LOCTITE 420 INSTANT ADHESIVE is a general purpose cyanoacrylate wicking type plastic bonder. Mil Spec: Mil-A-46050C Type II Class I. Commercial Item Description A-A-3097: Type II Class 1.
LOCTITE 574 is an acrylic-based anaerobic sealant that cures in the absence of air between close-fitting metal surfaces. It is a thixotropic paste that seals close-fitting joints and flanges to provide immediate resistance to low pressures. The technical data sheet provides details on product description, typical properties before and after curing, curing performance under different conditions, environmental resistance, instructions for use, and specifications.
LOCTITE® SF 7063TM is a solvent-based cleaner for removing contaminants from surfaces to prepare them for bonding with LOCTITE® adhesives. It has a low viscosity and dries quickly. SF 7063TM cleans without affecting the curing or strength of LOCTITE® adhesives. Proper handling is required due to its flammable nature. Users should test compatibility with plastics before use and allow full drying to prevent solvent entrapment.
LOCTITE® SF 7855TM is a heavy-duty hand cleaner formulated to remove difficult soils like paints and adhesives. It contains skin conditioning agents like aloe vera and vitamins to moisturize hands. The product has a citrus scent and fine abrasives that aid cleaning without affecting skin with frequent use. Directions instruct to dispense onto dry hands and rub until dirt dissolves, then wipe or rinse clean.
This technical data sheet provides information on LOCTITE® SF 7850TM, a natural hand cleaner containing d-limonene from oranges. It is an off-white, viscous lotion that cleans hands without water by dissolving dirt and grease. In addition to d-limonene, it contains aloe vera, lanolin, and jojoba oil for skin conditioning and extra fine abrasives that clean deep in the pores. The data sheet provides instructions for use and storage information.
LOCTITE® 5188TM is a one-part, acrylic-based anaerobic sealant that cures in the absence of air between close-fitting metal surfaces. It is designed for sealing rigid metal flanged connections, especially those exposed to minor oil contamination. It cures quickly and develops handling strength within 30 minutes, with full strength achieved after 72 hours. The sealant remains flexible even after exposure to high temperatures and has good adhesion to metals like steel and aluminum. It can seal gaps up to 0.25mm and resist pressures immediately after application while uncured.
LOCTITE 270 MOD is a one-part, acrylic-based threadlocking adhesive that cures anaerobically. It is green liquid that is particularly suitable for permanently locking and sealing threaded fasteners in heavy-duty applications. The adhesive cures when confined in the absence of air between close-fitting metal surfaces. It provides high strength bonding and prevents loosening from shock and vibration. The technical data sheet provides information on the product's properties, curing performance under different conditions, typical performance of cured material, and environmental resistance.
LOCTITE 401 is a one-part cyanoacrylate adhesive that cures rapidly when exposed to moisture in the air. It bonds a variety of materials including wood, paper, leather, fabric, plastics and metals. The adhesive has a low viscosity, cures within seconds to minutes depending on the substrate, and reaches full strength within 24 hours. It is particularly suited for bonding porous materials.
This technical data sheet provides information on LOCTITE SF 7840, a concentrated, biodegradable cleaner and degreaser. It is an aqueous-based product that contains no hazardous solvents. It can be diluted with water for cleaning a variety of surfaces and removing substances like grease, oils, food stains and more. Recommended dilution levels vary depending on the application and level of cleaning required, from 1:1 for heavy cleaning to 1:128 for light cleaning. Precautions are noted to avoid using on painted surfaces at low dilutions or where cleaner residues could affect curing of anaerobic products.
LOCTITE 574 is an acrylic-based anaerobic sealant that cures in the absence of air between close-fitting metal surfaces. It is a thixotropic paste that seals close-fitting joints and flanges to provide immediate resistance to low pressures. The technical data sheet provides details on product description, typical properties before and after curing, curing performance under different conditions, environmental resistance, instructions for use, and specifications.
LOCTITE® SF 7063TM is a solvent-based cleaner for removing contaminants from surfaces to prepare them for bonding with LOCTITE® adhesives. It has a low viscosity and dries quickly. SF 7063TM cleans without affecting the curing or strength of LOCTITE® adhesives. Proper handling is required due to its flammable nature. Users should test compatibility with plastics before use and allow full drying to prevent solvent entrapment.
LOCTITE® SF 7855TM is a heavy-duty hand cleaner formulated to remove difficult soils like paints and adhesives. It contains skin conditioning agents like aloe vera and vitamins to moisturize hands. The product has a citrus scent and fine abrasives that aid cleaning without affecting skin with frequent use. Directions instruct to dispense onto dry hands and rub until dirt dissolves, then wipe or rinse clean.
This technical data sheet provides information on LOCTITE® SF 7850TM, a natural hand cleaner containing d-limonene from oranges. It is an off-white, viscous lotion that cleans hands without water by dissolving dirt and grease. In addition to d-limonene, it contains aloe vera, lanolin, and jojoba oil for skin conditioning and extra fine abrasives that clean deep in the pores. The data sheet provides instructions for use and storage information.
LOCTITE® 5188TM is a one-part, acrylic-based anaerobic sealant that cures in the absence of air between close-fitting metal surfaces. It is designed for sealing rigid metal flanged connections, especially those exposed to minor oil contamination. It cures quickly and develops handling strength within 30 minutes, with full strength achieved after 72 hours. The sealant remains flexible even after exposure to high temperatures and has good adhesion to metals like steel and aluminum. It can seal gaps up to 0.25mm and resist pressures immediately after application while uncured.
LOCTITE 270 MOD is a one-part, acrylic-based threadlocking adhesive that cures anaerobically. It is green liquid that is particularly suitable for permanently locking and sealing threaded fasteners in heavy-duty applications. The adhesive cures when confined in the absence of air between close-fitting metal surfaces. It provides high strength bonding and prevents loosening from shock and vibration. The technical data sheet provides information on the product's properties, curing performance under different conditions, typical performance of cured material, and environmental resistance.
LOCTITE 401 is a one-part cyanoacrylate adhesive that cures rapidly when exposed to moisture in the air. It bonds a variety of materials including wood, paper, leather, fabric, plastics and metals. The adhesive has a low viscosity, cures within seconds to minutes depending on the substrate, and reaches full strength within 24 hours. It is particularly suited for bonding porous materials.
This technical data sheet provides information on LOCTITE SF 7840, a concentrated, biodegradable cleaner and degreaser. It is an aqueous-based product that contains no hazardous solvents. It can be diluted with water for cleaning a variety of surfaces and removing substances like grease, oils, food stains and more. Recommended dilution levels vary depending on the application and level of cleaning required, from 1:1 for heavy cleaning to 1:128 for light cleaning. Precautions are noted to avoid using on painted surfaces at low dilutions or where cleaner residues could affect curing of anaerobic products.
LOCTITE SF 7200 is an aerosol cleaner designed to aid in the removal of cured chemical gaskets. It works by softening gasket materials on flanges, eliminating excessive scraping. Once applied, it forms a foam layer preventing it from running off while working. It is suitable for removing gaskets from metal flanges, particularly aluminum, without damaging flange surfaces. Typical applications include removing all types of chemical gaskets from metal flanges.
LOCTITE® SF 7039TM is a contact cleaner spray that is colorless and odorless. It contains hydrocarbons and alcohols and uses carbon dioxide as a propellant. It cleans electrical contacts without damaging existing coatings and leaves a water-repellent residue. It is intended to clean contacts exposed to moisture or contamination and works on surfaces from -30°C to 50°C. Directions for use involve shaking the can and spraying from 20-30cm onto the target area.
LOCTITE Black Maxx 300 is a one-component, RTV silicone gasket sealant. It has excellent resistance to automotive engine oils and high adhesion strength. It cures at room temperature within 40 minutes to form a flexible, thixotropic paste with a Shore A hardness of 30. The sealant has over 400% elongation and tensile strengths over 1.7 N/mm2 at cure and 0.6-1.0 N/mm2 at 100% elongation. It is packaged in 70ml tubes and has a shelf life of at least one year when stored between 8-21°C.
PATT Filtration produces polymer filtration systems to remove contaminants from molten plastics. Their ROTARY III Constant Pressure Drop Continuous filtration system uses a revolving disk with screens to filter plastics while maintaining constant pressure. PATT emphasizes product quality, customer satisfaction, and custom engineering solutions. They have become a leader in polymer filtration through ongoing research and adapting their technologies to customers' specific needs.
LOCTITE® 222 is a low strength, thixotropic, acrylic threadlocking adhesive that cures anaerobically. It is designed for locking and sealing threaded fasteners that require easy disassembly with hand tools. The adhesive cures when confined in the absence of air between close fitting metal surfaces and prevents loosening from shock and vibration, particularly suitable for set screws and small diameter fasteners. The product data sheet provides details on typical properties, curing performance, environmental resistance, directions for use, storage, and other technical information.
This document provides information on Epibond® 100 A/B, a two-component, extrudable, heat curing epoxy structural adhesive designed for aerospace applications requiring high heat resistance and retention of strength. It is characterized by high lap shear strength, a glass transition temperature above 120°C, and service temperatures up to 150°C. The adhesive spreads easily, has a long working time, and its moderate cure cycle involves heating to 65°C for 1 hour then 95°C for 5 hours. It bonds composite and metal substrates commonly used in aerospace and maintains high strength values at elevated temperatures.
Rust-X is a global leader in corrosion prevention solutions. It has over 10,000 customers served across multiple manufacturing locations globally. The document provides details about Rust-X's product range, manufacturing footprint, customer segments, and growth over the past decades from a small firm to a large corporation with a presence in over 35 countries.
This technical data sheet provides information on LOCTITE® LB 8201TM, including that it is a universal penetrating liquid that frees, lubricates, cleans, and prevents corrosion on machinery. It can be used to free seized or corroded parts and provides light lubrication. The product is a yellow-brown liquid with properties such as a density of 0.808 to 0.828 g/ml and viscosity of 17.5 cSt at 50°C. Use and storage instructions are also provided.
NTPT selected Huntsman Advanced Materials' prepreg system to produce ultra-thin prepreg tapes for luxury watch cases. Huntsman's building blocks were chosen for their ability to meet the criteria for manufacturing very thin tapes and for providing excellent filament bearing properties and resistance to delamination. This allowed the cured tapes to be easily machinable like metal. The collaboration between Huntsman and NTPT was key to developing a high quality, lightweight watch case through matching the proper materials and process.
LOCTITE® LB 8101TM is an adhesive grease used to lubricate open mechanical systems like chains, gears, screws and cables. It protects against water and wear while resisting high pressures and centrifugal forces. The grease is amber colored with an oily odor, and is sprayed from an aerosol can. It is designed to lubricate parts operating from -30°C to +170°C.
This safety data sheet provides information on Loctite 270 adhesive. It lists the product identifier and supplier contact information in section 1. Section 2 describes the product as causing skin, eye, and respiratory irritation and being a skin sensitizer. The product contains hazardous substances like 3,3,5 trimethylcyclohexyl methacrylate and cumene hydroperoxide that are classified and listed in section 3. Section 4 provides first aid measures for potential exposure.
This document provides a safety data sheet for Loctite SuperGlue Gel -454-. It contains information on product identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection. The key hazards identified are skin and eye irritation. It contains ethyl 2-cyanoacrylate as the main component and small amounts of hydroquinone and bis(2-hydroxy-3-tert-butyl-5-methylphenyl)methane. Personal protective equipment such as gloves and breathing masks are recommended when handling the product.
This document provides information on tooling solutions from Huntsman Advanced Materials for various applications. It discusses their range of systems for producing master models, plugs, PU casting, and prototyping which are used globally in industries like automotive, aerospace, and wind energy. The document also summarizes their seamless modeling pastes, gelcoats, laminating systems, and casting systems for standard tooling and composite tooling. It provides details on specific products, their properties, applications and benefits in tables to help customers identify the best solution for their needs.
This document summarizes Huntsman Advanced Materials' composite solutions for the automotive industry, including fast curing resin systems for body structures and leaf springs. It outlines various epoxy resin systems tailored for different composite manufacturing processes like wet compression molding, resin transfer molding, and a new dynamic fluid compression molding process. It also provides property data and descriptions of resin systems qualified for automotive wheel and preform production. Simulation tools are discussed which can optimize composite part design and manufacturing.
LOCTITE LB 8021 is a general purpose, low viscosity silicone oil used for lubricating metal and non-metal surfaces between -30°C and +150°C. It has a clear liquid appearance and 350 mPa·s viscosity. The product is a silicone oil dispersed in a propane/butane propellant and is used to lubricate parts like guides, conveyors and cutting knives. It is also suitable as a mold release agent and has approval for incidental food contact.
Huntsman Advanced Materials produces a range of thermosetting composite resin systems for various manufacturing industries. They offer technical support and expertise to help customers optimize processes and develop customized solutions. Their product range includes resin formulations for wet layup, resin transfer molding, infusion, filament winding, and other composites manufacturing methods. Huntsman works with customers to select the best resin system for their needs, improve quality and performance, and accelerate time to market.
These two products, Araldite® 1570 FST A/B and Epibond® 8000 FR A/B, are two-component epoxy structural adhesives designed for aerospace applications requiring flame, smoke and toxicity properties. Araldite® 1570 FST A/B is a semi-rigid adhesive with high elongation at break and long pot life at room temperature. Epibond® 8000 FR A/B is a rigid adhesive with high lap shear strength and accelerated cure at room temperature. Both adhesives meet FAR 25.853 requirements for flame, smoke and toxicity.
This safety data sheet provides information on LOCTITE 222 anaerobic adhesive. It lists the product identifier and supplier contact information. The product contains cumene hydroperoxide and other hazardous ingredients. It is classified as causing serious eye irritation and respiratory irritation. Exposure guidelines and personal protective equipment requirements are also outlined, including the need for gloves, safety glasses and adequate ventilation when handling the product.
This document provides technical information about AGILITYTM 1000 Performance LDPE, a high pressure low density polyethylene resin designed for faster blown film processing and higher output rates when blended with LLDPE resins. Some key characteristics include faster processing, maintaining bubble stability at higher rates, and excellent shrink properties. Physical and performance properties of films made from this resin are provided, as well as processing guidelines for blown film fabrication. Product stewardship and regulatory information is also included.
This technical data sheet provides information on Loctite 454, a cyanoacrylate adhesive. It is a one-part, thixotropic gel adhesive that cures rapidly with humidity. It can bond a variety of substrates including metals, plastics, elastomers, wood, leather, and fabrics. The gel consistency prevents run-off on vertical surfaces. Typical properties include a fixture time of less than one minute for many substrates and tensile strengths up to 15.1 MPa after curing for 72 hours. It also has good chemical and solvent resistance as well as heat resistance. Usage instructions and precautions are provided.
LOCTITE LB 8040 is a mineral oil formulation that can freeze and instantly crack rust at -43°C, allowing the oil to penetrate rust and lubricate seized metal parts. It sprays onto parts from a pressurized container. When sprayed onto rusted fasteners and allowed to react for 1-2 minutes, the frozen rust cracks and the oil penetrates to free seized parts while leaving them lubricated and protected from corrosion. The product comes in an amber-colored liquid with a density of 0.6 g/ml and viscosity below 5 mPa·s.
LOCTITE SF 7200 is an aerosol cleaner designed to aid in the removal of cured chemical gaskets. It works by softening gasket materials on flanges, eliminating excessive scraping. Once applied, it forms a foam layer preventing it from running off while working. It is suitable for removing gaskets from metal flanges, particularly aluminum, without damaging flange surfaces. Typical applications include removing all types of chemical gaskets from metal flanges.
LOCTITE® SF 7039TM is a contact cleaner spray that is colorless and odorless. It contains hydrocarbons and alcohols and uses carbon dioxide as a propellant. It cleans electrical contacts without damaging existing coatings and leaves a water-repellent residue. It is intended to clean contacts exposed to moisture or contamination and works on surfaces from -30°C to 50°C. Directions for use involve shaking the can and spraying from 20-30cm onto the target area.
LOCTITE Black Maxx 300 is a one-component, RTV silicone gasket sealant. It has excellent resistance to automotive engine oils and high adhesion strength. It cures at room temperature within 40 minutes to form a flexible, thixotropic paste with a Shore A hardness of 30. The sealant has over 400% elongation and tensile strengths over 1.7 N/mm2 at cure and 0.6-1.0 N/mm2 at 100% elongation. It is packaged in 70ml tubes and has a shelf life of at least one year when stored between 8-21°C.
PATT Filtration produces polymer filtration systems to remove contaminants from molten plastics. Their ROTARY III Constant Pressure Drop Continuous filtration system uses a revolving disk with screens to filter plastics while maintaining constant pressure. PATT emphasizes product quality, customer satisfaction, and custom engineering solutions. They have become a leader in polymer filtration through ongoing research and adapting their technologies to customers' specific needs.
LOCTITE® 222 is a low strength, thixotropic, acrylic threadlocking adhesive that cures anaerobically. It is designed for locking and sealing threaded fasteners that require easy disassembly with hand tools. The adhesive cures when confined in the absence of air between close fitting metal surfaces and prevents loosening from shock and vibration, particularly suitable for set screws and small diameter fasteners. The product data sheet provides details on typical properties, curing performance, environmental resistance, directions for use, storage, and other technical information.
This document provides information on Epibond® 100 A/B, a two-component, extrudable, heat curing epoxy structural adhesive designed for aerospace applications requiring high heat resistance and retention of strength. It is characterized by high lap shear strength, a glass transition temperature above 120°C, and service temperatures up to 150°C. The adhesive spreads easily, has a long working time, and its moderate cure cycle involves heating to 65°C for 1 hour then 95°C for 5 hours. It bonds composite and metal substrates commonly used in aerospace and maintains high strength values at elevated temperatures.
Rust-X is a global leader in corrosion prevention solutions. It has over 10,000 customers served across multiple manufacturing locations globally. The document provides details about Rust-X's product range, manufacturing footprint, customer segments, and growth over the past decades from a small firm to a large corporation with a presence in over 35 countries.
This technical data sheet provides information on LOCTITE® LB 8201TM, including that it is a universal penetrating liquid that frees, lubricates, cleans, and prevents corrosion on machinery. It can be used to free seized or corroded parts and provides light lubrication. The product is a yellow-brown liquid with properties such as a density of 0.808 to 0.828 g/ml and viscosity of 17.5 cSt at 50°C. Use and storage instructions are also provided.
NTPT selected Huntsman Advanced Materials' prepreg system to produce ultra-thin prepreg tapes for luxury watch cases. Huntsman's building blocks were chosen for their ability to meet the criteria for manufacturing very thin tapes and for providing excellent filament bearing properties and resistance to delamination. This allowed the cured tapes to be easily machinable like metal. The collaboration between Huntsman and NTPT was key to developing a high quality, lightweight watch case through matching the proper materials and process.
LOCTITE® LB 8101TM is an adhesive grease used to lubricate open mechanical systems like chains, gears, screws and cables. It protects against water and wear while resisting high pressures and centrifugal forces. The grease is amber colored with an oily odor, and is sprayed from an aerosol can. It is designed to lubricate parts operating from -30°C to +170°C.
This safety data sheet provides information on Loctite 270 adhesive. It lists the product identifier and supplier contact information in section 1. Section 2 describes the product as causing skin, eye, and respiratory irritation and being a skin sensitizer. The product contains hazardous substances like 3,3,5 trimethylcyclohexyl methacrylate and cumene hydroperoxide that are classified and listed in section 3. Section 4 provides first aid measures for potential exposure.
This document provides a safety data sheet for Loctite SuperGlue Gel -454-. It contains information on product identification, hazards, composition, first aid measures, firefighting measures, accidental release measures, handling and storage, exposure controls and personal protection. The key hazards identified are skin and eye irritation. It contains ethyl 2-cyanoacrylate as the main component and small amounts of hydroquinone and bis(2-hydroxy-3-tert-butyl-5-methylphenyl)methane. Personal protective equipment such as gloves and breathing masks are recommended when handling the product.
This document provides information on tooling solutions from Huntsman Advanced Materials for various applications. It discusses their range of systems for producing master models, plugs, PU casting, and prototyping which are used globally in industries like automotive, aerospace, and wind energy. The document also summarizes their seamless modeling pastes, gelcoats, laminating systems, and casting systems for standard tooling and composite tooling. It provides details on specific products, their properties, applications and benefits in tables to help customers identify the best solution for their needs.
This document summarizes Huntsman Advanced Materials' composite solutions for the automotive industry, including fast curing resin systems for body structures and leaf springs. It outlines various epoxy resin systems tailored for different composite manufacturing processes like wet compression molding, resin transfer molding, and a new dynamic fluid compression molding process. It also provides property data and descriptions of resin systems qualified for automotive wheel and preform production. Simulation tools are discussed which can optimize composite part design and manufacturing.
LOCTITE LB 8021 is a general purpose, low viscosity silicone oil used for lubricating metal and non-metal surfaces between -30°C and +150°C. It has a clear liquid appearance and 350 mPa·s viscosity. The product is a silicone oil dispersed in a propane/butane propellant and is used to lubricate parts like guides, conveyors and cutting knives. It is also suitable as a mold release agent and has approval for incidental food contact.
Huntsman Advanced Materials produces a range of thermosetting composite resin systems for various manufacturing industries. They offer technical support and expertise to help customers optimize processes and develop customized solutions. Their product range includes resin formulations for wet layup, resin transfer molding, infusion, filament winding, and other composites manufacturing methods. Huntsman works with customers to select the best resin system for their needs, improve quality and performance, and accelerate time to market.
These two products, Araldite® 1570 FST A/B and Epibond® 8000 FR A/B, are two-component epoxy structural adhesives designed for aerospace applications requiring flame, smoke and toxicity properties. Araldite® 1570 FST A/B is a semi-rigid adhesive with high elongation at break and long pot life at room temperature. Epibond® 8000 FR A/B is a rigid adhesive with high lap shear strength and accelerated cure at room temperature. Both adhesives meet FAR 25.853 requirements for flame, smoke and toxicity.
This safety data sheet provides information on LOCTITE 222 anaerobic adhesive. It lists the product identifier and supplier contact information. The product contains cumene hydroperoxide and other hazardous ingredients. It is classified as causing serious eye irritation and respiratory irritation. Exposure guidelines and personal protective equipment requirements are also outlined, including the need for gloves, safety glasses and adequate ventilation when handling the product.
This document provides technical information about AGILITYTM 1000 Performance LDPE, a high pressure low density polyethylene resin designed for faster blown film processing and higher output rates when blended with LLDPE resins. Some key characteristics include faster processing, maintaining bubble stability at higher rates, and excellent shrink properties. Physical and performance properties of films made from this resin are provided, as well as processing guidelines for blown film fabrication. Product stewardship and regulatory information is also included.
This technical data sheet provides information on Loctite 454, a cyanoacrylate adhesive. It is a one-part, thixotropic gel adhesive that cures rapidly with humidity. It can bond a variety of substrates including metals, plastics, elastomers, wood, leather, and fabrics. The gel consistency prevents run-off on vertical surfaces. Typical properties include a fixture time of less than one minute for many substrates and tensile strengths up to 15.1 MPa after curing for 72 hours. It also has good chemical and solvent resistance as well as heat resistance. Usage instructions and precautions are provided.
LOCTITE LB 8040 is a mineral oil formulation that can freeze and instantly crack rust at -43°C, allowing the oil to penetrate rust and lubricate seized metal parts. It sprays onto parts from a pressurized container. When sprayed onto rusted fasteners and allowed to react for 1-2 minutes, the frozen rust cracks and the oil penetrates to free seized parts while leaving them lubricated and protected from corrosion. The product comes in an amber-colored liquid with a density of 0.6 g/ml and viscosity below 5 mPa·s.
This technical data sheet provides information on Loctite 2701, a one-part anaerobic adhesive. It cures rapidly at room temperature when confined between close-fitting metal surfaces. The document includes typical properties of the uncured and cured adhesive. It also provides test results on performance characteristics like strength at different temperatures, with primers, and resistance to solvents. Guidelines are given for storage, directions of use, and limitations.
Techlube HD is a heavy duty water-based cable pulling lubricant designed for difficult cable installations. It provides superior friction reduction and adhesion to cables in wet conditions. Techlube HD is non-toxic, biodegradable, and suitable for electrical and power cables. It allows for regular pulling tension during installation and continues to lubricate even when ducts are flooded.
Techlube Multi is a water-based cable pulling lubricant that provides superior friction reduction for cable installation. It adheres well to cables in wet conditions and reduces the risk of cable damage during pulling. Techlube Multi is non-toxic, non-flammable, and biodegradable. It remains lubricating in flooded conditions and allows for additional cable installation in the same duct later.
Akfix HT300 is a high-performance silicone sealant developed for sealing and bonding applications requiring heat resistance up to 300°C. It is a one-component, acetoxy cure silicone that cures upon exposure to atmospheric moisture to form a tough, flexible, heat-resistant seal. The sealant is suitable for sealing and bonding in automotive and industrial applications involving high temperatures, such as ovens, stoves, heating systems, and more.
Techlube PHD is a water-based, pourable cable pulling lubricant that adheres well to cables in wet conditions. It is non-toxic, biodegradable, and suitable for use with electrical and telecommunication cables. Techlube PHD provides superior friction reduction during cable installation and allows for additional cables to be installed later in the same duct. It is recommended for underground cable installation and medium to lighter cable pulls. Techlube PHD is easy to apply by hand or machine and dries slowly to form a thin lubricating film on the cable.
This technical data sheet provides information about LOCTITE® C5-A® Copper Based Anti-Seize, which is a non-curing lubricant used to prevent seizing and galling between mating parts. It is a colloidal copper and petroleum grease that can be used in applications with an operating range of -29°C to 982°C. The data sheet includes typical properties like specific gravity, density, and flash point. It also provides directions for use and storage instructions.
Techlube FO is a water-based lubricant for pulling fiber optic cables and inner ducts underground. It adheres well to cables in wet conditions and reduces friction during pulls. Techlube FO is non-toxic, non-flammable, and biodegradable. It can be used to lubricate plastic conduits for installing communication and fiber optic cables, as well as for inner duct installations and duct pre-lubrication. Formulas are provided to calculate the amount of Techlube FO needed based on conduit length and diameter.
Loctite Hi-Tack Gasket Sealant is a red colored viscous liquid with a characteristic solvent odor which is a blend of elastomers and resins that is brushable and dries quickly to a highly tacky film. Temp. Range -65ºF to 500ºF
PASSIVE PURPLE is a Passivhaus/BBA certified liquid vapour control membrane that is spray or roller applied. It forms an airtight, flexible coating with excellent adhesion to surfaces like concrete, brick, and wood. Testing shows it has high vapour resistance, permeability to moisture vapour, and passes requirements for air tightness and fire resistance. The product sheet provides instructions for application and storage, as well as certifications and technical specifications.
Huntsman Advanced Materials provides materials for the wind turbine industry, including composites, adhesives, and repair solutions. They have over 20 years of experience partnering with wind turbine manufacturers to develop reliable and cost-effective materials. Their product portfolio includes resins, hardeners, and adhesives for various composite manufacturing processes and turbine component bonding and repair. Huntsman supports customers through technical expertise, custom product development, and helping optimize manufacturing processes.
This document provides information on ARALDITE 2011 A/B, a multi-purpose epoxy adhesive. It can bond various materials, including metal, ceramic, and wood. It has a long open time and cures over a wide range of temperatures. It provides good adhesion, insulation, and resistance to loads. The document provides details on applications, properties, testing results, curing and processing instructions, and storage guidelines.
Rando HD hydraulic fluids are designed to provide highly durable system protection and maximize equipment protection under severe conditions. They contain advanced additive technologies that deliver excellent anti-wear protection, thermal stability, and water separation. These fluids are suitable for demanding applications and are approved and recommended by major hydraulic system manufacturers. Rando HD helps extend asset life by protecting against oxidation, corrosion, and thermal degradation even in high-speed, high-temperature operations.
Techlube M is a water-based cable pulling lubricant with microspheres that provides superior friction reduction between cables and conduits. It strongly adheres to cables in wet conditions and is not readily washed off. Techlube M is non-flammable, non-toxic, and requires lower quantities per cable pull than other lubricants. It is designed for underground telecommunication and CATV cable installations.
Hardcastle Petrofer is a leading manufacturer and supplier of Quenching Oils. These are preferred for use in induction/flame hardening and tank quenching applications for various grades of steel, castings as well as for solution treatment of distortion-prone aluminum sheet for aerospace and components of automotive applications. Visit the website to know more!
Quenching Oils - Manufacturer & Supplier in India | Hardcastle Petroferrohankumar445
Hardcastle Petrofer is India's leading manufacturer & supplier of Quenching oils product. It is used for alloy steels, fasteners, carburized parts with good evaporation stability, suitable for use in open and sealed quench furnaces. Contact us to know more!
Quenching Oils - Manufacturer & Supplier in India | Hardcastle Petroferrohankumar445
This document provides information on quenching oils and processes from Hardcastle Petrofer Private Limited. It discusses the quenching process which involves three phases: a vapor blanket phase, boiling phase, and convection phase. The duration of the vapor blanket phase is important for achieving the desired metallurgical properties. The document also covers factors that influence quenching such as bath temperature, ageing resistance, and consumption of quenching oils. A variety of quenching oils are described including medium speed, medium fast, fast, and marquenching oils for different applications.
A leading manufacturer and supplier of Quenching Oils in India | Hardcastle P...rohankumar445
Hardcastle Petrofer is India's leading manufacturer & supplier of Quenching oils product. It is used for alloy steels, fasteners, carburized parts with good evaporation stability, suitable for use in open and sealed quench furnaces. Contact us to know more!
Similar to Loctite 420 instant adhesive, 20 g (20)
They take pride in working with renowned companies like THREEBOND, Epoxy Resin Putty, BIRKOSIT, BELZONA, KOLOR KUT,LOCTITE, DEVCON, FERRO CORDOBOND, WEICON, MOLYKOTE, Hypoxy, Somafix and many more. They have a team of professionals who work day and night to find the finest products for their clients. Technical Beacons work tirelessly burning the midnight oil each day in order to provide the best quality products at economical prices to their clients.
Are you looking for Permatex High-Temp Red RTV Silicone Gasket Maker? We are one of the best industrial chemical product suppliers. For best result clean and dry all surfaces with s residue-free. You can use it for cleaning uncured silicone from hands, tools and clothing with Fast Orange® Hand Cleaner.
MOLYSLIP MCC compound has been developed as a highly efficient lubricant for metalworkingoperations. It is particularly effective with more difficult metals and alloys such as titanium, stainless steel and nimonics.
AKFIX C920 EASF CHEMICAL ANCHOR (STYRENE FREE),354 MLTechnicalbeacon
Akfix C920 is a styrene-free, epoxy acrylate injection mortar that cures quickly. It can be used to anchor rods, bars, profiles and other elements in concrete, stone, hollow bricks, and cavity blocks. The mortar is thixotropic, allowing for vertical and horizontal application. It provides strong anchoring for a variety of heavy and medium load applications, including attaching wood, metal, sanitary fittings and other construction elements. The product comes in 345ml or 400ml cartridges for use with a caulking gun and has a working time of 2-45 minutes depending on temperature.
This disposable particulate respirator is find for strong which include the ones from processing minerals, coal, iron ore, flour and certain substances. It is also recommended to use for liquid or non-oil based sprays that don't emit harmful vapors.
For 45 years now, the brand Tangit - offering products for the plumbing industry - has been a synonym of quality, cost effectiveness and ease of application.
This technical datasheet provides information on WEICON Allround Sealing Spray, including its composition, features, shelf life, temperature resistance, processing instructions, storage requirements, and safety considerations. The spray seals leaks reliably and quickly for indoor and outdoor use on surfaces like stone, metal, plastic, wood, and more. It is overpaintable after 20 minutes, cures within 2-4 hours, and is available in 400ml cans in white, black, or grey.
Particles such as those from grinding, sanding,
sweeping, sawing, bagging, or processing
minerals, coal, iron ore, flour, metal, wood,
pollen, and certain other substances. Liquid or
non-oil based particles from sprays that do not
also emit oil aerosols or vapors. For additional
information on 3M use recommendations for
this class of respirator please consult the 3M
Respirator Selection Guide found on the 3M
OH&ESD web site at www.3M.com/occsafety
or call 1-800-243-4630 in U.S.A. In Canada
call 1 800 267-4414.
[To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
This presentation is a curated compilation of PowerPoint diagrams and templates designed to illustrate 20 different digital transformation frameworks and models. These frameworks are based on recent industry trends and best practices, ensuring that the content remains relevant and up-to-date.
Key highlights include Microsoft's Digital Transformation Framework, which focuses on driving innovation and efficiency, and McKinsey's Ten Guiding Principles, which provide strategic insights for successful digital transformation. Additionally, Forrester's framework emphasizes enhancing customer experiences and modernizing IT infrastructure, while IDC's MaturityScape helps assess and develop organizational digital maturity. MIT's framework explores cutting-edge strategies for achieving digital success.
These materials are perfect for enhancing your business or classroom presentations, offering visual aids to supplement your insights. Please note that while comprehensive, these slides are intended as supplementary resources and may not be complete for standalone instructional purposes.
Frameworks/Models included:
Microsoft’s Digital Transformation Framework
McKinsey’s Ten Guiding Principles of Digital Transformation
Forrester’s Digital Transformation Framework
IDC’s Digital Transformation MaturityScape
MIT’s Digital Transformation Framework
Gartner’s Digital Transformation Framework
Accenture’s Digital Strategy & Enterprise Frameworks
Deloitte’s Digital Industrial Transformation Framework
Capgemini’s Digital Transformation Framework
PwC’s Digital Transformation Framework
Cisco’s Digital Transformation Framework
Cognizant’s Digital Transformation Framework
DXC Technology’s Digital Transformation Framework
The BCG Strategy Palette
McKinsey’s Digital Transformation Framework
Digital Transformation Compass
Four Levels of Digital Maturity
Design Thinking Framework
Business Model Canvas
Customer Journey Map
Event Report - SAP Sapphire 2024 Orlando - lots of innovation and old challengesHolger Mueller
Holger Mueller of Constellation Research shares his key takeaways from SAP's Sapphire confernece, held in Orlando, June 3rd till 5th 2024, in the Orange Convention Center.
Zodiac Signs and Food Preferences_ What Your Sign Says About Your Tastemy Pandit
Know what your zodiac sign says about your taste in food! Explore how the 12 zodiac signs influence your culinary preferences with insights from MyPandit. Dive into astrology and flavors!
Navigating the world of forex trading can be challenging, especially for beginners. To help you make an informed decision, we have comprehensively compared the best forex brokers in India for 2024. This article, reviewed by Top Forex Brokers Review, will cover featured award winners, the best forex brokers, featured offers, the best copy trading platforms, the best forex brokers for beginners, the best MetaTrader brokers, and recently updated reviews. We will focus on FP Markets, Black Bull, EightCap, IC Markets, and Octa.
Structural Design Process: Step-by-Step Guide for BuildingsChandresh Chudasama
The structural design process is explained: Follow our step-by-step guide to understand building design intricacies and ensure structural integrity. Learn how to build wonderful buildings with the help of our detailed information. Learn how to create structures with durability and reliability and also gain insights on ways of managing structures.
How MJ Global Leads the Packaging Industry.pdfMJ Global
MJ Global's success in staying ahead of the curve in the packaging industry is a testament to its dedication to innovation, sustainability, and customer-centricity. By embracing technological advancements, leading in eco-friendly solutions, collaborating with industry leaders, and adapting to evolving consumer preferences, MJ Global continues to set new standards in the packaging sector.
How to Implement a Strategy: Transform Your Strategy with BSC Designer's Comp...Aleksey Savkin
The Strategy Implementation System offers a structured approach to translating stakeholder needs into actionable strategies using high-level and low-level scorecards. It involves stakeholder analysis, strategy decomposition, adoption of strategic frameworks like Balanced Scorecard or OKR, and alignment of goals, initiatives, and KPIs.
Key Components:
- Stakeholder Analysis
- Strategy Decomposition
- Adoption of Business Frameworks
- Goal Setting
- Initiatives and Action Plans
- KPIs and Performance Metrics
- Learning and Adaptation
- Alignment and Cascading of Scorecards
Benefits:
- Systematic strategy formulation and execution.
- Framework flexibility and automation.
- Enhanced alignment and strategic focus across the organization.
Digital Marketing with a Focus on Sustainabilitysssourabhsharma
Digital Marketing best practices including influencer marketing, content creators, and omnichannel marketing for Sustainable Brands at the Sustainable Cosmetics Summit 2024 in New York
HOW TO START UP A COMPANY A STEP-BY-STEP GUIDE.pdf46adnanshahzad
How to Start Up a Company: A Step-by-Step Guide Starting a company is an exciting adventure that combines creativity, strategy, and hard work. It can seem overwhelming at first, but with the right guidance, anyone can transform a great idea into a successful business. Let's dive into how to start up a company, from the initial spark of an idea to securing funding and launching your startup.
Introduction
Have you ever dreamed of turning your innovative idea into a thriving business? Starting a company involves numerous steps and decisions, but don't worry—we're here to help. Whether you're exploring how to start a startup company or wondering how to start up a small business, this guide will walk you through the process, step by step.
Storytelling is an incredibly valuable tool to share data and information. To get the most impact from stories there are a number of key ingredients. These are based on science and human nature. Using these elements in a story you can deliver information impactfully, ensure action and drive change.
IMPACT Silver is a pure silver zinc producer with over $260 million in revenue since 2008 and a large 100% owned 210km Mexico land package - 2024 catalysts includes new 14% grade zinc Plomosas mine and 20,000m of fully funded exploration drilling.
3 Simple Steps To Buy Verified Payoneer Account In 2024SEOSMMEARTH
Buy Verified Payoneer Account: Quick and Secure Way to Receive Payments
Buy Verified Payoneer Account With 100% secure documents, [ USA, UK, CA ]. Are you looking for a reliable and safe way to receive payments online? Then you need buy verified Payoneer account ! Payoneer is a global payment platform that allows businesses and individuals to send and receive money in over 200 countries.
If You Want To More Information just Contact Now:
Skype: SEOSMMEARTH
Telegram: @seosmmearth
Gmail: seosmmearth@gmail.com
At Techbox Square, in Singapore, we're not just creative web designers and developers, we're the driving force behind your brand identity. Contact us today.
1. Technical Data Sheet
LOCTITE®
420™
January-2010
PRODUCT DESCRIPTION
LOCTITE®
420™ provides the following product
characteristics:
Technology Cyanoacrylate
Chemical Type Ethyl cyanoacrylate
Appearance (uncured) Transparent, colorless to straw
colored liquidLMS
Components One part - requires no mixing
Viscosity Very low
Cure Humidity
Application Bonding
Key Substrates Plastics, Rubbers and Metals
LOCTITE®
420™ is a general purpose cyanoacrylate instant
adhesive.
Mil-A-46050C
LOCTITE®
420™ is tested to the lot requirements of Military
Specification Mil-A-46050C. Note: This is a regional approval.
Please contact your local Technical Service Center for more
information and clarification.
Commercial Item Description A-A-3097:
LOCTITE®
420™ has been qualified to Commercial Item
Description A-A-3097. Note: This is a regional approval.
Please contact your local Technical Service Center for more
information and clarification.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Specific Gravity @ 25 °C 1.05
Viscosity, Cone & Plate, mPa·s (cP):
Temperature: 25 °C, Shear Rate: 3,000 s-1
1 to 4LMS
Viscosity, Brookfield - LVF, 25 °C, mPa·s (cP):
Spindle 1, speed 60 rpm, 1 to 5
Vapour Pressure, hPa <1
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Under normal conditions, the atmospheric moisture initiates the
curing process. Although full functional strength is developed
in a relatively short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed.
Cure Speed vs. Substrate
The rate of cure will depend on the substrate used. The table
below shows the fixture time achieved on different materials
at 22 °C / 50 % relative humidity. This is defined as the time to
develop a shear strength of 0.1 N/mm².
Fixture Time, seconds:
Mild Steel (degreased) 10 to 30
Aluminum (degreased) 5 to 15
Zinc dichromate 30 to 90
Neoprene <5
Rubber, nitrile <5
ABS 10 to 30
PVC 3 to 10
Polycarbonate 20 to 60
Phenolic 5 to 20
Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure.
Cure Speed vs. Humidity
The rate of cure will depend on the ambient relative humidity.
The following graph shows the tensile strength developed with
time on Buna N rubber at different levels of humidity.
%FullCuredStrength@22°C
Cure Time, seconds
100
75
50
25
0
0 10 20 30 40 50 60
60% RH
40% RH
20% RH
Cure Speed vs. Activator
Where cure speed is unacceptably long due to large gaps,
applying activator to the surface will improve cure speed.
However, this can reduce ultimate strength of the bond and
therefore testing is recommended to confirm effect.
2. TDS LOCTITE®
420™, January-2010
TYPICAL PROPERTIES OF CURED MATERIAL
After 24 hours @ 22 °C
Physical Properties:
Coefficient of Thermal Expansion,
ISO 11359-2, K-1
100×10-6
Coefficient of Thermal Conductivity, ISO 8302,
W/(m·K)
0.1
Softening Point, DIN EN 1427, °C 165
Electrical Properties:
Dielectric Constant / Dissipation Factor, IEC 60250:
0.1-kHz 2 to 3.3 / <0.02
1-kHz 2 to 3.5 / <0.02
10-kHz 2 to 3.5 / <0.02
Volume Resistivity, IEC 60093, Ω·cm 2×1015
to 10×1015
Surface Resistivity, IEC 60093, Ω 10×1015
to 80×1015
Dielectric Breakdown Strength,
IEC 60243-1, kV/mm
25
TYPICAL PERFORMANCE OF CURED MATERIAL
Adhesive Properties
After 24 hours @ 22 °C
Lap Shear Strength, ISO 4587:
Steel (grit blasted) N/mm² 15 to 26
(psi) (2,175 to 3,770)
Aluminum (grit blasted) N/mm² 12 to 19
(psi) (1,740 to 2,755)
Zinc dichromate N/mm² 6 to 13
(psi) (870 to 1,885)
ABS N/mm² 6 to 20
(psi) (870 to 2,900)
PVC N/mm² 6 to 20
(psi) (870 to 2,900)
Polycarbonate N/mm² 6 to 20
(psi) (870 to 2,900)
Phenolic N/mm² 5 to 20
(psi) (725 to 2,900)
Neoprene N/mm² 5 to 15
(psi) (725 to 2,175)
Nitrile N/mm² 5 to 15
(psi) (725 to 2,175)
Tensile Strength, ISO 6922:
Steel N/mm² 12 to 25
(psi) (1,740 to 3,625)
Buna-N N/mm² 5 to 15
(psi) (725 to 2,175)
"T" Peel Strength, ISO 11339:
Steel (degreased) N/mm <0.5
(lb/in) (<2.8)
After 10 seconds @ 22 °C
Tensile Strength, ISO 6922:
Buna-N N/mm² ≥6.0LMS
(psi) (≥870)
TYPICAL ENVIRONMENTAL RESISTANCE
Cured for 1 week @ 22 °C
Lap Shear Strength, ISO 4587:
Mild Steel (grit blasted)
Hot Strength
Tested at temperature
%Strength@22°C
Temperature, °C
100
75
50
25
0
-50 0 50 100 150
Heat Aging
Aged at temperature indicated and tested @ 22 °C
%InitialStrength@22°C
Exposure Time, hours
100
75
50
25
0
0 1000 2000 3000 4000 5000
60°C
80°C
100°C
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
% of initial strength
Environment °C 100 h 500 h 1000 h
Motor oil (MIL-L-46152) 40 100 100 95
Gasoline 22 100 100 100
Isopropanol 22 100 100 100
Ethanol 22 100 100 100
Freon TA 22 100 100 100
1,1,1 Trichloroethane 22 100 100 100
Heat/humidity 95% RH 40 80 75 65
Heat/humidity 95% RH
on polycarbonate
40 100 100 100
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Directions for use:
1. For best performance bond surfaces should be clean and
free from grease.
2. This product performs best in thin bond gaps (0.05 mm).
3. Excess adhesive can be dissolved with Loctite cleanup
solvents, nitromethane or acetone.
Henkel Americas
+860.571.5100
Henkel Europe
+49.89.320800.1800
Henkel Asia Pacific
+86.21.2891.8859
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
3. TDS LOCTITE®
420™, January-2010
Loctite Material SpecificationLMS
LMS dated August-29, 2003. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or
greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note:
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. The product can have a variety of different applications as well as
differing application and working conditions in your environment that
are beyond our control. Henkel is, therefore, not liable for the suitability
of our product for the production processes and conditions in respect
of which you use them, as well as the intended applications and
results. We strongly recommend that you carry out your own prior trials
to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
In case products are delivered by Henkel Belgium NV, Henkel
Electronic Materials NV, Henkel Nederland BV, Henkel
Technologies France SAS and Henkel France SA please
additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal
ground, Henkel’s liability will in no event exceed the amount of the
concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the
following disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. Henkel is, therefore, not liable for the suitability of our product for
the production processes and conditions in respect of which you use
them, as well as the intended applications and results. We strongly
recommend that you carry out your own prior trials to confirm such
suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
In case products are delivered by Henkel Corporation, Resin
Technology Group, Inc., or Henkel Canada Corporation, the
following disclaimer is applicable:
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the results
obtained by others over whose methods we have no control. It is the
user's responsibility to determine suitability for the user's purpose of
any production methods mentioned herein and to adopt such
precautions as may be advisable for the protection of property and of
persons against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular purpose,
arising from sale or use of Henkel Corporation’s products. Henkel
Corporation specifically disclaims any liability for consequential
or incidental damages of any kind, including lost profits. The
discussion herein of various processes or compositions is not to be
interpreted as representation that they are free from domination of
patents owned by others or as a license under any Henkel Corporation
patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application
before repetitive use, using this data as a guide. This product may be
covered by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.
Reference 1.2
Henkel Americas
+860.571.5100
Henkel Europe
+49.89.320800.1800
Henkel Asia Pacific
+86.21.2891.8859
For the most direct access to local sales and technical support visit: www.henkel.com/industrial