9 spacer
10 tapered roller bearing
11 wiper ring
12 O-Ring
13 spacing washer
14 pin
- Insert spacer (9) into the stub axle.
- Install both tapered roller bearings (8 & 10)
after having first repacked them with a
sufficient amount of FL grade grease!
- Apply a smear of FL grade grease to the
sealing lips of the wiper rings (7 & 11).
- Install wiper rings (7 & 11), ‘O’ ring (11) as well
as both spacing washers (items 13 & 6).
- Install the stub axle into the axle beam.
- Drive in the king pin (3) from below after having
first applied a light smear of oil to it.
- Fit the washer (2) into position on the king
pin.
- Install a new nut (1) and tighten to a torque of:
MA
= 290 Nm (7032-34/38-40)
MA
= 310 Nm (7048-50)
- Press the pin (14) into the track rod and secure
with roll pins.
- Install wheel.
- Lubricate the steer axle with FL grade grease.
Lubricating the steer axle with grease
- Operate the linkage during steering.
- Using a grease gun, lubricate with FL grade
grease the fittings with which the steer axle is
equipped until a small amount of fresh grease
oozes out at the lubricating points.
02
Steer axle
8
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
12. 3
4
4
5
02
Steer axle
9
Track rod removal
The steer axle is fitted with two track rods arranged
between the steering cylinder and the two stub axles.
1 stub axle
2 piston rod
3 sealing rings
4 roll pins
5 pin
6 track rod
7 ball joint
- Remove the roll pins (4).
- Using a press, press out the pins (5).
Track rod installation
- Reverse the removal procedure.
Install pins cylinder end with a maximum press
force of
max. 21 kN
and pins stub axle end with a maximum press
force of
max. 26 kN
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
13. Steering cylinder removal
– Remove track rods.
– Disconnect hydraulic connections after
having marked them for identification.
WARNING: Hydraulic oil may spill when
disconnecting lines; be prepared
for oil spillage!
– Slacken the four fixing screws (1). .
Steering cylinder installation
– Retighten the fixing screws (1).
Torque loading:
MA
= 210 Nm (7032-34/38-40)
MA
= 295 Nm (7048-50)
– Reconnect hydraulic connections.
CAUTION:
Do not swap hydraulic connections!
– Install track rods.
NOTE: For steering cylinder dismantling and
reassembling refer to F.G. 06.
Lubricating the steer axle with grease
– Operate the linkage during greasing while the
steer axle is off load.
– Using a grease gun, lubricate with FL grade
grease the 8 fittings with which the steer axle
is equipped until a small amount of fresh
grease oozes out at the lubricating points.
NOTE: When lubricating the upper bearing, the
grease need not ooze out of the upper sealing
ring, it may also escape from the bottom.
02
Steer axle
10
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
14. 03
Power Axle
01
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Contents Page
Technical Data for Maintenance Service 1
Power AxIe / Description 2
Spur-type reduction gearbox/
Sectional view 3+4
PowAxIe removal and installation 5
Toothed hollow shaft / Sectional view 6
Toothed hollow shaft / Adjusting instructions 7
Wheel hub removel and installation 8
Half-shaft removal and installation 9
15. 03
02
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Technical Data for Maintenance Service
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Functional Group 03
Power axIe type AE 25 - 02
Toque loadings frame / power axle MA= 640 Nm
Torque loadings axIe housing / gead reduction box MA = 295 Nm
Toothed hollow shaft
End play + 0,03 mm
- 0,06 mm
Torque loadings centring flage / wheel hub ZS M 6 X 16 10-9 MA = 14 Nm
Torque loadings brake backplate / axIe housing SKS M 12 X 30 10-9 MA = 110 Nm
Torque loadings half shaft ZS M 10 X 30 10-9 MA = 69 Nm
Gearbox oil capacity: approx. 3,75 litres
grade SAE - 90 EP - 61512
Grade of grease lithium soap based grease
16. 03
03
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Description
The power axle consists of a double reduction spur-
type gearbox (1) comprising differential assembly with
two- bearing driving pinion, to which a D.C. electric
motor (2) is flange mounted, as well as of a long axle
housing (3) and an axle housing which is an integral
part of the gear case (1).
1 = différential gear reduction box
2 = D.C. drive motor
3 = long half-shaft housing to which the
brake backplate is bolted
4 = fixing screws
5 : short half-shaft housing / gearbox half to
which the brake backplate is bolted
6 = mast pivot locating points
The long axle housing (3) with the double reduction
spur- type gearbox (1) are rigidly bolted to the frame
and the mast pivots are bolted to the half-shaft
housings.
17. 03
04
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Drive motor
half shaft half shaft
Spur-type reduction gearbox with differential assembly
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
18. 03
05
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
1 Gearcase
2
3 dowel pin
4 allen screw
5 tapered roller bearing
6 dif ferential
7 gear
8 roll pin
9 hex hd bolt
10 shim 100 X 115 X 0,5 -0,8
11 tapered roller bearing
12 gear with shaft
13 shim 60 X 72 X 0,6 -0,8
14 circlip
15 connector
16 sealing ring
17 oil drain plug
18 lid
19 plug
20 Idriving dog
21 chevron seal
22 tapered roller bearing
23 toothed hollow shaft
24 ‘O’ring
25 shim 68 X 58 X 0,1 +0,5
26 ‘O’ring
27 chevron seal
28 cover
29 spring washer
30 hex hd bolt M 8 X 20 8.8
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
Spur-type reduction gearbox with dfferential assembly
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 03
06
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Power Axle removal
Remove mast assembly
Chock truck securely to prevent rolling
Drain oil at oil drain plug (2); catch oil in pan
Slacken wheelnuts Remove wheels
Clearly mark the electric cables before disconnecting
them from the drive motor
Disconnect hydraulic brake lines at brake master
cylinder
Disconnect brake cables at the parking brake
With sling around power axle attach chain to overhead
hoist
Remove mounting boits (3) right and left
Carefully manoeuvre the power axle clear of truck
Power Axle rnounting
With the overhead hoist manoeuvre power axle into f
rame
Insert the 14 mounting bolts with their 14 washers
but do not tighten at this stage
Torque all mounting bolts (3) to MA
= 640 Nm
Remove overhead hoist
Reconnect drive motor cables
Reconnect hydraulic brake lines to brake master
cylinder
Reconnect brake cables to parking brake
Install wheels
Install mast
Checking oil level:
Unscrew dipstick, push it in as far as it will go and
then withdraw again (do not screw in for checking the
oil level)
Oil capacity: 3,75 litres
Gearbox oil: SAE 90 EP - 51512
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
1 = Oil f iller neck with dipstick
2 = Oil drain plug
3 = Mounting bolts
4 = Tension washers
21. 03
07
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Item Description
1 Spring washer DIN 137
2 Hex hd bolt M 6 X 20 8.8
3 Washer 68 X 58 X 0.5
4 Chevron seal A40 X 55 X 7 - P 70
5 ‘O’ring seal 32 X 2 - P 70
6 Tapered roller bearing 32008 X - CL 7A
7 ‘0’ ring seal 65 X 3 - P 90
8 Cover
9 Allen screw M 12 X 35 10.9 MA 120 Nm
10 Lid 32,2 X 11
11 Tapered roller bearing 32008 X - CL 7A
12 Toothed hollow shaft
Power from the drive motor is transmitted via a shaft
with spline to the double reduction gears. The pinion
shaft in gearbox is supported both sides on tapered
roller bearings, and the sealing between drive motor
and gearbox is with chevron seal.
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50
22. 03
08
STILL GmbH Stand: 4/2002 ( Ersatz für Stand: )
Arbre creux à denture = A
Adjusting instructions for supportîng the toothed
hollow shaft on taper rollier bearings.
1. Assemble both taper roller bearings onto toothed
hollow shaft. After that determine dimension „A“
across tapper roller bearing outer races.
2. Determine installation demension „B“.
3. Determine centring collar length „C“ on cover.
4. Thickness of shims D = B - (minus) (A + C + 0,06
mm)
5. Add or remove shims as per actual dimension =
„D“ + (plus) 0,03 mm (pree-load) up to - (minus)
0,06 mm (free play).
6. Assemble both taper roller bearings which must
be repacked with grease up to half of the max.
capacity. In exceptional cases gearbox oil SAE
140 EP can be used as a substitute.
7. Using a fitting tool (mandrel), pre-assemble outer
race of taper roller bearing (opposite the cover).
8. Install toothed hollow shaft.
9. Using a fitting tool, pre-assemble by. around 20
mm outer race of taper roller bearing (cover side).
10.Install layer of shims as per para. 5, and by
tightening the cover bolts evenly i * n corner
to corner sequence bring taper roller
bearing outer race into final position.
Power Axle
Workshop Manual 7032 - 34 / 38 - 40 / 48 - 50