Dokumen tersebut memberikan informasi mengenai penggunaan baja organik Taaveekun dan amalan pertanian yang lestari untuk meningkatkan hasil tanaman secara organik. Dokumen ini juga menyoroti keberhasilan penggunaan baja Taaveekun dalam meningkatkan pertumbuhan dan hasil berbagai tanaman seperti sayuran, buah-buahan, dan komoditi pertanian lainnya.
Dokumen tersebut memberikan informasi mengenai produk baja organik TAAVEEKUN yang menggunakan teknologi dari Thailand dan Jepun. Produk ini mengandungi unsur hara seimbang beserta mikroorganisma dan enzim yang dapat memperbaiki sifat fizikal, kimia dan biologi tanah serta meningkatkan hasil tanaman. Dokumen ini juga menyarankan penggunaan baja organik secara berkesinambungan untuk menggantikan penggunaan racun yang
Dokumen tersebut merangkum produk baja organik TAAVEEKUN yang menggunakan teknologi Thailand untuk meningkatkan kesuburan tanah dan hasil tanaman. Produk ini mengandungi unsur hara seperti nitrogen, fosforus, kalsium dan magnesium serta enzim dan hormon yang membantu pertumbuhan tanaman. Ia juga mampu memperbaiki sifat fizikal, kimia dan biologi tanah untuk meningkatkan daya penyerapan hara oleh akar tanaman.
Good soil management practices in oil palm production include maintaining soil quality by focusing on key properties like fertility and minimizing environmental impact. The document recommends using biological, organic, and chemical fertilizers as well as soil amendments and conditioners to create productive soil. It also suggests applying a chitosan and biological extract foliar spray to oil palm seedlings, foliage, and surrounding soil every 1-2 months as chitosan has antimicrobial properties that can inhibit virus propagation and enhance the plant's immune response to infection.
Dokumen tersebut memberikan informasi mengenai penggunaan baja organik Taaveekun dan amalan pertanian yang lestari untuk meningkatkan hasil tanaman secara organik. Dokumen ini juga menyoroti keberhasilan penggunaan baja Taaveekun dalam meningkatkan pertumbuhan dan hasil berbagai tanaman seperti sayuran, buah-buahan, dan komoditi pertanian lainnya.
Dokumen tersebut memberikan informasi mengenai produk baja organik TAAVEEKUN yang menggunakan teknologi dari Thailand dan Jepun. Produk ini mengandungi unsur hara seimbang beserta mikroorganisma dan enzim yang dapat memperbaiki sifat fizikal, kimia dan biologi tanah serta meningkatkan hasil tanaman. Dokumen ini juga menyarankan penggunaan baja organik secara berkesinambungan untuk menggantikan penggunaan racun yang
Dokumen tersebut merangkum produk baja organik TAAVEEKUN yang menggunakan teknologi Thailand untuk meningkatkan kesuburan tanah dan hasil tanaman. Produk ini mengandungi unsur hara seperti nitrogen, fosforus, kalsium dan magnesium serta enzim dan hormon yang membantu pertumbuhan tanaman. Ia juga mampu memperbaiki sifat fizikal, kimia dan biologi tanah untuk meningkatkan daya penyerapan hara oleh akar tanaman.
Good soil management practices in oil palm production include maintaining soil quality by focusing on key properties like fertility and minimizing environmental impact. The document recommends using biological, organic, and chemical fertilizers as well as soil amendments and conditioners to create productive soil. It also suggests applying a chitosan and biological extract foliar spray to oil palm seedlings, foliage, and surrounding soil every 1-2 months as chitosan has antimicrobial properties that can inhibit virus propagation and enhance the plant's immune response to infection.
The document summarizes Malaysia's furniture trade from 2004-2007. It shows that Malaysia's total furniture exports grew from RM7.05 billion in 2004 to RM8.55 billion in 2007. The top export destination was the USA, though its share declined in 2007. Wooden furniture comprised the majority of exports, with wooden seats and office furniture being the fastest growing segments. Imports remained relatively flat during this period.
The document summarizes Malaysia's trade performance and furniture exports from 2004-2007. Total Malaysian exports grew around 3-5% annually while furniture exports grew around 6-8% yearly over this period. The top export destinations for Malaysian furniture were the US, Japan, Australia, and others, with wooden and metal furniture comprising the majority of exports. Office and kitchen furniture saw some of the strongest export growth rates to countries like India, UAE, and Australia.
The document lists various furniture leg and caster fittings including stamped steel claw foot toe caps, bun feet in various styles, diameters and heights, sofa and queen anne legs, casters with wood or porcelain wheels in different sizes, and nails. Dimensions and load capacities are provided for each fitting type.
The document describes various types of fasteners and furniture fittings including nails, decorative nails, bed hardware, bail pulls, bin pulls, and bells. It provides details on the materials, sizes, finishes, and intended uses of over 50 different fastener and fitting products. The products are for general woodworking and furniture making/repair applications.
The document describes various types of fasteners and fittings for furniture including nails, tacks, rivets, screws, mirror brackets, and mirror mounts. It provides specifications for different sizes of brass plated and plain steel trunk nails and tacks, brass plated split rivets, brass and steel screw posts, black and plated steel screws, antique brass and nickel plated mirror brackets, brass plated steel rear mount mirror supports, cast brass and antique brass cheval mirror mounts, and surface mounting clips. Directions are also provided for using split rivet caps.
The document lists various types of furniture fittings and accessories including dowel rods, dowel pins, dowel centers, butterfly hinges, flush mount hinges, drop leaf table hinges, concealed hinges, hinges, strap hinges, pivot hinges, lift off hinges, trunk hinges, ice box hardware, trunk lid stays, rollers, studs, trunk locks, drawbolts, and catches. The items are made of materials like hardwood, brass, steel, and bronze. Sizes vary with the specific fitting or accessory described.
The document lists and provides specifications for various furniture parts and accessories. It includes details on chair parts like heavy duty swivel bases, rocker bases, and oak rocker runners. It also lists high chair parts, tray arms, safety straps, as well as finials, spindles and pegs of various sizes. Measurements are provided for length, width, thickness and diameters. Materials include steel, oak, pine and leather.
This document lists various types of mouldings, beading, trim, and pressed wood ornaments available for sale. It provides specifications for half round and full round rope trim, beading, dentil moulding, and pressed wood ornaments in different sizes, widths, diameters, and wood types including maple, oak, birch, and walnut. Mouldings are available individually or in pairs.
The document lists various furniture fittings and accessories including brass knobs, wood knobs, drawer pulls, catches, and antique pulls. It provides the dimensions and materials of each fitting. The listings include the diameter, projection, and other relevant measurements of each item. A wide variety of styles and sizes of knobs, pulls, and other fittings are described.
The document provides an organization chart for a manufacturing operation. It shows that the Operation Chief Executive oversees the Operation Manager, who oversees the Factory Manager. Under the Factory Manager are positions like Production Planning & Control, Production Manager, Material Manager, Maintenance & Engineering, and Research & Design. The chart also lists some roles under Production Manager like QC, Tally, QC Inventory, and Tooling.
The document outlines the responsibilities of a materials controller in a furniture manufacturing factory, including receiving, inspecting, storing, maintaining, and distributing raw materials and ensuring proper documentation and inventory controls are followed. Key requirements for the role include knowledge of materials, management processes, and record keeping systems. Proper storage and handling of different material types is also discussed based on their physical properties.
The document discusses the benefits of using paste wax to protect and maintain wood furniture finishes. It provides perspectives from woodworking experts who recommend using wax as the best choice for furniture care. Wax forms a protective layer that prevents superficial scratches and dents from damaging the underlying finish. It also helps prevent dust from sticking to furniture surfaces. The document provides tips on applying and maintaining wax finishes on wood furniture.
This document discusses different types of veneer available for woodworking projects. It describes standard veneer, which is cut into thin sheets and sold by the square foot, and flexible veneer, which is manufactured into wide, thin, and flexible sheets for easier application. Standard veneer requires more preparation like sanding and jointing of multiple narrow sheets, while flexible veneer is pre-flattened and jointed but more expensive. The document also provides instructions for cutting veneer with a veneer saw or craft knife, and edge jointing sheets of standard veneer using a homemade jig to ensure a tight seam.
This document provides information about shellac flakes and how to mix and apply shellac as a finish. It describes different types of shellac flakes like seed lac, button lac, garnet lac, and lemon yellow. It explains how to mix shellac flakes with denatured alcohol at different "cuts" or concentrations. Application tips are given, such as applying multiple thin coats, using a retarder to reduce brush marks, and sanding between coats. Final rubbing and waxing of the dried shellac finish is also outlined.
This document provides instructions for using rottenstone and pumice to polish and finish wood surfaces. Rottenstone can be used as the final polishing compound to produce a high gloss finish on lacquer, varnish and shellac. It is also used to antique gilt finishes and dust mats. Pumice comes in varying grit sizes and can be used to hand rub wood finishes to a matte surface in preparation for polishing with rottenstone. The instructions describe the supplies needed, preparation of the wood surface, lubricating with oil or water, rubbing technique, and allowing time for the finish to harden before applying protective wax.
French polishing is a process of coating wood with shellac dissolved in alcohol using a "rubber" made of rag and cotton wool. It produces a fine looking finish for furniture. The process involves bodying in the shellac to fill pores, building up layers, and spiriting out for a high gloss finish. Proper preparation of the wood surface is important for a smooth result.
The document provides instructions for preparing furniture for refinishing. It explains that the first step is to remove all old finish from the furniture by using a commercial paint or varnish remover and carefully scraping it off with a putty knife or scraper. It notes to be careful when removing finish from veneered surfaces to avoid damaging the wood. It also recommends washing the surface after removing the old finish. The next steps involve allowing the wood to dry completely before sanding it smooth to prepare for a new finish.
The document provides tips for furniture finishing and repair. It discusses how to remove waxy build-up, hide light scratches, paint over an existing finish, remove white spots from water, and tips for handling and moving furniture. Key points include using mineral spirits or steel wool to remove waxy build-up, using padding lacquer or polishing compounds to hide light scratches, thorough sanding and cleaning when painting over a finish, and using steel wool or oils to remove white spots from water damage.
The document shows a diagram of a palm tree with labeled measurements for different parts of the tree. The trunk is 7.8 meters tall and branches begin 9 meters from the base. The fronds extend out 2.4 meters from the branches.
The document summarizes Malaysia's furniture trade from 2004-2007. It shows that Malaysia's total furniture exports grew from RM7.05 billion in 2004 to RM8.55 billion in 2007. The top export destination was the USA, though its share declined in 2007. Wooden furniture comprised the majority of exports, with wooden seats and office furniture being the fastest growing segments. Imports remained relatively flat during this period.
The document summarizes Malaysia's trade performance and furniture exports from 2004-2007. Total Malaysian exports grew around 3-5% annually while furniture exports grew around 6-8% yearly over this period. The top export destinations for Malaysian furniture were the US, Japan, Australia, and others, with wooden and metal furniture comprising the majority of exports. Office and kitchen furniture saw some of the strongest export growth rates to countries like India, UAE, and Australia.
The document lists various furniture leg and caster fittings including stamped steel claw foot toe caps, bun feet in various styles, diameters and heights, sofa and queen anne legs, casters with wood or porcelain wheels in different sizes, and nails. Dimensions and load capacities are provided for each fitting type.
The document describes various types of fasteners and furniture fittings including nails, decorative nails, bed hardware, bail pulls, bin pulls, and bells. It provides details on the materials, sizes, finishes, and intended uses of over 50 different fastener and fitting products. The products are for general woodworking and furniture making/repair applications.
The document describes various types of fasteners and fittings for furniture including nails, tacks, rivets, screws, mirror brackets, and mirror mounts. It provides specifications for different sizes of brass plated and plain steel trunk nails and tacks, brass plated split rivets, brass and steel screw posts, black and plated steel screws, antique brass and nickel plated mirror brackets, brass plated steel rear mount mirror supports, cast brass and antique brass cheval mirror mounts, and surface mounting clips. Directions are also provided for using split rivet caps.
The document lists various types of furniture fittings and accessories including dowel rods, dowel pins, dowel centers, butterfly hinges, flush mount hinges, drop leaf table hinges, concealed hinges, hinges, strap hinges, pivot hinges, lift off hinges, trunk hinges, ice box hardware, trunk lid stays, rollers, studs, trunk locks, drawbolts, and catches. The items are made of materials like hardwood, brass, steel, and bronze. Sizes vary with the specific fitting or accessory described.
The document lists and provides specifications for various furniture parts and accessories. It includes details on chair parts like heavy duty swivel bases, rocker bases, and oak rocker runners. It also lists high chair parts, tray arms, safety straps, as well as finials, spindles and pegs of various sizes. Measurements are provided for length, width, thickness and diameters. Materials include steel, oak, pine and leather.
This document lists various types of mouldings, beading, trim, and pressed wood ornaments available for sale. It provides specifications for half round and full round rope trim, beading, dentil moulding, and pressed wood ornaments in different sizes, widths, diameters, and wood types including maple, oak, birch, and walnut. Mouldings are available individually or in pairs.
The document lists various furniture fittings and accessories including brass knobs, wood knobs, drawer pulls, catches, and antique pulls. It provides the dimensions and materials of each fitting. The listings include the diameter, projection, and other relevant measurements of each item. A wide variety of styles and sizes of knobs, pulls, and other fittings are described.
The document provides an organization chart for a manufacturing operation. It shows that the Operation Chief Executive oversees the Operation Manager, who oversees the Factory Manager. Under the Factory Manager are positions like Production Planning & Control, Production Manager, Material Manager, Maintenance & Engineering, and Research & Design. The chart also lists some roles under Production Manager like QC, Tally, QC Inventory, and Tooling.
The document outlines the responsibilities of a materials controller in a furniture manufacturing factory, including receiving, inspecting, storing, maintaining, and distributing raw materials and ensuring proper documentation and inventory controls are followed. Key requirements for the role include knowledge of materials, management processes, and record keeping systems. Proper storage and handling of different material types is also discussed based on their physical properties.
The document discusses the benefits of using paste wax to protect and maintain wood furniture finishes. It provides perspectives from woodworking experts who recommend using wax as the best choice for furniture care. Wax forms a protective layer that prevents superficial scratches and dents from damaging the underlying finish. It also helps prevent dust from sticking to furniture surfaces. The document provides tips on applying and maintaining wax finishes on wood furniture.
This document discusses different types of veneer available for woodworking projects. It describes standard veneer, which is cut into thin sheets and sold by the square foot, and flexible veneer, which is manufactured into wide, thin, and flexible sheets for easier application. Standard veneer requires more preparation like sanding and jointing of multiple narrow sheets, while flexible veneer is pre-flattened and jointed but more expensive. The document also provides instructions for cutting veneer with a veneer saw or craft knife, and edge jointing sheets of standard veneer using a homemade jig to ensure a tight seam.
This document provides information about shellac flakes and how to mix and apply shellac as a finish. It describes different types of shellac flakes like seed lac, button lac, garnet lac, and lemon yellow. It explains how to mix shellac flakes with denatured alcohol at different "cuts" or concentrations. Application tips are given, such as applying multiple thin coats, using a retarder to reduce brush marks, and sanding between coats. Final rubbing and waxing of the dried shellac finish is also outlined.
This document provides instructions for using rottenstone and pumice to polish and finish wood surfaces. Rottenstone can be used as the final polishing compound to produce a high gloss finish on lacquer, varnish and shellac. It is also used to antique gilt finishes and dust mats. Pumice comes in varying grit sizes and can be used to hand rub wood finishes to a matte surface in preparation for polishing with rottenstone. The instructions describe the supplies needed, preparation of the wood surface, lubricating with oil or water, rubbing technique, and allowing time for the finish to harden before applying protective wax.
French polishing is a process of coating wood with shellac dissolved in alcohol using a "rubber" made of rag and cotton wool. It produces a fine looking finish for furniture. The process involves bodying in the shellac to fill pores, building up layers, and spiriting out for a high gloss finish. Proper preparation of the wood surface is important for a smooth result.
The document provides instructions for preparing furniture for refinishing. It explains that the first step is to remove all old finish from the furniture by using a commercial paint or varnish remover and carefully scraping it off with a putty knife or scraper. It notes to be careful when removing finish from veneered surfaces to avoid damaging the wood. It also recommends washing the surface after removing the old finish. The next steps involve allowing the wood to dry completely before sanding it smooth to prepare for a new finish.
The document provides tips for furniture finishing and repair. It discusses how to remove waxy build-up, hide light scratches, paint over an existing finish, remove white spots from water, and tips for handling and moving furniture. Key points include using mineral spirits or steel wool to remove waxy build-up, using padding lacquer or polishing compounds to hide light scratches, thorough sanding and cleaning when painting over a finish, and using steel wool or oils to remove white spots from water damage.
The document shows a diagram of a palm tree with labeled measurements for different parts of the tree. The trunk is 7.8 meters tall and branches begin 9 meters from the base. The fronds extend out 2.4 meters from the branches.
9. 1. Rendam surat khabar dalam air yang
mempunyai Asid Amino TaaVeeKun Super
selama 4 jam (50ml+20l air)
2. Susun biji benih lada didalam surat
khabar yang telah direndam
3. Gulung surat khabar dan masukkan
kedalam plastik cerah
4. Hembus udara kedalam plastik hingga
menggelembung dan ikat dengan
sempurna
5. Jemur dibawah cahaya matahari selama 36
jam
10. 1. Masukkan campuran media asas ke
dalam poly bag
2. Pindahkan anak benih ke dalam poly
bag (kerek)
3. Taburkan soil amendment 10gm di
dalam polibag ( Setiap 2 Minggu)
4. Sembur Asid amino Taaveekun Super
Setiap 7 hingga 10 Hari
11. 1. Menyediakan lubang tanaman
2. Pindahkan anak benih (dari dalam poly bag) ke
dalam lubang/ palong
3. Masukan 20-30g soil amendment selepas 5 hari
ditanam. Ulang setiap 7-10 hari sekali.
4. Semburkan Taaveekun Super Gold (40ml + 20 L
air) di pangkal & kawasan akar 6 hari Selepas
Ditanam. Ulang Setiap 10-14 hari.
5. Semburkan TVK vinegar Super 40ml + 40ml
Taaveekun Super 3 + 20 L air dan sembur pada
daun, ranting & batang pokok.
12. TEMPOH ALIH BAJA / RACUN SUKATAN
KE LADANG (20 ltr Air)
1. Taa Vee Kun asid amino Super 30 ml
Hari ke 5 2. Uniform 10 ml
3. RH Cyper @(-cypermethrin) 17 ml
4. Cabryl- (cerbaryl) 20 gm
1. Uniform 10 ml
Hari ke 10 2. Confidor-(-imidachloprid) 5 ml
3. Mankozeb(-mancozeb) 25 gm
1. TVK Vinegar Super + Super 3 30 ml
Hari ke 15 2. Uniform 10 ml
3. Avemec-(abamethin) 17 ml
4. Carabin-(proclorax zink complex) 11 gm
Hari ke 20 1. Uniform 10 ml
2. RH Cyper @ 17 ml
3. Cabryl 20 gm
Hari ke 25 1. Uniform 10ml
(Bila Bunga Keluar) 2. Calbomeg 10ml
3. TVK Vinegar Super + Super 3 40ml
4. TaaVeeKun Super Gold 40ml
5. Mitac (amitraz) 22ml
6. Carabin 11gm
13. TEMPOH
ALIH KE BAJA / RACUN SUKATAN
LADANG
(20 ltr Air)
Hari ke 30 1. Uniform 10ml
2. Confidor 5ml
Hari ke 35 1. Uniform 10ml
2. TVK vinegar Super 30ml
3. Taaveekun Super 3 30ml
4. Taaveekun Super Gold 40ml
5. Geberdim 2ml
6. Benlete 7gm
7. Avemec-abamethin
Hari ke 40 1. Uniform 10ml
2. RH Cyper @ 17ml
3. Cabryl 20gm
Hari ke 45 1. Uniform 10ml
2. TVK vinegar Super 10ml
3. Taaveekun Super 3 30ml
4. Taaveekun Super Gold 20ml
5. Geberdim 2ml
6. Benlete 7gm
7. Avemec
NOTA : Baja TAA VEE KUN soil amendment hendaklah ditabur setiap 7 hari sekali
14. 1.Kawal Aphid (Kutu Daun) dengan
Confidor
2.Kawal Hamama Merah (Red Spider
Mites) dengan Abamecthin dan Mitec
3.Kawal Lalat Buah (Fruit Fly) dengan
Cypermethrin dan Deltamethrin
4.Kawal Lalat Putih (White Fly) dengan
Confidor dan Abamecthin
15. 1. Tabur Benih Maman di Keliling Kawasan Sempadan
dan sekitar Kawasan Penanaman Cabai
2. Semakin Pokok Maman Berbunga, Semakin banyak
Serangga yang akan Berkumpul
3. Tanam Jagung di Kawasan Sempadan Sebagai
Perangkap Kedua
4. Buat operasi Kawalan Semburan Di Waktu Senja Untuk
Membunuh Serangga Yang Berkumpul Pada Pokok
Jagung dan Benih Maman
5. Pemantauan Pada Tanaman Cabai Perlu Dilakukan
Untuk Membunuh Serangga Yang Terlepas dari
Perangkap