This document provides an overview of Neboneed Farhadi's experience portfolio, including: - A Bachelor's degree in Aerospace Engineering and over 1.5 years of industry experience. - Coursework and projects in areas like aircraft design, CAD, CFD, and robotics. - Recent engineering work experience at Bloom Energy in remote monitoring and technical support. - Additional non-engineering internship experience in hydrology data analysis.

1. NEBONEED FARHADI
EXPERIENCE PORTFOLIO

2. INDEX
About Me ------------------------------------------------------------3
Overview ------------------------------------------------------------4
Courses Taken -----------------------------------------------------5
Engineering Projects
Aircraft Design ----------------------------------------------6
CAD for Mechanical Engineers Course ------------------9
CFD Rocket Nose ----------------------------------------------11
UAV Arduino -----------------------------------------------------13
Rocket Assembly ----------------------------------------------14
Engineering Related Work Experience
Bloom Energy -----------------------------------------------------15
Non-Engineering Related Work Experience
Turlock Irrigation District ---------------------------------------17
Team Development ---------------------------------------18

3. ABOUT ME
• Bachelor of Science in Aerospace Engineering
• San Jose State University Graduate May 2018
• Born in USA
• No dual citizenship
3

4. OVERVIEW
• Aeronautical engineering specialization
• 1.5 total years of industry experience
• 1 year of CAD experience (SolidWorks, CREO, GD&T)
• 7 years of customer service
4

5. ENGINEERING COURSES TAKEN
5
• Fluid Mechanics: Aerodynamics 1&2, Computational
Fluid Dynamics
• Thermodynamics: Aerothermodynamics, Aerospace
Propulsion
• Structures: Statics, Aircraft Structural Analysis 1&2
• Mechanics: Flight Mechanics, Rigid Body Dynamics,
Vector Based Dynamics
• Control Theory: Aerospace Automatic Control System
Design, Aerospace Vehicle Dynamics and Control,
Introduction to UAV Design
• Computer Aided Design: Design and Graphics (CREO),
CAD for Mechanical Engineering (SolidWorks)
• Software and Electrical Engineering: Introduction to
Circuit Design, Programming for Aerospace Engineering
(C,MATLAB)

6. AIRCRAFT DESIGN PROJECT
 Software Used: Excel Spreadsheets
• Mission Objective was to carry 8 lbs. of payload (sand)
and do a precision bombing run on a designated area
• Constraints: aircraft must be less than 55lb, have an
internal combustion engine, LiPo or LiFE battery, and
have a 2.4GHz radio
• Primarily responsible for the tail design portion of the
aircraft
• Utilized various aircraft design sources to assist in
designing the tail
• Performed trade studies to determine the best possible
design given the rules and regulations
6

7. AIRCRAFT DESIGN PROJECT
CONT.
Engineering GD&T Drawing
• Fully responsible for all critical
engineering drawings needed to pass
the design screening
• Applied GD&T to the aircraft to show
electronic equipment locations, CG
location, and the overall dimensions
 Software Used: SolidWorks
7

8. AIRCRAFT DESIGN PROJECT
CONT.
 CFD Software Used: SolidWorks
• Other project responsibilities:
- Created the entire final PowerPoint for the team
- Created CFD simulation of the aircraft to prevent
downwash issues during final design phase
- Assisted in improving the payload bay design
8

9. CAD FOR MECHANICAL
ENGINEERS COURSE PROJECTS
(GUIDE- ROD)
• Utilized the Fundamentals of Assembly Modeling (Bottom-Up)
along with creating Standard Mates, Smart Mates, and the Quick
procedure.
• Created assemblies, edited component dimensions, addressed
tolerance and fit, and incorporated design changes into
assembly
• Created the GUIDE-ROD drawing with Custom Properties,
and Exploded Isometric view with a Bill of Materials and balloon
 Software Used: SolidWorks
 Books Used: Engineering Design with SolidWorks 2016 and
SolidWorks 2016 Intermediate Skills
9

10. CAD FOR MECHANICAL
ENGINEERS COURSE PROJECTS
(FLASHLIGHT)
• Created the battery and battery plate part with the
Extruded Boss/Base feature and the Instant3D tool
• Utilized:
- Extruded Boss/Base, Extruded Cut, Revolved Base,
Revolved Cut, Dome, Shell, Fillet and created the lens
and bulb with the Revolved Boss/Base feature
- The Mold tools to create the cavity plate for the
battery plate
- Swept Boss/Base, Lofted Boss/Base, Rib, Linear
Pattern, Circular Pattern, Draft and Dome for the o-ring,
switch, lens cap and housing.
10

11. CFD ROCKET NOSE PROJECT
(ARIAN 64 ROCKET)
 Software Used: SolidWorks, ESI Grid Pro and Fortran
• The purpose of this project was to analyze the
axisymmetric behavior of a rocket at subsonic speeds
(Mach 0.9) utilizing department software and comparing
the results to a similar experiment
• Utilized SolidWorks to create the outer shape of the rocket
and inserted it into Grid Pro to create the CFD mesh
• ESI Fortran was then used to create the simulation
11

12. CFD ROCKET NOSE PROJECT
(ARIAN 64 ROCKET) CONT.
• Simulation generated Mach and pressure contours
• 5000 cycles for 100 seconds
• Naiver stokes with higher order implicate non iterative solver u
• Project results were similar when compared to the experiment
12

13. UAV ARDUINO PROJECT
 Software Used: Arduino, C ++
• Objective of the project was to install an IMU on an
Arduino to simulate an UAV’s pitch and roll dynamics
using microcontrollers
• Used Arduino libraries to code an IMU and output raw
acceleration/gyro values
• Assisted in coding a complimentary filter using online
resources
13

14. ROCKET CLUB PROJECT
• Worked with 10 Rocket Club members to assemble a rocket
• Utilized tools and materials like hand drills, dremels, sandpaper,
glues, fiberglass, and wood
• Enhanced attention to detail when critical parts of the rocket wer
being assembled
• Launched rocket successfully and obtained level 1 rocketry licens
14

15. BLOOM ENERGY: REMOTE
MONITORING AND TECHNICAL
SUPPORT ENGINEER
 Software Used: Bloom Energy HMI, Pi Processbook,
Excel Spreadsheets, Outlook, PowerPoint
• Duration: July 2018 – March 2019
• Job Role: monitor and troubleshoot the fuel cell power
plant systems installed at customer sites from the
Remote Monitoring Control Center
• Monitored global installed fleet and continuously
gathered and analyzed operating data down to the
individual stack level to evaluate health and to optimize
performance
15

16. BLOOM ENERGY: REMOTE
MONITORING AND TECHNICAL
SUPPORT ENGINEER CONT.
• Gained experience in working with:
- Mechanical Systems
- High Voltage Electrical Systems
- Electrochemical Systems
- Fuel and Water Systems
- Communication Systems
• Read and understood P&IDs and PFDs of power
plants
• Analyzed and controlled thermal-fluid components
• Utilized effective communication skills with
engineers, operators, field service, product support ,
VP, and customers 16

17. TURLOCK IRRIGATION DISTRICT:
HYDROLOGY DATA INTERN
 Software Used: Excel Spreadsheets, PowerPoint,
Outlook, OneNote, Visio, WISKI
• Duration: August 2019 – February 2020
• Job Duties: To assist hydrologists in learning how to use
the WISKI program, and analyze data given by the chief
hydrologist to assist department research
• Updated their WISKI program and created department
procedures
• Researched and reverse engineered federal and state
water operations to determine how they were effecting
TID’s dam operations 17

18. TEAM DEVELOPMENT
• 4 years of teamwork experience working on projects or in a job
that required working in a team
• Excellent communication skills varying from emails, reports writ
phone calls and in person interaction
• Experienced in presenting engineering or other technical materi
a wide variety of audiences
18