This document provides information on PP and PPA flat profile marking products produced by Partex for on-site printing. PP is a flat hard profile for wire/cable marking, while PPA has an adhesive backing. Both profiles can be printed and used from -20°C to +60°C. PPA has a strong adhesive that adheres well to various surfaces both immediately and over time. The profiles are intended to be printed on site using the Partex ProMark MK9 printer.
Since the loads having the trends towards growing density. This requires the better appearance, rugged construction, greater service reliability and increased safety. An underground cable essentially consists of one or more conductors covered with suitable insulation and surrounded by a protecting cover. The interference from external disturbances like storms, lightening, ice, trees etc. should be reduced to achieve trouble free service. The cables may be buried directly in the ground, or may be installed in ducts buried in the ground.
Since the loads having the trends towards growing density. This requires the better appearance, rugged construction, greater service reliability and increased safety. An underground cable essentially consists of one or more conductors covered with suitable insulation and surrounded by a protecting cover. The interference from external disturbances like storms, lightening, ice, trees etc. should be reduced to achieve trouble free service. The cables may be buried directly in the ground, or may be installed in ducts buried in the ground.
Keytech 3D Printing filaments are made with high special polymers, mostly never use in
3D Printing till today.
These filament are made with high thermal and mechanical characteristics.
Particular attention are PolyKey PLA HS and PolyKey PLA HS NX who have a similar
thermal and mechanical characteristics of ABS and PA but are possible and easy to print
like PLA.
Others new polymers are PP (Polypropylene) Special Compound with high thermal and
mechanical characteristics better of ABS and PA, aren't biopolymers and in meantime
have also very low moisture absorption and will be to print similar PLA.
On the next page you can see a best values and points of Keytech 3D Printing Filament.
OverTec is a low pressure overmoulding system that positions between high pressure short cycle time processes for mass production and gravity fed, long cycle time processes for short runs and prototypes. It is a very cost effective way to seal and protect electronic components. Popular applications include connector potting, overmoulding PCBs, making electric cable glands, providing strain relief on cables and protecting sensors.
Medium Voltage Terminations- up to 42kV.| AKBAR TRADING EST.| mail@akbartradi...AKBAR TRADING
Cold Applied:
• TFTI-TFTO:
Single Core Polymeric Cable Termination - Pre Expanded on Holdout - up to 42kV
• TFTI-TFTO:
Single Core Polymeric Cable Termination - Push On - up to 42kV
Heat Shrinkable:
• IXSU/OXSU:
Uniterm - Terminations for Polymeric Cables - up to
42kV
Uniterm - Terminations for Polymeric Cables - up to
42kV - Selection Guide
• IXSU/OXSU - EPKT Quick Reference Guide
Heat Shrinkable Elbows:
• EPKT:
Heat Shrinkable Termination System for cables up to 36kV
Heat Shrinkable Termination Selection Guide
• RSRB:
Inline Bushing Boots
• RSRB:
Right Angle Bushing Boots
Inline & Right Angle Bushing Boot Selection Guide
Push On Elbows:
• RCAB:
Elastomeric Flexible Bushing Boot - up to 17.5kV ONLY
• RCAB:
Inline Cold Applied Boot - up to 24kV ONLY
• RICS:
Insulated Elbow Adaptors - up to 24kV
Insulated Elbow Adaptors - up to 24kV - Selection Guide
• RSES/RSSS:
Insulated Screened Elbows - 250A - up to 24kV
• RSTI:
Insulated Screened Elbows - 630A - up to 24kV
• RSTI:
Insulated Screened Elbows - 630A - up to 36kV
• RSTI:
Insulated Screened Elbow - Piggyback Coupling System - up to 36kV
GURO MV:
NEW
GUROFLEX Medium Voltage - Cold pour Insulating Compound
Section 4:
Energy Division
http://energy.tycoelectronics.com
Keytech 3D Printing filaments are made with high special polymers, mostly never use in
3D Printing till today.
These filament are made with high thermal and mechanical characteristics.
Particular attention are PolyKey PLA HS and PolyKey PLA HS NX who have a similar
thermal and mechanical characteristics of ABS and PA but are possible and easy to print
like PLA.
Others new polymers are PP (Polypropylene) Special Compound with high thermal and
mechanical characteristics better of ABS and PA, aren't biopolymers and in meantime
have also very low moisture absorption and will be to print similar PLA.
On the next page you can see a best values and points of Keytech 3D Printing Filament.
OverTec is a low pressure overmoulding system that positions between high pressure short cycle time processes for mass production and gravity fed, long cycle time processes for short runs and prototypes. It is a very cost effective way to seal and protect electronic components. Popular applications include connector potting, overmoulding PCBs, making electric cable glands, providing strain relief on cables and protecting sensors.
Medium Voltage Terminations- up to 42kV.| AKBAR TRADING EST.| mail@akbartradi...AKBAR TRADING
Cold Applied:
• TFTI-TFTO:
Single Core Polymeric Cable Termination - Pre Expanded on Holdout - up to 42kV
• TFTI-TFTO:
Single Core Polymeric Cable Termination - Push On - up to 42kV
Heat Shrinkable:
• IXSU/OXSU:
Uniterm - Terminations for Polymeric Cables - up to
42kV
Uniterm - Terminations for Polymeric Cables - up to
42kV - Selection Guide
• IXSU/OXSU - EPKT Quick Reference Guide
Heat Shrinkable Elbows:
• EPKT:
Heat Shrinkable Termination System for cables up to 36kV
Heat Shrinkable Termination Selection Guide
• RSRB:
Inline Bushing Boots
• RSRB:
Right Angle Bushing Boots
Inline & Right Angle Bushing Boot Selection Guide
Push On Elbows:
• RCAB:
Elastomeric Flexible Bushing Boot - up to 17.5kV ONLY
• RCAB:
Inline Cold Applied Boot - up to 24kV ONLY
• RICS:
Insulated Elbow Adaptors - up to 24kV
Insulated Elbow Adaptors - up to 24kV - Selection Guide
• RSES/RSSS:
Insulated Screened Elbows - 250A - up to 24kV
• RSTI:
Insulated Screened Elbows - 630A - up to 24kV
• RSTI:
Insulated Screened Elbows - 630A - up to 36kV
• RSTI:
Insulated Screened Elbow - Piggyback Coupling System - up to 36kV
GURO MV:
NEW
GUROFLEX Medium Voltage - Cold pour Insulating Compound
Section 4:
Energy Division
http://energy.tycoelectronics.com
The full Partex product catalogue. It has detailed descriptions of each product including; specifications, overviews and pictures.
Visit www.partex.co.uk or http://www.partex-direct.co.uk for prices and availability.
1. 2011-10-03
Production on site
PP/PPA
FLAT PROFILE
• PP is a flat hard profile suited for PT+, PTC, PTM and
PM sleeves
• PPA is a flat hard profile with adhesive tape for
cabinet and component marking
• Some PP-sizes have been specially developed to
fit some of the most common brands of terminal
blocks. These sizes are available only in white.
• The tape of the PPA provides a highly secure
adhesion on structured surfaces etc.
• Developed for easy printing on site in the ProMark
MK9 system
Packaging
Standard is the compactadisc reel in the ProMark
system.
Temperature range
From –20°C to +60°C (–4°F to +140°F).
General information
Design
PP and PPA is a profile which could be used for wire,
cable, circuit card and component marking. The profile
can be used with sleeves or mounted directly on the
circuit card or component.
Stocking temperature
+20°C (+68°F).
In order to achieve the best results, the PP and the
PPA should have been printed and mounted 9 months
after the production date.
Printed and mounted profiles are not affected by this
PPA has a strong double-sided adhesive tape, which
consists of a PVC protection paper with a modified
acrylic adhesive. The profile has a hardness combined
with a steady extruded surface that makes it ideal for
thermo transfer printing
Resistance PP-profile
The product has been tested according to Partex
Product Test Program by the Swedish Test and
Research Institute and has the following test
properties:
NOTE: For the PPA should have the best adhesion is
important to clean the surface thoroughly, preferably
with spirits
-
-
-
-
-
-
Material
The PPA profile is made of semi hard, cadmium and
silicon free PVC. The double sided tape has a special
high tack acrylic adhesive.
Flammability resistance according to UL94-V0.
For use indoors/in closed spaces outdoors.
Text resistant to UV radiation,
Text resistant to wear.
Resistant to temperature and ageing.
Resistant to chemicals according to Partex TestProgram.
Colours
White or yellow.
Some PP-sizes are only available in white
Printing equipment Partex ProMark MK9 machine and
profile feeding from the compactadisc packing.
For application in hostile enviroments, please contact
Partex for information.
Print
Intended for printout in the ProMark MK9 marking
printer.
NB: Please note test has so far only been carried out
for the PP-profile exclusive the double sided adhesive
tape!
2. 2011-10-03
Application
Terminal blocks with PP-profile
A PP-profile in a PTC sleeve mounted on
a CAT 5 cable
PPA-profile mounted on a component
Product and ordering information
Profile
Article number
Information
Profile width
Compactadisc pack unit
PP-04600SN*
Flat profile fits PT+, PTC and PTM sleeves
4.6 mm
15 m
PP-09000SN*
Flat profile, fits PM sleeves
9.0 mm
18 m
PP-06300SN9
Flat profile, fits Phoenix terminal blocks UT2.5, UTTB2.5, ST4, DT2.5, QTC, DTI2.5
6.3 mm
15 m
PP-10000SN9
Flat profile, fits entrelecs terminal blocks
10.2 mm
15 m
PP-11000SN9
Flat profile, fits Wago TopJobs terminal blocks
11.0 mm
12 m
PPA09000SN*
Flat profile with adhesive
9.0 mm
10 m
Accessories
Article number
Information
MK9-NG-KIT1
MK9 ProMark thermal printer
MK9-CAS46
Profile guide cassette for PP-046
MK9-CAS63
Profile guide cassette for PP-063
MK9-CAS90
Profile guide cassette for PP-090/PPA090
Technical data - Adhesive tape (PPA)
Peel adhesion on different surfaces
Material
Immediately N/cm
After 14 days N/cm
13.5
14.8
9.4
12.4
ABS
10.9
13.7
PC
13.5
13.8
PS
10.5
12.2
PET
9.4
10.7
PVC
9.3
13.5
PP
6.9
8.7
PE
5.5
Steel
Aluminium
Temperature resistance
Short term use
Long term use
Mechanical properties
Tensile strength
Elongation
5.8
Value
70ºC
60ºC
Value
≥57.5 N / 15 mm
20 – 55%