1. The document provides instructions for removing and installing starting motors, alternators, fuel injection pumps, nozzle holders, and water pumps on various PC27-45MRX excavator models.
2. Key steps include disconnecting battery cables, removing covers and brackets, disconnecting electrical connectors and fluid lines, and loosening and removing mounting hardware.
3. Reinstallation is done in the reverse order, taking care to align parts and tighten fasteners to the specified torques.
Komatsu pc27 mrx 1 excavator service repair manual sn11574 and upfjjskekdm
- The document provides instructions for removing and installing various starting motor, alternator, fuel injection pump, nozzle holder, water pump, thermostat, engine front seal, and engine rear seal components on Komatsu PC27-45MRX excavators.
- The removal instructions involve disconnecting electrical connectors and hoses, loosening mounting bolts, and using pullers as needed to separate components. Installation is the reverse of removal.
- Technicians are advised to note matching marks, tighten bolts to the specified torque, and refill coolant as needed when reinstalling components.
This document provides instructions for how to use the service manual. It begins with an introduction on how the manual is organized with sections, indexes, descriptions, and procedures. It explains that procedures are step-by-step with illustrations and specifications in bold. It provides guidance on tools, repairs, precautions and abbreviations used. Safety warnings are highlighted regarding working on vehicles with airbags and catalytic converters.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)ufjjdjkkskemmd
This document provides instructions for removing and installing various engine components on a Komatsu PW160-7K wheel loader, including the governor motor assembly, starting motor assembly, fuel injection pump assembly, engine front seal, and engine rear seal. The summary highlights the key steps:
1. Disconnect negative battery terminal before removing components.
2. For governor motor removal, disconnect rod and electrical connectors and remove three securing bolts. Installation is the reverse.
3. For starting motor removal, disconnect two wires and remove two mounting bolts. Installation is the reverse.
4. For fuel injection pump removal, disconnect linkages, remove access cap and retaining nut, and pull pump gear loose
This document provides instructions for servicing a manual transaxle. It describes removing old packing material from sealing surfaces and cleaning components. It also outlines the transaxle types, gear engagements, preparation steps like using special service tools, and removal and installation of the transaxle and various components. Troubleshooting tips are provided in a table listing potential issues and likely causes.
This document provides step-by-step instructions for disassembling and assembling a CLAAS CERES 316 326 336 346 2+4WD tractor engine. It outlines 57 steps to fully disassemble the engine, removing components like the fan, pulleys, pumps, heads, crankshaft and more. Reassembly is described briefly, noting to clean parts and replace seals and gaskets, and torque all nuts and bolts to the specified values. Specific attention is paid to mounting the balancing device counter-rotating weight and installing the tappets, drive shaft, main bearing caps and thrust rings.
Claas arion 550 510 hexashift (a74) tractor service repair manual serial no. ...dufjsfjkskekem
This repair manual provides instructions for repairing the engine flywheel housing and sump of ARION tractors. It gives specifications for components and tightening torques for bolts. The document describes removing and installing the engine flywheel housing and sump, which requires draining fluids, removing surrounding parts, and using lifting equipment due to the heavy weight of parts. Safety warnings are provided to take precautions when lifting heavy components.
Claas arion 660 510 cmatic (type a77) tractor service repair manual serial no...fusjejfjskeksmem
This document provides instructions for removing the complete engine from ARION 600 A77 and ARION 500 A75 tractors. The key steps include: draining fluids, removing bonnet and tank, disconnecting exhaust components, drive shafts and couplings, lowering the front axle (if suspended), and using trolleys to uncouple the engine from the transmission. Special tools are required to aid the process, which involves undoing numerous bolts and disconnecting wiring harnesses and hydraulic lines. Safety warnings are also provided regarding lifting heavy components.
This repair manual provides instructions for removing and installing the timing cover on AXION 800 tractors. Key steps include draining fluids, removing engine components to access the cover, cleaning and applying sealant to the mating surfaces, installing the new cover and related components, and tightening fasteners to the specified torques. Safety warnings are provided regarding lifting heavy parts and handling hazardous materials.
Komatsu pc27 mrx 1 excavator service repair manual sn11574 and upfjjskekdm
- The document provides instructions for removing and installing various starting motor, alternator, fuel injection pump, nozzle holder, water pump, thermostat, engine front seal, and engine rear seal components on Komatsu PC27-45MRX excavators.
- The removal instructions involve disconnecting electrical connectors and hoses, loosening mounting bolts, and using pullers as needed to separate components. Installation is the reverse of removal.
- Technicians are advised to note matching marks, tighten bolts to the specified torque, and refill coolant as needed when reinstalling components.
This document provides instructions for how to use the service manual. It begins with an introduction on how the manual is organized with sections, indexes, descriptions, and procedures. It explains that procedures are step-by-step with illustrations and specifications in bold. It provides guidance on tools, repairs, precautions and abbreviations used. Safety warnings are highlighted regarding working on vehicles with airbags and catalytic converters.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)ufjjdjkkskemmd
This document provides instructions for removing and installing various engine components on a Komatsu PW160-7K wheel loader, including the governor motor assembly, starting motor assembly, fuel injection pump assembly, engine front seal, and engine rear seal. The summary highlights the key steps:
1. Disconnect negative battery terminal before removing components.
2. For governor motor removal, disconnect rod and electrical connectors and remove three securing bolts. Installation is the reverse.
3. For starting motor removal, disconnect two wires and remove two mounting bolts. Installation is the reverse.
4. For fuel injection pump removal, disconnect linkages, remove access cap and retaining nut, and pull pump gear loose
This document provides instructions for servicing a manual transaxle. It describes removing old packing material from sealing surfaces and cleaning components. It also outlines the transaxle types, gear engagements, preparation steps like using special service tools, and removal and installation of the transaxle and various components. Troubleshooting tips are provided in a table listing potential issues and likely causes.
This document provides step-by-step instructions for disassembling and assembling a CLAAS CERES 316 326 336 346 2+4WD tractor engine. It outlines 57 steps to fully disassemble the engine, removing components like the fan, pulleys, pumps, heads, crankshaft and more. Reassembly is described briefly, noting to clean parts and replace seals and gaskets, and torque all nuts and bolts to the specified values. Specific attention is paid to mounting the balancing device counter-rotating weight and installing the tappets, drive shaft, main bearing caps and thrust rings.
Claas arion 550 510 hexashift (a74) tractor service repair manual serial no. ...dufjsfjkskekem
This repair manual provides instructions for repairing the engine flywheel housing and sump of ARION tractors. It gives specifications for components and tightening torques for bolts. The document describes removing and installing the engine flywheel housing and sump, which requires draining fluids, removing surrounding parts, and using lifting equipment due to the heavy weight of parts. Safety warnings are provided to take precautions when lifting heavy components.
Claas arion 660 510 cmatic (type a77) tractor service repair manual serial no...fusjejfjskeksmem
This document provides instructions for removing the complete engine from ARION 600 A77 and ARION 500 A75 tractors. The key steps include: draining fluids, removing bonnet and tank, disconnecting exhaust components, drive shafts and couplings, lowering the front axle (if suspended), and using trolleys to uncouple the engine from the transmission. Special tools are required to aid the process, which involves undoing numerous bolts and disconnecting wiring harnesses and hydraulic lines. Safety warnings are also provided regarding lifting heavy components.
This repair manual provides instructions for removing and installing the timing cover on AXION 800 tractors. Key steps include draining fluids, removing engine components to access the cover, cleaning and applying sealant to the mating surfaces, installing the new cover and related components, and tightening fasteners to the specified torques. Safety warnings are provided regarding lifting heavy parts and handling hazardous materials.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fujsjefjskkem
This document provides instructions for removing and installing various components of a Komatsu PW160-7K engine, including the cylinder head assembly. The multi-step removal process involves draining fluids, disconnecting electrical connections and hoses, and removing components like the cooling fan, alternator, and turbocharger. Installation is generally the reverse of removal, with specific torque specifications provided. Special tools are listed for pulling components like the nozzle holder assemblies.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fjjskdmnenemm
This document provides instructions for removing and installing various components of a Komatsu PW160-7K engine, including the cylinder head assembly. The multi-step removal process involves draining fluids, disconnecting electrical connections and hoses, and removing components like the cooling fan, alternator, and turbocharger. Installation is generally the reverse of removal. Special tools are required for some components, and torque specifications are provided.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)dfujsjefjkskemm
This document provides instructions for removing and installing various engine components on a Komatsu PW160-7K wheel loader, including the governor motor assembly, starting motor assembly, fuel injection pump assembly, engine front seal, and engine rear seal. The summary highlights the key steps:
1. Disconnect negative battery terminal before removing components.
2. For governor motor removal, disconnect rod and electrical connectors and remove three securing bolts. Installation is the reverse.
3. For starting motor removal, disconnect two wires and remove two mounting bolts. Installation is the reverse.
4. For fuel injection pump removal, disconnect linkages, remove access cap and retaining nut, and pull pump gear loose
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fjjsekmsmmes
This document provides instructions for removing and installing the cylinder head assembly of a Komatsu PW160-7K excavator. The key steps include draining coolant, disconnecting various hoses and electrical connections, removing the air conditioning compressor, fuel filter, exhaust manifold, alternator and other components to access the cylinder head. The nozzle holder assemblies and rocker arm assemblies are then removed to allow lifting off the cylinder head. Reinstallation follows the reverse order.
Hyundai 20DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect and replace components as needed and apply grease before reassembling using the reverse order of disassembly. Safety precautions are noted such as using plastic hammers to avoid damage and heating bearings for proper installation.
Hyundai 33DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect and replace components as needed and apply grease before reassembling using the reverse order of disassembly. Safety precautions are noted such as using plastic hammers to avoid damage and heating bearings for proper installation.
Hyundai 25DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect, replace seals and bearings, and reinstall components in the proper order. Heating bearings during assembly is noted. Safety precautions are included to avoid damage to parts.
Hyundai 30DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of a transmission. It includes:
1. Disassembly of the transmission into individual components and gear assemblies.
2. Disassembly of the gear assemblies into sub-components.
3. Assembly of the gear assemblies and transmission, reversing the disassembly steps. Precautions are provided to avoid damage and properly apply sealants and fasteners.
Hyundai 35DF-7 Forklift Truck Service Repair Manual.pdfudjkskmdmdm
1. This section details the disassembly and assembly of the transmission system. It includes disassembling the transmission, gear assemblies, and individual components.
2. The disassembly process involves draining fluid, removing external components, and then separating internal gear and clutch assemblies.
3. The assembly process reverses the disassembly steps and provides instructions on cleaning, inspecting, applying sealants, and tightening components in the correct order and with specified torques.
This document provides instructions for servicing a manual transaxle. It describes removing old packing material from sealing surfaces and cleaning components. It also outlines the transaxle types, gear engagements, preparation steps like using special service tools, and removal and installation of the transaxle and various components. Troubleshooting tips are provided in a table listing potential issues and likely causes.
John deere 92 h riding lawn tractor service repair technical manual (tm113419)fjskekertkskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, including reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms, and push rods before removing the head and gasket.
John deere x135 r riding lawn tractor service repair technical manual (tm113419)fjsekksemfmm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing the cylinder head requires taking off the valve cover, rocker arms, push rods and then loosening the head bolts in a specific sequence. Reinstallation torques all components.
John deere x115 r riding lawn tractor service repair technical manual (tm113419)fujskekskemm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fujskekskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms and push rods before removing the head and gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fjkseksmefmm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fjjsfkskemem
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 80 l tractor service repair...fjekkdmmem
This document provides part numbers and descriptions for engine components of a McCormick RT30 tractor. It lists 46 individual parts for the engine, including cylinders, pistons, gears, shafts, plates and other internal components. Each part is identified by a reference number, description, and whether it is for the engine (T-A) or transmission (T-B). It also specifies components that are part of assemblies and not individually serviced.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 75 l tractor service repair...fjekkdmmem
This document provides component part listings and information for an engine. It includes over 80 individual part listings with details like part numbers, replacement kits, and torque specifications. The parts are for components of the engine like the cylinder block, crankshaft, pistons, rods, head, valves, rockers, and various fasteners. It also provides the engine model and serial number range the parts correspond to.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 60 l tractor service repair...fjekkdmmem
This document contains information about engine components for a Perkins engine, including identification numbers, part names and numbers, quantities, and repair kit information. It lists 40 line items describing individual engine parts and components such as cylinders, bearings, gears, plates, seals, and other items, along with specifications like torque settings. Additional information provided includes manufacturer and model details and notes on replacement parts.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c80l tractor service repair...fjekkdmmem
This document provides component part listings and information for engines. It includes listings of parts with identification numbers, part names, quantities and other technical specifications. For example, it lists a Perkins engine with a 54.5 kw output, and it provides listings of cylinder blocks, gears, pistons and other engine parts along with identifying information for each. It contains detailed technical specifications and part numbers for replacement components.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c75l tractor service repair...fjekkdmmem
This document provides component part listings and information for the repair and replacement of parts for a Perkins XL75075 engine. It includes over 40 individual part listings with details like part numbers, component names, replacement part kits, and specifications. The parts cover various engine systems like the cylinder block, crankshaft, cylinder head, camshaft, and fuel system.
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 80 tractor service repair m...fjekkdmmem
This document provides a list of components for an engine, including identification numbers, names, and other details. It lists items like cylinders, bearings, plugs, gears, plates, and other engine parts. Quantities and part numbers are provided for each component. Notes indicate some items are only to be ordered as replacements and provide color coding for identifying similar parts.
More Related Content
Similar to Komatsu pc40 mrx 1 excavator service repair manual sn1001 and up
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fujsjefjskkem
This document provides instructions for removing and installing various components of a Komatsu PW160-7K engine, including the cylinder head assembly. The multi-step removal process involves draining fluids, disconnecting electrical connections and hoses, and removing components like the cooling fan, alternator, and turbocharger. Installation is generally the reverse of removal, with specific torque specifications provided. Special tools are listed for pulling components like the nozzle holder assemblies.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fjjskdmnenemm
This document provides instructions for removing and installing various components of a Komatsu PW160-7K engine, including the cylinder head assembly. The multi-step removal process involves draining fluids, disconnecting electrical connections and hoses, and removing components like the cooling fan, alternator, and turbocharger. Installation is generally the reverse of removal. Special tools are required for some components, and torque specifications are provided.
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)dfujsjefjkskemm
This document provides instructions for removing and installing various engine components on a Komatsu PW160-7K wheel loader, including the governor motor assembly, starting motor assembly, fuel injection pump assembly, engine front seal, and engine rear seal. The summary highlights the key steps:
1. Disconnect negative battery terminal before removing components.
2. For governor motor removal, disconnect rod and electrical connectors and remove three securing bolts. Installation is the reverse.
3. For starting motor removal, disconnect two wires and remove two mounting bolts. Installation is the reverse.
4. For fuel injection pump removal, disconnect linkages, remove access cap and retaining nut, and pull pump gear loose
Komatsu pw160 7 k hydraulic excavator service repair manual (sn k40001 and up)fjjsekmsmmes
This document provides instructions for removing and installing the cylinder head assembly of a Komatsu PW160-7K excavator. The key steps include draining coolant, disconnecting various hoses and electrical connections, removing the air conditioning compressor, fuel filter, exhaust manifold, alternator and other components to access the cylinder head. The nozzle holder assemblies and rocker arm assemblies are then removed to allow lifting off the cylinder head. Reinstallation follows the reverse order.
Hyundai 20DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect and replace components as needed and apply grease before reassembling using the reverse order of disassembly. Safety precautions are noted such as using plastic hammers to avoid damage and heating bearings for proper installation.
Hyundai 33DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect and replace components as needed and apply grease before reassembling using the reverse order of disassembly. Safety precautions are noted such as using plastic hammers to avoid damage and heating bearings for proper installation.
Hyundai 25DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of transmission components. It describes removing the transmission oil, torque converter, pump sub assembly, control valve assembly, gears, housing and other parts. The process is reversed for assembly, with instructions to clean, inspect, replace seals and bearings, and reinstall components in the proper order. Heating bearings during assembly is noted. Safety precautions are included to avoid damage to parts.
Hyundai 30DF-7T Forklift Truck Service Repair Manual.pdfudjkskmdmdm
This document provides instructions for disassembly and assembly of a transmission. It includes:
1. Disassembly of the transmission into individual components and gear assemblies.
2. Disassembly of the gear assemblies into sub-components.
3. Assembly of the gear assemblies and transmission, reversing the disassembly steps. Precautions are provided to avoid damage and properly apply sealants and fasteners.
Hyundai 35DF-7 Forklift Truck Service Repair Manual.pdfudjkskmdmdm
1. This section details the disassembly and assembly of the transmission system. It includes disassembling the transmission, gear assemblies, and individual components.
2. The disassembly process involves draining fluid, removing external components, and then separating internal gear and clutch assemblies.
3. The assembly process reverses the disassembly steps and provides instructions on cleaning, inspecting, applying sealants, and tightening components in the correct order and with specified torques.
This document provides instructions for servicing a manual transaxle. It describes removing old packing material from sealing surfaces and cleaning components. It also outlines the transaxle types, gear engagements, preparation steps like using special service tools, and removal and installation of the transaxle and various components. Troubleshooting tips are provided in a table listing potential issues and likely causes.
John deere 92 h riding lawn tractor service repair technical manual (tm113419)fjskekertkskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, including reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms, and push rods before removing the head and gasket.
John deere x135 r riding lawn tractor service repair technical manual (tm113419)fjsekksemfmm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing the cylinder head requires taking off the valve cover, rocker arms, push rods and then loosening the head bolts in a specific sequence. Reinstallation torques all components.
John deere x115 r riding lawn tractor service repair technical manual (tm113419)fujskekskemm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fujskekskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms and push rods before removing the head and gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fjkseksmefmm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fjjsfkskemem
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
Similar to Komatsu pc40 mrx 1 excavator service repair manual sn1001 and up (16)
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 80 l tractor service repair...fjekkdmmem
This document provides part numbers and descriptions for engine components of a McCormick RT30 tractor. It lists 46 individual parts for the engine, including cylinders, pistons, gears, shafts, plates and other internal components. Each part is identified by a reference number, description, and whether it is for the engine (T-A) or transmission (T-B). It also specifies components that are part of assemblies and not individually serviced.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 75 l tractor service repair...fjekkdmmem
This document provides component part listings and information for an engine. It includes over 80 individual part listings with details like part numbers, replacement kits, and torque specifications. The parts are for components of the engine like the cylinder block, crankshaft, pistons, rods, head, valves, rockers, and various fasteners. It also provides the engine model and serial number range the parts correspond to.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 60 l tractor service repair...fjekkdmmem
This document contains information about engine components for a Perkins engine, including identification numbers, part names and numbers, quantities, and repair kit information. It lists 40 line items describing individual engine parts and components such as cylinders, bearings, gears, plates, seals, and other items, along with specifications like torque settings. Additional information provided includes manufacturer and model details and notes on replacement parts.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c80l tractor service repair...fjekkdmmem
This document provides component part listings and information for engines. It includes listings of parts with identification numbers, part names, quantities and other technical specifications. For example, it lists a Perkins engine with a 54.5 kw output, and it provides listings of cylinder blocks, gears, pistons and other engine parts along with identifying information for each. It contains detailed technical specifications and part numbers for replacement components.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c75l tractor service repair...fjekkdmmem
This document provides component part listings and information for the repair and replacement of parts for a Perkins XL75075 engine. It includes over 40 individual part listings with details like part numbers, component names, replacement part kits, and specifications. The parts cover various engine systems like the cylinder block, crankshaft, cylinder head, camshaft, and fuel system.
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 80 tractor service repair m...fjekkdmmem
This document provides a list of components for an engine, including identification numbers, names, and other details. It lists items like cylinders, bearings, plugs, gears, plates, and other engine parts. Quantities and part numbers are provided for each component. Notes indicate some items are only to be ordered as replacements and provide color coding for identifying similar parts.
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 60 tractor service repair m...fjekkdmmem
This document contains parts lists and component information for engines. It lists individual engine parts like cylinders, bearings, plugs, and includes information like part numbers, replacement kits, and quantity per tractor. The parts are associated with assemblies for engines and components like the head, shaft, rockers, and gear kit. Quantity, replacement and reference information is provided for each listed part.
Mc cormick c series c100 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with identification numbers, quantities, and component names. Diagrams show the assembly and placement of parts within various engine and systems. The document provides extensive reference information for locating and identifying replacement parts for several tractor systems.
Mc cormick c series c90 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with descriptions and part numbers needed to service or replace components like the engine, radiator, air cleaner, and exhaust system. Diagrams show the assembly, placement and connections of parts in the various systems. The document provides the information necessary to identify replacement parts for maintenance and repair of engine-related systems.
Mc cormick c series c80 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with descriptions and part numbers needed to service or replace components like the engine, radiator, air cleaner, and exhaust system. Diagrams show the assembly, placement and connections of parts in the various systems. The document provides the information necessary to identify replacement parts for maintenance and repair of engine-related systems.
Kubota b1700 d tractor parts catalogue manualfjekkdmmem
The document provides instructions and definitions for parts books. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It notes country codes that may be included and what they represent. The document then provides an index of parts for Reference B1700D organized by system, with the corresponding part number, description, and parts book reference.
Kubota b1550 hst d tractor parts catalogue manualfjekkdmmem
The document provides instructions and part listings for a parts book. It defines the column headings used in parts book pages including part number, description, quantity, and serial number range. Country codes are also defined, indicating any country-specific differences. The remainder of the document is a sample page from the parts book, listing over 100 individual part numbers for a tractor engine and components.
Kubota b1550 e tractor parts catalogue manualfjekkdmmem
The document provides instructions for parts books. It defines column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for. An example page from a parts book is then shown, listing parts for a B1550E engine with corresponding details.
Cub cadet lt 1222 lawn tractor service repair manualfjekkdmmem
This service manual provides instructions for servicing 1000/1500 series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various engines and drive systems. The manual outlines procedures for removing and replacing components like the hood, fenders, deck, drive belts, brakes, and transaxle. Safety notices advise that the manual is intended for trained technicians experienced with outdoor power equipment.
Cub cadet lt 1050 lawn tractor service repair manualfjekkdmmem
This service manual provides instructions for servicing 1000/1500 Series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various single-cylinder and V-twin engines from Kohler and Kawasaki. The manual describes the different hood, deck, and drive system configurations used on these tractors and provides procedures for removing components like the hood, fenders, deck, and transaxle for repair. Safety notices advise that the manual is intended only for trained technicians experienced with outdoor power equipment.
Claas dominator 98 combine (093) service repair manualfjekkdmmem
The document is a repair manual that provides instructions for repairing various components of CLAAS Dominator 108 VX, 98 VX, and 88 VX combine harvesters. It includes sections on the operator's platform, threshing mechanism, cleaning systems, and other areas. The manual provides detailed steps for removing, dismantling, installing, and assembling parts. It also includes exploded diagrams and specifications to aid in repairs.
Claas dominator 88 combine (092) service repair manualfjekkdmmem
The document is a repair manual that provides instructions for repairing various components of CLAAS Dominator 108 VX, 98 VX, and 88 VX combine harvesters. It includes sections on the operator's platform, threshing mechanism, cleaning systems, and other areas. The manual provides detailed steps for removing, dismantling, installing, and assembling parts. It also includes exploded diagrams and specifications to aid in repairs.
New holland t7.220 power command tractor service repair manualfjekkdmmem
This document is a service manual for Case IH T7 tractor models 220, 235, 250, 260, and 270. It provides specifications and repair/maintenance procedures for the engine, transmission, axles, brakes, hydraulics, pneumatics, hitches, frames, steering, wheels, climate control, and electrical systems of these tractor models. The manual is intended to assist technicians in servicing and repairing components of the tractors. It contains detailed sections on the engine, transmission, axles and other core systems along with part numbers and specifications.
New holland t7.175 auto command stage iv tractor service repair manualfjekkdmmem
This document is a service manual that provides information on servicing various components of tractor models T7.175 AutoCommandTM, T7.175, T7.190 AutoCommandTM, T7.190, T7.210 AutoCommandTM, T7.210, and T7.225 AutoCommandTM. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes, hydraulic systems, pneumatic system, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork and decals. Each section provides removal and installation instructions, specifications
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat Plein
Komatsu pc40 mrx 1 excavator service repair manual sn1001 and up
1.
2.
3.
4.
5.
6.
7. DISASSEMBLY AND ASSEMBLY STARTING MOTOR
REMOVAL OF STARTING
MOTOR ASSEMBLY
PC27MRX, PC30MRX
a Stop the machine on the horizontal ground, then
lower the work equipment completely to the
a
ground and stop the engine.
Disconnect the cable from the negative (-) ter-
minal of the battery.
Remove seat bracket and right and left PPC valve
assembly. For details, see REMOVAL OF SEAT
BRACKET, R.H. AND L.H. PPC VALVE ASSEMBLY.
Disconnect wiring connector (1) (T4).
Remove the boots, then disconnect 2 wires (2).
Remove starting motor assembly (3).
INSTALLATION OF STARTING
MOTOR ASSEMBLY
PC27MRX, PC30MRX
l Carry out installation in the reverse order to re-
moval.
-T-----. lvGiph&-- CWPO6279
30-10
0
PC27 - 45MRX-1
8. DISASSEMBLY AND ASSEMBLY STARTING MOTOR
REMOVAL OF STARTING
MOTOR ASSEMBLY
PC35MRX, PC40MRX, PC45MRX
A .Disconnect the cable from the negative (-) ter-
minal of the battery.
1. Remove air-conditioner unit assembly.
Ir For operator cabin specification machine only.
2. Remove inspection cover (1) at under of operator’s
seat.
3. Disconnect wiring connector (2).
Ir Wiring connector (T4) : PC35MRX
J, Wiring connector (MIO) : PC40MRX, PC45MRX
4. Remove the boots and disconnect 2 wire (3).
5. Remove starting motor assembly (4).
INSTALLATION OF STARTING
MOTOR ASSEMBLY
PC35MRX, PC40MRX, PC45MRX
l Carry out installation in the reverse order to re-
moval.
PC27 - 45MRX- 1 30-l 1
0
9. DISASSEMBLY AND ASSEMBLY ALTERNATOR
REMOVAL OF ALTERNATOR
ASSEMBLY
PC27MRX, PC30MRX
g Stop the machine on the horizontal ground, then
lower the work equipment completely to the
A
ground and stop the engine.
Disconnect the cable from the negative (-1 ter-
minal of the battery.
1.
2.
3.
4.
5.
6.
Remove the cover (I 1.
Disconnect connector (2) (El) and (3) (E2).
Disconnect water temperature sensor connector
(4) (E7).
Remove adjustment bolt (5).
Loosen mounting bolt, and remove alternator belt
(7). m
Remove mounting bolt (6) and remove the alter-
nator assembly (8).
INSTALLATION OF ALTERNATOR
ASSEMBLY
PC27MRX, PC30MRX
l Carry out installation in the reverse order to re-
moval.
* Adjust the alternator belt. For details, see
TESTING AND ADJUSTING, Testing and ad-
justing alternator belt tension.
.3
.2
CWPO6292
30-l 2
0
PC27 - 45MRX-1
10. DISASSEMBLY AND ASSEMBLY ALTERNATOR
REMOVAL OF ALTERNATOR
ASSEMBLY
PC35MRX
A .Disconnect the cable from the negative (-1 ter-
minal of the battery.
1.
6.
Remove the right lever stand assembly (I) with
mounting bracket.
Disconnect wiring connector (2) (El,E2).
Disconnect wire (3).
Loosen mounting bolt and adjustment bolt (4).
Remove adjustment bracket (51, then remove fan
belt (6) from pulley. [a
* It is not enable to remove the fan belt from
pulley, after remove adjustment bracket.
-k There are spacers fitted to the adjustment
bolts so be careful not to drop them.
Remove the alternator assembly (7).
+ There are spacers fitted to the mounting bolts
so be careful not to drop them.
INSTALLATION OF ALTERNATOR
ASSEMBLY
PC35MRX
l Carry out installation in the reverse order to re-
moval.
Adjust the alternator belt. For details, see
TESTING AND ADJUSTING, Testing and ad-
justing alternator belt tension.
PC27 - 45MRX- 1 30-l 3
0
11. DISASSEMBLY AND ASSEMBLY ALTERNATOR
REMOVAL OF ALTERNATOR
ASSEMBLY
PC40MRX, PC45MRX
A .Drsconnect the cable from the negative (-) ter-
minal of the battery.
1. Remove the right side upper cover.
2. Remove the cover (I) between operator’s cab and
hydraulic tank.
3. Disconnect wiring connector (2) (M8, M9).
4. Disconnect wire (3).
5. Loosen mounting bolt and adjustment bolt (4).
6. Remove adjustment bracket (51, then remove fan
belt (6) from pulley. a
* It is not enable to remove the fan belt from
pulley, after remove adjustment bracket.
Sr There are spacers fitted to the adjustment
bolts so be careful not to drop them.
7. Remove the alternator assembly.
* There are spacers fitted to the mounting bolts
so be careful not to drop them.
INSTALLATION OF ALTERNATOR
ASSEMBLY
PC45MRX, PC45MRX
l Carry out installation in the reverse order to re-
moval.
* Adjust the alternator belt. For details, see
TESTING AND ADJUSTING, Testing and ad-
justing alternator belt tension.
30-14
0
PC27 - 45MRX- 1
12. DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
REMOVAL OF FUEL INJECTION
PUMP ASSEMBLY
PC27MRX
A Stop the machine on the horizontal ground, then
lower the work equipment completely to the
g ground and stop the engine.
Disconnect the cable from the negative (-) ter-
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
minal of the battery.
Pull out the fuel control cable pin (I).
Disconnect engine stop solenoid wiring connec-
tor (2) (E3).
Remove lubrication tube (3).
Disconnect fuel supply hose (4).
Disconnect fuel return hose(5).
Ir Spill hose is jointed to fuel return hose.
Disconnect 3 fuel injection tubes (6). m
Remove the cover (7).
Remove the injection mounting nut (8). a
Ir Make sure the impressed mark position.
Remove the drive gear mounting nut (9). m
Be careful not to drop the nut and washer into
the front cover.
Make the matching mark with white paint on
the drive gear and idler gear.
Remove fuel injection pump assembly (IO).
* Using puller 0, push the fuel injection pump
cam shaft and disconnect drive gear, then re-
move fuel injection pump assembly.
* Be careful not to drop the woodruff key into
the case.
PC27 - 45MRX- 1
13. DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
INSTALLATION OF FUEL INJECTION
PUMP ASSEMBLY
PC27MRX
l Carry out installation in the reverse order to re-
moval.
m Sleeve nut : 25.5 f 1.0 Nm I2.6 f 0.1 kgm}
m
* Align the case impressed mark, then tighten
the nut.
m Mounting nut: 3.9f 1.0 Nm IO.4i 0.1 kgm}
113
Ir Align the gear marching marks, then tighten
the nut.
w Mounting nut:
58.8 f 1.0 Nm IS.0 + 0.1 kgm}
30-l 6
0
PC27 - ISMRX- 1
14. DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
REMOVAL OF FUEL INJECTION
PUMP ASSEMBLY
PC30MRX, PC35MRX, PC45MRX
A Stop the machine on the horizontal ground, then
lower the work equipment completely to the
ground and stop the engine.
A Disconnect the cable from the negative (-1 ter-
minal of the battery.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Remove counter weight. For details, see RE-
MOVAL OF COUNTER WHIGHT ASSEMBLY.
Pull out the fuel control cable pin (I) and discon-
nect cable from bracket. m
Ir Check the mounting length, before disconnect
bracket.
Disconnect engine stop solenoid wiring connec-
tor (2).
Ir Wiring connector (E3) :
PC27MRX, PC30MRX, PC35MRX
* Wiring connector (M13) : PC40MRX. PC45MRX
Remove lubrication tube (3).
Disconnect fuel supply hose (4).
Disconnect fuel return hose(5).
* Spill hose is jointed to fuel return hose.
Disconnect 3 fuel injection tubes (6)
Ir PC27MRX, PC30MRX, PC35MRX : 3 tubes
Sr PC40MRX, PC45MRX : 4 tubes
Remove the cover (7).
Remove the injection mounting nut (8). 112
* Make sure the impressed mark..
Remove the drive gear mounting nut (9). m
Be careful not to drop the nut and washer into
the front cover.
Make the matching mark with white paint on
the drive gear and idler gear.
When it is difficult to make the marching mark,
remove radiator l hydraulic cooler assembly.
For details, see REMOVAL OF RADIATOR l HY-
DRAULIC COOLER ASSEMBLY.
Remove fuel injection pump assembly (IO).
Ir Using puller 0, push the fuel injection pump
cam shaft and disconnect drive gear, then re-
move fuel injection pump assembly.
* Be careful not to drop the woodruff key into
the case.
30-17
0
PC27 - 45MRX- 1
15. DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
INSTALLATION OF FUEL INJECTION
PUMP ASSEMBLY
PCSOMR, PC35MR, PC40MR, PC45MR
l Carry out installation in the reverse order to re-
moval.
m
*
m
*
Adjust the fuel control cable. For detail, see
TESTING AND ADUJUSTING, Adjusting fuel
control cable.
Align the case impressed mark, then tighten
the nut.
m Injection pump mounting nut :
20.58 + 0.98 Nm I2.1 * 0.1 kgm}
w
Ir Align the gear marching marks, then tighten
the nut.
QK! Drive gear mounting nut :
63.7 + 4.9 Nm 16.5 + 0.5 kgm}
30-18
0
PC27 - 45MRX- 1
16. DISASSEMBLY AND ASSEMBLY NOZZLE HOLDER
REMOVAL OF NOZZLE HOLDER
ASSEMBLY
PC27MRX
A Stop the machine on the horizontal ground, then
lower the work equipment completely to the
ground and stop the engine.
A Disconnect the cable from the negative (-) ter-
minal of the battery.
1.
2.
Remove air inlet hoses (I) and (2).
Remove the mounting bolt (3) and remove air
cleaner assembly (4).
3. Remove air cleaner mounting bracket (5).
4. Remove fuel injection tube (6). m
5. Disconnect spill hose, then remove retainer (7).
6. Remove nozzle holder assembly (8).
INSTALLATION OF NOZZLE
HOLDER ASSEMBLY
PC27MRX
l Carry out installation in the reverse order to re-
moval.
m
w Sleeve nut : 25.5 + 1.0 Nm (2.6 f 0.1 kgm}
m
B Retainer mounting nut :
3.9 _+1.0 Nm to.4 f 0.1 kgm)
When assembling the nozzle holder, clean the
nozzle holder mount, and check that there is
no dust inside the sleeve before assembling.
PC27 - 45MRX- 1 30-19
0
17. REMOVAL OF NOZZLE HOLDER
ASSEMBLY
PCSOMRX, PC35MRX, PC4OMRX, PC45MRX
g Stop the machine on the horizontal ground, then
lower the work equipment completely to the
negative (-) ter-
1. Remove air inlet hoses (I 1and (2). m
2. Remove the mounting bolt (3) ,then remove air
cleaner assembly (4).
3. Remove air cleaner mounting bracket (5).
4. Remove fuel injection tube (6).
5. Disconnect spill hose (7).
6. Remove retainer (8).
7. Remove nozzle holder assembly (9).
INSTALLATION OF NOZZLE
HOLDER ASSEMBLY
PCSOMRX, PC35MRX, PC40MRX, PC45MRX
l Carry out installation in the reverse order to re-
moval.
DISASSEMBLY AND ASSEMBLY NOZZLE HOLDER
m Intake air hose clamp :
5.9 ? 0.49 Nm {SO + 5 kgcml
m Retainer mounting nut :
4.41 + 0.49 Nm (0.45 + 0.05 kgml
* When assembling the nozzle holder, clean the
nozzle holder mount, and check that there is
no dust inside the sleeve before assembling.
30-20 PC27 - 45MRX- 1
18. DISASSEMBLY AND ASSEMBLY WATER PUMP
REMOVAL OF WATER PUMP
ASSEMBLY
A Stop the machine on the horizontal ground, then
lower the work equipment completely to the
ground and stop the engine.
a Disconnect the cable from the negative (-) ter-
minal of the battery.
1. Remove radiator l oil cooler assembly (1). For de-
tails, see REMOVE OF RADIATOR l HYDRAULIC
COOLER ASSEMBLY.
2. Loosen alternator mounting bolt, then remove al-
ternator belt (2) from alternator pulley. m
3. Remove fan (3) mounting bolt. then remove pul-
ley (4) and alternator belt together.
+ Fan pulley and fan are tighten together.
4. Remove mounting bolt (5), then remove the wa-
ter pump assembly (6). m
INSTALLATION OF WATER
PUMP ASSEMBLY
l Carry out installation in the reverse order to re-
moval.
Ir Adjust the alternator belt tension. For details,
see TESTING AND ADJUSTING, testing and
adjusting alternator belt tension.
w Water pump mounting bolt :
10.78 f 1.96 Nm Il.1 f 0.2 kgm}
l Refilling with water
Add water through water filler to the specified
level. Run the engine to circulate the water
through the system. Then check the water level
by reserve tank again.
PC27 - 45MRX- 1 30-21
a
19. DISASSEMBLY AND ASSEMBLY THERMOSTAT
REMOVAL OF THERMOSTAT
ASSEMBLY
g Stop the machine on the horizontal ground, then
lower the work equipment completely to the
ground and stop the engine.
1. Disconnect radiator inlet hose (I ). m
2. Remove mounting bolt, then remove cover (2).
3. Remove thermostat assembly (3).
IIINSTALLATION OF
THERMOSTAT ASSEMBLY
l Carry out installation in the reverse order to re-
moval.
QFI Radiator inlet hose clamp :
8.8 f 0.5 Nm I90 + 5 kgcml
l Refilling with water
Add water through water filler to the specified
level. Run the engine to circulate the water
through the system. Then check the water level
by reserve tank again.
30-22
0
PC27 - 45MRX-1
20. DISASSEMBLY AND ASSEMBLY ENGINE FRONT SEAL
REMOVAL OF ENGINE FRONT
SEAL
1.
2.
3.
4.
5.
Remove radiator and hydraulic cooler assembly.
For details, see REMOVAL OF RADIATOR HY-
DRAULIC COOLER ASSEMBLY.
Loosen alternator mounting bolt, then remove al-
ternator belt (2) from alternator pulley. m
Remove fan (3) mounting bolt. then remove pul-
ley (4) and alternator belt together.
Ir Fan pulley and fan are tighten together.
Remove bolt (5) and spacer (61, and tighten the
bolt (5) 2 to 4 turns again, then remove crank pul-
ley (7) using puller 0. 112
Remove engine front seal (8). a
INSTALLATION OF ENGINE
FRONT SEAL
l Carry out installation in the reverse order to re-
moval.
Ir Adjust the alternator belt tension. For details,
see TESTING AND ADJUSTING, Testing and
adjusting alternator belt tension.
m Crankshaft pulley mounting bolt :
112.7+~* Nm {11.5+:” kgm}
& Lip of oil seal : Engine oil (EOSO-CD)
w / 1 CWPO6406
I
CWPO6407
PC27 - 45MRX- 1 30-23
0
21. DISASSEMBLY AND ASSEMBLY
ENGINE REAR SEAL
REMOVING OF ENGINE REAR
SEAL
1. Remove the damper assembly. For details, see
REMOVAL OF DAMPER ASSEMBLY
2. Remove the flywheel (1). m
3. Remove the seal case (2). a
* Since the seal case has notches on the both
ends, prize the case with screwdriver to re-
move it.
4. Remove the engine rear seal (3) from the seal
case. m
CLPO2630
30-24
0
PC27 - 45MRX- 1
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. DISASSEMBLY AND ASSEMBLY ENGINE REAR SEAL
INSTALLATION OF ENGINE
REAR SEAL
. Carry out installation in the reverse order to re-
moval.
,Q& Seal mounting face of seal case and oil seal
lip : Engine oil (E030XD)
Ir Press fit the oil seal until it comes to the same
level as the seal case.
6 Seal case mounting face :
Gasket sealant (LG-7)
* Tighten the flywheel mounting bolts in the or-
der shown in the drawing on the right.
w Flywheel mounting bolt :
85.75 f 2.45 Nm 18.75 k 0.25 kgm)
* After installing the flywheel, check it for fa-
cial runout and radial runout with dial gauge
0.
l Facial runout : 0.20mm max.
l Radial runout : 0.20mm max.
PC27 - 45MRX-1 30-25
0
24. DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
REMOVAL OF CYLINDER HEAD
ASSEMBLY
a Stop the machine on the horizontal ground, then
lower the work equipment completely to the
a
ground and stop the engine.
Disconnect the cable from the negative (-) ter-
1.
2.
3.
4.
Remove seat bracket, right and left PPC valve as-
sembly. For details, see REMOVAL OF SEAT
BRACKET, R.H. AND L.H. PPC VALVE ASSEMBLY.
(PC27MRX, PC30MRX)
Remove seat bracket assembly. For details, see
REMOVAL OF SEAT BRACKET ASSEMBLY.
(PC35MRX)
Remove floor frame assembly. For details, see RE-
MOVAL OF FLOOR FRAME ASSEMBLY.
(PC40MRX, PC45MRX)
Remove counterweight assembly. For details, see
REMOVAL OF COUNTERWEIGHT ASSEMBLY.
5. Disconnect air intake hose (21, (3).
6. Remove air cleaner (4).
7. Remove air cleaner bracket (5).
8. Disconnect fuel filter (6) from cylinder head.
9. Disconnect fuel injection tube (7).
10.
11.
12.
Disconnect heater wire (8) from intake manifold.
Disconnect spill hose (9).
Disconnect wiring connector (IO) from intake
manifold.
Sr Wiring connector (E3) :
PC27MRX, PC30MRX, PC35MRX
Ir Wiring connector (M13) : PC40MRX, PC45MRX
minal of the battery.
I
30-26
a
PC27 - 45MRX- 1
25. DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Disconnect bracket (11) mounting bolt from en-
gine block, then remove muffler (12).
t Before disconnect mounting bolt, remove
muffler from exhaust manifold.
Remove exhaust manifold (13).
Disconnect wiring connector (14).
* Wiring connector (E7):
PC27MRX, PC30MRX, PC35MRX
Ir Wiring connector (P2): PC40MRX, PC45MRX
Remove alternator adjusting bracket (15). m
Remove radiator, hydraulic cooler assembly. For
details, see REMOVAL OF RADIATOR, HYDRAU-
LIC COOLER ASSEMBLY.
Remove alternator belt (17) and fan (18).
Remove water pump mounting bolt, then remove
water pump assembly (19).
Remove cylinder head cover (20).
Disconnect spill hose (21), then remove nozzle
holder assembly (22) after remove retainer. m
Remove rocker arm assembly. m
* Loosen the locknut, then loosen the adjust-
ment screw 2 to 3 turns.
Remove push rod (24).
Remove cylinder head mounting bolts, then re-
move cylinder head assembly (26). m
* Disconnect air intake manifold, after remove
cylinder head.
i8
CWPO6418
PC27 - 45MRX-1 30-27
0