The document provides instructions for splitting a tractor by removing components that connect the front and rear sections, including the steering lines, fuel tank, transmission oil, and installing lifting brackets. Support stands are placed under the tractor for stability during separation. The front and rear sections are then separated by lifting with the installed brackets.
John deere 6100 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
This document provides instructions for splitting a tractor into front and rear sections. Key steps include: blocking the wheels, removing the cab or operator station, draining fluids, disconnecting hydraulic lines, and installing lifting brackets to separate the front and rear sections using a lifting device. Safety precautions such as using support stands are noted. The process is reversed to rejoin the sections.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f85 fgexl tractor service r...udfjjjskekmdm
This document provides component part numbers and descriptions for engine repairs and replacements. It includes kits for replacing engine parts between specific serial numbers, as well as individual replacement parts like pistons, rods, bearings, gaskets, plugs, and other engine components. Repair codes indicate whether components should be replaced or overhauled.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f80 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and technical specifications for components of Perkins diesel engines. It includes items like cylinders, crankshafts, pistons, rods, valves, heads, pumps, and other engine parts. Repair and replacement procedures are indicated for some components, with time estimates provided. Serial numbers and engine models are referenced for applicability.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f75 fgexl tractor service r...udfjjjskekmdm
This document provides component part information for the repair and replacement of engine parts. It includes lists of components with identification numbers, replacement part numbers, and other technical specifications. Components listed include pistons, rods, crankshafts, pumps, gears, valves, plugs, gaskets and other engine parts. Replacement part kits and overhaul kits are also specified for various engine components.
John deere 6100 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
This document provides instructions for splitting a tractor into front and rear sections. Key steps include: blocking the wheels, removing the cab or operator station, draining fluids, disconnecting hydraulic lines, and installing lifting brackets to separate the front and rear sections using a lifting device. Safety precautions such as using support stands are noted. The process is reversed to rejoin the sections.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f85 fgexl tractor service r...udfjjjskekmdm
This document provides component part numbers and descriptions for engine repairs and replacements. It includes kits for replacing engine parts between specific serial numbers, as well as individual replacement parts like pistons, rods, bearings, gaskets, plugs, and other engine components. Repair codes indicate whether components should be replaced or overhauled.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f80 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and technical specifications for components of Perkins diesel engines. It includes items like cylinders, crankshafts, pistons, rods, valves, heads, pumps, and other engine parts. Repair and replacement procedures are indicated for some components, with time estimates provided. Serial numbers and engine models are referenced for applicability.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f75 fgexl tractor service r...udfjjjskekmdm
This document provides component part information for the repair and replacement of engine parts. It includes lists of components with identification numbers, replacement part numbers, and other technical specifications. Components listed include pistons, rods, crankshafts, pumps, gears, valves, plugs, gaskets and other engine parts. Replacement part kits and overhaul kits are also specified for various engine components.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f70 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and repair instructions for engine components. It lists individual parts, part numbers, quantities needed and repair/replacement instructions. It provides details on repairs, overhauls and replacements for the engine, including the cylinder head, crankshaft, pistons, valves, camshaft and other internal components.
Mc cormick f top restyling (2010 ) - rp55 - f100gexl tractor service repair ...udfjjjskekmdm
This document provides parts information for various engine components. It includes descriptions of parts, part numbers, serial number ranges and replacement part numbers. Images show diagrams of engine assemblies and components with corresponding part numbers and other technical specifications. The document also indicates if parts are for replacement or are not serviced individually.
Komatsu h185 s hydraulic shovel service repair manual (sn 6111)udfjjjskekmdm
This shop manual provides proprietary information for maintaining and repairing the Komatsu H185S hydraulic shovel. It describes the continuous improvement process used by Komatsu to update their products and documentation. Users are advised to check with their distributor for the latest revision of the manual, as revisions may be made without notice due to Komatsu's ongoing research and development efforts.
Komatsu d575 a 2 dozer bulldozer service repair manual (sn 10001 and up)udfjjjskekmdm
This shop manual provides maintenance and repair instructions for the D575A-2 machine model. The manual contains information on machine structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. It summarizes that the D575A-2 mounts the SA12V170-1 engine and refers technicians to the 12V170-1 Series Engine Shop Manual for engine details. The document provides safety precautions and instructions for removing and installing components like the power train oil cooler assembly, hydraulic cooler assembly, and fuel injection pump assemblies.
Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)udfjjjskekmdm
This document provides instructions for removing and installing various components of a Komatsu D475A-2 machine. It describes how to remove and install the torque converter cooler assembly, fuel injection pump assembly, water pump assembly, turbocharger assembly, aftercooler core assembly, nozzle holder assembly, cylinder head assembly, fuel tank assembly, and radiator assembly. The instructions include lists of parts to disconnect or remove for each component and the order of removal and installation steps. Weights and tightening specifications are provided for some components.
Komatsu d65 wx 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 wx 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, component diagrams, maintenance procedures, troubleshooting guides, and other technical details. Serial numbers for the models start at 69001. The document is divided into sections covering topics like specifications, engine and cooling systems, power train, undercarriage, hydraulic and electrical systems, and testing and troubleshooting procedures.
Komatsu d65 wx 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which has a SA6D125E-3 engine. It lists 14 steps for removal, including disconnecting wiring, removing hoses and pipes, and taking off covers. Special tools are required for safely removing the fuel supply pump.
Komatsu d65 px 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 px 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and service information for Bulldozer models D65EX-15E0, D65PX-15E0, and D65WX-15E0, including serial numbers 69001 and up. It contains sections on specifications, structure and function, maintenance standards, testing and adjusting procedures, and troubleshooting. The document is organized into multiple sections covering various systems of the bulldozers.
Komatsu d65 px 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing mounting hardware and high pressure pipes, and using special tools to extract the pump from the engine case. Workers are advised to take safety precautions and release fuel pressure before performing these tasks.
Komatsu d65 px 12 dozer bulldozer service repair manual sn 65275 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator. It contains general safety precautions and procedures for testing, disassembly, assembly, and maintenance. The document summarizes how to remove and install the fuel supply pump assembly and nozzle holder assembly, including disconnecting wiring and piping, loosening mounting hardware, and reversing steps for installation. Proper torque specifications are listed for reinstalling components.
Komatsu d65 ex 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
The document is a shop manual that provides specifications, maintenance procedures, and troubleshooting information for Bulldozer models D65EX-16, D65PX-16, and D65WX-16. It contains sections on the engine and cooling system, power train, undercarriage, hydraulic system, electrical system, and troubleshooting codes. The manual includes diagrams, specifications, maintenance standards, and step-by-step instructions for repairs and adjustments.
Komatsu d65 ex 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, dimensions, weights, lubricant types, and sections covering the engine/cooling systems, power train, undercarriage, hydraulic system, electrical system, and troubleshooting procedures. Serial numbers for the models start at 69001 and up. The document contains diagrams, specifications, testing and maintenance procedures to service these bulldozer models.
Komatsu d65 ex 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing covers and pipes, and taking out the pump. Proper safety precautions are emphasized, such as releasing fuel pressure, wearing protective equipment, and having an assistant when working on rotating parts.
Komatsu d65 ex 12 dozer bulldozer service repair manual sn 65209 and upudfjjjskekmdm
1) This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator.
2) The D65EX/PX-12 uses the SA6D125E-3 engine, with engine service details covered in a separate manual.
3) Proper safety precautions must be followed when servicing equipment, including the use of protective equipment and blocking of moving parts.
John deere 6200 tractors service repair technical manual (tm4523)udfjjjskekmdm
The document provides instructions for assembling and repairing the creeper transmission for tm4523 tractors. It details installing components like connecting rings, snap rings, gears, bearings, and shift collars. Specifications are provided for measurements and torque values. The final section covers general repair procedures for the range transmission, emphasizing cleanliness and care when handling precision machined parts.
John deere 6200 tractors service repair technical manual (tm4493)udfjjjskekmdm
This document provides instructions for adjusting the cone point on differentials for 6100 to 6600 tractors. It involves measuring specific dimensions, calculating the required spacer washer thickness, and selecting the appropriate washers. The final section lists some special tools needed for tasks like tilting the cab, supporting the tractor during wheel removal, and removing/installing shafts.
John deere 6125 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
The document provides instructions for removing and installing a final drive assembly on a tractor. It involves draining the oil, removing mounting hardware and brackets, using lifting equipment to remove the assembly, cleaning and applying sealant to mating surfaces, and reinstalling the assembly. Inspecting parts for wear or damage and replacing as needed is also specified. Proper torque specifications for fasteners are listed to complete the process.
John deere 6115 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
The document provides instructions for removing and installing a final drive assembly on a tractor. It involves draining the oil, removing mounting hardware and brackets, using lifting equipment to remove the assembly, cleaning and applying sealant to mating surfaces, and reinstalling the assembly. Inspection and replacement of worn parts is also specified. The process is completed by refilling the oil and checking the level.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f70 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and repair instructions for engine components. It lists individual parts, part numbers, quantities needed and repair/replacement instructions. It provides details on repairs, overhauls and replacements for the engine, including the cylinder head, crankshaft, pistons, valves, camshaft and other internal components.
Mc cormick f top restyling (2010 ) - rp55 - f100gexl tractor service repair ...udfjjjskekmdm
This document provides parts information for various engine components. It includes descriptions of parts, part numbers, serial number ranges and replacement part numbers. Images show diagrams of engine assemblies and components with corresponding part numbers and other technical specifications. The document also indicates if parts are for replacement or are not serviced individually.
Komatsu h185 s hydraulic shovel service repair manual (sn 6111)udfjjjskekmdm
This shop manual provides proprietary information for maintaining and repairing the Komatsu H185S hydraulic shovel. It describes the continuous improvement process used by Komatsu to update their products and documentation. Users are advised to check with their distributor for the latest revision of the manual, as revisions may be made without notice due to Komatsu's ongoing research and development efforts.
Komatsu d575 a 2 dozer bulldozer service repair manual (sn 10001 and up)udfjjjskekmdm
This shop manual provides maintenance and repair instructions for the D575A-2 machine model. The manual contains information on machine structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. It summarizes that the D575A-2 mounts the SA12V170-1 engine and refers technicians to the 12V170-1 Series Engine Shop Manual for engine details. The document provides safety precautions and instructions for removing and installing components like the power train oil cooler assembly, hydraulic cooler assembly, and fuel injection pump assemblies.
Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)udfjjjskekmdm
This document provides instructions for removing and installing various components of a Komatsu D475A-2 machine. It describes how to remove and install the torque converter cooler assembly, fuel injection pump assembly, water pump assembly, turbocharger assembly, aftercooler core assembly, nozzle holder assembly, cylinder head assembly, fuel tank assembly, and radiator assembly. The instructions include lists of parts to disconnect or remove for each component and the order of removal and installation steps. Weights and tightening specifications are provided for some components.
Komatsu d65 wx 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 wx 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, component diagrams, maintenance procedures, troubleshooting guides, and other technical details. Serial numbers for the models start at 69001. The document is divided into sections covering topics like specifications, engine and cooling systems, power train, undercarriage, hydraulic and electrical systems, and testing and troubleshooting procedures.
Komatsu d65 wx 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which has a SA6D125E-3 engine. It lists 14 steps for removal, including disconnecting wiring, removing hoses and pipes, and taking off covers. Special tools are required for safely removing the fuel supply pump.
Komatsu d65 px 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 px 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and service information for Bulldozer models D65EX-15E0, D65PX-15E0, and D65WX-15E0, including serial numbers 69001 and up. It contains sections on specifications, structure and function, maintenance standards, testing and adjusting procedures, and troubleshooting. The document is organized into multiple sections covering various systems of the bulldozers.
Komatsu d65 px 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing mounting hardware and high pressure pipes, and using special tools to extract the pump from the engine case. Workers are advised to take safety precautions and release fuel pressure before performing these tasks.
Komatsu d65 px 12 dozer bulldozer service repair manual sn 65275 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator. It contains general safety precautions and procedures for testing, disassembly, assembly, and maintenance. The document summarizes how to remove and install the fuel supply pump assembly and nozzle holder assembly, including disconnecting wiring and piping, loosening mounting hardware, and reversing steps for installation. Proper torque specifications are listed for reinstalling components.
Komatsu d65 ex 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
The document is a shop manual that provides specifications, maintenance procedures, and troubleshooting information for Bulldozer models D65EX-16, D65PX-16, and D65WX-16. It contains sections on the engine and cooling system, power train, undercarriage, hydraulic system, electrical system, and troubleshooting codes. The manual includes diagrams, specifications, maintenance standards, and step-by-step instructions for repairs and adjustments.
Komatsu d65 ex 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, dimensions, weights, lubricant types, and sections covering the engine/cooling systems, power train, undercarriage, hydraulic system, electrical system, and troubleshooting procedures. Serial numbers for the models start at 69001 and up. The document contains diagrams, specifications, testing and maintenance procedures to service these bulldozer models.
Komatsu d65 ex 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing covers and pipes, and taking out the pump. Proper safety precautions are emphasized, such as releasing fuel pressure, wearing protective equipment, and having an assistant when working on rotating parts.
Komatsu d65 ex 12 dozer bulldozer service repair manual sn 65209 and upudfjjjskekmdm
1) This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator.
2) The D65EX/PX-12 uses the SA6D125E-3 engine, with engine service details covered in a separate manual.
3) Proper safety precautions must be followed when servicing equipment, including the use of protective equipment and blocking of moving parts.
John deere 6200 tractors service repair technical manual (tm4523)udfjjjskekmdm
The document provides instructions for assembling and repairing the creeper transmission for tm4523 tractors. It details installing components like connecting rings, snap rings, gears, bearings, and shift collars. Specifications are provided for measurements and torque values. The final section covers general repair procedures for the range transmission, emphasizing cleanliness and care when handling precision machined parts.
John deere 6200 tractors service repair technical manual (tm4493)udfjjjskekmdm
This document provides instructions for adjusting the cone point on differentials for 6100 to 6600 tractors. It involves measuring specific dimensions, calculating the required spacer washer thickness, and selecting the appropriate washers. The final section lists some special tools needed for tasks like tilting the cab, supporting the tractor during wheel removal, and removing/installing shafts.
John deere 6125 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
The document provides instructions for removing and installing a final drive assembly on a tractor. It involves draining the oil, removing mounting hardware and brackets, using lifting equipment to remove the assembly, cleaning and applying sealant to mating surfaces, and reinstalling the assembly. Inspecting parts for wear or damage and replacing as needed is also specified. Proper torque specifications for fasteners are listed to complete the process.
John deere 6115 d (tier 0 tier 3stage iiia) tractors service repair technic...udfjjjskekmdm
The document provides instructions for removing and installing a final drive assembly on a tractor. It involves draining the oil, removing mounting hardware and brackets, using lifting equipment to remove the assembly, cleaning and applying sealant to mating surfaces, and reinstalling the assembly. Inspection and replacement of worn parts is also specified. The process is completed by refilling the oil and checking the level.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
John deere 6130 d (tier 0 tier 3stage iiia) tractors service repair technical manual (tm608819)
1. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier 3/Stage IIIA)
Tractors Repair Technical Manual(60000—), 11/2014—
Remove and Install Final Drive Assembly
Remove and Install Final Drive Assembly
1. NOTE:
It is not necessary to remove fuel tank, but doing so may ease removal and installation of left-hand final drive.
(See Remove and Install Fuel Tank in Section 30, Group 05.)
PUC2088-UN: Final Drive Drain
LEGEND:
A - Drain Plug
Remove final drive drain plug (A) to drain oil into suitable container.
2. Install drain plug (A).
3.
PUC2208-UN: .
LEGEND:
A - Cap Screw (4 used)
Loosen the cab mounting cap screws. Remove cap screw (A) while removing final drive housing.
1/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
2. 4.
PUC3808-UN: Right-Hand Side Half Axle
LEGEND:
B - Screw (2 used)
C - SCV Mounting Braket
Loosen SCV mounting bracket (C) by removing cap screws (B) while removing final drive housing.
5.
PY20649-UN: Left Hand Side Half Axle
LEGEND:
D - Cap Screws
E - Transmission Harness
F - Bracket
Loosen transmission harness bracket (F) by removing cap screws (D) while removing the final drive housing.
6.
CAUTION:
Prevent bodily injury caused by accidental dropping of tractor when removing wheel. Use jack and floor
stands with a minimum capacity of 4540 kg (10,000 lb.).
2/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
3. PUC2089-UN: Jacking of Tractor
Jack tractor from under drawbar support and set jack stands under front of drawbar.
7.
CAUTION:
The approximate weight of the wheel and tire assembly is 260 kg (573.20 lb.).
Remove left-hand wheel assembly. (See Remove and Install Front and Rear Wheels in Section 80, Group 15.)
8.
PY20651-UN: .
Item Measurement Specification
Wheel and Tire Weight 260 kg
(573.20 lb.)
3/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
4. PY20650-UN: .
LEGEND:
A - Cotter Pin
B - Pin
C - Bracket, Link Arm
D - Cap Screw (3 used)
Remove cotter pin (A) and pin (B).
9. Remove cap screws (D) and link arm bracket (C).
10.
PUC2092-UN: .
LEGEND:
A - Lifting Device
B - Eyebolt (2 used)
C - Cap Screw (10 used)
Install eyebolts (B) into existing holes.
11. Attach a suitable lifting device (A).
12. Remove cap screws (C) and final drive from transaxle.
4/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
5. 13.
PUC2093-UN: Final Drive Axle
Remove pinion shaft.
14. Inspect all parts for wear or damage. Replace as necessary.
15. Install pinion shaft.
16.
PUC2094-UN: Final Drive Mating Surface
LEGEND:
A - Transaxle Housing
Clean mating surfaces of final drive and transaxle housing (A) using TY16285 Cure Primer.
17. Apply TY6304 Flexible Sealant to mating surfaces.
18. NOTE:
Gently rotate axle while positioning the final drive pinion into the planetary gears.
Install final drive assembly onto transaxle housing.
19. NOTE:
Tighten all cap screws, using a crisscross pattern, when housings are mated.
Tighten cap screws to specification.
Item Measurement Specification
5/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
6. 20.
PY20651-UN: .
PY20650-UN: .
LEGEND:
A - Cotter Pin
B - Pin
C - Bracket, Link Arm
D - Cap Screw (3 used)
Install link arm bracket (C) and cap screws (D).
21. Install pin (B) and cotter pin (A).
22.
CAUTION:
The approximate weight of the wheel and tire assembly is 260 kg (573.20 lb.).
Final Drives
Final Drive Assembly Cap Screw Torque 345 N·m
(255 lb.-ft.)
Item Measurement Specification
Wheel and Tire Weight 260 kg
(573.20 lb.)
6/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
7. Install wheel assembly. (See Remove and Install Front and Rear Wheels in Section 80, Group 15.)
23.
PUC2089-UN: Jacking of Tractor
Raise tractor using a floor jack under drawbar support; then remove jack stands under front of drawbar.
24. Install fuel tank if previously removed. (See Remove and Install Fuel Tank in Section 30, Group 05.)
25.
PUC3808-UN: Right-Hand Side Half Axle
LEGEND:
B - Screw (2 used)
C - SCV Mounting Braket
Install screws (B) to install SCV bracket mounting (C).
7/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
8. 26.
PY20649-UN: Left Hand Side Half Axle
LEGEND:
D - Cap Screws
E - Transmission Harness
F - Bracket
Install cap screws (D) to install transmission harness bracket (F).
27.
PUC2208-UN: .
LEGEND:
A - Cap Screw (4 used)
Install cab mounting cap screws (A). Tighten to specification.
Item Measurement Specification
Cab Mounting Cap Screw Torque 610 N·m (450 lb.-ft.)
8/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
9. 28.
P9073-UN: Sight Glass
LEGEND:
A - Sight Glass
Fill transaxle housing until fluid level is visible between two marks on sight glass (A) with specified transmission/hydraulic oil. (See
Section 10 for recommended oil.)
29. Start engine and run for 5 min.
30. Shut off engine and wait 5 min. before rechecking oil level in sight glass.
31. Add additional oil as necessary.
Loctite is a trademark of Henkel Corporation AK50421,0000121-19-20141001
9/9
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
10. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier
3/Stage IIIA) Tractors Repair Technical Manual(60000—), 11/2014—
Remove, Inspect and Install MFWD Drive Shaft
Remove, Inspect and Install MFWD Drive Shaft
1.
PUC2096-UN: Rear Shield
LEGEND:
A - Cap Screw (2 used)
B - Shield
Loosen cap screws (A) and remove rear shield (B).
2.
PUC2097-UN: Front Shield
LEGEND:
A - Cap Screw (2 used)
B - Shield
Remove cap screws (A) and front shield (B).
1/4
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa826...
11. 3.
PUC2098-UN: Cap Screw
LEGEND:
A - Cap Screw (4 used)
Remove cap screws (A) and lower shaft to ground. Slide drive shaft off splined output shaft of MFWD drop
gearbox.
4. Inspect for wear or damage. Check drive shaft for straightness. Replace as necessary.
5. Apply TY6341 Multi-Purpose SD Polyurea Grease to internal splines of drive shaft end.
6.
PUC2099-UN: Drive Shaft
LEGEND:
A - MFWD Output Shaft
B - Drive Shaft
Install drive shaft (B) onto MFWD output shaft (A).
2/4
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa826...
12. 7.
PUC2098-UN: .
LEGEND:
A - Cap Screw (4 used)
Install flange to shaft using cap screws (A).
8.
PUC2097-UN: Front Shield
LEGEND:
A - Cap Screw (2 used)
B - Shield
Install front shield (B) using cap screws (A).
3/4
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa826...
13. 9.
PUC2096-UN: Rear Shield
LEGEND:
A - Cap Screw (2 used)
B - Shield
Install rear shield (B) and tighten cap screws (A).
OURX984,0000131-19-20140326
4/4
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa826...
14. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier
3/Stage IIIA) Tractors Repair Technical Manual(60000—), 11/2014—
Remove and Install MFWD Drop Gearbox
Remove and Install MFWD Drop Gearbox
1.
PUC2085-UN: MFWD Drop Box Drain
PUC2100-UN: .
PUC2101-UN: .
LEGEND:
A - Plug, Drop Gearbox
1/2
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
15. B - Cotter Pin (2 used)
C - Linkage
D - Cap Screw (8 used)
Remove drive shaft. (See Remove, Inspect and Install MFWD Drive Shaft in this group.)
2. Remove plug (A) and drain oil.
3. Remove cotter pins (B), and disconnect mechanical front wheel drive engagement linkage (C).
4. Remove cap screws (D) and remove drop gearbox.
5. Make repairs as necessary. (See procedures in this section.)
6. Clean mating surfaces of drop gearbox case and transaxle housing using TY16285 Cure Primer.
7. Apply a coat of TY6304 Flexible Form-in-Place Gasket.
8. Install drop gearbox. Tighten cap screws (D) to specification.
9. Install mechanical front wheel drive engagement linkage (C) using cotter pin (B).
10. Install drive shaft. (See Remove, Inspect and Install MFWD Drive Shaft in this group.)
11.
P9073-UN: Sight Glass
LEGEND:
A - Sight Glass
Fill transaxle housing until fluid level is visible between two marks on sight glass (A). (See Section 10 for
recommended oil.)
12. Start engine and run for 5 min.
13. Shut off engine and wait 5 min. before rechecking oil level in sight glass.
14. Add additional oil as necessary.
Item Measurement Specification
Drop Gearbox Mounting Cap
Screws
Torque 100—150 N·m
(47—111 lb.-ft.)
Loctite is a trademark of Henkel Corporation AK50421,00000FE-19-20141001
2/2
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
16. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier
3/Stage IIIA) Tractors Repair Technical Manual(60000—), 11/2014—
Split Tractor
Split Tractor
1.
PY20652-UN: Steering Lines
LEGEND:
A - Steering Line
B - Oil Cooler Line
C - Clamp
D - Cap Screw
E - Mid Frame
Block front wheels.
2. Block front wheel axle.
3. Cab Tractor: Remove cab. (See Remove Operator Cab, in Section 95, Group 00.)
4. OOS Tractor: Remove open operator's station. (See Remove Operator Station, in Section 90, Group 15.)
5. Remove MFWD drive shaft, if equipped. (See Remove, Inspect, and Install MFWD Drive Shaft, in Section 50, Group
05.)
6. Remove fuel tank (See Remove and Install Fuel Tank, Section 30, Group 05.)
7. Drain transmission oil.
8. Perform the following steps on right-hand side of tractor: Identify, label, and disconnect steering oil supply line (A)
and oil cooler line (B from mid frame (E).
9. Remove clamp (C) by removing cap screw (D) and remove oil lines (A and B)..
1/5
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
17. 10.
RXA0128540-UN: Support Stands
LEGEND:
A - Support Stands
Place support stands (A) on tractor for stability when separating.
11.
PY20653-UN: JDG19 Lifting Brackets
2/5
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
18. PY20657-UN: .
LEGEND:
A - JDG19 Lifting Eyes
B - Cap Screws (9 used)
C - Cap Screw (1 used)
Install JDG19 Lifting Eyes (A) onto clutch housing on both sides of tractor.
12. Attach chains or lift straps to lifting eyes and an overhead lifting device.
13. Remove cap screws (B) attaching mid-frame to fly wheel housing.
14. Remove cap screw (C) from clutch housing side as shown.
15.
PY20654-UN: Drive Train Assembly
3/5
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
19. LEGEND:
A - Drive Train Assembly
Carefully separate drive train assembly (A) from fly wheel housing.
16. Install in reverse order.
PY20655-UN: Cap Screws
PY20656-UN: .
LEGEND:
A - M20 x 2.5 x 110 Cap Screw (4 used)
B - M16 x 2 x 90 Cap Screw (3 used)
C - M20 x 2.5 x 90 Cap Screw (2 used)
D - M16 x 2 x 70 Cap Screw (1 used)
Install cap screws (A, B, C and D) and tighten to specification.
Item Measurement Specification
Flywheel Housing-to-Clutch
Housing Mounting Bolts
Torque 542 N·m
(400 lb.-ft.)
4/5
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa829...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier
3/Stage IIIA) Tractors Repair Technical Manual(60000—), 11/2014—
PTO Repair—Use CTM
PTO Repair—Use CTM
For complete repair information use component technical manual (CTM). Use the appropriate component manual in
conjunction with this machine manual.
OURX984,000141C-19-20120914
1/1
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa81d...
22. TM608819 - 6100D, 6110D, 6115D, 6125D and 6130D(Tier 0 —Tier
3/Stage IIIA) Tractors Repair Technical Manual(60000—), 11/2014—
Other Material
Other Material
Number Name Use
Petroleum Jelly Lubricate PTO Shaft
TY6333 (U.S.) Special Purpose HD Moly Grease Lubricate Splines on End of PTO
Shaft
AC20456,0001890-19-20120828
1/1
2020/7/11file:///C:/ProgramData/Service%20ADVISOR/Temp/TM608819_09001faa81d...