SPS HCS2 Heat Shrink Cable Glands 7-17mm
•
0 likes•116 views
The document describes a line of heat shrink cable entry glands made by Shrink Polymer Systems. The glands are available in six sizes to seal cables from 4mm to 70mm in diameter. They provide a watertight seal and secure fixing to electrical boxes. The flame retardant glands have been approved for use on high voltage cables by several UK electricity companies.
Report
Share
Report
Share
Download to read offline
Recommended
Tenby Earth Clamps
This document introduces the Tenby® Rapid Clamp Ultra, a new type of earth clamp that creates reliable earthing connections faster than traditional clamps through a simple twist fixing method. The clamp grips pipes securely in one hand without additional tools. It is suitable for both new and existing residential and commercial installations. The clamp conforms to British Standard BS 951:2009 and is available in three sizes to connect earth conductors to pipes ranging from 10-32mm in diameter.
Erico Rebar Clamps
The document describes heavy-duty rebar clamps for bonding rebar into grounding systems. The ERITECH RC70/RC100 clamps feature bronze alloy construction, provide two connection points to the rebar as required by some jurisdictions, and are easy to install. They meet the 2005 NEC standard and bond reinforcing bars and other metal structures to the grounding system.
WT Henley ABC Distribution Boxes
This document provides information about an ABC Distribution Box for overhead distribution. The box is designed to accept incoming conductors up to 120mm2 and distribute power to 9 service cables up to 35mm2. It has fully shrouded and identified terminals. The hinged door can be padlocked for security and is fitted with a stay arm. The box is designed to prevent unauthorized connections and meets various safety and ingress protection standards. It is made of flame retardant glass filled nylon and is suitable for wall or pole mounting.
Filoform branch cable joints
The Filoform range of cast resin Branch Joints are approved for use with armored and unarmored cables up to 1kv. The joints can be used with most cable types including PILC, XLPE, PVC and EPR. Standard Branch Joints can be upgraded to suit 3.3kv cables using a supplementary kit. The joints feature a hydrolysis resistant polyurethane resin in a transparent two-component bag and are fully waterproof with easy installation.
SPS Heat Shrink Cable Joints & Terminations 11kV Triplex - Selection Guide
SPS Heat Shrink Cable Joints & Terminations 11kV Triplex - Selection GuideThorne & Derrick International
This document provides product information for triplex cable terminations, joints, and accessories from Shrink Polymer Systems. It lists indoor and outdoor cable termination parts for different cable ranges from 95-300mm2. It also lists heat shrink joints, heat shrink/resin combination joints, and notes that cold shrink versions and bushing protection boots are available. Mechanical lugs, ferrules, cable preparation tools, and trifurcating joints are also offered.Explosion Proof Cable Glands - Prysmian Barrier Glands (424TX) for SWB Steel ...
Explosion Proof Cable Glands - Prysmian Barrier Glands (424TX) for SWB Steel ...Thorne & Derrick International
The 424TX Series brass barrier gland is certified for use in hazardous areas. It provides an IP66 seal for wire braided cables and can be used in Zone 1, Zone 2, and other hazardous areas. The gland is weatherproof, waterproof, and available in various thread sizes and cable diameter ranges to suit a wide variety of applications.FurseWELD Exothermic Welding Systems, Joints & Moulds from ABB Thomas & Betts
FurseWELD Exothermic Welding Systems, Joints & Moulds from ABB Thomas & BettsThorne & Derrick International
The document provides information on the FurseWELD exothermic welding system. It describes the FurseWELD process as using a self-contained reaction of copper oxide and aluminum powders to form permanent electrical connections. The system requires no external power, creates high quality connections, and can be used safely with minimal training. Tables are included to help select the appropriate joint type and materials for different conductor sizes and applications.WT HenleyMulti Way Service Heads 240/415V
This document describes a range of multiway service heads for supplying electricity to multi-occupancy properties. The service heads come in 7, 10, 16, or 24 configurations and provide a safe and reliable means of distributing power through subdivided properties like apartment buildings. They feature fuse protection, connections by socket screws for easy wiring, and dimensions varying by configuration.
Recommended
Tenby Earth Clamps
This document introduces the Tenby® Rapid Clamp Ultra, a new type of earth clamp that creates reliable earthing connections faster than traditional clamps through a simple twist fixing method. The clamp grips pipes securely in one hand without additional tools. It is suitable for both new and existing residential and commercial installations. The clamp conforms to British Standard BS 951:2009 and is available in three sizes to connect earth conductors to pipes ranging from 10-32mm in diameter.
Erico Rebar Clamps
The document describes heavy-duty rebar clamps for bonding rebar into grounding systems. The ERITECH RC70/RC100 clamps feature bronze alloy construction, provide two connection points to the rebar as required by some jurisdictions, and are easy to install. They meet the 2005 NEC standard and bond reinforcing bars and other metal structures to the grounding system.
WT Henley ABC Distribution Boxes
This document provides information about an ABC Distribution Box for overhead distribution. The box is designed to accept incoming conductors up to 120mm2 and distribute power to 9 service cables up to 35mm2. It has fully shrouded and identified terminals. The hinged door can be padlocked for security and is fitted with a stay arm. The box is designed to prevent unauthorized connections and meets various safety and ingress protection standards. It is made of flame retardant glass filled nylon and is suitable for wall or pole mounting.
Filoform branch cable joints
The Filoform range of cast resin Branch Joints are approved for use with armored and unarmored cables up to 1kv. The joints can be used with most cable types including PILC, XLPE, PVC and EPR. Standard Branch Joints can be upgraded to suit 3.3kv cables using a supplementary kit. The joints feature a hydrolysis resistant polyurethane resin in a transparent two-component bag and are fully waterproof with easy installation.
SPS Heat Shrink Cable Joints & Terminations 11kV Triplex - Selection Guide
SPS Heat Shrink Cable Joints & Terminations 11kV Triplex - Selection GuideThorne & Derrick International
This document provides product information for triplex cable terminations, joints, and accessories from Shrink Polymer Systems. It lists indoor and outdoor cable termination parts for different cable ranges from 95-300mm2. It also lists heat shrink joints, heat shrink/resin combination joints, and notes that cold shrink versions and bushing protection boots are available. Mechanical lugs, ferrules, cable preparation tools, and trifurcating joints are also offered.Explosion Proof Cable Glands - Prysmian Barrier Glands (424TX) for SWB Steel ...
Explosion Proof Cable Glands - Prysmian Barrier Glands (424TX) for SWB Steel ...Thorne & Derrick International
The 424TX Series brass barrier gland is certified for use in hazardous areas. It provides an IP66 seal for wire braided cables and can be used in Zone 1, Zone 2, and other hazardous areas. The gland is weatherproof, waterproof, and available in various thread sizes and cable diameter ranges to suit a wide variety of applications.FurseWELD Exothermic Welding Systems, Joints & Moulds from ABB Thomas & Betts
FurseWELD Exothermic Welding Systems, Joints & Moulds from ABB Thomas & BettsThorne & Derrick International
The document provides information on the FurseWELD exothermic welding system. It describes the FurseWELD process as using a self-contained reaction of copper oxide and aluminum powders to form permanent electrical connections. The system requires no external power, creates high quality connections, and can be used safely with minimal training. Tables are included to help select the appropriate joint type and materials for different conductor sizes and applications.WT HenleyMulti Way Service Heads 240/415V
This document describes a range of multiway service heads for supplying electricity to multi-occupancy properties. The service heads come in 7, 10, 16, or 24 configurations and provide a safe and reliable means of distributing power through subdivided properties like apartment buildings. They feature fuse protection, connections by socket screws for easy wiring, and dimensions varying by configuration.
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...Thorne & Derrick International
This document provides information on heat shrink joints for low voltage cables produced by Shrink Polymer Systems. It lists various joint part numbers for joining single core and multicore XLPE, PVC, PILC and transition cables with voltage ratings from 600/1000V to 3.3kV. The joints are intended for underground use and comprise adhesive lined tubes, armour supports, clamps and heat shrink outer tubes to meet BS6910-1 standards with unlimited shelf life. Thousands of these joints have been installed in critical infrastructure projects worldwide.Charles Endirect Street Lighting Equipment
Charles Endirect Ltd (CEL) is a leading UK manufacturer of street lighting equipment located in Somerset. CEL produces isolators, cut outs, feeder pillars, distribution boards, and pre-wired pillars. The company was formed in 1985 through the merger of two family businesses and has grown to serve local authorities, highways agencies, and rail networks across the UK, Ireland, and internationally. CEL is committed to innovation, high quality, and excellent customer service.
Centriforce Utility Protection Brochure
Stokbord and Tapetile cable protection systems provide durable, impact-resistant, and cost-effective protection for underground utilities. They are manufactured from recycled polyethylene to be lightweight yet strong. Stokbord covers securely interconnect for continuous coverage, while Tapetile tape is flexible for easy installation. Both products have approvals from utility companies worldwide and offer visual warnings to prevent accidental damage during excavation work.
Street Lighting Polypipe Cable Duct
Ridgiduct and Polyduct lighting are twin wall and single wall cable protection systems for street lighting and traffic signals. They are manufactured in orange polyethylene (PE) or high-density polyethylene (HDPE) and include bends, reducers, and junction boxes to complete the system. Ridgicoil lighting provides a smooth bore PE cable protection in 50m coils for ease of cable installation. Access boxes and pole boxes provide protection and access for cable joints and are made from robust PE. Covers for the boxes can be composite, galvanized steel, or ductile iron depending on the expected loads.
Quicki straight & branch gel joint
The document discusses Gel Joints which are suitable for joining various cable types and provide excellent sealing and insulation. The Filoform Quicki range of Gel Joints has been designed to protect against moisture for small conductor applications. They are mainly used for unarmoured cables but can be used on some armoured cables with an armour continuity kit. The joints contain a gel-filled shell, connector block, cable ties and mounting instructions.
Polypipe Cable Ducting - Gas Pipe Ducting
Polypipe Cable Ducting - Gas Pipe Ducting
Single wall corrugated ducting for gas pipes. Available in either perforated or unperforated options.
Please ensure you are using this product to the correct specification of the end users requirements.
Zero Halogen Heat Shrink 120mm-40mm - W3 NH 120/40
This document provides information about medium and thick wall zero halogen adhesive lined heat shrink tube. It lists the product specifications, including sizes available from 3mm to 120mm diameter, shrink ratios of 3:1, and lengths up to 1.2 meters. The heat shrink tube is made of flexible, dual-wall, flame-retardant, non-halogen polyolefin material that reduces smoke and toxic gas emissions, making it suitable for applications in transportation and industrial areas. Part numbers, dimensions after recovery, and standard lengths are provided for the different tube sizes.
Pfisterer Sicon High Voltage Mechanical Shearbolt Connectors
The document describes a new type of cable connector called SICON that uses a stepless shear bolt. Key points:
1) SICON uses a stepless shear bolt that does not have predetermined breaking points, allowing it to achieve optimum clamping force for any conductor size.
2) Previous multi-stage shear bolts had breaking points that created discontinuities and did not allow maximum force. SICON's bolt breaks smoothly.
3) SICON provides up to 30% increased contact force on aluminum conductors compared to conventional connectors and ensures full utilization of the bolt's clamping ability.
LUL Compliant Optical Fibre 48 Way IP67 Splice Enclosures
This weatherproof enclosure provides secure splicing for up to 192 optical fibers. Made from durable 2mm stainless steel, it has IP67 waterproofing and is suited for harsh external applications. Individual trays each hold up to 12 fibers and the pivoting design allows for easy cable management and maintenance. Multiple cable entry points below allow uncomplicated routing of incoming cables.
Platinum Tools 15001C Data Sheet
This document summarizes a V-notch wire stripper that adjusts to different wire gauges. It has a precision-ground V-notch blade for stripping various wire insulations and a rotating cam wheel to adjust to the proper wire gauge. The stripper is made of high carbon steel, has a spring-loaded locking latch, and comes with a vinyl-dipped handle for comfort.
LappTannehill-Automotive-forWeb
Lapp Tannehill carries a full line of standard wire and cable products for automotive applications. This includes primary wire, ABS cable, battery cable, and welding cable. They offer products with features like thin-wall construction, heat resistance, flexibility, abrasion resistance, and more. Lapp Tannehill can meet various industry specifications and provides products for automotive wiring harnesses and other applications. They also offer related products like glands, conduit, connectors, and wire management accessories from a variety of qualified suppliers.
Anderton Ander-Fin Cable Theft Deterrent - Brochure
Ander-fin is a device that helps prevent cable theft, which costs the rail industry tens of millions each year and causes delays and safety hazards. Ander-fin secures cables every meter by enabling them to be tied down, and can secure long lengths of cable when used in conjunction with Anderton cable troughs.
Ds wbf6 24-series
The document summarizes a wall-mounted fiber optic enclosure called the WBF6-24. It can hold up to 24 fiber connections, has separate splice and patch areas, and four cable entries. It provides flexibility for installers by supporting different connector styles and allowing reconfiguration without disturbing installed fibers. Accessories include pigtails, bulkhead adapters, splice sleeves, and patch cords.
SPS Heat Shrink Joints to Suit Low Voltage Cables 0.6/3.3kV
This document provides information on heat shrink joints for low voltage cables produced by Shrink Polymer Systems. It lists various joint types for XLPE, PILC, and transition joints between XLPE and PILC cables with voltage ratings from 600/1000V to 3.3kV. The joints are intended for underground use and provide benefits such as unlimited shelf life, compact size to allow for immediate backfill, and fire resistance. Thousands of these joints have been installed in various infrastructure projects worldwide. Part numbers are specified according to cable size and construction.
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kV
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kVThorne & Derrick International
This document provides information on heat shrink joints for low voltage cables. It describes the components of the joints, which include adhesive lined tubes, armour cages, rings and clamps, and heat shrink tubes. The joints are intended for voltages up to 3.3kV and cable sizes ranging from 1.5mm2 to 630mm2. Part numbers are provided for single core and multicore joints for XLPE, PILC and transition cables. The joints are designed to meet industry standards and have an unlimited shelf life.Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...
Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...Thorne & Derrick International
This document provides information on heat shrink terminations for low voltage PILC cables ranging from 0.6/1kV. It lists the part numbers, cable ranges, and tail lengths for single core and 3 core indoor/outdoor heat shrink terminations for XLPE and PILC cables ranging from 1.9/3.6kV. It also lists part numbers for 3/4 core PILC cable terminations ranging from 4-300mm2 with tail lengths of 600mm or 1000mm. An note indicates that for 4 core terminations, the last digit of the part number should read -4.Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)
Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)Thorne & Derrick International
The document describes Prysmian's Multicleat/Multistrap cable fixing system. It provides details on the components of the system including Multicleats, Multistraps, and LSF Liners. Multicleats are cable cleats with bases that can anchor cables individually or in trefoil formation. Multistraps are used as intermediate restraints between Multicleats and can bind cables together. The document lists specifications for different Multicleat and Multistrap sizes based on cable diameter ranges and provides installation guidelines.Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...
Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...Thorne & Derrick International
Prysmian Group is a worldwide leader in cable systems and accessories. They provide major organizations with cable solutions tailored to their needs. This document discusses Prysmian Group's cable support and fixing systems product range, including cleats for single cables and trefoil configurations. It provides information on selecting the appropriate cleat based on cable size and application requirements.3M 8425-8 Cold Shrink Tube
3M Cold Shrink Tube 8425-83M 8425-8 Cold Shrink Tube
Cold Shrink Tube Min Diameter 10.2mm
Cold Shrink Tube Max Diameter 20.8mm
Cold Shrink Tube Length 203mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8423-6 Cold Shrink Tube
3M Brand PST Cold Shrink Connector Insulators are open-ended, tubular rubber sleeves that are factory expanded and assembled onto a removable core. They are used to provide primary electrical insulation and physical protection for cable splices and connections rated up to 1000 volts. The insulators are made of EPDM rubber and are installed by removing the core, allowing the tube to shrink and form a waterproof seal around the cable or connection. They can be used for indoor, outdoor, overhead, buried, or submerged applications without additional heat or adhesives.
3M 8428-18 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8428-183M 8428-18 Cold Shrink Tube
Cold Shrink Tube Min Diameter 24.0mm
Cold Shrink Tube Max Diameter 49.3mm
Cold Shrink Tube Length 457mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8429-12 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8429-123M 8429-12 Cold Shrink Tube
Cold Shrink Tube Min Diameter 32.2mm
Cold Shrink Tube Max Diameter 67.8mm
Cold Shrink Tube Length 305mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors
More Related Content
What's hot
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...Thorne & Derrick International
This document provides information on heat shrink joints for low voltage cables produced by Shrink Polymer Systems. It lists various joint part numbers for joining single core and multicore XLPE, PVC, PILC and transition cables with voltage ratings from 600/1000V to 3.3kV. The joints are intended for underground use and comprise adhesive lined tubes, armour supports, clamps and heat shrink outer tubes to meet BS6910-1 standards with unlimited shelf life. Thousands of these joints have been installed in critical infrastructure projects worldwide.Charles Endirect Street Lighting Equipment
Charles Endirect Ltd (CEL) is a leading UK manufacturer of street lighting equipment located in Somerset. CEL produces isolators, cut outs, feeder pillars, distribution boards, and pre-wired pillars. The company was formed in 1985 through the merger of two family businesses and has grown to serve local authorities, highways agencies, and rail networks across the UK, Ireland, and internationally. CEL is committed to innovation, high quality, and excellent customer service.
Centriforce Utility Protection Brochure
Stokbord and Tapetile cable protection systems provide durable, impact-resistant, and cost-effective protection for underground utilities. They are manufactured from recycled polyethylene to be lightweight yet strong. Stokbord covers securely interconnect for continuous coverage, while Tapetile tape is flexible for easy installation. Both products have approvals from utility companies worldwide and offer visual warnings to prevent accidental damage during excavation work.
Street Lighting Polypipe Cable Duct
Ridgiduct and Polyduct lighting are twin wall and single wall cable protection systems for street lighting and traffic signals. They are manufactured in orange polyethylene (PE) or high-density polyethylene (HDPE) and include bends, reducers, and junction boxes to complete the system. Ridgicoil lighting provides a smooth bore PE cable protection in 50m coils for ease of cable installation. Access boxes and pole boxes provide protection and access for cable joints and are made from robust PE. Covers for the boxes can be composite, galvanized steel, or ductile iron depending on the expected loads.
Quicki straight & branch gel joint
The document discusses Gel Joints which are suitable for joining various cable types and provide excellent sealing and insulation. The Filoform Quicki range of Gel Joints has been designed to protect against moisture for small conductor applications. They are mainly used for unarmoured cables but can be used on some armoured cables with an armour continuity kit. The joints contain a gel-filled shell, connector block, cable ties and mounting instructions.
Polypipe Cable Ducting - Gas Pipe Ducting
Polypipe Cable Ducting - Gas Pipe Ducting
Single wall corrugated ducting for gas pipes. Available in either perforated or unperforated options.
Please ensure you are using this product to the correct specification of the end users requirements.
Zero Halogen Heat Shrink 120mm-40mm - W3 NH 120/40
This document provides information about medium and thick wall zero halogen adhesive lined heat shrink tube. It lists the product specifications, including sizes available from 3mm to 120mm diameter, shrink ratios of 3:1, and lengths up to 1.2 meters. The heat shrink tube is made of flexible, dual-wall, flame-retardant, non-halogen polyolefin material that reduces smoke and toxic gas emissions, making it suitable for applications in transportation and industrial areas. Part numbers, dimensions after recovery, and standard lengths are provided for the different tube sizes.
Pfisterer Sicon High Voltage Mechanical Shearbolt Connectors
The document describes a new type of cable connector called SICON that uses a stepless shear bolt. Key points:
1) SICON uses a stepless shear bolt that does not have predetermined breaking points, allowing it to achieve optimum clamping force for any conductor size.
2) Previous multi-stage shear bolts had breaking points that created discontinuities and did not allow maximum force. SICON's bolt breaks smoothly.
3) SICON provides up to 30% increased contact force on aluminum conductors compared to conventional connectors and ensures full utilization of the bolt's clamping ability.
LUL Compliant Optical Fibre 48 Way IP67 Splice Enclosures
This weatherproof enclosure provides secure splicing for up to 192 optical fibers. Made from durable 2mm stainless steel, it has IP67 waterproofing and is suited for harsh external applications. Individual trays each hold up to 12 fibers and the pivoting design allows for easy cable management and maintenance. Multiple cable entry points below allow uncomplicated routing of incoming cables.
Platinum Tools 15001C Data Sheet
This document summarizes a V-notch wire stripper that adjusts to different wire gauges. It has a precision-ground V-notch blade for stripping various wire insulations and a rotating cam wheel to adjust to the proper wire gauge. The stripper is made of high carbon steel, has a spring-loaded locking latch, and comes with a vinyl-dipped handle for comfort.
LappTannehill-Automotive-forWeb
Lapp Tannehill carries a full line of standard wire and cable products for automotive applications. This includes primary wire, ABS cable, battery cable, and welding cable. They offer products with features like thin-wall construction, heat resistance, flexibility, abrasion resistance, and more. Lapp Tannehill can meet various industry specifications and provides products for automotive wiring harnesses and other applications. They also offer related products like glands, conduit, connectors, and wire management accessories from a variety of qualified suppliers.
Anderton Ander-Fin Cable Theft Deterrent - Brochure
Ander-fin is a device that helps prevent cable theft, which costs the rail industry tens of millions each year and causes delays and safety hazards. Ander-fin secures cables every meter by enabling them to be tied down, and can secure long lengths of cable when used in conjunction with Anderton cable troughs.
Ds wbf6 24-series
The document summarizes a wall-mounted fiber optic enclosure called the WBF6-24. It can hold up to 24 fiber connections, has separate splice and patch areas, and four cable entries. It provides flexibility for installers by supporting different connector styles and allowing reconfiguration without disturbing installed fibers. Accessories include pigtails, bulkhead adapters, splice sleeves, and patch cords.
What's hot (13)
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...
Heat Shrink Joints to Suit Single Core Low Voltage Cables Type XLPE/SWA/PVC 0...
Zero Halogen Heat Shrink 120mm-40mm - W3 NH 120/40
Zero Halogen Heat Shrink 120mm-40mm - W3 NH 120/40
Pfisterer Sicon High Voltage Mechanical Shearbolt Connectors
Pfisterer Sicon High Voltage Mechanical Shearbolt Connectors
LUL Compliant Optical Fibre 48 Way IP67 Splice Enclosures
LUL Compliant Optical Fibre 48 Way IP67 Splice Enclosures
Anderton Ander-Fin Cable Theft Deterrent - Brochure
Anderton Ander-Fin Cable Theft Deterrent - Brochure
Similar to SPS HCS2 Heat Shrink Cable Glands 7-17mm
SPS Heat Shrink Joints to Suit Low Voltage Cables 0.6/3.3kV
This document provides information on heat shrink joints for low voltage cables produced by Shrink Polymer Systems. It lists various joint types for XLPE, PILC, and transition joints between XLPE and PILC cables with voltage ratings from 600/1000V to 3.3kV. The joints are intended for underground use and provide benefits such as unlimited shelf life, compact size to allow for immediate backfill, and fire resistance. Thousands of these joints have been installed in various infrastructure projects worldwide. Part numbers are specified according to cable size and construction.
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kV
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kVThorne & Derrick International
This document provides information on heat shrink joints for low voltage cables. It describes the components of the joints, which include adhesive lined tubes, armour cages, rings and clamps, and heat shrink tubes. The joints are intended for voltages up to 3.3kV and cable sizes ranging from 1.5mm2 to 630mm2. Part numbers are provided for single core and multicore joints for XLPE, PILC and transition cables. The joints are designed to meet industry standards and have an unlimited shelf life.Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...
Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...Thorne & Derrick International
This document provides information on heat shrink terminations for low voltage PILC cables ranging from 0.6/1kV. It lists the part numbers, cable ranges, and tail lengths for single core and 3 core indoor/outdoor heat shrink terminations for XLPE and PILC cables ranging from 1.9/3.6kV. It also lists part numbers for 3/4 core PILC cable terminations ranging from 4-300mm2 with tail lengths of 600mm or 1000mm. An note indicates that for 4 core terminations, the last digit of the part number should read -4.Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)
Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)Thorne & Derrick International
The document describes Prysmian's Multicleat/Multistrap cable fixing system. It provides details on the components of the system including Multicleats, Multistraps, and LSF Liners. Multicleats are cable cleats with bases that can anchor cables individually or in trefoil formation. Multistraps are used as intermediate restraints between Multicleats and can bind cables together. The document lists specifications for different Multicleat and Multistrap sizes based on cable diameter ranges and provides installation guidelines.Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...
Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...Thorne & Derrick International
Prysmian Group is a worldwide leader in cable systems and accessories. They provide major organizations with cable solutions tailored to their needs. This document discusses Prysmian Group's cable support and fixing systems product range, including cleats for single cables and trefoil configurations. It provides information on selecting the appropriate cleat based on cable size and application requirements.3M 8425-8 Cold Shrink Tube
3M Cold Shrink Tube 8425-83M 8425-8 Cold Shrink Tube
Cold Shrink Tube Min Diameter 10.2mm
Cold Shrink Tube Max Diameter 20.8mm
Cold Shrink Tube Length 203mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8423-6 Cold Shrink Tube
3M Brand PST Cold Shrink Connector Insulators are open-ended, tubular rubber sleeves that are factory expanded and assembled onto a removable core. They are used to provide primary electrical insulation and physical protection for cable splices and connections rated up to 1000 volts. The insulators are made of EPDM rubber and are installed by removing the core, allowing the tube to shrink and form a waterproof seal around the cable or connection. They can be used for indoor, outdoor, overhead, buried, or submerged applications without additional heat or adhesives.
3M 8428-18 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8428-183M 8428-18 Cold Shrink Tube
Cold Shrink Tube Min Diameter 24.0mm
Cold Shrink Tube Max Diameter 49.3mm
Cold Shrink Tube Length 457mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8429-12 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8429-123M 8429-12 Cold Shrink Tube
Cold Shrink Tube Min Diameter 32.2mm
Cold Shrink Tube Max Diameter 67.8mm
Cold Shrink Tube Length 305mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors
3M 8429-6 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8429-63M 8429-6 Cold Shrink Tube
Cold Shrink Tube Min Diameter 32.2mm
Cold Shrink Tube Max Diameter 67.8mm
Cold Shrink Tube Length 152mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8426-11 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables 3M Cold Shrink Tube 8426-11 Cold Shrink Tube Min Diameter 13.0mm Cold Shrink Tube Max Diameter 25.4mm Cold Shrink Tube Length 279mm 3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core. •Cold shrink provides a constant radial pressure seal •No heat required with 3M Cold Shrink - 100% cold applied •No specialist cable jointing or heat shrink tools required •Quality - long term reliability •Moisture resistant for submersible and outdoor applications 3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8427-12 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8427-123M 8427-12 Cold Shrink Tube
Cold Shrink Tube Min Diameter 17.5mm
Cold Shrink Tube Max Diameter 33.0mm
Cold Shrink Tube Length 305mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8429-18 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8429-123M 8429-18 Cold Shrink Tube
Cold Shrink Tube Min Diameter 32.2mm
Cold Shrink Tube Max Diameter 67.8mm
Cold Shrink Tube Length 457mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8430-18 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables 3M Cold Shrink Tube 8430-9 Cold Shrink Tube Min Diameter 42.6mm Cold Shrink Tube Max Diameter 93.7mm Cold Shrink Tube Length 229mm 3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core. •Cold shrink provides a constant radial pressure seal •No heat required with 3M Cold Shrink - 100% cold applied •No specialist cable jointing or heat shrink tools required •Quality - long term reliability •Moisture resistant for submersible and outdoor applications 3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8427-16 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8427-163M 8427-16 Cold Shrink Tube
Cold Shrink Tube Min Diameter 17.5mm
Cold Shrink Tube Max Diameter 33.0mm
Cold Shrink Tube Length 406mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8428-24 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8428-243M 8428-24 Cold Shrink Tube
Cold Shrink Tube Min Diameter 24.0mm
Cold Shrink Tube Max Diameter 49.3mm
Cold Shrink Tube Length 609mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8426-9 Cold Shrink Tube
3M Cold Shrink EPDM Tubes (8420 series) are open-ended rubber sleeves that are factory expanded and placed over a removable core. They are used to provide insulation and waterproof sealing for cable connections and terminations rated up to 1000 volts. The tubes are made of EPDM rubber and shrink to form a tight seal when the core is removed after positioning over the connection. They can be used for indoor, outdoor, overhead, buried, or submerged applications without additional heat or adhesives.
3M 8429-9 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8429-93M 8429-9 Cold Shrink Tube
Cold Shrink Tube Min Diameter 32.2mm
Cold Shrink Tube Max Diameter 67.8mm
Cold Shrink Tube Length 229mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8428-12 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8428-123M 8428-12 Cold Shrink Tube
Cold Shrink Tube Min Diameter 24.0mm
Cold Shrink Tube Max Diameter 49.3mm
Cold Shrink Tube Length 305mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
3M 8428-6 Cold Shrink Tube
3M Cold Shrink Tubes Seal, Splice & Protect LV Power Cables
3M Cold Shrink Tube 8428-63M 8428-6 Cold Shrink Tube
Cold Shrink Tube Min Diameter 24.0mm
Cold Shrink Tube Max Diameter 49.3mm
Cold Shrink Tube Length 152mm
3M Cold Shrink Tube is a pre-stretched EPDM rubber tubing, factory expanded and assembled onto a removable core.
•Cold shrink provides a constant radial pressure seal
•No heat required with 3M Cold Shrink - 100% cold applied
•No specialist cable jointing or heat shrink tools required
•Quality - long term reliability
•Moisture resistant for submersible and outdoor applications
3M Cold Shrink Tubes are suitable for cable protection and moisture ingress protection - 3M Cold Shrink EPDM tubings are suitable as primary insulation on low voltage cables and cable splices up to 1000v AC. Cold shrink tubes provide electrical protection and moisture sealing for high-voltage, air-insulated connectors and cable lugs such as spacer cable and cable lug connections to bus bar. 3M cold shrink tubes also provide electrical insulation of secondary splices including copper or aluminium connectors.
Similar to SPS HCS2 Heat Shrink Cable Glands 7-17mm (20)
SPS Heat Shrink Joints to Suit Low Voltage Cables 0.6/3.3kV
SPS Heat Shrink Joints to Suit Low Voltage Cables 0.6/3.3kV
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kV
Heat Shrink Joints to Suit Low Voltage Cables Type XLPE/SWA/PVC 0.6/3.3kV
Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...
Heat Shrink Cable Terminations to suit XLPE & Paper Insulated Lead Covered Ca...
Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)
Prysmian Cable Cleats - Bicon Multicleats & Bicon Multistraps (Stainless Steel)
Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...
Prysmian Cable Support & Fixing System Catalogue - Prysmian Group (Bicon) Cab...
More from Thorne & Derrick International
Isolation procedures for safe working on electrical systems and equipment by ...
Isolation procedures for safe working on electrical systems and equipment by ...Thorne & Derrick International
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical Eqpt
THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical EqptThorne & Derrick International
Thorne & Derrick International are specialist distributors of low, medium, and high voltage cable installation, jointing, substation, and electrical equipment. They have over 30 years of experience and stock over 100,000 products from over 100 brands. Their product range includes cable joints, terminations, tools, accessories, distribution equipment, and safety products for voltages up to 132kV.The Children North East Annual Golf Day Wednesday 9th May 2018
The document advertises the Children North East Annual Golf Day fundraising event to be held on May 9th, 2018 at Close House golf course in Northumberland. The event will include a shotgun start at 2pm for teams of four playing in a Stableford scoring competition. The £490 entry fee per team includes breakfast, a two course meal after play, and goodie bags. Proceeds will benefit Children North East, a charity supporting children in the Newcastle region.
3M Electrical Products Stocked By Thorne & Derrick International
This document provides information on 3M's electrical products, including electrical connectors, wire connectors, splice kits, wire markers, and protective coatings. It highlights key features and applications of 3M's Scotchlok electrical insulation displacement connectors, Performance Plus wire connectors, direct bury splice kits, ScotchCode wire markers, insulating and anti-corrosion sprays, and Scotchkote electrical coating. The document is intended to showcase 3M's quality solutions for electrical connections, identification, and corrosion protection.
CATU Electrical Safety Catalogue
This document provides a catalogue of products from SICAME GROUP for electrical safety. It begins by emphasizing the importance of electrical safety for professionals working in the electrical industry. The catalogue then outlines the company's commitment to supporting customers through new products designed by their teams, an updated catalogue focusing on product functions and uses, and new educational tools like guidance documents. The bulk of the document consists of the catalogue content organized into sections covering personal protective equipment, locking, signaling, low voltage test and measurement, low voltage earthing systems, low voltage live working tools, medium voltage substation equipment, medium voltage equipment, high voltage lines and switchgear equipment, and earthing connections. Each section lists and provides brief descriptions of the various safety products
11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-A
11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-AThorne & Derrick International
1) The document provides installation instructions for heatshrink termination of 3 core polymeric cables with voltages ranging from 7.2kV to 36kV. It describes the steps for preparing the cable, installing stress control tapes and tubes, cable lugs, and rain sheds.
2) Key steps include removing the cable sheath and screens, applying stress control tape, installing cable lugs and boots, and shrinking tubes onto the assembly. Proper distances must be maintained for phase clearance and bending radii.
3) Outdoor terminations require additional rain sheds installed from the bottom up at specified distances between the anti-track tube and shed edges. Indoor distances between phases and grounds are also outlined.THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...
THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...Thorne & Derrick International
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...
Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...Thorne & Derrick International
The document provides technical specifications for EJB series explosion proof enclosures made of galvanized carbon steel. The enclosures have an IP rating of IP65, IP66, or IP67 and an operating temperature range of -50°C to +60°C. They offer explosion protection of Ex d IIB or IIB+H2 and are suitable for indoor and outdoor use in hazardous industrial areas. The enclosures can house various electrical and electronic components and accessories.Roxtec Cable Transit - B Frame Dimensional Drawing
Roxtec Cable Transit - B Frame Dimensional Drawing
Pepperl & Fuchs SIL Training Certificate - T&D Adam Rowe
This certificate of attendance awards Adam Rowe and Michael Wenglorz for successfully completing a SIL (Safety Integrity Level) training seminar held by PEPPERL+FUCHS GB LTD on November 7th, 2016.
T&D Experts In Equipment For Explosive Atmospheres
Thorne & Derrick were established in 1985 and are now one of the largest specialist distributors and worldwide exporters of equipment for explosive atmospheres. They stock over 100,000 products from over 100 brands for industries such as oil & gas, mining, manufacturing, and more. Thorne & Derrick provide hazardous area lighting, heating, sensors, detectors, valves, cables, and other equipment certified for explosive atmospheres. They also offer technical support, international delivery, and over 30 years of experience in serving hazardous area applications.
Ultrasonic Flow Meters - Customer Specification Demand
This document is an application datasheet for flow measurement devices. It requests contact and process information from customers. It asks for details about the application environment and pipe parameters. It also requests information on process parameters like temperature, pressure, and flow rates. Finally, it inquires about desired measurement configuration including units of measurement, data logging, power supply, and electrical and communication interfaces.
Emtelle Fibre Optic Cables - Product Catalogue 2016
This document provides information on Emtelle fibre optic cables, including:
- An overview of Emtelle as a leading global manufacturer of blown fibre and ducted network solutions.
- Descriptions of different cable types including Direct Install, Direct Buried, Aerial, and more.
- Specifications for various cable models including fibre count options, dimensions, tensile strength and other test standards.
Thorne & Derrick Process Heating Brochure 2016
Thorne & Derrick provide electrical heating solutions for industrial and hazardous area applications. They have over 30 years of experience in process heating and specialize in frost protection and winterization packages. They offer a wide range of electrical heating equipment for hazardous areas, including portable air heaters certified for use in explosive atmospheres. Their product range and engineering expertise help customers solve heating challenges across various industries.
SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D
SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D
Ripley Utility Tool Cable Preparation Tools
The document provides information on tools for preparing electric utility distribution and transmission cables. It includes tools for stripping insulation from secondary distribution cables, mid-span stripping of overhead primary distribution cables, insulation stripping and jacket stripping for underground cables, removing insulation shields from underground and transmission cables, pencilling transmission cables, and other specialty distribution tools. Tables provide part numbers and specifications for various cable end strippers and other tools to prepare different cable types.
RIDGID micro CD100 Combustible Gas Detector
The document describes the RIDGID micro CD-100 combustible gas leak detector. It can quickly identify the presence of combustible gases with a flexible 41 cm probe. It is designed to detect gases like methane, propane, and more. The micro CD-100 has adjustable sensitivity settings and Tri-Mode Detection that provides alerts through visual, audible or vibration signals. It is listed as catalog number 36163 and weighs 0.45 kg.
Itron Fact Sheet
Itron is a leading technology company dedicated to measuring, managing, and analyzing energy and water resources. It provides comprehensive solutions including meters, communication systems, software, and consulting services to over 8,000 customers in more than 100 countries. Itron employs thousands of people globally and invests over 8.5% of its $1.9 billion annual revenue in research and development.
United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...
United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...Thorne & Derrick International
United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration, Air Conditioning & Heat Pumps Technical Options Committee’Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet
Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec SheetThorne & Derrick International
The FiloSeal+HD is a duct sealing system that uses hexagonal tubes and a flexible silicon-based sealant to seal cable configurations and pipes within conduits. It provides resistance to up to 2 bars of pressure and can withstand pulling forces of 100kg on sealed cables. The sealant is easily applied and cures with air, providing high levels of gas and water tightness. The system allows for easy addition or removal of cables or pipes as needed.More from Thorne & Derrick International (20)
Isolation procedures for safe working on electrical systems and equipment by ...
Isolation procedures for safe working on electrical systems and equipment by ...
THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical Eqpt
THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical Eqpt
The Children North East Annual Golf Day Wednesday 9th May 2018
The Children North East Annual Golf Day Wednesday 9th May 2018
3M Electrical Products Stocked By Thorne & Derrick International
3M Electrical Products Stocked By Thorne & Derrick International
11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-A
11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-A
THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...
THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...
Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...
Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...
Roxtec Cable Transit - B Frame Dimensional Drawing
Roxtec Cable Transit - B Frame Dimensional Drawing
Pepperl & Fuchs SIL Training Certificate - T&D Adam Rowe
Pepperl & Fuchs SIL Training Certificate - T&D Adam Rowe
T&D Experts In Equipment For Explosive Atmospheres
T&D Experts In Equipment For Explosive Atmospheres
Ultrasonic Flow Meters - Customer Specification Demand
Ultrasonic Flow Meters - Customer Specification Demand
Emtelle Fibre Optic Cables - Product Catalogue 2016
Emtelle Fibre Optic Cables - Product Catalogue 2016
SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D
SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D
United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...
United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...
Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet
Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet
Recently uploaded
GlobalLogic Java Community Webinar #18 “How to Improve Web Application Perfor...
Під час доповіді відповімо на питання, навіщо потрібно підвищувати продуктивність аплікації і які є найефективніші способи для цього. А також поговоримо про те, що таке кеш, які його види бувають та, основне — як знайти performance bottleneck?
Відео та деталі заходу: https://bit.ly/45tILxj
Demystifying Knowledge Management through Storytelling
The Department of Veteran Affairs (VA) invited Taylor Paschal, Knowledge & Information Management Consultant at Enterprise Knowledge, to speak at a Knowledge Management Lunch and Learn hosted on June 12, 2024. All Office of Administration staff were invited to attend and received professional development credit for participating in the voluntary event.
The objectives of the Lunch and Learn presentation were to:
- Review what KM ‘is’ and ‘isn’t’
- Understand the value of KM and the benefits of engaging
- Define and reflect on your “what’s in it for me?”
- Share actionable ways you can participate in Knowledge - - Capture & Transfer
AWS Certified Solutions Architect Associate (SAA-C03)
AWS Certified Solutions Architect Associate (SAA-C03)
"$10 thousand per minute of downtime: architecture, queues, streaming and fin...
Direct losses from downtime in 1 minute = $5-$10 thousand dollars. Reputation is priceless.
As part of the talk, we will consider the architectural strategies necessary for the development of highly loaded fintech solutions. We will focus on using queues and streaming to efficiently work and manage large amounts of data in real-time and to minimize latency.
We will focus special attention on the architectural patterns used in the design of the fintech system, microservices and event-driven architecture, which ensure scalability, fault tolerance, and consistency of the entire system.
QR Secure: A Hybrid Approach Using Machine Learning and Security Validation F...
QR Secure: A Hybrid Approach Using Machine Learning and Security Validation Functions to Prevent Interaction with Malicious QR Codes.
Aim of the Study: The goal of this research was to develop a robust hybrid approach for identifying malicious and insecure URLs derived from QR codes, ensuring safe interactions.
This is achieved through:
Machine Learning Model: Predicts the likelihood of a URL being malicious.
Security Validation Functions: Ensures the derived URL has a valid certificate and proper URL format.
This innovative blend of technology aims to enhance cybersecurity measures and protect users from potential threats hidden within QR codes 🖥 🔒
This study was my first introduction to using ML which has shown me the immense potential of ML in creating more secure digital environments!
Leveraging the Graph for Clinical Trials and Standards
Katja Glaß
OpenStudyBuilder Community Manager - Katja Glaß Consulting
Marius Conjeaud
Principal Consultant - Neo4j
Harnessing the Power of NLP and Knowledge Graphs for Opioid Research
Gursev Pirge, PhD
Senior Data Scientist - JohnSnowLabs
Northern Engraving | Modern Metal Trim, Nameplates and Appliance Panels
What began over 115 years ago as a supplier of precision gauges to the automotive industry has evolved into being an industry leader in the manufacture of product branding, automotive cockpit trim and decorative appliance trim. Value-added services include in-house Design, Engineering, Program Management, Test Lab and Tool Shops.
"NATO Hackathon Winner: AI-Powered Drug Search", Taras Kloba
This is a session that details how PostgreSQL's features and Azure AI Services can be effectively used to significantly enhance the search functionality in any application.
In this session, we'll share insights on how we used PostgreSQL to facilitate precise searches across multiple fields in our mobile application. The techniques include using LIKE and ILIKE operators and integrating a trigram-based search to handle potential misspellings, thereby increasing the search accuracy.
We'll also discuss how the azure_ai extension on PostgreSQL databases in Azure and Azure AI Services were utilized to create vectors from user input, a feature beneficial when users wish to find specific items based on text prompts. While our application's case study involves a drug search, the techniques and principles shared in this session can be adapted to improve search functionality in a wide range of applications. Join us to learn how PostgreSQL and Azure AI can be harnessed to enhance your application's search capability.
Getting the Most Out of ScyllaDB Monitoring: ShareChat's Tips
ScyllaDB monitoring provides a lot of useful information. But sometimes it’s not easy to find the root of the problem if something is wrong or even estimate the remaining capacity by the load on the cluster. This talk shares our team's practical tips on: 1) How to find the root of the problem by metrics if ScyllaDB is slow 2) How to interpret the load and plan capacity for the future 3) Compaction strategies and how to choose the right one 4) Important metrics which aren’t available in the default monitoring setup.
inQuba Webinar Mastering Customer Journey Management with Dr Graham Hill
HERE IS YOUR WEBINAR CONTENT! 'Mastering Customer Journey Management with Dr. Graham Hill'. We hope you find the webinar recording both insightful and enjoyable.
In this webinar, we explored essential aspects of Customer Journey Management and personalization. Here’s a summary of the key insights and topics discussed:
Key Takeaways:
Understanding the Customer Journey: Dr. Hill emphasized the importance of mapping and understanding the complete customer journey to identify touchpoints and opportunities for improvement.
Personalization Strategies: We discussed how to leverage data and insights to create personalized experiences that resonate with customers.
Technology Integration: Insights were shared on how inQuba’s advanced technology can streamline customer interactions and drive operational efficiency.
Apps Break Data
How information systems are built or acquired puts information, which is what they should be about, in a secondary place. Our language adapted accordingly, and we no longer talk about information systems but applications. Applications evolved in a way to break data into diverse fragments, tightly coupled with applications and expensive to integrate. The result is technical debt, which is re-paid by taking even bigger "loans", resulting in an ever-increasing technical debt. Software engineering and procurement practices work in sync with market forces to maintain this trend. This talk demonstrates how natural this situation is. The question is: can something be done to reverse the trend?
LF Energy Webinar: Carbon Data Specifications: Mechanisms to Improve Data Acc...
This LF Energy webinar took place June 20, 2024. It featured:
-Alex Thornton, LF Energy
-Hallie Cramer, Google
-Daniel Roesler, UtilityAPI
-Henry Richardson, WattTime
In response to the urgency and scale required to effectively address climate change, open source solutions offer significant potential for driving innovation and progress. Currently, there is a growing demand for standardization and interoperability in energy data and modeling. Open source standards and specifications within the energy sector can also alleviate challenges associated with data fragmentation, transparency, and accessibility. At the same time, it is crucial to consider privacy and security concerns throughout the development of open source platforms.
This webinar will delve into the motivations behind establishing LF Energy’s Carbon Data Specification Consortium. It will provide an overview of the draft specifications and the ongoing progress made by the respective working groups.
Three primary specifications will be discussed:
-Discovery and client registration, emphasizing transparent processes and secure and private access
-Customer data, centering around customer tariffs, bills, energy usage, and full consumption disclosure
-Power systems data, focusing on grid data, inclusive of transmission and distribution networks, generation, intergrid power flows, and market settlement data
Day 2 - Intro to UiPath Studio Fundamentals
In our second session, we shall learn all about the main features and fundamentals of UiPath Studio that enable us to use the building blocks for any automation project.
📕 Detailed agenda:
Variables and Datatypes
Workflow Layouts
Arguments
Control Flows and Loops
Conditional Statements
💻 Extra training through UiPath Academy:
Variables, Constants, and Arguments in Studio
Control Flow in Studio
"Frontline Battles with DDoS: Best practices and Lessons Learned", Igor Ivaniuk
At this talk we will discuss DDoS protection tools and best practices, discuss network architectures and what AWS has to offer. Also, we will look into one of the largest DDoS attacks on Ukrainian infrastructure that happened in February 2022. We'll see, what techniques helped to keep the web resources available for Ukrainians and how AWS improved DDoS protection for all customers based on Ukraine experience
Lee Barnes - Path to Becoming an Effective Test Automation Engineer.pdf
So… you want to become a Test Automation Engineer (or hire and develop one)? While there’s quite a bit of information available about important technical and tool skills to master, there’s not enough discussion around the path to becoming an effective Test Automation Engineer that knows how to add VALUE. In my experience this had led to a proliferation of engineers who are proficient with tools and building frameworks but have skill and knowledge gaps, especially in software testing, that reduce the value they deliver with test automation.
In this talk, Lee will share his lessons learned from over 30 years of working with, and mentoring, hundreds of Test Automation Engineers. Whether you’re looking to get started in test automation or just want to improve your trade, this talk will give you a solid foundation and roadmap for ensuring your test automation efforts continuously add value. This talk is equally valuable for both aspiring Test Automation Engineers and those managing them! All attendees will take away a set of key foundational knowledge and a high-level learning path for leveling up test automation skills and ensuring they add value to their organizations.
Connector Corner: Seamlessly power UiPath Apps, GenAI with prebuilt connectors
Join us to learn how UiPath Apps can directly and easily interact with prebuilt connectors via Integration Service--including Salesforce, ServiceNow, Open GenAI, and more.
The best part is you can achieve this without building a custom workflow! Say goodbye to the hassle of using separate automations to call APIs. By seamlessly integrating within App Studio, you can now easily streamline your workflow, while gaining direct access to our Connector Catalog of popular applications.
We’ll discuss and demo the benefits of UiPath Apps and connectors including:
Creating a compelling user experience for any software, without the limitations of APIs.
Accelerating the app creation process, saving time and effort
Enjoying high-performance CRUD (create, read, update, delete) operations, for
seamless data management.
Speakers:
Russell Alfeche, Technology Leader, RPA at qBotic and UiPath MVP
Charlie Greenberg, host
Essentials of Automations: Exploring Attributes & Automation Parameters
Building automations in FME Flow can save time, money, and help businesses scale by eliminating data silos and providing data to stakeholders in real-time. One essential component to orchestrating complex automations is the use of attributes & automation parameters (both formerly known as “keys”). In fact, it’s unlikely you’ll ever build an Automation without using these components, but what exactly are they?
Attributes & automation parameters enable the automation author to pass data values from one automation component to the next. During this webinar, our FME Flow Specialists will cover leveraging the three types of these output attributes & parameters in FME Flow: Event, Custom, and Automation. As a bonus, they’ll also be making use of the Split-Merge Block functionality.
You’ll leave this webinar with a better understanding of how to maximize the potential of automations by making use of attributes & automation parameters, with the ultimate goal of setting your enterprise integration workflows up on autopilot.
JavaLand 2024: Application Development Green Masterplan
My presentation slides I used at JavaLand 2024
Recently uploaded (20)
GlobalLogic Java Community Webinar #18 “How to Improve Web Application Perfor...
GlobalLogic Java Community Webinar #18 “How to Improve Web Application Perfor...
Demystifying Knowledge Management through Storytelling
Demystifying Knowledge Management through Storytelling
AWS Certified Solutions Architect Associate (SAA-C03)
AWS Certified Solutions Architect Associate (SAA-C03)
"$10 thousand per minute of downtime: architecture, queues, streaming and fin...
"$10 thousand per minute of downtime: architecture, queues, streaming and fin...
QR Secure: A Hybrid Approach Using Machine Learning and Security Validation F...
QR Secure: A Hybrid Approach Using Machine Learning and Security Validation F...
Leveraging the Graph for Clinical Trials and Standards
Leveraging the Graph for Clinical Trials and Standards
Harnessing the Power of NLP and Knowledge Graphs for Opioid Research
Harnessing the Power of NLP and Knowledge Graphs for Opioid Research
Northern Engraving | Modern Metal Trim, Nameplates and Appliance Panels
Northern Engraving | Modern Metal Trim, Nameplates and Appliance Panels
"NATO Hackathon Winner: AI-Powered Drug Search", Taras Kloba
"NATO Hackathon Winner: AI-Powered Drug Search", Taras Kloba
Getting the Most Out of ScyllaDB Monitoring: ShareChat's Tips
Getting the Most Out of ScyllaDB Monitoring: ShareChat's Tips
inQuba Webinar Mastering Customer Journey Management with Dr Graham Hill
inQuba Webinar Mastering Customer Journey Management with Dr Graham Hill
LF Energy Webinar: Carbon Data Specifications: Mechanisms to Improve Data Acc...
LF Energy Webinar: Carbon Data Specifications: Mechanisms to Improve Data Acc...
"Frontline Battles with DDoS: Best practices and Lessons Learned", Igor Ivaniuk
"Frontline Battles with DDoS: Best practices and Lessons Learned", Igor Ivaniuk
Lee Barnes - Path to Becoming an Effective Test Automation Engineer.pdf
Lee Barnes - Path to Becoming an Effective Test Automation Engineer.pdf
Connector Corner: Seamlessly power UiPath Apps, GenAI with prebuilt connectors
Connector Corner: Seamlessly power UiPath Apps, GenAI with prebuilt connectors
Essentials of Automations: Exploring Attributes & Automation Parameters
Essentials of Automations: Exploring Attributes & Automation Parameters
JavaLand 2024: Application Development Green Masterplan
JavaLand 2024: Application Development Green Masterplan
SPS HCS2 Heat Shrink Cable Glands 7-17mm
- 1. Unit E3, Crown Way, Crown Park Industrial Estate, Rushden, Northants, UK, NN10 6FD Tel: +44 (0)1933 356758 Fax: +44 (0)1933 413821 Email: info@shrinkpolymersystems.co.uk Skype: shrinkpolymersystems www.shrinkpolymersystems.co.uk 50 Heat Shrink Cable Entry Glands • Six sizes cover cable diameters from 4mm through to 70mm • Provides a watertight seal and secure fixing to gland plate/box • Ideal for non armoured (except PICAS) power or fibre optic cables • Approved and used by various UK regional electricity companies for use on 95-300mm² 11kV PICAS cables • Flame retardant The HCS series of heat shrinkable cable entry glands were developed to provide a cost effective method of providing a weatherproof seal on a wide variety of cables. The glands are manufactured in accordance with MIL-1- 81765/1 and MIL-1-23053/15 specifications and provide a flame retarded adhesive lined body along with a male threaded part to enable fixture to the gland plate. The range comprises six different sizes as detailed below. Ref No Cable O/D max Cable O/D min Bulkhead Thickness Max Length Rec Drill Hole HCS 1 12mm 4mm 6mm 95mm 26mm HCS 2 17mm 7mm 6mm 95mm 26mm HCS 3 26mm 13mm 6mm 100mm 35mm HCS 4 38mm 19mm 6mm 130mm 51mm HCS 4s 53mm 19mm 10mm 170mm 60mm HCS 5 70mm 36mm 6mm 200mm 88mm