Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjjsekkdmme
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to take off the cover base. The installation procedure specifies tightening bolts and reconnecting harnesses in the reverse order. Precautions are given to keep parts clean and prevent damage from contaminants.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjjsekkdmme
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal instructions describe removing gears, covers, and other components. The water pump instructions describe removing the pump, pulley, and O-ring seal, as well as disassembling, inspecting, and reassembling the pump components. Precautions are provided regarding cleaning parts and containing fluids.
Caterpillar cat 318 c excavator (prefix faa) service repair manual (faa00001 ...fjjsekkdmme
This document provides instructions for installing pistons and connecting rods, removing and installing connecting rod bearings, and removing crankshaft main bearings for Caterpillar 3064 and 3066 engines. The procedures describe cleaning and lubricating parts, aligning identification marks, using specific tools, and torquing fasteners to the proper specifications.
Caterpillar cat 318 c excavator (prefix btg) service repair manual (btg00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. The disassembly procedure involves using various tools to remove 31 parts from the final drive including the cover, planetary assembly, retaining rings, gears, bearings, seals and housing components. The assembly procedure instructs installing these 31 parts in reverse order and provides details on cleaning, lubricating and setting torque specifications.
Caterpillar cat 316 f l excavator (prefix ydl) service repair manual (ydl0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjjsekkdmme
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to take off the cover base. The installation procedure specifies tightening bolts and reconnecting harnesses in the reverse order. Precautions are given to keep parts clean and prevent damage from contaminants.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjjsekkdmme
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal instructions describe removing gears, covers, and other components. The water pump instructions describe removing the pump, pulley, and O-ring seal, as well as disassembling, inspecting, and reassembling the pump components. Precautions are provided regarding cleaning parts and containing fluids.
Caterpillar cat 318 c excavator (prefix faa) service repair manual (faa00001 ...fjjsekkdmme
This document provides instructions for installing pistons and connecting rods, removing and installing connecting rod bearings, and removing crankshaft main bearings for Caterpillar 3064 and 3066 engines. The procedures describe cleaning and lubricating parts, aligning identification marks, using specific tools, and torquing fasteners to the proper specifications.
Caterpillar cat 318 c excavator (prefix btg) service repair manual (btg00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. The disassembly procedure involves using various tools to remove 31 parts from the final drive including the cover, planetary assembly, retaining rings, gears, bearings, seals and housing components. The assembly procedure instructs installing these 31 parts in reverse order and provides details on cleaning, lubricating and setting torque specifications.
Caterpillar cat 316 f l excavator (prefix ydl) service repair manual (ydl0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjjsekkdmme
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout the process.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c l excavator (prefix cfb) service repair manual (cfb0000...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing.
3) Assembly requires determining the proper shim thickness to set the rolling torque and installing components in reverse order of disassembly. Cleanliness and applying oil to components is emphasized.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and the head is positioned using guide bolts before reinstalling the bolts and tightening them in stages.
Caterpillar cat 315 c l excavator (prefix ake) service repair manual (ake0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both disassembly and assembly.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 25 steps for reassembly, instructing technicians to clean parts, replace seals, apply lubricants, and reinstall components in reverse order using various tools. Technicians are advised to mark parts for orientation and take precautions when working with pressurized or spring-loaded components.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c excavator (prefix cfb) service repair manual (cfb00001 ...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the final drive.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is positioned and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools like guide bolts and a torque wrench are required to correctly perform the work.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both preventing damage and ensuring smooth operation.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjjsekkdmme
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top-dead-center. Proper installation of new valve springs and related components is also outlined. Safety notices are included to prevent injury from parts propelled by spring forces.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjjsekkdmme
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut to turn the crank, and removing main bearing caps.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 215 d excavator (prefix 9tf) service repair manual (9tf00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B engine. The disassembly process involves removing various parts like the fuel rack, lifters, camshaft and bearings. The assembly process details installing these parts in reverse order and setting proper clearances. Tools needed include retaining ring pliers and a driver group. Precautions like keeping parts clean and applying oil before assembly are also specified.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v023...fjjsekkdmme
The document provides instructions for removing and installing the flywheel housing on a 130G motor grader with a 3304 engine. It describes using link brackets and a hoist to remove the housing, which weighs 37 kg. Installation involves placing a gasket and bolting the housing back onto the engine, then reinstalling components like the oil drain line and crankshaft rear seal.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjjsekkdmme
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout the process.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c l excavator (prefix cfb) service repair manual (cfb0000...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing.
3) Assembly requires determining the proper shim thickness to set the rolling torque and installing components in reverse order of disassembly. Cleanliness and applying oil to components is emphasized.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and the head is positioned using guide bolts before reinstalling the bolts and tightening them in stages.
Caterpillar cat 315 c l excavator (prefix ake) service repair manual (ake0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both disassembly and assembly.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 25 steps for reassembly, instructing technicians to clean parts, replace seals, apply lubricants, and reinstall components in reverse order using various tools. Technicians are advised to mark parts for orientation and take precautions when working with pressurized or spring-loaded components.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c excavator (prefix cfb) service repair manual (cfb00001 ...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the final drive.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is positioned and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools like guide bolts and a torque wrench are required to correctly perform the work.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both preventing damage and ensuring smooth operation.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjjsekkdmme
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top-dead-center. Proper installation of new valve springs and related components is also outlined. Safety notices are included to prevent injury from parts propelled by spring forces.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjjsekkdmme
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut to turn the crank, and removing main bearing caps.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 215 d excavator (prefix 9tf) service repair manual (9tf00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B engine. The disassembly process involves removing various parts like the fuel rack, lifters, camshaft and bearings. The assembly process details installing these parts in reverse order and setting proper clearances. Tools needed include retaining ring pliers and a driver group. Precautions like keeping parts clean and applying oil before assembly are also specified.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v023...fjjsekkdmme
The document provides instructions for removing and installing the flywheel housing on a 130G motor grader with a 3304 engine. It describes using link brackets and a hoist to remove the housing, which weighs 37 kg. Installation involves placing a gasket and bolting the housing back onto the engine, then reinstalling components like the oil drain line and crankshaft rear seal.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
9. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your NEW HOLLAND Sales and Service Networks.
48193205 12/10/2017
3
10. INTRODUCTION
Safety rules - Personal safety
General safety rules
Use caution when operating the machine on slopes. Raised equipment, full tanks and other loads will change the
center of gravity of the machine. The machine can tip or roll over when near ditches and embankments or uneven
surfaces.
Stay off slopes too steep for safe operation. Shift down before you start up or down a hill with a heavy load. Avoid
“free wheeling.”
Never permit anyone other than the operator to ride on the machine.
Never operate the machine under the influence of alcohol, drugs, or while otherwise impaired.
While driving on the road, the seat swivel position must always be straight forward and locked in position with no
rotation. The seat swivel should only be rotated for in field operation.
Do not drive on roads, or at high speed anywhere, with the differential lock engaged. Difficult steering will occur, and
can result in an accident. In field operation, use the differential lock for traction improvement, but release for turning
at row ends.
Do not exceed implement transport speed or the speed rating on the implement tires. Review the implements Oper-
ator’s Manual for specifications. Failure to comply could result in death or serious injury.
For speeds up to 16 km/h (10 mph), make sure that the weight of a trailed vehicle that is not equipped with brakes
does NOT EXCEED 1.5 times the Tractor weight. For speeds up to 40 km/h (25 mph), make sure that the weight of
the trailed vehicle that is not equipped with brakes, does NOT EXCEED the weight of the Tractor. Stopping distance
increases with increasing speed as the weight of the towed load increases, especially on hills and slopes.
Rear upset can result if pulling from wrong location on tractor. Hitch only to the drawbar. Use three-point hitch only
with the implements designed for its use – not as a drawbar.
Modifications made to this machine may increase the likelihood or potential for debris accumulations that would nor-
mally not be present. Modifications include frame-mounted attachments, plates, screens, or other aftermarket equip-
ment. Operators of modified machines must be aware of accumulations of organic debris and/or material and overall
machine cleanliness.
Modified machines require additional and more frequent inspection and cleaning during usage. The machine may
require inspection and cleaning multiple times per day during usage. Operators must be aware of the operating
environment and conditions. Operators must take appropriate actions to maintain the machines during use. In
particular, pay attention to the following machine areas:
• In and around the engine compartment
• Hot exhaust components
• Moving, turning, or rotating machine components
Operators that operate the machine in atypical applications and/or conditions must be aware of accumulations of
organic debris and/or material and overall machine cleanliness. Pay particular attention where material accumulations
are possible or may result.
Machines that operate in atypical applications or conditions require additional and more frequent inspection and
cleaning during usage. The machine may require inspection and cleaning multiple times per day during usage.
Operators must be aware of the operating environment and conditions. Operators must take appropriate actions to
maintain the machines during use. In particular, pay attention to the following machine areas:
• In and around the engine compartment
• Hot exhaust components
• Moving, turning, or rotating machine components
Do not look directly into the front or rear work lamps. Eye damage can occur.
48193205 12/10/2017
4
11. INTRODUCTION
Do not tamper with the ballast on the front or rear High Intensity Discharge (HID) lamp since it uses high voltage.
Personal injury or death can occur.
To avoid possible eye damage from microwave signals emitted by the radar sensor, do not look directly into the sensor
face.
When digging or using ground engaging attachments be aware of buried cables. Contact local utilities to determine
the locations of services.
Pay attention to overhead power lines and hanging obstacles. High voltage lines may require significant clearance
for safety.
Hydraulic oil or diesel fuel leaking under pressure can penetrate the skin, causing serious injury or infection.
• DO NOT use your hand to check for leaks. Use a piece of cardboard or paper.
• Stop engine, remove key and relieve the pressure before connecting or disconnecting fluid lines.
• Make sure all components are in good condition and tighten all connections before starting the engine or pressur-
izing the system.
• If hydraulic fluid or diesel fuel penetrates the skin, seek medical attention immediately.
• Continuous long term contact with hydraulic fluid may cause skin cancer. Avoid long term contact and wash the
skin promptly with soap and water.
Keep clear of moving parts. Loose clothing, jewelry, watches, long hair, and other loose or hanging items can become
entangled in moving parts.
Wear protective equipment when appropriate.
DO NOT attempt to remove material from any part of the machine while it is being operated or components are in
motion.
Make sure all guards and shields are in good condition and properly installed before operating the machine. Never
operate the machine with shields removed. Always close access doors or panels before operating the machine.
Dirty or slippery steps, ladders, walkways, and platforms can cause falls. Make sure these surfaces remain clean and
clear of debris.
A person or pet within the operating area of a machine can be struck or crushed by the machine or its equipment. DO
NOT allow anyone to enter the work area.
Raised equipment and/or loads can fall unexpectedly and crush persons underneath. Never allow anyone to enter
the area underneath raised equipment during operation.
Never operate engine in enclosed spaces as harmful exhaust gases may build up.
Before starting the machine, be sure that all controls are in neutral or park lock position.
Start the engine only from the operator’s seat. If the safety start switch is bypassed, the engine can start with the
transmission in gear. Do not connect or short across terminals on the starter solenoid. Attach jumper cables as
described in the manual. Starting in gear may cause death or serious injury.
Always keep windows, mirrors, all lighting, and Slow Moving Vehicle (SMV) emblem clean to provide the best possible
visibility while operating the machine.
Operate controls only when seated in the operator’s seat, except for those controls expressly intended for use from
other locations.
Before leaving the machine:
1. Park machine on a firm level surface.
2. Put all controls in neutral or park lock position.
3. Engage park brake. Use wheel chocks if required.
4. Lower all hydraulic equipment — Implements, header, etc.
48193205 12/10/2017
5
12. INTRODUCTION
5. Turn off engine and remove key.
When, due to exceptional circumstances, you would decide to keep the engine running after leaving the operator’s
station, then the following precautions must be followed:
1. Bring the engine to low idle speed.
2. Disengage all drive systems.
3. WARNING
Some components may continue to run down after you disengage drive systems.
Make sure all drive systems are fully disengaged.
Failure to comply could result in death or serious injury.
W0113A
Shift the transmission into park.
4. Apply the parking brake.
48193205 12/10/2017
6
14. Engine - Fuel tanks
Fuel cooler - Remove - Row crop frame units
T9.435 NA
T9.480 NA
T9.530 NA
T9.565 NA
1. Open the hood.
2. Remove the two clip pins and open the front cooler
frame.
RAIL13TR03049AA 1
3. Protect the oil coolers and air conditioning condenser.
RAIL13TR03057AA 2
4. Remove the top two bolts securing the fuel cooler to
the cooling package.
RAIL13TR03050AA 3
48193205 12/10/2017
10.2 [10.216] / 3
15. Engine - Fuel tanks
5. Install two guide studs (1).
6. Remove the two bottom bolts (2).
RAIL13TR03058AA 4
7. Set the cooler aside.
8. Disconnect the fuel hoses (1) from the cooler.
NOTE: Plug and cap all disconnected hoses and fittings.
9. Remove the four nuts and bolts (2) that secure the
cooler to the support brackets.
RAIL13TR03053AA 5
48193205 12/10/2017
10.2 [10.216] / 4
16. Engine - Fuel tanks
Fuel cooler - Install - Row crop frame units
T9.435 NA
T9.480 NA
T9.530 NA
T9.565 NA
1. Assemble the four nuts and bolts (1) that secure the
cooler to the support brackets.
2. Connect the fuel hoses (2) to the cooler.
NOTE: Remove the plugs and caps from the disconnected
hoses and fittings.
RAIL13TR03053AA 1
3. Install two guide studs (1) and set the fuel cooler in
place on the cooling package.
4. Assemble the two bottom bolts (2) securing the fuel
cooler to the cooling package.
RAIL13TR03058AA 2
5. Remove the guide pins and assemble the top two bolts.
RAIL13TR03050AA 3
48193205 12/10/2017
10.2 [10.216] / 5
17. Engine - Fuel tanks
6. Remove the material that was put in place to protect
the oil coolers and air conditioning condenser.
RAIL13TR03057AA 4
7. Close the front cooler frame and install the two clip pins.
RAIL13TR03049AA 5
8. Start the engine and check for leaks.
9. Close the hood.
48193205 12/10/2017
10.2 [10.216] / 6
18. Engine - Fuel tanks
Fuel cooler - Remove - High power frame units
T9.600 NA
T9.645 NA
T9.700 NA
1. Disconnect the fuel hoses from the cooler.
NOTE: Plug and cap disconnected hoses and fittings.
RAIL14TR00421AA 1
2. Remove the mounting bolts and remove the fuel cooler
from the cooling package frame.
RAIL13TR00662AA 2
48193205 12/10/2017
10.2 [10.216] / 7
19. Engine - Fuel tanks
Fuel cooler - Install - High power frame units
T9.600 NA
T9.645 NA
T9.700 NA
1. Lift the fuel cooler in place and secure with the mount-
ing bolts.
RAIL13TR00662AA 1
2. Connect the fuel hoses to the cooler.
RAIL14TR00421AA 2
3. Run the engine and check for leaks.
48193205 12/10/2017
10.2 [10.216] / 8
20. Engine - Air cleaners and lines
Air cleaner - Remove - High power frame models
T9.600 NA
T9.645 NA
T9.700 NA
1. Shut off engine and remove key.
Open hood hatch.
RCPH10FWD247BBC 1
2. Release clamps and remove cover.
RCPH10FWD836BAM 2
3. Pull back, then up and remove primary filter.
RCPH10FWD838BAM 3
48193205 12/10/2017
10.3 [10.202] / 3
21. Engine - Air cleaners and lines
4. Pull back and remove secondary filter.
RCPH10FWD840BAM 4
5. Clean inside of housing.
RCPH10FWD843BAM 5
6. Repeat 2 through 5 for right hand side filter.
48193205 12/10/2017
10.3 [10.202] / 4
22. Engine - Air cleaners and lines
Air cleaner - Install - High power frame models
T9.600 NA
T9.645 NA
T9.700 NA
1. Install secondary filter.
RCPH10FWD841BAM 1
2. Install primary filter. Set in and all way forward.
RCPH10FWD839BAM 2
3. Install cover and secure with clips.
RCPH10FWD836BAM 3
48193205 12/10/2017
10.3 [10.202] / 5
23. Engine - Air cleaners and lines
4. Close hood hatch.
RCPH10FWD247BBC 4
48193205 12/10/2017
10.3 [10.202] / 6
24. Engine - Air cleaners and lines
Air cleaner - Remove - Row crop frame models
T9.435 NA
T9.480 NA
T9.530 NA
T9.565 NA
1. Shut off engine, remove key and open hood hatch.
RCPH10FWD840AAC 1
2. Release the four air cleaner housing cover latches and
remove cover.
RCPH10FWD925BAC 2
3. Pull primary filter from air cleaner housing.
RCPH10FWD926BAC 3
48193205 12/10/2017
10.3 [10.202] / 7
25. Engine - Air cleaners and lines
4. Pull the secondary filter from air cleaner housing.
RCPH10FWD927BAC 4
5. Clean inside of air cleaner housing.
RCPH10FWD928BAC 5
48193205 12/10/2017
10.3 [10.202] / 8
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Engine - Air cleaners and lines
Air cleaner - Install - Row crop frame models
T9.435 NA
T9.480 NA
T9.530 NA
T9.565 NA
1. Install secondary filter into air cleaner housing.
RCPH10FWD927BAC 1
2. Install primary filter into air cleaner housing.
RCPH10FWD926BAC 2
3. Install cover and secure the four latches.
RCPH10FWD925BAC 3
48193205 12/10/2017
10.3 [10.202] / 9
28. Engine - Air cleaners and lines
4. Close hood hatch.
RCPH10FWD840AAC 4
48193205 12/10/2017
10.3 [10.202] / 10