This document provides instructions for removing an engine from a machine. It is a 33 step process that involves draining fluids, disconnecting wiring harnesses, removing hoses and belts, and then lifting the engine out after removing mounting bolts. Safety precautions are described at the beginning such as releasing pressure from hydraulic and brake systems.
Case 721 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, and mounting hardware to fully separate the engine for removal.
Case 821 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 33 steps for removing components to separate the engine from the rest of the machine, including draining fluids, disconnecting wiring harnesses, hoses and other connections, and removing mounting hardware. The overall process removes parts and accessories to fully separate the engine for removal while tagging components and connections for reinstallation.
New holland lw170 b wheel loader service repair manualujfjdjkskemme
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland lw170 b wheel loader service repair manual instant downloadudfjsjjekkekmem
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland u80 loader landscaper service repair manualjjdjfkkskemme
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- Copyright information and publication details
- A table of contents listing the manual sections and corresponding page numbers
- Section indexes providing the titles and numbers of sections within topics like General, Engine, Fuel System, etc.
- Specification details and troubleshooting guides for components like the engine, hydraulics, electrical systems, etc.
- Standard torque specifications for hardware and hydraulic fittings.
New holland u80 loader landscaper service repair manual instant downloadudjjskkemme
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- A table of contents listing the sections and publication numbers for topics like the engine, fuel system, electrical system, etc.
- Section indexes that provide the section numbers for topics within each system (e.g. engine removal, specifications, cooling system).
- Standard torque specifications for decimal and metric hardware, as well as hydraulic fittings.
- Notes about intended use and reservations to make improvements without obligation. Schematics are included in a rear pocket.
Case 621 f tier 4 wheel loader service repair manualyhfhjjkdksmme
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connections. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland w190 c tier 4 wheel loader service repair manualujdjjkskkmdme
The document provides instructions to remove the engine from a W190C Wheel Loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, removing the engine oil drain cap and draining oil, disconnecting wiring harnesses and hoses, and removing mounting bolts to separate the engine from the vehicle. Safety precautions are described such as releasing pressure from hydraulic circuits before draining fluids.
Case 721 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, and mounting hardware to fully separate the engine for removal.
Case 821 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 33 steps for removing components to separate the engine from the rest of the machine, including draining fluids, disconnecting wiring harnesses, hoses and other connections, and removing mounting hardware. The overall process removes parts and accessories to fully separate the engine for removal while tagging components and connections for reinstallation.
New holland lw170 b wheel loader service repair manualujfjdjkskemme
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland lw170 b wheel loader service repair manual instant downloadudfjsjjekkekmem
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland u80 loader landscaper service repair manualjjdjfkkskemme
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- Copyright information and publication details
- A table of contents listing the manual sections and corresponding page numbers
- Section indexes providing the titles and numbers of sections within topics like General, Engine, Fuel System, etc.
- Specification details and troubleshooting guides for components like the engine, hydraulics, electrical systems, etc.
- Standard torque specifications for hardware and hydraulic fittings.
New holland u80 loader landscaper service repair manual instant downloadudjjskkemme
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- A table of contents listing the sections and publication numbers for topics like the engine, fuel system, electrical system, etc.
- Section indexes that provide the section numbers for topics within each system (e.g. engine removal, specifications, cooling system).
- Standard torque specifications for decimal and metric hardware, as well as hydraulic fittings.
- Notes about intended use and reservations to make improvements without obligation. Schematics are included in a rear pocket.
Case 621 f tier 4 wheel loader service repair manualyhfhjjkdksmme
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connections. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland w190 c tier 4 wheel loader service repair manualujdjjkskkmdme
The document provides instructions to remove the engine from a W190C Wheel Loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, removing the engine oil drain cap and draining oil, disconnecting wiring harnesses and hoses, and removing mounting bolts to separate the engine from the vehicle. Safety precautions are described such as releasing pressure from hydraulic circuits before draining fluids.
Case 721 e tier 3 wheel loader service repair manualfjkskefksmeme
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components to separate the engine from the machine. Key steps include draining fluids, removing hoses, belts, wiring, guards, and finally disconnecting the engine mounts.
Case 721 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 34 detailed steps for disconnecting all electrical, mechanical and fluid connections to separate the engine from the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, shields, and other components to fully detach the engine.
Case 721 e tier 3 wheel loader service repair manualfjjsieskekfmmse
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. The goal is to fully separate the engine to allow it to be lifted out during maintenance or replacement.
CASE 721E Tier 3 Wheel Loader Service Repair Manual.pdffujskekmdmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 34 detailed steps for disconnecting all electrical, mechanical and fluid connections to separate the engine from the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, shields, and other components to fully detach the engine.
Case 721 e tier 3 wheel loader service repair manualfujsjefwekskemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, and finally disconnecting the engine mounts to allow the engine to be lifted out.
Case 821 e tier 3 wheel loader service repair manualfujsjefwekskemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for removal, including draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. The overall process involves preparing the machine, removing panels, tagging and disconnecting all engine connections and components in a specific order, and then lifting the engine from the machine.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
CASE 821E Tier 3 Wheel Loader Service Repair Manual.pdffujskekmdmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
New holland lw170 b wheel loader service repair manualfjskkddmmmse
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland lw170 b wheel loader service repair manualfusjejfjsekksem
This document provides the service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents outlining the manual's 10 tabs and their respective sections on topics like engines, steering, hydraulics, and mounted equipment.
- Index sections listing the section numbers and titles for each tab.
- Specification sections providing torque specifications for decimal and metric hardware, hydraulic fittings, and other components.
- Notes indicating CNH America reserves the right to make improvements and that the manual is printed in the U.S.A.
New holland lw170 b wheel loader service repair manualfjjsekekskmdm
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
Hyster e019 (h13.00 xm europe) forklift service repair manualfusjfjsekemwer
This document provides instructions for repairing the frame, counterweight, fenders, hood, hydraulic and fuel tanks, radiator/cooling section, operator compartment, and cab of certain Caterpillar lift trucks. It describes removing and installing the counterweight, which requires a crane due to its heavy weight. Procedures are provided for removing and installing fenders, the hood and air cleaner assembly, and the hydraulic tank. The document emphasizes safety precautions when working on or near heavy components, and when welding or using chemicals during the repair process.
Hyster d005 (h100 e americas) forklift service repair manualfusjfjsekemwer
1) The document provides information on servicing gear pumps used in hydraulic systems. It describes the components and operation of single-stage and tandem gear pumps.
2) The repair process begins with removing the pump, disassembling it, cleaning and inspecting parts. Worn seals are a common cause of failure. Replacement seals are recommended even for parts in good condition.
3) Reassembly involves lubricating parts and installing them back into the pump housings. Proper cleaning and care is important to prevent dirt from damaging parts or entering the hydraulic system.
Hyster c215 (w45 z) forklift service repair manualfusjfjsekemwer
The document provides instructions for repairing frames on forklifts. It describes the main components that attach to the frame, including the lifting mechanism, electrical system, hydraulic pump, and master drive unit. Procedures are outlined for separating a fork frame or drive unit frame if damaged while the rest of the truck is still usable. The steps include removing pins and carefully separating the frames. Reassembly involves replacing the pins in reverse order. Safety warnings are also provided.
Caterpillar cat 322 c l 322cl excavator (prefix bkm) service repair manual (b...fusjfjsekemwer
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 c s excavator (prefix bea) service repair manual (bea0000...fusjfjsekemwer
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It lists the required tools and outlines 7 steps to disassemble the valve, including removing bolts, fittings, seals, springs, and spools. Safety warnings are provided regarding relieving hydraulic pressure before disassembly and preventing contamination of hydraulic components.
Caterpillar cat 320 c s excavator (prefix bbl) service repair manual (bbl0000...fusjfjsekemwer
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
Caterpillar cat 320 c ln excavator (prefix bbl) service repair manual (bbl000...fusjfjsekemwer
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
This document provides instructions for disassembling and assembling the piston pump of a 216B3 Skid Steer Loader. It lists 71 steps to fully disassemble the pump by removing components like fittings, springs, seals, bearings, pins and plates. The assembly section lists 8 steps such as installing liners, seals, bearings and shafts. Tools required are also listed.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
This document provides instructions for disassembling and assembling the piston motor of a 216B3 Skid Steer Loader. The disassembly process involves removing 25 parts from the motor in a specific order, taking care when removing springs. The assembly process reverses the disassembly steps, heating some parts before installing and using tools to install retaining rings and shafts.
More Related Content
Similar to New holland w130 b tier 3 wheel loader service repair manual
Case 721 e tier 3 wheel loader service repair manualfjkskefksmeme
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components to separate the engine from the machine. Key steps include draining fluids, removing hoses, belts, wiring, guards, and finally disconnecting the engine mounts.
Case 721 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 34 detailed steps for disconnecting all electrical, mechanical and fluid connections to separate the engine from the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, shields, and other components to fully detach the engine.
Case 721 e tier 3 wheel loader service repair manualfjjsieskekfmmse
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. The goal is to fully separate the engine to allow it to be lifted out during maintenance or replacement.
CASE 721E Tier 3 Wheel Loader Service Repair Manual.pdffujskekmdmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 34 detailed steps for disconnecting all electrical, mechanical and fluid connections to separate the engine from the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, shields, and other components to fully detach the engine.
Case 721 e tier 3 wheel loader service repair manualfujsjefwekskemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, and finally disconnecting the engine mounts to allow the engine to be lifted out.
Case 821 e tier 3 wheel loader service repair manualfujsjefwekskemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for removal, including draining fluids, disconnecting wiring harnesses and hoses, and removing mounting hardware. The overall process involves preparing the machine, removing panels, tagging and disconnecting all engine connections and components in a specific order, and then lifting the engine from the machine.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
CASE 821E Tier 3 Wheel Loader Service Repair Manual.pdffujskekmdmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
New holland lw170 b wheel loader service repair manualfjskkddmmmse
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
New holland lw170 b wheel loader service repair manualfusjejfjsekksem
This document provides the service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents outlining the manual's 10 tabs and their respective sections on topics like engines, steering, hydraulics, and mounted equipment.
- Index sections listing the section numbers and titles for each tab.
- Specification sections providing torque specifications for decimal and metric hardware, hydraulic fittings, and other components.
- Notes indicating CNH America reserves the right to make improvements and that the manual is printed in the U.S.A.
New holland lw170 b wheel loader service repair manualfjjsekekskmdm
This document provides a service manual for a CNH America LLC LW 170.B Wheel Loader. It includes:
- Table of contents listing the manual's sections and corresponding page numbers.
- Sections covering general information such as torque specifications, fluids and lubricants, and a metric conversion chart.
- Sections covering specific vehicle systems and components including engines, fuel system, electrical, steering, power train, brakes, hydraulics, and mounted equipment.
- Copyright information for CNH America LLC and notes on the manual's publication and revision dates.
Similar to New holland w130 b tier 3 wheel loader service repair manual (11)
Hyster e019 (h13.00 xm europe) forklift service repair manualfusjfjsekemwer
This document provides instructions for repairing the frame, counterweight, fenders, hood, hydraulic and fuel tanks, radiator/cooling section, operator compartment, and cab of certain Caterpillar lift trucks. It describes removing and installing the counterweight, which requires a crane due to its heavy weight. Procedures are provided for removing and installing fenders, the hood and air cleaner assembly, and the hydraulic tank. The document emphasizes safety precautions when working on or near heavy components, and when welding or using chemicals during the repair process.
Hyster d005 (h100 e americas) forklift service repair manualfusjfjsekemwer
1) The document provides information on servicing gear pumps used in hydraulic systems. It describes the components and operation of single-stage and tandem gear pumps.
2) The repair process begins with removing the pump, disassembling it, cleaning and inspecting parts. Worn seals are a common cause of failure. Replacement seals are recommended even for parts in good condition.
3) Reassembly involves lubricating parts and installing them back into the pump housings. Proper cleaning and care is important to prevent dirt from damaging parts or entering the hydraulic system.
Hyster c215 (w45 z) forklift service repair manualfusjfjsekemwer
The document provides instructions for repairing frames on forklifts. It describes the main components that attach to the frame, including the lifting mechanism, electrical system, hydraulic pump, and master drive unit. Procedures are outlined for separating a fork frame or drive unit frame if damaged while the rest of the truck is still usable. The steps include removing pins and carefully separating the frames. Reassembly involves replacing the pins in reverse order. Safety warnings are also provided.
Caterpillar cat 322 c l 322cl excavator (prefix bkm) service repair manual (b...fusjfjsekemwer
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 c s excavator (prefix bea) service repair manual (bea0000...fusjfjsekemwer
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It lists the required tools and outlines 7 steps to disassemble the valve, including removing bolts, fittings, seals, springs, and spools. Safety warnings are provided regarding relieving hydraulic pressure before disassembly and preventing contamination of hydraulic components.
Caterpillar cat 320 c s excavator (prefix bbl) service repair manual (bbl0000...fusjfjsekemwer
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
Caterpillar cat 320 c ln excavator (prefix bbl) service repair manual (bbl000...fusjfjsekemwer
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
This document provides instructions for disassembling and assembling the piston pump of a 216B3 Skid Steer Loader. It lists 71 steps to fully disassemble the pump by removing components like fittings, springs, seals, bearings, pins and plates. The assembly section lists 8 steps such as installing liners, seals, bearings and shafts. Tools required are also listed.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
This document provides instructions for disassembling and assembling the piston motor of a 216B3 Skid Steer Loader. The disassembly process involves removing 25 parts from the motor in a specific order, taking care when removing springs. The assembly process reverses the disassembly steps, heating some parts before installing and using tools to install retaining rings and shafts.
This document provides assembly instructions for a piston pump in a 216B3 skid steer loader. It outlines 78 steps to assemble components like bearings, seals, pins, springs and plates. Special tools are required and parts must be installed in the correct orientation. Measurements taken during disassembly must be matched. The process involves pressing, torquing and installing retaining rings and seals. Finally, the assembled piston pump is installed back into the skid steer loader.
This document provides removal and installation instructions for a turbocharger and exhaust manifold on a 216B2 Skid Steer Loader with a 3024C engine. The turbocharger removal procedure involves removing hoses, bolts, tubes and gaskets. The exhaust manifold removal involves loosening nuts and bolts, removing the manifold and gasket, and possibly studs. Cleaning and inspection steps are outlined. Reinstallation involves cleaning, installing new gaskets, bolts and nuts in the specified order and torque. Valve spring removal and installation procedures are also summarized requiring the use of special tools.
Caterpillar cat 216 b skid steer loader (prefix rll) service repair manual (r...fusjfjsekemwer
This document provides instructions for installing the engine oil pump on a 216B skid steer loader. It describes:
1) Using an alignment tool to install the idler hub into the cylinder block.
2) Lubricating and installing various pump components like the inner rotor and idler gear.
3) Installing retaining rings and checking end play with a feeler gauge.
4) Reinstalling components like the oil strainer if removed previously.
This document provides instructions for removing and installing various components on a Caterpillar 216 Skid Steer Loader, including:
- Removing and installing the gas spring that supports the cab. Precautions are listed to safely release the spring force.
- Removing the fuel transfer pump, including disconnecting fuel lines and removing mounting bolts.
- Removing the fuel injection lines by disconnecting unions at the nozzles and pump, removing banjo bolts, washers and nuts. Identification marks should be made for reinstallation.
Case ih stx 430 tractor service repair manualfusjfjsekemwer
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists the tractor models covered, notes that engine repair information is in separate manuals, and outlines the sections and subsections contained in the service manual books, including specifications, lubrication/maintenance, engine removal/installation, and air induction system for certain tractor models.
Case ih puma 240 cvt tier 4 b (final) tractor service repair manualfusjfjsekemwer
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 1021 g stage iv wheel loader service repair manualfusjfjsekemwer
This service manual document provides information on servicing wheel loaders, including engine service. It includes specifications for 1121G and 1021G wheel loader models with Tier 4B engines. The document covers removing and servicing the engine and crankcase, as well as fuel, air intake, cooling, lubrication and emissions systems. Safety procedures and instructions are provided throughout.
Case 921 g wheel loader xr eh, new cab tier4b wheel loader service repair manualfusjfjsekemwer
This document is a service manual for CNH Industrial wheel loaders models 821G and 921G. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. Safety precautions are provided to prevent injury when servicing the equipment.
New holland w170 d zbar tier4b wheel loader service repair manualfusjfjsekemwer
This document is a service manual for wheel loaders models W130D and W170D. It contains information on engine systems, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. The manual provides maintenance and repair instructions for technicians and is organized by system with section numbers for easy reference.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
7. 1001-3
Bur 6-80470 Issued 1-06 Printed in U.S.A.
TORQUE SPECIFICATIONS - DECIMAL HARDWARE
Use the torques in this chart when special torques
are not given. These torques apply to fasteners with
both UNC and UNF threads as received from
suppliers dry, or when lubricated with engine oil. Not
applicable if special graphities, Molydisulfide
greases, or other extreme pressure lubricants are
used.
Grade 5 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
1/4 inch 108 to 132 12 to 15
5/16 inch 204 to 252 23 to 28
3/8 inch 420 to 504 48 to 57
Size
Pound-
Feet
Newton
metres
7/16 inch 54 to 64 73 to 87
1/2 inch 80 to 96 109 to 130
9/16 inch 110 to 132 149 to 179
5/8 inch 150 to 180 203 to 244
3/4 inch 270 to 324 366 to 439
7/8 inch 400 to 480 542 to 651
1.0 inch 580 to 696 787 to 944
1-1/8 inch 800 to 880 1085 to 1193
1-1/4 inch 1120 to 1240 1519 to 1681
1-3/8 inch 1460 to 1680 1980 to 2278
1-1/2 inch 1940 to 2200 2631 to 2983
Grade 8 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
1/4 inch 144 to 180 16 to 20
5/16 inch 288 to 348 33 to 39
3/8 inch 540 to 648 61 to 73
Size
Pound-
Feet
Newton
metres
7/16 inch 70 to 84 95 to 114
1/2 inch 110 to 132 149 to 179
9/16 inch 160 to 192 217 to 260
5/8 inch 220 to 264 298 to 358
3/4 inch 380 to 456 515 to 618
7/8 inch 600 to 720 814 to 976
1.0 inch 900 to 1080 1220 to 1465
1-1/8 inch 1280 to 1440 1736 to 1953
1-1/4 inch 1820 to 2000 2468 to 2712
1-3/8 inch 2380 to 2720 3227 to 3688
1-1/2 inch 3160 to 3560 4285 to 4827
NOTE: Use thick nuts with Grade 8 bolts.
8. 1001-4
Bur 6-80470 Issued 1-06 Printed in U.S.A.
TORQUE SPECIFICATIONS - METRIC HARDWARE
Use the following torques when specifications are not
given.
These values apply to fasteners with coarse threads
as received from supplier, plated or unplated, or
when lubricated with engine oil. These values do not
apply if graphite or Molydisulfide grease or oil is
used.
Grade 12.9 Bolts, Nuts, and Studs
Usually the torque values specified for grade 10.9
fasteners can be used satisfactorily on grade 12.9
fasteners.
Grade 8.8 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
M4 24 to 36 3 to 4
M5 60 to 72 7 to 8
M6 96 to 108 11 to 12
M8 228 to 276 26 to 31
M10 456 to 540 52 to 61
Size
Pound-
Feet
Newton
metres
M12 66 to 79 90 to 107
M14 106 to 127 144 to 172
M16 160 to 200 217 to 271
M20 320 to 380 434 to 515
M24 500 to 600 675 to 815
M30 920 to 1100 1250 to 1500
M36 1600 to 1950 2175 to 2600
8.8
Grade 10.9 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
M4 36 to 48 4 to 5
M5 84 to 96 9 to 11
M6 132 to 156 15 to 18
M8 324 to 384 37 to 43
Size
Pound-
Feet
Newton
metres
M10 54 to 64 73 to 87
M12 93 to 112 125 to 150
M14 149 to 179 200 to 245
M16 230 to 280 310 to 380
M20 450 to 540 610 to 730
M24 780 to 940 1050 to 1275
M30 1470 to 1770 2000 to 2400
M36 2580 to 3090 3500 to 4200
10.9
12.9
9. 1001-5
Bur 6-80470 Issued 1-06 Printed in U.S.A.
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS
37 Degree Flare Fitting
Tube OD
Hose ID
Thread
Size
Pound-
Inches
Newton
metres
1/4 inch
6.4 mm
7/16-20 72 to 144 8 to 16
5/16 inch
7.9 mm
1/2-20 96 to 192 11 to 22
3/8 inch
9.5 mm
9/16-18 120 to 300 14 to 34
1/2 inch
12.7 mm
3/4-16 180 to 504 20 to 57
5/8 inch
15.9 mm
7/8-14 300 to 696 34 to 79
Tube OD
Hose ID
Thread
Size
Pound-
Feet
Newton
metres
3/4 inch
19.0 mm
1-1/16-12 40 to 80 54 to 108
7/8 inch
22.2 mm
1-3/16-12 60 to 100 81 to 135
1.0 inch
25.4 mm
1-5/16-12 75 to 117 102 to 158
1-1/4 inch
31.8 mm
1-5/8-12 125 to 165 169 to 223
1-1/2 inch
38.1 mm
1-7/8-12 210 to 250 285 to 338
Split Flange Mounting Bolts
Size
Pound-
Inches
Newton
metres
5/16-18 180 to 240 20 to 27
3/8-16 240 to 300 27 to 34
7/16-14 420 to 540 47 to 61
Size
Pound-
Feet
Newton
metres
1/2-13 55 to 65 74 to 88
5/8-11 140 to 150 190 to 203
Straight Threads with O-ring
Tube OD
Hose ID
Thread
Size
Pound-
Inches
Newton
metres
1/4 inch
6.4 mm
7/16-20 144 to 228 16 to 26
5/16 inch
7.9 mm
1/2-20 192 to 300 22 to 34
3/8 inch
9.5 mm
9/16-18 300 to 480 34 to 54
1/2 inch
12.7 mm
3/4-16 540 to 804 57 to 91
Tube OD
Hose ID
Thread
Size
Pound-
Feet
Newton
metres
5/8 inch
15.9 mm
7/8-14 58 to 92 79 to 124
3/4 inch
19.0 mm
1-1/16-12 80 to 128 108 to 174
7/8 inch
22.2 mm
1-3/16-12 100 to 160 136 to 216
1.0 inch
25.4 mm
1-5/16-12 117 to 187 159 to 253
1-1/4 inch
31.8 mm
1-5/8-12 165 to 264 224 to 357
1-1/2 inch
38.1 mm
1-7/8-12 250 to 400 339 to 542
11. 2000-3
Bur 5-3370 Issued 8-06 Printed in U.S.A.
ENGINE
Removal
STEP 1
BD03A040
Park machine on a level surface and lower bucket to
ground. Put articulation lock in LOCKED position.
STEP 2
Stop engine. Actuate brake pedal several times to
discharge brake accumulators. Put key switch in ON
position and move loader control lever back and forth
at least 30 times to release any pressure from
hydraulic circuit. Put key switch in OFF position.
STEP 3
Slowly loosen the filler cap for hydraulic reservoir to
release air pressure in hydraulic reservoir.
STEP 4
Put master disconnect switch in OFF position.
Disconnect batteries from the machine.
STEP 5
BD06H046
Disconnect the backup alarm.
STEP 6
BD06H047
Loosen clamps and remove air filter intake from air
filter.
STEP 7
BD06H048
Run a lifting strap through the back hinge on each
side of the hood, route the strap behind the exhaust
stack.
STEP 8
BD06H052
Route the strap in front of the exhaust stack, attach
lifting equipment to the strap, take up the slack.
12. 2000-4
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 9
BD06H050
Remove the top two bolts from the hood and grill
mounting bracket at the rear of the frame.
STEP 10
BD06H053
Loosen the lower two bolts in the bracket.
NOTE: The bracket is slotted and the bolts do not
need to be removed.
STEP 11
BD06H051
Remove the two front bolts, nuts, and washers
securing the front of the hood.
STEP 12
BD06H054
Carefully raise and remove hood from loader. Lower
hood onto suitable platform and disconnect lifting
equipment.
STEP 13
BD02N160
Put a 40 liter (10 gallon) container below radiator
drain. Remove radiator cap. Remove cap and drain
coolant into container. Install cap after coolant has
drained. Install radiator cap.
STEP 14
BD02N160
Put a 20 liter (5 U.S. gallon) container below engine
oil drain. Remove cap and drain oil into container.
Install cap after oil has drained.
NOTE: After draining oil disconnect drain hose from
frame for removal with engine.
13. 2000-5
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 15
BD06H055
Loosen clamp on air cleaner intake hose and remove
the crankcase ventilation hose.
STEP 16
BD06H056
Loosen clamps on turbocharger and air cleaner,
remove the intake hose.
STEP 17
BD06H057
Tag and disconnect engine wiring harness connector
from air filter restriction switch.
STEP 18
BD06H060
Disconnect the engine coolant vent hose and root to
the rear of the engine.
STEP 19
BD06H058
Loosen the clamp on the turbocharger for the after
cooler inlet hose.
STEP 20
BD06H059
Loosen the clamp on the after cooler and remove the
after cooler inlet hose from the machine.
14. 2000-6
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 21
BD06F111
Loosen the clamp on the intake manifold for the after
cooler output hose.
STEP 22
BD06H176
Loosen the clamp on the after cooler and remove the
after cooler outlet hose from the machine.
STEP 23
BD06F113
BD06F114
Remove the four mounting bolts from the belt cover,
remove the cover.
NOTE: After removing the belt cover remove the
cover mounting brackets from the machine frame.
STEP 24
BD06F115
Remove the drive belt from the engine.
15. 2000-7
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 25
BD06F116
Loosen clamps and remove lower cooler hose from
the engine.
STEP 26
BD06F117
If loader is equipped with air conditioning, identify,
tag, and disconnect the engine wiring harness
connectors from air compressor clutch connector (1).
Remove the three mounting bolts (2) for the
compressor and set the compressor on the left
battery cover.
STEP 27
BD06F118
Tag and disconnect the wiring from the alternator.
STEP 28
BD06F119
Remove bolt securing wiring harness clamp to
engine.
STEP 29
BD06F120
Remove bolt securing wiring harness clamp (1) to the
engine. Remove ground wires (2) from the engine.
STEP 30
BD06F121
Tag and remove the wires from the starter solenoid
(3), remove the ground cable (2), and ground strap
(1) from the starter.
NOTE: Move the starter cables away from the
engine, move the wiring harness away from the
engine.
1
2
1
2
3
1
2
16. 2000-8
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 31
BD06F122
Remove the radiator hose (1) from the rear of the
engine, remove the heater hose from the rear of the
engine (2), remove the clamp bolts and clamps (3)
from the bell housing.
STEP 32
BD06H061
Tag and remove the grid heater cable.
STEP 33
BD06H062
Disconnect the wiring harness from the EDC 7
controller.
NOTE: Lifting up on the lever will release the
connector from the controller.
STEP 34
BD06F123
Remove the fuel line from the top of the EDC 7
controller, plug the line and cap the fitting.
STEP 35
BD06H065
Tag and disconnect the fuel filter heater wires (1),
disconnect the fuel line (2) from the fuel filter head,
plug the line and cap the fitting.
STEP 36
BD06F125
Remove bolt and clamp and move the fuel return line
away from the engine.
2
1
3
1
2
17. 2000-9
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 37
BD06F126
Connect and turn on vacuum pump to hydraulic
reservoir. Tag and remove the hydraulic lines from
the brake system pump, plug the lines and cap the
fittings.
STEP 38
BD06F127
Remove the lower cover for the drive shaft.
STEP 39
BD03A172
Remove the drive shaft bolts from the flywheel. Move
the drive shaft clear of the flywheel.
STEP 40
Connect suitable lifting equipment to engine lifting
brackets. Take up all slack in lifting equipment.
Remove the engine mounting bolts and lift the engine
enough to gain access to the drain hose, pull the
drain hose with the engine.
STEP 41
Slowly raise engine from rear chassis. Be sure all
harness connections and hoses have been
disconnected and are clear of the engine. Remove
engine from machine.
18. 2000-10
Bur 5-3370 Issued 8-06 Printed in U.S.A.
Installation
BS03B035
STEP 42
If engine rubber isolators require replacement,
remove and discard isolators (3 and 4). Install new
rubber isolator (4), then rubber isolator (3).
STEP 43
If mounting brackets were removed from the engine,
retorque the mounts to the engine to 118 to 133 Nm
(87 to 98 pound-feet).
STEP 44
Slowly raise engine and move into position over rear
chassis. Be sure all harness connections and hoses
are out of the way then lower engine. Put washer (5)
between front rubber isolator (4) and chassis. Install
washer (2), bolt (1), washer (6), and nut (7) in engine
isolators. Lower engine into position.
STEP 45
Tighten engine mounting bolts to a torque of 244 to
298 Nm (180 to 220 pound-feet).
STEP 46
Disconnect lifting equipment from engine lifting
brackets.
STEP 47
Connect engine oil drain hose to frame bracket.
STEP 48
BD03A172
At front of engine, position drive shaft on engine
coupling. Install six bolts to secure drive shaft to
engine coupling. Tighten the six bolts to a torque of
53 to 62 Nm (39 to 46 pound-feet).
1. ENGINE MOUNT BOLT 3. INSOLATOR UPPER 5. WASHER 7. NUT
2. WASHER 4. INSOLATOR LOWER 6. WASHER 8. REMOTE OIL DRAIN HOSE
1
4
3
2
7
6
5
4
3
2
1
1
7
8
7
6
5
2
3
4
5
6
19. 2000-11
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 49
BD06F127
Install the lower cover for the drive shaft.
STEP 50
BD06F126
Connect and turn on vacuum pump to the hydraulic
reservoir. Remove caps from fittings and plugs from
hoses. Connect hoses to brake pump following tags
installed during removal. Remove and discard tags.
Turn off and disconnect vacuum pump from hydraulic
reservoir.
STEP 51
BD06F125
Install bolt and clamp for fuel return hose.
STEP 52
BD06H065
Remove cap from fitting and plug from the hose,
connect fuel line (2). Connect fuel filter heater wires
(1). Remove and discard tag.
STEP 53
BD06F123
Remove cap from fitting and plug from the hose,
connect fuel line to EDC 7.
STEP 54
BD06H062
Connect wiring harness to EDC 7 controller.
NOTE: Start the connector on the EDC 7 with lever
straight out from EDC 7. Use lever to pull connector
into position.
1
2
20. 2000-12
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 55
BD06H061
Connect grid heater cable to grid heater. Remove
and discard tag.
STEP 56
BD06F122
Install the heater hose (2) to the rear of the engine,
mount the clamps (3), install the radiator hose (1).
STEP 57
BD06H060
Connect the engine coolant vent hose.
STEP 58
BD06F121
Install the wires to the starter solenoid (3), install the
ground cable (2), and ground strap (1) to the starter.
Remove and discard tags.
STEP 59
BD06F120
Install bolt securing wiring harness (1) clamp to the
engine. Install ground wires (2) to the engine.
STEP 60
BD06F119
Install bolt securing wiring harness clamp to engine.
2
1
3
3
1
2
1
2
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. 2000-13
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 61
BD06F118
Connect the wiring to the alternator. Remove and
discard tags.
STEP 62
BD06F117
If loader is equipped with air conditioning, mount the
compressor using the three mounting bolts (2),
connect the engine wiring harness connectors to air
compressor clutch connector (1). Remove and
discard tags.
STEP 63
BD06F116
Install lower cooler hose to the engine and tighten the
clamps to a torque of 10.1 to 11.3 Nm (90 to 100
lb-inch).
STEP 64
BD06F115
Install the drive belt.
STEP 65
BD06F113
BD06F114
Install the cover mounting brackets to the machine
frame. Install the belt cover, install the four mounting
bolts for the belt cover.
1
2
23. 2000-14
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 66
BD06H176
Place the after cooler outlet hose on the machine.
Tighten the clamp on the after cooler.
STEP 67
BD06F111
Tighten the clamp on the intake manifold for the after
cooler output hose.
STEP 68
BD06H059
Place the after cooler inlet hose on the machine.
Tighten the clamp on the after cooler.
STEP 69
BD06H057
Connect engine wiring harness connector to air filter
restriction switch. Remove and discard tag.
STEP 70
BD06H058
Tighten the clamp on the turbocharger for the after
cooler inlet hose.
STEP 71
BD06H056
Install the intake hose and tighten the clamps on
turbocharger and air cleaner.
24. 2000-15
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 72
BD06H055
Install the crankcase ventilation hose and tighten the
clamp on air cleaner intake hose.
STEP 73
BD06H054
Carefully raise and position the hood onto loader,
lower the hood and grill brackets onto the two lower
bolts at the rear of the frame.
STEP 74
BD06H051
Install the two front bolts and washers securing the
front of the hood.
STEP 75
BD06H049
Use two new self locking nuts on the front bolts,
tighten and secure the hood.
STEP 76
BD06H050
Install two top bolts and washers, one on each side
of the machine, securing the hood to the rear frame,
tighten all four bolts.
STEP 77
BD02N160
Check and make sure that drain caps are tight.
STEP 78
Install a new oil filter on engine. Fill engine with oil,
see section 1002 for specifications.
25. 2000-16
Bur 5-3370 Issued 8-06 Printed in U.S.A.
STEP 79
If hydraulic reservoir was drained, fill reservoir with
oil, see section 1002 for specifications.
STEP 80
Fill engine coolant system with a solution of 50%
Ethylene Glycol and 50% water. Fill cooling system,
see section 1002 for specifications. Install the
radiator cap. Fill the coolant reservoir up to the FULL
mark on the reservoir.
STEP 81
Connect the batteries, install battery covers, put
master disconnect switch in ON position.
STEP 82
Start engine and run the engine at low idle. Run the
engine at operating temperature for approximately
five minutes to completely mix the Ethylene Glycol
and water. When the coolant is at operating
temperature, stop the engine. When engine has
cooled, check the coolant level at the reservoir.
WARNING: Hot coolant can spray out if radiator cap
is removed. To remove radiator cap: Let system cool,
turn to first notch, then wait until all pressure is
released. Scalding can result from fast removal of
radiator cap.
STEP 83
Put articulation lock in OPERATING position.
26. 2000-17
Bur 5-3370 Issued 8-06 Printed in U.S.A.
RADIATOR
Removal
STEP 84
Park loader on level surface and lower bucket to
ground. Apply parking brake and shut down engine.
STEP 85
BD00M030
Put articulation lock in LOCKED position.
STEP 86
Open and raise hood.
STEP 87
Put master disconnect switch in OFF position.
STEP 88
Remove bolt and washer securing LH fender.
Remove LH fender.
STEP 89
BD00M031
Put a 37.8 liter (10 gallon) container below radiator
drain. Remove cap and drain coolant into container.
Install cap after coolant has drained.
STEP 90
BD01D188
At top of cooling system frame, loosen two hose
clamps (1). Remove hose (2).
STEP 91
BD01D229
Loosen two clamps securing radiator bottom hose.
Remove bottom hose.
STEP 92
BD01D223
Remove radiator cap (1) and disconnect overflow
hose (2) from radiator. Install radiator cap. Remove
screw (3) and install lifting eye.
1. HOSE CLAMP 2. HOSE
1. RADIATOR CAP 3. SCREW
2. OVERFLOW HOSE
1
1
2
3
1 2