This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top-dead-center. Proper installation of new valve springs and related components is also outlined. Safety notices are included to prevent injury from parts propelled by spring forces.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top dead center. Proper cleaning and inspection of parts is emphasized. The installation procedure describes compressing the springs, installing new seals, and ensuring correct valve depths are achieved. Safety notices warn of potential injury from compressed springs and ensure springs are replaced in pairs for each cylinder.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 246 c skid steer loader (prefix jay) service repair manual (j...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 246C Skid Steer Loader with a 3044C engine. The removal procedure involves using special tools to compress the valve springs so the retainers and springs can be removed safely. Installation involves inspecting the springs and using the compressor tool to insert the springs and retainers. Proper safety precautions are outlined to avoid injury from the spring force. The process is also described for removing valves from a cylinder head removed from the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C4.2 engine. It describes the required tools and gives step-by-step procedures for removing valve springs safely while ensuring the piston is at top dead center. Proper cleaning and inspection of parts is emphasized. The installation procedure describes compressing the springs, installing new seals, and ensuring correct valve depths are achieved. Safety notices warn of potential injury from compressed springs and ensure springs are replaced in pairs for each cylinder.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 246 c skid steer loader (prefix jay) service repair manual (j...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 246C Skid Steer Loader with a 3044C engine. The removal procedure involves using special tools to compress the valve springs so the retainers and springs can be removed safely. Installation involves inspecting the springs and using the compressor tool to insert the springs and retainers. Proper safety precautions are outlined to avoid injury from the spring force. The process is also described for removing valves from a cylinder head removed from the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The removal procedure involves using tooling to compress the valve springs so the valves can be worked on safely. New valve stem seals must be installed before reinstalling the valve springs. The installation procedure specifies cleaning and inspecting components before reassembly in the correct orientation. Safety notices are provided to wear protective equipment when working with compressed springs.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The key steps are:
1. Use special tools to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Remove the valve keepers and spring retainer to access the valve spring.
3. Installation is the reverse of removal, ensuring parts are clean and lubricated before reassembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor tools to compress the valve spring and remove/install valve keepers and springs while ensuring the piston is at top dead center.
2. Clean and inspect all cylinder head components before installation and replace any worn or damaged parts.
3. Lubricate valve stems before installing valves, springs, retainers and seals in the proper order and orientation using tools as needed.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor and crankshaft turning tools to compress the valve spring and rotate the piston to access the valve spring.
2. Remove the valve keepers and spring retainer to take off the valve spring.
3. To install, lubricate the valve stem and place the spring and retainer on the cylinder head. Use the compressor to apply pressure and install the keepers.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. Key steps include:
1. Ensuring the piston is at top dead center to prevent the valve from dropping into the cylinder bore. Compressing the valve spring using a tool and rotating the crankshaft.
2. Removing the valve keepers and spring retainer to access the valve spring. Slowly releasing pressure to remove the spring.
3. Cleaning and lubricating components before installation. Compressing the new spring using a tool and installing the keepers and retainer.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The summary is:
1. The procedure describes using special tools to compress the valve springs so that the valves, spring retainers, and valve keepers can be safely removed and installed.
2. The process involves rotating the crankshaft to position the piston at top dead center before removing each valve spring to prevent the valve from falling into the cylinder.
3. Reinstallation requires cleaning and inspecting components, lubricating the valves, and using tools to carefully compress the springs squarely during assembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjjsekkdmme
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to take off the cover base. The installation procedure specifies tightening bolts and reconnecting harnesses in the reverse order. Precautions are given to keep parts clean and prevent damage from contaminants.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjjsekkdmme
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal instructions describe removing gears, covers, and other components. The water pump instructions describe removing the pump, pulley, and O-ring seal, as well as disassembling, inspecting, and reassembling the pump components. Precautions are provided regarding cleaning parts and containing fluids.
Caterpillar cat 318 c excavator (prefix faa) service repair manual (faa00001 ...fjjsekkdmme
This document provides instructions for installing pistons and connecting rods, removing and installing connecting rod bearings, and removing crankshaft main bearings for Caterpillar 3064 and 3066 engines. The procedures describe cleaning and lubricating parts, aligning identification marks, using specific tools, and torquing fasteners to the proper specifications.
Caterpillar cat 318 c excavator (prefix btg) service repair manual (btg00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. The disassembly procedure involves using various tools to remove 31 parts from the final drive including the cover, planetary assembly, retaining rings, gears, bearings, seals and housing components. The assembly procedure instructs installing these 31 parts in reverse order and provides details on cleaning, lubricating and setting torque specifications.
Caterpillar cat 316 f l excavator (prefix ydl) service repair manual (ydl0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjjsekkdmme
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
More Related Content
Similar to Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00001 and up)
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Safety precautions are outlined to prevent injury from parts under spring pressure.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. The removal procedure involves using tooling to compress the valve springs so the valves can be worked on safely. New valve stem seals must be installed before reinstalling the valve springs. The installation procedure specifies cleaning and inspecting components before reassembly in the correct orientation. Safety notices are provided to wear protective equipment when working with compressed springs.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The key steps are:
1. Use special tools to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Remove the valve keepers and spring retainer to access the valve spring.
3. Installation is the reverse of removal, ensuring parts are clean and lubricated before reassembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one piston at a time. Proper tool use and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor tools to compress the valve spring and remove/install valve keepers and springs while ensuring the piston is at top dead center.
2. Clean and inspect all cylinder head components before installation and replace any worn or damaged parts.
3. Lubricate valve stems before installing valves, springs, retainers and seals in the proper order and orientation using tools as needed.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fujsekfsmemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The key steps are:
1. Use valve spring compressor and crankshaft turning tools to compress the valve spring and rotate the piston to access the valve spring.
2. Remove the valve keepers and spring retainer to take off the valve spring.
3. To install, lubricate the valve stem and place the spring and retainer on the cylinder head. Use the compressor to apply pressure and install the keepers.
Caterpillar cat 320 d ln excavator (prefix gdp) service repair manual (gdp000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. Key steps include:
1. Ensuring the piston is at top dead center to prevent the valve from dropping into the cylinder bore. Compressing the valve spring using a tool and rotating the crankshaft.
2. Removing the valve keepers and spring retainer to access the valve spring. Slowly releasing pressure to remove the spring.
3. Cleaning and lubricating components before installation. Compressing the new spring using a tool and installing the keepers and retainer.
Caterpillar cat 320 d l excavator (prefix gdp) service repair manual (gdp0000...fjkskekdmmenm
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator. The summary is:
1. The procedure describes using special tools to compress the valve springs so that the valves, spring retainers, and valve keepers can be safely removed and installed.
2. The process involves rotating the crankshaft to position the piston at top dead center before removing each valve spring to prevent the valve from falling into the cylinder.
3. Reinstallation requires cleaning and inspecting components, lubricating the valves, and using tools to carefully compress the springs squarely during assembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...ddkkddm
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The procedure involves using specialty tools to compress the valve springs so that the valves, springs, and related components can be safely accessed and removed or installed one at a time. Proper cleaning and inspection of parts is emphasized to prevent premature wear. The work must be done with the pistons positioned correctly to avoid parts falling into the cylinders.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fikskkdmmd1
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from the force of the compressed springs.
Similar to Caterpillar cat 311 d lrr excavator (prefix lka) service repair manual (lka00001 and up) (12)
Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjjsekkdmme
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to take off the cover base. The installation procedure specifies tightening bolts and reconnecting harnesses in the reverse order. Precautions are given to keep parts clean and prevent damage from contaminants.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjjsekkdmme
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal instructions describe removing gears, covers, and other components. The water pump instructions describe removing the pump, pulley, and O-ring seal, as well as disassembling, inspecting, and reassembling the pump components. Precautions are provided regarding cleaning parts and containing fluids.
Caterpillar cat 318 c excavator (prefix faa) service repair manual (faa00001 ...fjjsekkdmme
This document provides instructions for installing pistons and connecting rods, removing and installing connecting rod bearings, and removing crankshaft main bearings for Caterpillar 3064 and 3066 engines. The procedures describe cleaning and lubricating parts, aligning identification marks, using specific tools, and torquing fasteners to the proper specifications.
Caterpillar cat 318 c excavator (prefix btg) service repair manual (btg00001 ...fjjsekkdmme
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. The disassembly procedure involves using various tools to remove 31 parts from the final drive including the cover, planetary assembly, retaining rings, gears, bearings, seals and housing components. The assembly procedure instructs installing these 31 parts in reverse order and provides details on cleaning, lubricating and setting torque specifications.
Caterpillar cat 316 f l excavator (prefix ydl) service repair manual (ydl0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 316 f l excavator (prefix ecz) service repair manual (ecz0000...fjjsekkdmme
This document provides service and repair instructions for the final drive and related components of a 316F L excavator. It includes specifications, illustrations, removal and disassembly procedures, and assembly instructions. The procedures involve using various tools to remove, disassemble, and replace components like gears, bearings, seals, and housings. Precautions are outlined for cleaning parts and applying lubricants and sealants during assembly.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjjsekkdmme
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
Caterpillar cat 315 c l excavator (prefix cjc) service repair manual (cjc0000...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. The 27 steps for assembly describe installing these same components in reverse order, making sure to clean parts, replace seals, and apply lubricants. Special tools and safety precautions are noted throughout the process.
Caterpillar cat 315 c l excavator (prefix cft) service repair manual (cft0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c l excavator (prefix cfb) service repair manual (cfb0000...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing.
3) Assembly requires determining the proper shim thickness to set the rolling torque and installing components in reverse order of disassembly. Cleanliness and applying oil to components is emphasized.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and the head is positioned using guide bolts before reinstalling the bolts and tightening them in stages.
Caterpillar cat 315 c l excavator (prefix ake) service repair manual (ake0000...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both disassembly and assembly.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...fjjsekkdmme
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 25 steps for reassembly, instructing technicians to clean parts, replace seals, apply lubricants, and reinstall components in reverse order using various tools. Technicians are advised to mark parts for orientation and take precautions when working with pressurized or spring-loaded components.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the travel motor by removing components like bolts, seals, bearings, pistons, and plates. It then describes 26 steps for reassembling the travel motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants, and take care when installing spring-loaded or sealed components.
Caterpillar cat 315 c excavator (prefix cfb) service repair manual (cfb00001 ...fjjsekkdmme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the final drive.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is positioned and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools like guide bolts and a torque wrench are required to correctly perform the work.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjjsekkdmme
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, which include removing bolts, seals, plates, pistons, springs and other components. It then lists 25 steps for assembly, which involve cleaning parts, applying lubricants, and reinstalling components in reverse order using various tools. Proper cleaning and lubrication of parts is emphasized for both preventing damage and ensuring smooth operation.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767700
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
B. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
1/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Illustration 1 g01376301
Illustration 2 g01376302
2/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
3/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2) .
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
Remove valve keepers (2) .
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4) .
8. If necessary, remove valve stem seals (5) .
9. Remove Tooling (A) .
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01376913
4/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01376302
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4) .
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4) .
4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5) .
5. Carefully release the pressure on Tooling (A) .
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
5/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:37:49 UTC+0800 2020
6/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767800
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
Typical Example
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
6. Slowly release the pressure on Tooling (B) .
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
8. Use Tooling (C) in order to remove valve stem seal (6) .
3/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g01376184
Illustration 5 g01376926
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head. Check the depth of valve (2) below the face of the cylinder
head. Refer to Testing and Adjusting, "Valve Depth - Inspect" for more information.
5/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5) .
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6) .
7. Carefully release the pressure on Tooling (B) .
8. Repeat Steps 2 through 7 for the remaining valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:38:44 UTC+0800 2020
6/6
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i04625005
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
Typical Example
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:39:40 UTC+0800 2020
4/4
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768108
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01384719
2. Remove bolts (1) .
3. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:40:36 UTC+0800 2020
2/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:41:31 UTC+0800 2020
2/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:42:27 UTC+0800 2020
2/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768201
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01384719
1/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 1. Install gasket (4) (not shown). Position engine oil cooler (3) and install bolts (2). Tighten
bolts (2) to a torque of 17 ± 2 N·m (13 ± 1 lb ft).
2. Install bolts (1). Tighten bolts (1) to a torque of 32 ± 3 N·m (24 ± 2 lb ft).
3. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant (ELC) - Change".
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 23:43:23 UTC+0800 2020
2/2
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR LKA
Configuration: 311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768236
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
A. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g01384786
1. Remove engine oil relief valve (1). Do not remove bolt (2) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
Illustration 2 g01384786
1. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of 49 ± 5
N·m (36 ± 4 lb ft). Do not remove bolt (2) .
2/3
311D LRR Excavator LKA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...