This document provides instructions for disassembling and assembling the final drive of a 318C excavator. The disassembly procedure involves using various tools to remove 31 parts from the final drive including the cover, planetary assembly, retaining rings, gears, bearings, seals and housing components. The assembly procedure instructs installing these 31 parts in reverse order and provides details on cleaning, lubricating and setting torque specifications.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR BTG
Configuration: 318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i02275023
Final Drive - Disassemble
SMCS - 4050-015
S/N - BTG1-UP
S/N - DAH1-UP
S/N - FAA1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 154-6360 Forcing Bolt 2
C 1P-2320 Combination Puller 1
D 138-7576 Link Bracket 2
E
8B-7554 Bearing Cup Puller Gp 1
7S-7786 Puller Leg 2
8B-7560 Step Plate 1
F 246-7504 Socket 1
G
6V-6080 Torque Multiplier Gp 1
9U-5006 Torque Wrench 1
H FT-2993 Reaction Bar 1
1/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. J 154-9316 Metric Thread File 1
K 1P-1864 Retaining Ring Pliers As 1
L 1U-8151 Drill Bit (5 mm) 1
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the final drive into a suitable container. Refer to Operation and Maintenance Manual,
"Capacities (Refill)".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
2. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g01139499
2/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 3. Fasten the final drive to Tooling (A), as shown. If necessary, remove the final drive
sprocket. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
The weight of the final drive is approximately 250 kg (550 lb).
Illustration 2 g01139500
4. Remove drain plugs (1) .
5. Remove bolts (2) .
Illustration 3 g01139501
6. Use Tooling (B) to separate cover (3) from the final drive. Remove cover (3) .
3/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01139502
7. Remove planetary assembly (4) .
8. Remove O-ring seal (5) .
Illustration 5 g01139503
9. Remove retaining ring (6) (not shown).
10. Use Tooling (C) in order to remove planetary gear (7) .
4/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g01139504
11. Remove retaining ring (8) and bearing (9) .
12. Repeat Steps 9 through 11 for the remaining planetary gears.
Illustration 7 g01139506
13. Remove retaining ring (11) and shaft (10) from carrier (12) .
Illustration 8 g01139507
14. Use Tooling (D) to remove ring gear (13). The weight of ring gear (13) is approximately 32
kg (70 lb).
5/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g01139508
Illustration 10 g01139509
15. Use Tooling (K) in order to remove retaining ring (14) .
16. Use Tooling (E) in order to remove planetary gear (15) .
Illustration 11 g01139510
17. Use a suitable press in order to remove bearings (16) from gear (15) .
6/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Note: If the bearings are removed, the bearings must be replaced with new bearings.
18. Repeat Steps 15 through 17 for the remaining planetary gears.
Illustration 12 g01139511
Illustration 13 g01139513
19. Remove O-ring seal (17) .
20. Straighten the tab on lock washers (18) .
21. Remove bolts (20), lock washers (18), and balls (21) from bearing retainer nut (19) .
7/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g01139514
22. Use Tooling (L) to clean the threads in the housing. Remove approximately 2.0 mm (0.08
inch) of material from the housing. This is done in order to prevent the retaining nut threads
from being damaged when retaining nut (19) is removed.
Illustration 15 g01139515
23. Install Tooling (F) on retainer nut (19). Install bolts (22) through Tooling (F) and into the
drilled holes in retainer nut (19) .
8/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g01139518
24. Install Tooling (F), (G), and (H) (not shown).
Illustration 17 g01139519
25. Use Tooling (D) and a suitable lifting device in order to remove support ring (23). The
weight of support ring (23) is approximately 23 kg (50 lb).
Illustration 18 g01139520
26. Remove bearing cone (24) from support ring (23) .
9/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01139775
27. Remove Duo-Cone seal (25) from support ring (23) .
Illustration 20 g01139776
28. Remove bearing cups (26) .
Illustration 21 g01139777
29. Remove bearing cone (27) from housing (28) .
10/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01139778
30. Remove Duo-Cone seal (29) from housing (28) .
Illustration 23 g01139779
31. Use Tooling (J) in order to repair any damaged threads on housing (28) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 28 11:07:54 UTC+0800 2020
11/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR BTG
Configuration: 318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i02275024
Final Drive - Assemble
SMCS - 4050-016
S/N - BTG1-UP
S/N - DAH1-UP
S/N - FAA1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
D 138-7576 Link Bracket 2
F 246-7504 Socket 1
G
6V-6080 Torque Multiplier Gp 1
9U-5006 Torque Wrench 1
H FT-2993 Reaction Bar 1
K 1P-1864 Retaining Ring Pliers As 1
M 1U-6396 O-Ring Assembly Compound 1
N 1U-6434 Duo-Cone Seal Installer As 1
P 246-7503 Punch 1
1/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring seal may not have the
same sealing properties as a new O-ring seal. Use Tooling (M) during the assembly procedure.
Illustration 1 g01139778
1. Use Tooling (N) to install Duo-Cone seal (29) onto housing (28) .
Illustration 2 g01139777
2. Install bearing cone (27) onto housing (28) .
2/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g01139776
3. Lower the temperature of bearing cups (26). Install bearing cups (26) into support ring (23) .
Illustration 4 g01139775
4. Use Tooling (N) to install Duo-Cone seal (25) into support ring (23) .
Illustration 5 g01139519
3/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Use Tooling (D) and a suitable lifting device in order to install support ring (23) onto
housing (28) .
Illustration 6 g01140214
6. Install bearing cone (24), as shown.
Illustration 7 g01140215
7. Install retainer nut (19) .
4/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g01139518
Illustration 9 g01139515
8. Install Tooling (F), (G), and (H) (not shown).
9. Install bolts (22) through Tooling (F) and into retainer nut (19). Tighten retainer nut (19) to
a torque of 3500 N·m (2581 lb ft).
Illustration 10 g01140089
5/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 10. Use Tooling (P) and a suitable hammer to make a dimple 0.9 mm to 1.25 mm (0.04 to 0.050
inch) deep in housing (28) .
Illustration 11 g01139513
Illustration 12 g01139511
11. Install balls (21), lock washers (18), and bolts (20) .
12. Fold the tab on lock washers (18) over bolts (20), as shown.
13. Install O-ring seal (17) .
6/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g01139510
14. Install bearing (16) into gear (15) .
Illustration 14 g01140222
15. Raise the temperature of gear (15). Install gear (15) onto housing (28) .
Note: Make sure that the chamfered side of the bearing is installed against the carrier.
Illustration 15 g01139508
7/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 16. Use Tooling (K) to install retaining ring (14) .
17. Repeat Steps 14 through 16 for the other two gears.
Illustration 16 g01139507
18. Use Tooling (D) and a suitable lifting device in order to install ring gear (13) onto housing
(28). The weight of ring gear (13) is approximately 32 kg (70 lb).
Illustration 17 g01139506
19. Install shaft (10) and retaining ring (11) onto carrier (12) .
8/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g01139504
20. Install bearing (9) and retaining ring (8) into the planetary gear.
Illustration 19 g01139889
21. Raise the temperature of planetary gear assembly (7). Install planetary gear assembly (7)
onto carrier (12) and install retaining ring (6) .
22. Repeat Steps 20 through 21 for the remaining two gears.
9/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g01139502
23. Install planetary assembly (4) into the final drive housing.
24. Install O-ring seal (5) .
Illustration 21 g01140103
25. Measure the distance between thrust button (3A) and shaft (10). The distance between shaft
(10) and thrust button (3A) should be 1.0 ± 0.5 mm (0.04 ± 0.02 inch).
10/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 22 g01139910
26. Install cover (3) and bolts (2). Tighten bolts (2) evenly to a torque of 295 ± 50 N·m (218 ±
37 lb ft).
27. Install drain plugs (1). Tighten drain plugs (1) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
28. Make sure that the final drive is filled with oil before the final drive is put back into service.
Refer to Operation and Maintenance Manual, "Capacities (Refill)".
29. Install the final drive sprocket if the sprocket was removed from the main housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install" in this manual for
the installation of the final drive sprocket.
30. Remove the final drive from Tooling (A). The weight of the final drive is approximately
250 kg (550 lb).
End By: Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 28 11:08:54 UTC+0800 2020
11/11
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR BTG
Configuration: 318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i07192988
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C - Loctite C5A Copper Anti-Seize -
Table 2
Torque Values of Bolts (3)
Bolt Size Torque
M16 90 ± 15 N·m (66 ± 11 lb ft) and turn an additional angle of 60 ± 5 degrees.
M20 150 ± 25 N·m (111 ± 18 lb ft) and turn an additional angle of 55 ± 5 degrees.
M24 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 45 ± 5 degrees.
M30 500 ± 50 N·m (369 ± 37 lb ft) and turn an additional angle of 50 ± 5 degrees.
1/3
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00712767
1. Attach Tooling (B) and a suitable lifting device to final drive (1). The weight of final drive
(1) and the sprocket is approximately 312 kg (688 lb). Position the final drive in the frame.
Illustration 2 g00712737
Note: Make sure that bolt holes (2) for the travel motor are in the correct position.
Note: Make sure that bolts (3), the washers, the motor housing, and the frame are clean and
free of protective coating and oil.
2. Before assembly remove all compounds, oil, and dust from the female threads.
3. Apply Tooling (C) to the threads of bolt (3). Install bolts (3) and the washers in the final
drive. Tighten bolts (3) to a torque specified in Table 2.
4. Refer to Service Magazine, M0083843, "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on All Excavators" for more detail information.
5. Remove Tooling (B) and the suitable lifting device from the final drive.
2/3
318C Excavators BTG00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...