2. PAINT AID
€ 80 148 ‘ (2 u 28’)
Charlotte De Ruytter
http://speelmat2011.blogspot.com/ Wouter Velle
Paulina Hernandez Santamaria
http://designforeveryone.howest.be/
4. PAINT AID
BILL OF MATERIAL
4 quickstep
2 metal pipe (diameter 22mm length 70cm)
2 wheel chair supports
2 quickstep supports (arm rest)
2 quickstep supports (next arm rest)
2 quickstep connection (board-pipe)
6 screws (diameter 5 mm)
6 nuts (diameter 5 mm)
6 washers (diameter 5 mm)
1 bag (supports)
1 bag (paint)
1 paper holder
4 ribbon holders
Velcro
Press buttons
Rubber
Glue, scissors, thread, needle.
Tweezers
Jigsaw
Drill
Drill bits (9mm, 5mm)
Press
Screwdriver
Tape measure
Double sided tape
15 tools
3
21
5.
6. 1 PAINT AID
DESCRIPTION
Confirm you have 2 table attachment pipes
on each side of the wheelchair, if not, you
can buy them easily at an wheelchair supply
store. Attach to the wheelchair.
No plan needed
5’
Screwdriver
Attachment pipes for the weelchair
2
Depending on the needs
7. 2 PAINT AID
DESCRIPTION
Put the 2 metal tubes into each attachment
pipe.
No plan needed
1’
No tools needed
2 metal tubes
2
€ 19,60
8. 3 PAINT AID
DESCRIPTION
Measure the distance between the 2 pipes
(center to center) and add 10cm. Write this
distance down because you will need it to cut
the boards.
No plan needed
1’
Tapeline
No parts bought
No parts added
€0
9. 4 PAINT AID
DESCRIPTION
Cut the quickstep to get 4 pieces of the
obtained measurement. (as described in step
3).
Cut 6 pieces of 17cm long quickstep.
For clean edges it is best to use a buzz saw but if
you don’t have one, you can also use a jigsaw.
No plans needed
10’
Saw
Quickstep boards
10
€ 33,59
10. 5 PAINT AID
DESCRIPTION
Tape the 17 cm long pieces together with the
double sided tape in groups of two. Make
sure you only tape on the backside.
No plans needed
4’
Double sided tape
Double sided tape
0
€ 10,49
11. 6 PAINT AID
DESCRIPTION
Print plan A twice, plan B, C and D once and
cut them out roughly.
Plans A & B needed
3’
Printer, computer
No parts bought
0
€0
12. 7 PAINT AID
DESCRIPTION
Tape the printed plans onto the pieces.
No plans needed
1’
Double sided tape
No parts bought
0
€0
13. 8 PAINT AID
DESCRIPTION
Drill the required holes on plan B (diameter
9mm)
Plan B needed
4’
Drill, woodbit (diameter 9 mm), screw clamp
No parts bought
0
€0
14. 9 PAINT AID
DESCRIPTION
Saw plan A & B on the provided guidelines
using a jig saw. Plan A is a plan made
especially for Ludwiene’s wheelchair. It is
possible that you have to change some
dimensions.
Plan A & B needed
10’
Jig Saw, screw clamp
No parts bought
0
€0
15. 10 PAINT AID
DESCRIPTION
File the holes clean.
Plan B needed
5’
Wood file
No parts bought
0
€0
16. 11 PAINT AID
DESCRIPTION
Detach the taped pieces and remove the
plans.
When ready remove the two parts from
eachother. Now you have 2 equal pieces
from plan B and 4 pieces from plan A.
When needed, sandpaper the edges of the
pieces.
No plans needed
1’
No tools needed
No parst bought
0
€0
17. 12 PAINT AID
DESCRIPTION
Glue the pieces A back together with wood
glue and let them dry under pressure.
No plans needed
3’ action, 30’ drying
Screw clamps, woodglue
Wood glue
0
€ 2,50
18. 13 PAINT AID
Cut
DESCRIPTION
pieces of rubber.
Two times 16mm x 50mm, four times (16mm
x 45mm) and twice 16 mm x 15 mm
No plans needed
2’
Sharp knife of scissors
No parts bought
0
€0
19. 14 PAINT AID
DESCRIPTION
Glue the rubber into the attachment system
using superglue.
No plans needed
4’
Superglue
Superglue
2
€ 0,59 (Zeeman)
20. 14 PAINT AID
DESCRIPTION
Take a new board of quickstep and saw 2
pieces as noted on drawing C. Be sure you
use the good side of the board!
Plan C needed
5’
Saw
No parts bought
0
€0
21. PAINT AID
DESCRIPTION
15
Tape the paper pieces from drawing C onto
the two pieces of quickstep.
Plan C needed
1’
Double sided tape
No parts bought
0
€0
22. 16 PAINT AID
DESCRIPTION
Drill the hole as shown on the print. Be
carefull you position the hole correctly, a
wood-drill is better than a metal-drill.
(diameter: 5mm)
When drilling with a metal-drill we suggest to
drill a smaller hole first.
Plan C needed
5’
Drill, woodbit (diameter 5 mm)
No parts bought
0
€0
23. 17 PAINT AID
DESCRIPTION
Carefully, cut out the leaving part of the
wooden piece.
Plan C needed
4’
Saw, screw clamp
No parts bought
0
€0
24. 18 PAINT AID
DESCRIPTION
To make the bolts fit exactly into the wood,
you can carefully drill a tapered edge in al
the holes, this with a bigger drill.
No plans needed
3’
Wood glue
No parts bought
0
€0
25. 19 PAINT AID
DESCRIPTION
Glue pieces B and C together using wood
glue. Press hard.
No plans needed
3’ action, 30’ drying
Screw clamp
No parts bought
0
€0
26. 20 PAINT AID
DESCRIPTION
Remove the metal tubes from the wheelchair
and cut them at 60cm.
No plans needed
6’
Metal saw
No parts bought
0
€0
27. 21 PAINT AID
DESCRIPTION
Drill holes in the metal pipe as shown on
drawing D.
Plan D needed
18’
Drill, metal drill (diameter 5 mm)
No parts bought
0
€0
28. 22 PAINT AID
DESCRIPTION
Use the countersunk M8 bolts, washers and
nuts to put it all together.
Repeat for the second tube. When ready,
refix the tubes onto the wheelchair.
No plan needed
8’
Screwdriver
Countersunk M8 bolts, washers & nuts
3
€ 12
29. 23 PAINT AID
DESCRIPTION
Cut 3 pieces of white ribbon and one red
ribbon.
Create 2 corners of 90° and sew them
together. Do this for each ribbon. You can
choose the best length to make the handle.
No plans needed
10’
Needle, wire & ribbon
No parts bought
No parts added
€0
30. 24 PAINT AID
DESCRIPTION
Glue the ribbons to the boards. Be sure you
glue them at the right side. In the picture you
can see which side you have to glue them to.
Use screw clamps to let the glue dry under
pressure.
.
No plans needed
9’ action, 10’ drying
Superglue
No parts bought
No parts added
€0
31. 25 PAINT AID
DESCRIPTION
Now you have the four boards you need, you
still have to turn one board into a paint
palette.
The board with the red ribbon is the one that
we’re turning into a paint palette. Be sure you
use the right board to continue the next
steps.
.
No plans needed
0’
No tools needed
No parts bought
No parts added
€0
32. 26 PAINT AID
DESCRIPTION
Position a circle (diameter of your water cup)
on the Quickstep-board with the red ribon.
Drill a hole inside the circle.
No plan needed
10’
Drill & woodbit
No parts bought
0
€0
33. 27 PAINT AID
DESCRIPTION
Cut out the circle with a jig saw using the
hole from the previous step as a start point.
Sandpaper the hole.
No plan needed
12’
Jigsaw
No parts bought
0
€0
45. HOW TO USE TECHNICAL
ADDENDUM
The plans needed to be printed at scale 1:1. This
way you can easily cut them en tape them onto the
wood to saw/drill.
To print the plans, click on the attached links.
Plan A
Plan B
Plan C
Plan D
Extra’s:
Bags
Here is the principle of how the bags are made