SlideShare a Scribd company logo
1 of 8
Anti-mold
SOP upon
shit happening
处理过程中用到两种药水
1 先用Cleaner(酶清洁剂 ) 2在用Solution(消毒水)使用说明:
1. Cleaner酶清
洁剂须要1:30加
入纯净水稀释,
是清洁鞋面霉菌
面专用。
2. Solution不需
要添加任何药水
和水,直接倒入
喷枪内,对准成
品鞋喷洒使用。
1 2
Cleaner酶清洁剂
用水稀释Sporicidin酶清洁剂
Ratio:1:30(1:30的纯净
水)
清洁鞋面使用。
1.打开内盒取出鞋子的包装物,(换掉纸团和包装纸是防止再次感染)
2.如果鞋子是用胶袋装,胶袋也必须换掉(防止再次感染 ) 。
3.可以使 用Solution (消毒液)湿布巾涂抹内盒的里面所有部位,每次涂
抹最多20个盒子后,要更换一块新的棉布和消毒湿布巾。
1.取鞋子内纸团和
包装纸(换掉包装
材料)。
2.松开鞋带。
使用Solution湿
布巾擦内盒内
所有的部位。
1先给鞋带打开用Cleaner对比好的清洁剂去清洁鞋面发霉的
位置(包括鞋带.鞋垫和和鞋子内里),酶清洁剂需要涂在需
要清洁的表面,并确保表面湿度维达最少3分钟。
洗鞋面专用
•.刷子每湛一
次酶清洁剂,
使用面积不能
大于1-2平方米,
保持刷子上面
有药水使用为
原则。刷子上
没有药水时,
必须要对刷子
清洁一次,再
来使用酶清洁
剂洗鞋面。
使用Solution(消毒水)喷洒鞋面和鞋口内里
消毒水要在斜面上喷洒湿润,保持湿润时间要10分钟。
要自然风干。
1 给Solution倒
入喷枪内,对准
鞋面表面和内里
(鞋翅两侧内)
要湿润均匀喷到
位。表面湿润要
10分钟后自然
风干。
鞋面干燥后方可进行塞纸团.整理鞋带和包装。
包装要点:
1.鞋子内的纸团必须使用新的。 2.内盒的防霉片必须
再增加一片。
3.包装纸必须使用新的。
塞新纸团
整理鞋带
防霉片要
增加一片
换用新的
包装纸
GOOD LUCK!
Thanks

More Related Content

More from Teddy Pai

Teddy' Pai CV.doc
Teddy' Pai CV.docTeddy' Pai CV.doc
Teddy' Pai CV.docTeddy Pai
 
CISA MATRIX-2022 Q1.pdf
CISA MATRIX-2022 Q1.pdfCISA MATRIX-2022 Q1.pdf
CISA MATRIX-2022 Q1.pdfTeddy Pai
 
Zenith plus ltd profile
Zenith plus ltd profileZenith plus ltd profile
Zenith plus ltd profileTeddy Pai
 
Dv update  july
Dv update  julyDv update  july
Dv update  julyTeddy Pai
 
Mold proof action plan
Mold proof action planMold proof action plan
Mold proof action planTeddy Pai
 
Recycle car tyre outsole making process
Recycle car tyre outsole making processRecycle car tyre outsole making process
Recycle car tyre outsole making processTeddy Pai
 
Pet webbing making process
Pet webbing making processPet webbing making process
Pet webbing making processTeddy Pai
 
Stitching margin improvement project
Stitching margin improvement project  Stitching margin improvement project
Stitching margin improvement project Teddy Pai
 
Digital woven introduction 2015 aug. 25
Digital woven introduction 2015 aug. 25Digital woven introduction 2015 aug. 25
Digital woven introduction 2015 aug. 25Teddy Pai
 
Digital creation black magic add-up
Digital creation black magic add-upDigital creation black magic add-up
Digital creation black magic add-upTeddy Pai
 
Matter in all kind of applications
Matter in all kind of applicationsMatter in all kind of applications
Matter in all kind of applicationsTeddy Pai
 
Rmat factory profile xyl
Rmat factory profile xylRmat factory profile xyl
Rmat factory profile xylTeddy Pai
 
New injection technology-rubber
New injection technology-rubberNew injection technology-rubber
New injection technology-rubberTeddy Pai
 
Pet webbing making process
Pet webbing making processPet webbing making process
Pet webbing making processTeddy Pai
 
Recycle car tyre outsole making process
Recycle car tyre outsole making processRecycle car tyre outsole making process
Recycle car tyre outsole making processTeddy Pai
 
Chrome free leather presentation
Chrome free leather presentationChrome free leather presentation
Chrome free leather presentationTeddy Pai
 
3 D technology-new manner to turn a quick turnaround prototyping.
3 D technology-new manner to turn a quick turnaround prototyping.3 D technology-new manner to turn a quick turnaround prototyping.
3 D technology-new manner to turn a quick turnaround prototyping.Teddy Pai
 
It does MATTER to us-XYL's statement.
It does MATTER to us-XYL's statement.It does MATTER to us-XYL's statement.
It does MATTER to us-XYL's statement.Teddy Pai
 
Automation and standardizing-work out constrains of labor conditions.
Automation and standardizing-work out constrains of labor conditions. Automation and standardizing-work out constrains of labor conditions.
Automation and standardizing-work out constrains of labor conditions. Teddy Pai
 

More from Teddy Pai (20)

Teddy' Pai CV.doc
Teddy' Pai CV.docTeddy' Pai CV.doc
Teddy' Pai CV.doc
 
CISA MATRIX-2022 Q1.pdf
CISA MATRIX-2022 Q1.pdfCISA MATRIX-2022 Q1.pdf
CISA MATRIX-2022 Q1.pdf
 
Zenith plus ltd profile
Zenith plus ltd profileZenith plus ltd profile
Zenith plus ltd profile
 
Dv update  july
Dv update  julyDv update  july
Dv update  july
 
R & D
R & DR & D
R & D
 
Mold proof action plan
Mold proof action planMold proof action plan
Mold proof action plan
 
Recycle car tyre outsole making process
Recycle car tyre outsole making processRecycle car tyre outsole making process
Recycle car tyre outsole making process
 
Pet webbing making process
Pet webbing making processPet webbing making process
Pet webbing making process
 
Stitching margin improvement project
Stitching margin improvement project  Stitching margin improvement project
Stitching margin improvement project
 
Digital woven introduction 2015 aug. 25
Digital woven introduction 2015 aug. 25Digital woven introduction 2015 aug. 25
Digital woven introduction 2015 aug. 25
 
Digital creation black magic add-up
Digital creation black magic add-upDigital creation black magic add-up
Digital creation black magic add-up
 
Matter in all kind of applications
Matter in all kind of applicationsMatter in all kind of applications
Matter in all kind of applications
 
Rmat factory profile xyl
Rmat factory profile xylRmat factory profile xyl
Rmat factory profile xyl
 
New injection technology-rubber
New injection technology-rubberNew injection technology-rubber
New injection technology-rubber
 
Pet webbing making process
Pet webbing making processPet webbing making process
Pet webbing making process
 
Recycle car tyre outsole making process
Recycle car tyre outsole making processRecycle car tyre outsole making process
Recycle car tyre outsole making process
 
Chrome free leather presentation
Chrome free leather presentationChrome free leather presentation
Chrome free leather presentation
 
3 D technology-new manner to turn a quick turnaround prototyping.
3 D technology-new manner to turn a quick turnaround prototyping.3 D technology-new manner to turn a quick turnaround prototyping.
3 D technology-new manner to turn a quick turnaround prototyping.
 
It does MATTER to us-XYL's statement.
It does MATTER to us-XYL's statement.It does MATTER to us-XYL's statement.
It does MATTER to us-XYL's statement.
 
Automation and standardizing-work out constrains of labor conditions.
Automation and standardizing-work out constrains of labor conditions. Automation and standardizing-work out constrains of labor conditions.
Automation and standardizing-work out constrains of labor conditions.
 

Molding control