This document provides instructions for removing and installing various components of a Komatsu D475A-2 machine. It describes how to remove and install the torque converter cooler assembly, fuel injection pump assembly, water pump assembly, turbocharger assembly, aftercooler core assembly, nozzle holder assembly, cylinder head assembly, fuel tank assembly, and radiator assembly. The instructions include lists of parts to disconnect or remove for each component and the order of removal and installation steps. Weights and tightening specifications are provided for some components.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualfjsjjekdkme
This document provides specifications for a Massey Ferguson MF 362 N tractor intended for the Japanese market only. It includes detailed parts lists and descriptions for the engine, cylinder block, crankshaft, pistons, cylinder head, and other components. Reference part numbers are given for each item along with other identifying information.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualfjsjjekdkme
1) The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications.
2) It describes the components and operating principles of the fuel injection system, including the fuel tank, lines, filters, pump, and injectors. Diagrams show the components and flow of fuel.
3) Instructions are provided for checking and adjusting aspects of the system, such as setting the accelerator control cable and adjusting the internal timing of the injector pump. Torque specifications are also listed.
Hyster h007 (h12.00 xm europe) forklift service repair manualufjjsejfjksekmem
This document provides instructions for repairing various components of an air brake system, including:
- Air tank repair, including cleaning, releasing air pressure, and installing fittings
- Relief valve and drain valve repair/replacement
- Brake pedal valve removal, disassembly, inspection and installation
- Air chamber removal, disassembly, inspection and reassembly
- Actuator arm removal, inspection and installation
- Brake shoe removal and safety precautions for handling brake linings
It provides detailed steps, diagrams and specifications to guide the repair of these parts in order to ensure proper functioning of the air brake system. Safety warnings are included throughout to prevent injury when working on pressurized components.
Kobelco 230 srlc 3 hydraulic excavator service repair manualudfjjsjekdkdmm
This document contains sections from a shop manual for a hydraulic excavator, including:
1. An overview of the manual's 7 chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and installing optional attachments.
2. Detailed instructions and diagrams for removing and installing components like the upper frame, swing motor unit, swivel joint, and hydraulic pump.
3. Exploded views and specifications for parts like caps, bolts, hoses, and other components.
The manual provides thorough technical information to guide maintenance, repairs, and disassembly/reassembly of the excavator's various systems and components.
Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)fjsjekkmdmme
The document provides instructions for removing and installing various components of an excavator. It describes removing the torque converter cooler assembly which includes disconnecting tubes and hoses, draining oil, and removing mounting bolts. It also describes installing the assembly in reverse order and refilling with oil. Similarly, it provides removal and installation instructions for other assemblies like the fuel injection pump, water pump, turbocharger, and cylinder head.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, seals, springs, pistons, plates, valves, and other internal parts. Detailed illustrations accompany each step to show how to access and remove each component safely. Personal injury warnings are included where parts under spring tension could cause harm.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualfjsjjekdkme
This document provides specifications for a Massey Ferguson MF 362 N tractor intended for the Japanese market only. It includes detailed parts lists and descriptions for the engine, cylinder block, crankshaft, pistons, cylinder head, and other components. Reference part numbers are given for each item along with other identifying information.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualfjsjjekdkme
1) The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications.
2) It describes the components and operating principles of the fuel injection system, including the fuel tank, lines, filters, pump, and injectors. Diagrams show the components and flow of fuel.
3) Instructions are provided for checking and adjusting aspects of the system, such as setting the accelerator control cable and adjusting the internal timing of the injector pump. Torque specifications are also listed.
Hyster h007 (h12.00 xm europe) forklift service repair manualufjjsejfjksekmem
This document provides instructions for repairing various components of an air brake system, including:
- Air tank repair, including cleaning, releasing air pressure, and installing fittings
- Relief valve and drain valve repair/replacement
- Brake pedal valve removal, disassembly, inspection and installation
- Air chamber removal, disassembly, inspection and reassembly
- Actuator arm removal, inspection and installation
- Brake shoe removal and safety precautions for handling brake linings
It provides detailed steps, diagrams and specifications to guide the repair of these parts in order to ensure proper functioning of the air brake system. Safety warnings are included throughout to prevent injury when working on pressurized components.
Kobelco 230 srlc 3 hydraulic excavator service repair manualudfjjsjekdkdmm
This document contains sections from a shop manual for a hydraulic excavator, including:
1. An overview of the manual's 7 chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and installing optional attachments.
2. Detailed instructions and diagrams for removing and installing components like the upper frame, swing motor unit, swivel joint, and hydraulic pump.
3. Exploded views and specifications for parts like caps, bolts, hoses, and other components.
The manual provides thorough technical information to guide maintenance, repairs, and disassembly/reassembly of the excavator's various systems and components.
Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)fjsjekkmdmme
The document provides instructions for removing and installing various components of an excavator. It describes removing the torque converter cooler assembly which includes disconnecting tubes and hoses, draining oil, and removing mounting bolts. It also describes installing the assembly in reverse order and refilling with oil. Similarly, it provides removal and installation instructions for other assemblies like the fuel injection pump, water pump, turbocharger, and cylinder head.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, seals, springs, pistons, plates, valves, and other internal parts. Detailed illustrations accompany each step to show how to access and remove each component safely. Personal injury warnings are included where parts under spring tension could cause harm.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, seals, springs, pistons, plates, valves and other internal parts. Detailed illustrations accompany each step to show how to remove the individual pieces in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored hydraulic pressure or released spring forces during disassembly.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, plates, gears, valves, springs, seals, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are provided due to potential spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...pfiskdmjekm
The document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored hydraulic pressure or released spring forces during disassembly.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjjsjefkskemm
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fhjsjkdmemm
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using several tools and careful handling of parts to avoid injury from released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fhjsjejfjskekemm
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjsekdemmd
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...udfjjdjkskkemmd
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using several tools like pliers, ring pliers, a spring compressor, slide hammer puller, and press. Safety precautions are also noted regarding hydraulic pressure, contained fluids, and released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fujsjjfeskekmm
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using various tools to compress, remove, or release components. Safety precautions are provided regarding hydraulic pressure, contained fluids, and released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjjskekdmem
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides a removal and disassembly procedure for a main hydraulic pump on excavator models 320D2. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. Several specialized tools are required. Disassembly of the pump itself involves an additional 31 steps to dismantle internal components like pistons, springs, seals and bearings. Cleanliness is emphasized to prevent contamination of hydraulic systems.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. Key parts that are disassembled include the pump control, head, seals, port plates, and internal orifices and bearings. Cleanliness during the process is emphasized to prevent contaminating the hydraulic system.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f85 fgexl tractor service r...udfjjjskekmdm
This document provides component part numbers and descriptions for engine repairs and replacements. It includes kits for replacing engine parts between specific serial numbers, as well as individual replacement parts like pistons, rods, bearings, gaskets, plugs, and other engine components. Repair codes indicate whether components should be replaced or overhauled.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f80 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and technical specifications for components of Perkins diesel engines. It includes items like cylinders, crankshafts, pistons, rods, valves, heads, pumps, and other engine parts. Repair and replacement procedures are indicated for some components, with time estimates provided. Serial numbers and engine models are referenced for applicability.
More Related Content
Similar to Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, seals, springs, pistons, plates, valves and other internal parts. Detailed illustrations accompany each step to show how to remove the individual pieces in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored hydraulic pressure or released spring forces during disassembly.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, plates, gears, valves, springs, seals, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are also provided due to potential spring forces.
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble all individual components of the pump. These include removing bolts, seals, gears, plates, valves, springs, pistons, bearings, and other internal parts. Disassembly requires marking parts for reinstallation and using various tools to compress springs and remove retaining rings. Personal injury precautions are provided due to potential spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...pfiskdmjekm
The document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored hydraulic pressure or released spring forces during disassembly.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjjsjefkskemm
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fhjsjkdmemm
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using several tools and careful handling of parts to avoid injury from released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fhjsjejfjskekemm
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjsekdemmd
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...udfjjdjkskkemmd
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using several tools like pliers, ring pliers, a spring compressor, slide hammer puller, and press. Safety precautions are also noted regarding hydraulic pressure, contained fluids, and released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fujsjjfeskekmm
This document provides instructions for disassembling the piston pump (swing) of a M313C wheeled excavator. It lists 19 required tools and provides 42 detailed steps to disassemble the various components of the pump. These include removing retaining rings, springs, seals, plates, ports, valves, gears, pistons, shafts, bearings, and covers. Dismantling the pump involves using various tools to compress, remove, or release components. Safety precautions are provided regarding hydraulic pressure, contained fluids, and released spring forces.
Caterpillar cat m313 c wheeled excavator (prefix bdr) service repair manual (...fjjskekdmem
The document provides instructions for disassembling the piston pump (swing) of a Caterpillar M313C wheeled excavator. It lists 49 steps to fully disassemble the pump. These include removing bolts, seals, springs, plates, and other individual parts from the housing, head, barrel assembly, and other pump components. Detailed illustrations accompany each step to show the specific parts and order of disassembly. Safety notices are included to warn of potential hazards like stored spring energy during the process.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides a removal and disassembly procedure for a main hydraulic pump on excavator models 320D2. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. Several specialized tools are required. Disassembly of the pump itself involves an additional 31 steps to dismantle internal components like pistons, springs, seals and bearings. Cleanliness is emphasized to prevent contamination of hydraulic systems.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. The document is intended to guide maintenance technicians in properly servicing the excavator's hydraulic system.
This document provides removal and disassembly procedures for a 320D2 excavator's main hydraulic pump. It outlines 18 steps to remove the pump, including draining fluids, disconnecting hoses and harnesses, and removing mounting hardware. It then lists 31 additional steps to fully disassemble the pump and its components, requiring various specialized tools. Key parts that are disassembled include the pump control, head, seals, port plates, and internal orifices and bearings. Cleanliness during the process is emphasized to prevent contaminating the hydraulic system.
Similar to Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up) (20)
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f85 fgexl tractor service r...udfjjjskekmdm
This document provides component part numbers and descriptions for engine repairs and replacements. It includes kits for replacing engine parts between specific serial numbers, as well as individual replacement parts like pistons, rods, bearings, gaskets, plugs, and other engine components. Repair codes indicate whether components should be replaced or overhauled.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f80 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and technical specifications for components of Perkins diesel engines. It includes items like cylinders, crankshafts, pistons, rods, valves, heads, pumps, and other engine parts. Repair and replacement procedures are indicated for some components, with time estimates provided. Serial numbers and engine models are referenced for applicability.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f75 fgexl tractor service r...udfjjjskekmdm
This document provides component part information for the repair and replacement of engine parts. It includes lists of components with identification numbers, replacement part numbers, and other technical specifications. Components listed include pistons, rods, crankshafts, pumps, gears, valves, plugs, gaskets and other engine parts. Replacement part kits and overhaul kits are also specified for various engine components.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f70 fge tractor service rep...udfjjjskekmdm
This document contains parts lists and repair instructions for engine components. It lists individual parts, part numbers, quantities needed and repair/replacement instructions. It provides details on repairs, overhauls and replacements for the engine, including the cylinder head, crankshaft, pistons, valves, camshaft and other internal components.
Mc cormick f top restyling (2010 ) - rp55 - f100gexl tractor service repair ...udfjjjskekmdm
This document provides parts information for various engine components. It includes descriptions of parts, part numbers, serial number ranges and replacement part numbers. Images show diagrams of engine assemblies and components with corresponding part numbers and other technical specifications. The document also indicates if parts are for replacement or are not serviced individually.
Komatsu h185 s hydraulic shovel service repair manual (sn 6111)udfjjjskekmdm
This shop manual provides proprietary information for maintaining and repairing the Komatsu H185S hydraulic shovel. It describes the continuous improvement process used by Komatsu to update their products and documentation. Users are advised to check with their distributor for the latest revision of the manual, as revisions may be made without notice due to Komatsu's ongoing research and development efforts.
Komatsu d575 a 2 dozer bulldozer service repair manual (sn 10001 and up)udfjjjskekmdm
This shop manual provides maintenance and repair instructions for the D575A-2 machine model. The manual contains information on machine structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. It summarizes that the D575A-2 mounts the SA12V170-1 engine and refers technicians to the 12V170-1 Series Engine Shop Manual for engine details. The document provides safety precautions and instructions for removing and installing components like the power train oil cooler assembly, hydraulic cooler assembly, and fuel injection pump assemblies.
Komatsu d65 wx 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 wx 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, component diagrams, maintenance procedures, troubleshooting guides, and other technical details. Serial numbers for the models start at 69001. The document is divided into sections covering topics like specifications, engine and cooling systems, power train, undercarriage, hydraulic and electrical systems, and testing and troubleshooting procedures.
Komatsu d65 wx 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which has a SA6D125E-3 engine. It lists 14 steps for removal, including disconnecting wiring, removing hoses and pipes, and taking off covers. Special tools are required for safely removing the fuel supply pump.
Komatsu d65 px 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
This document provides a table of contents for a shop manual covering a bulldozer including models D65EX-16, D65PX-16, and D65WX-16. The table of contents lists sections on specifications and technical data, engine and cooling systems, power train, undercarriage, frames, and hydraulic systems. It includes subsections on components such as transmissions, valves, pumps, and motors. Serial numbers for the models are provided starting from 80001.
Komatsu d65 px 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and service information for Bulldozer models D65EX-15E0, D65PX-15E0, and D65WX-15E0, including serial numbers 69001 and up. It contains sections on specifications, structure and function, maintenance standards, testing and adjusting procedures, and troubleshooting. The document is organized into multiple sections covering various systems of the bulldozers.
Komatsu d65 px 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing mounting hardware and high pressure pipes, and using special tools to extract the pump from the engine case. Workers are advised to take safety precautions and release fuel pressure before performing these tasks.
Komatsu d65 px 12 dozer bulldozer service repair manual sn 65275 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator. It contains general safety precautions and procedures for testing, disassembly, assembly, and maintenance. The document summarizes how to remove and install the fuel supply pump assembly and nozzle holder assembly, including disconnecting wiring and piping, loosening mounting hardware, and reversing steps for installation. Proper torque specifications are listed for reinstalling components.
Komatsu d65 ex 16 dozer bulldozer service repair manual sn 80001 and upudfjjjskekmdm
The document is a shop manual that provides specifications, maintenance procedures, and troubleshooting information for Bulldozer models D65EX-16, D65PX-16, and D65WX-16. It contains sections on the engine and cooling system, power train, undercarriage, hydraulic system, electrical system, and troubleshooting codes. The manual includes diagrams, specifications, maintenance standards, and step-by-step instructions for repairs and adjustments.
Komatsu d65 ex 15e0 dozer bulldozer service repair manual sn 69001 and upudfjjjskekmdm
This document provides specifications and maintenance information for Bulldozer models D65EX, D65PX, and D65WX-15E0. It includes specifications, dimensions, weights, lubricant types, and sections covering the engine/cooling systems, power train, undercarriage, hydraulic system, electrical system, and troubleshooting procedures. Serial numbers for the models start at 69001 and up. The document contains diagrams, specifications, testing and maintenance procedures to service these bulldozer models.
Komatsu d65 ex 15 dozer bulldozer service repair manual sn 67001 and upudfjjjskekmdm
This shop manual provides instructions for servicing a Komatsu D65-15 bulldozer. It contains sections on structure and maintenance standards, testing and adjusting, disassembly and assembly, and other topics. The document excerpt describes removing and installing the fuel supply pump assembly of the D65-15, which involves disconnecting fuel lines and electrical connectors, removing covers and pipes, and taking out the pump. Proper safety precautions are emphasized, such as releasing fuel pressure, wearing protective equipment, and having an assistant when working on rotating parts.
Komatsu d65 ex 12 dozer bulldozer service repair manual sn 65209 and upudfjjjskekmdm
1) This shop manual provides instructions for servicing a Komatsu D65EX/PX-12 excavator.
2) The D65EX/PX-12 uses the SA6D125E-3 engine, with engine service details covered in a separate manual.
3) Proper safety precautions must be followed when servicing equipment, including the use of protective equipment and blocking of moving parts.
John deere 6200 tractors service repair technical manual (tm4523)udfjjjskekmdm
The document provides instructions for assembling and repairing the creeper transmission for tm4523 tractors. It details installing components like connecting rings, snap rings, gears, bearings, and shift collars. Specifications are provided for measurements and torque values. The final section covers general repair procedures for the range transmission, emphasizing cleanliness and care when handling precision machined parts.
John deere 6200 tractors service repair technical manual (tm4493)udfjjjskekmdm
This document provides instructions for adjusting the cone point on differentials for 6100 to 6600 tractors. It involves measuring specific dimensions, calculating the required spacer washer thickness, and selecting the appropriate washers. The final section lists some special tools needed for tasks like tilting the cab, supporting the tractor during wheel removal, and removing/installing shafts.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker Jamieson
Komatsu d475 a 2 dozer bulldozer service repair manual (sn 10201 and up)
1. D475A-2
MACHINE MODEL SERIAL No.
D475A-2 10201 and up
l This shop manual may contain attachments and optional equipment that are not
available in your area. Please consult your local Komatsu distributor for those items
you may require.
Materials and specifications are subject to change without notice.
l D475A-2 mount the SA12Vl40-1 engine.
For details of the engine, see the 12V140-1 Series Engine Shop Manual.
(Q1995KW*U
All Rights Reserved
09-95(01)01301 00&l
4. REMOVAL OF TORQUE REMOVAL OF FUEL INJECTION
CONVERTER COOLER PUMP ASSEMBLY (LEFT,
ASSEMBLY RIGHT)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Remove radiator top cover.
Remove underguard.
* Sling the underguard cover, remove the
mounting bolts, then lower slowly and
open.
Drain oil.
* Remove the drain plug and drain the oil
from the torque converter cooler.
Disconnect tube (1). (See Fl)
Disconnect hose (2). (See F2)
A Fix the fan with rope to prevent it from
turning, and take steps to make sure that
the engine cannot be started.
Disconnect bracket (3). (See F3)
* Disconnect the bracket at the cooler end.
Remove windbreak plate (4). (See F4)
Remove cap (5). (See F4)
Remove torque converter cooler assembly
(6). (See F5)
&Ikg Torque converter cooler assembly:
See Weight Table
t Remove the torque converter assembly
on the opposite side in the same way.
INSTALLATION OF TORQUE INSTALLATION OF FUEL
CONVERTER COOLER INJECTION PUMP ASSEMBLY
ASSEMBLY (LEFT, RIGHT)
. Carry out installation in the reverse order to
removal.
. Refill with oil
Add engine oil to the powertrain oil pan to the
specified level.
It
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Close the fuel supply valve.
Remove fuel strainer (I). (Left side fuel injec-
tion pump only) (See F6)
Ir Remove the mounting bolts of bracket (2),
andmovethefuelstrainerassemblytothe
side.
Remove injection pump coupling cover.
Remove fuel control rod.
Disconnect lubrication tube (3). (See F7)
Disconnect hose (4) for feed pump. (See F7)
Disconnect tubes (5) and (6). (See F7)
Disconnect fuel hose (7). (See F7)
Disconnect fuel injection tube (8). (See F7)m
Remove injection pump mounting bolts (9).
(See F7)
Remove coupling lock bolt (IO). (See F7) m
Remove injection pump assembly (I I). (See
F7) m
* Becareful nottolosethecoupling key,and
keep it in a safe place.
& kg Injection pump assembly:
See Weight Table
. Carry out installation in the reverse order to
removal.
m m Sleeve nut:
See Tightening Torques and
Standard Values Table
m Qa Coupling lock bolt :
See Tightening Torques and
Standard Values Table
m. Adjust the injection timing.
For details, see TESTING AND
ADJUSTING.
30-24
0
6. REMOVAL OF WATER PUMP
ASSEMBLY
1.
2.
3.
4.
Drain cooling water.
:w : See Lubricant and Coolant Table
Remove corrosion resistor (I). (See Fl)
Disconnect piping. (See Fl)
I) Disconnect bypass tube (2). (See Fl)
2) Disconnect aftercooler inlet tube (3). (See
Fl)
3) Disconnect brake cooler outlet tube (4).
(See Fl)
4) Disconnect engine inlet tube (5). (See Fl)
5) Disconnect bypass tube (6). (See Fl)
6) Disconnect water pump inlet tube (7). (See
Fl)
Remove water pump assembly (8). (See Fl)
INSTALLATION OF WATER
PUMP ASSEMBLY
. Carry out installation in the reverse order to
removal.
. Refilling with water
* Add water to the specified level, and run
the engine to circulate the water through
the system. Then check the water level
again.
REMOVAL OF TURBOCHARGER
ASSEMBLY
1. Remove muffler assembly (I). (See F2)
2. Remove exhaust connector (2). (See F2)
3. Remove intake connector (3). (See F2)
4. Disconnect oil supply tube (4). (See F2)
5. Disconnect drain tube (5). (See F2)
6. Remove turbocharger assembly (6). (See F2)
* Disconnect hose, and remove the
turbocharger assembly.
* Remove the turbocharger assembly on
the opposite side in the same way.
INSTALLATION OF
TURBOCHARGER ASSEMBLY
. Carry out installation in the reverse order to
removal.
m
m Turbocharger mounting nut :
2See Tightening Torques and z
Standard Values Table Q)
z
30-26
0
8. REMOVAL OF AFTERCOOLER REMOVAL OF NOZZLE HOLDER
CORE ASSEMBLY ASSEMBLY
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
Drain cooling water.
Remove exhaust pipe and engine hood.
For details, see REMOVAL OF ENGINE
ASSEMBLY.
Remove muffler assembly (1). (See Fl)
Sr Remove the muffler bracket.
Remove air cleaner assembly (2). (See Fl)
* Remove the air cleaner bracket.
Remove intake connector (3). (See F2)
Disconnect electrical intake air heater wiring
(4). (See F2)
Disconnect cooling water piping (51, (61, (7),
and (8). (See F3, F4, F5)
Remove connector (9). (See F5)
Remove cover (IO). (See F5)
Remove aftercooler core assembly (II). (See
F5)
INSTALLATION OF
AFTERCOOLER CORE
ASSEMBLY
. Carry out installation in the reverse order to
removal.
. Refilling with water
Add water to the specified level, and run the
engine to circulate the water through the
system. Then check the water level again.
1.
2.
3.
4.
5.
Remove cover (I ). (See F6)
Disconnect fuel injection piping (2). (See F6)
/33tl/
Remove connection (3). (See F7) m
Remove holder (4). (See F7) m
Remove nozzle holder assembly (5). (See F8)
m
* Screw in the bolts, and using a lever, pull
out.
* Check that there is a gasket fitted to the tip
of the nozzle holder.
* Mark the nozzle holder assemblies with
the cylinder number, and keep them in a
safe place to prevent damage to the tips.
INSTALLATION OF NOZZLE
HOLDER ASSEMBLY
. Carry out installation in the reverse order to
removal.
m
m Sleeve nut :
See Tightening Torques and
Standard Values Table
m
W Connection :
See Tightening Torques and
Standard Values Table
W Locknut:
See Tightening Torques and
Standard Values Table
m
Ir Fit the spherical washer to the bolt and
install.
m Holder mounting bolt :
See Tightening Torques and
Standard Values Table
m
Ir Clean the nozzle holder assembly mount
before installing.
30-28
a
10. REMOVAL OF CYLINDER HEAD
ASSEMBLY
A.Disconnect the cable from the negative (-1
1.
2.
3.
4.
5.
6.
7.
a.
9.
10.
11.
12.
13.
14.
15.
terminal of the battery.
Drain cooling water.
18. Remove cylinder head assembly (24). (See F9)
n
Remove exhaust pipe and engine hood.
For details, see REMOVAL OF ENGINE
ASSEMBLY.
INSTALLATION OF CYLINDER
HEAD ASSEMBLY
Remove muffler assembly (I ). (See Fl)
* Remove the muffler bracket.
Remove air cleaner assembly (2). (See Fl)
j, Remove the air cleaner bracket.
Remove turbocharger assembly (3). (See F2)
For details, see REMOVAL OF TURBO-
CHARGER ASSEMBLY.
l Carry out installation in the reverse order to
removal.
m
m Sleeve nut :
See Tightening Torques and
Standard Values Table
m
Ir Checkthatthe balloftheadiustmentscrew
Remove exhaust manifold assembly (4). (See is fixed securely in the socket of the
F2) rod.
Remove intake manifold assembly (for left
bank). (See F3)
I) Disconnect tubes (5) and (6) for air
m Rocker arm mountino bolt :
m
*
m
*
i)
ii)
iii)
iv)
See Tightening Torques
Standard Values Table
compressor.
2) Disconnect tube (7) for aftercooler.
3) Disconnect 2 heater relay wires (8).
4) Remove intake manifold assembly (9).
5) Remove electrical intake air heater (IO).
Remove intake manifold assembly (for right
bank). (See F4)
1) Disconnectelectrical intakeairheaterwire
Checkthatthe push rod isfixed securely in
the cam follower.
(II).
2) Disconnect tubes (12) and (13) for
aftercooler.
3) Remove intake manifold assembly (14).
4) Remove electrical intake air heater (15).
Disconnect fuel injection piping (16). (See F5)
m
Adjust the crosshead as follows.
Loosen the locknut, and turn back the
adjustment screw.
Hold the top surface of the crosshead
lightly, and screw in the adjustment screw.
After the adjustment screw contacts the
valve stem, tighten it a further 20”.
Tighten the locknut to hold the screw in
position.
Disconnect spill tube (17). (See F5)
Disconnect air vent tube (18). (See F5)
Remove head cover (191. (See F5)
Remove rocker arm (20). (See F6) m
Remove push rod (21). (See F7) m
Remove crosshead (22). (See F7) m
m Locknut :
See Tightening Torques and
Standard Values Table
m
* Adjust the valve clearance.
For details, see TESTING AND ADJUST-
ING, Adjusting valve clearance.
m Rocker arm, screw, locknut :
See Tightening Torques and
Standard Values Table
m
m Cylinder head mounting bolt :
See Tightening Torques and
Standard Values Table
16. Remove nozzle holder assembly.
* For details, see REMOVAL OF NOZZLE
HOLDER ASSEMBLY.
17. Remove rocker housing (23). (See F8) m
push
and
30-30
0
12. REMOVAL OF FUEL TANK
ASSEMBLY
1. Disconnect hose (1). (See Fl)
* Before disconnecting the hose, close the
fuel valve.
INSTALLATION OF FUEL TANK
ASSEMBLY
l Carry out installation in the reverse order to
removal.
2. Remove bracket (2). (See Fl)
3. Remove wiring connector (3). (See Fl)
4. Remove clamp of drain hose (4). (See Fl)
5. Disconnect hoses (5) and (6). (See F2)
6. Remove fuel tank assembly (7). (See F3)
& kg Fuel tank assembly:
See Weight Table
30-32
a
13. Fl
3
F2
I 4 I j 198FO241'
IwfilIIIll 198FO2412
30-33
0
14. REMOVAL OF RADIATOR
ASSEMBLY
1. Drain cooling water.
10. Remove left and right isolators (13). (See F5)
2. Remove cover (I), engine hood (2), and left
and right side covers (3). (See Fl)
+ Liftofftheenginehoodandthesidecovers.
& kg Engine hood : See Weight Table
& kg Side cover : See Weight Table
3. Remove underguard (4). (See F2)
* Settransmissionjack 0 underthecenter
of the underguard, and lower the
transmission jack slowly to remove the
underguard.
11. Remove left and right brackets (14). (See F6)
PIkg Underguard : See Weight Table
4. Remove underguard (5). (See F2)
* Fit a sling around the underguard, lower
slowly, and open the underguard.
5. Disconnect wiring connector (6). (See F3) 12. Remove left and right caps (15). (See F7)
6. Disconnect hose (7) and tube (8). (See F3)
7. Remove condenser assembly (9). (See F3)
* Disconnect the hose of receiver tank (IO),
and remove the condenser assembly.
13. Remove radiator assembly (16). (See F8)
Sr Raise the radiator assembly carefully, and
be careful not to damage the core.
&?Ikg Radiator assembly :
See Weight Table
8. Disconnect tube (II). (See F4)
9. Disconnect hose (12). (See F4) INSTALLATION OF RADIATOR
ASSEMBLY
. Carry out installation in the reverse order to
removal.
. Refilling with water
Add water to the specified level, and run the
engine to circulate the water through the
system. Then check the water level again.
30-34
a
16. REMOVAL OF RADIATOR
GUARD ASSEMBLY
5. Disconnect wiring connector (6). (See F5)
. See REMOVAL OF RADIATOR ASSEMBLY, and
carry out Steps 1 - 9.
1. Disconnect hose (I). (See Fl)
2. Disconnect hose (2). (See F2)
3. Remove cap (3) and shim (4). (See F3) m
* Check the number and thickness of the
shims, and keep in a safe place.
* Sling the blade cylinder, and run the
engine, retract the piston rod, then secure
the blade cylinder to the holder pin on the
chassis.
+ Remove the cap and shim on the opposite
side, and secure the blade cylinder to the
holder pin on the chassis.
4. Disconnect hose (5). (See F4)
A Stop the engine, and operate the control
levers several times to release the
remaining pressure in the hydraulic piping.
Then loosen the oil filler cap slowly to
release the pressure inside the hydraulic
tank.
6. Remove pin (7). (See F6)
* Sling the radiator guard assembly, and
remove the lock bolt, then using tool A,
push out the pin.
* Push out the pin on the opposite side in
the same way. ,
7. Remove pin (8). (See F7)
* Using tool A, pull out the pin.
8. Remove radiator guard assembly (9). (See F8)
* Check that all the wiring and piping has
been removed before removing the
radiator guard assembly.
& kg Radiator guard assembly :
See Weight Table
INSTALLATION OF RADIATOR
GUARD ASSEMBLY
. Carry out installation in the reverse order to
removal.
m
Standard shim thickness : 4 mm
. Refilling with water
Add water to the specified level, and run the
engine to circulate the water through the
system. Then check the water level again.
30-36
0
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. REMOVAL OF FAN DRIVE
PUMP ASSEMBLY
1. Turn over ROPS cab assembly.
* For details, see TURNING OVER ROPS
CAB ASSEMBLY.
2. Remove wiring connector (1). (See Fl)
3. Disconnect hose (2). (See Fl)
4. Remove pump assembly (3). (See Fl)
* Move coupling (41, then remove the pump
assemblytogetherwith suction pipe. (See
Fl)
& kg Pump assembly :
See Weight Table
INSTALLATION OF FAN DRIVE
ASSEMBLY
. Carry out installation in the reverse order to
removal.
REMOVAL OF FAN MOTOR
ASSEMBLY
1.
2.
3.
4.
5.
Drain hydraulic oil from tank.
:_ : See Lubricant and Coolant Table
Remove fan (I). (See F2)
Ir Sling the fan, then using guide bolt @
(Thread dia.=12mm, Pitch=l.75mm),
remove the fan.
&?Ikg Fan : See Weight Table
Disconnect hose (2). (See F3)
Disconnect drain hose (3). (See F4)
* Sling the bracket, tilt the top towards the
front, and disconnect the hose.
Remove fan motor assembly (4). (See F5)
&Ikg Fan motor assembly (including
bracket) : See Weight Table
*
I)
2)
3)
4)
Remove the fan motor assembly from the
bracket as follows.
Remove hose (5) and bracket (6). (See F6)
Remove nut (7). (See F7)
Using puller@, remove pulley (8). (See F8)
Remove fan motor assembly (9) from
bracket. (See F6)
INSTALLATION OF FAN MOTOR
ASSEMBLY
Ir Install the fan motor assembly to the bracket
as follows.
1) Set fan motor assembly (9) to the bracket.
(See F6)
2) Fitthe keytothe motorshaft, install pulley
(8), tighten nut (7), then secure with the
lock plate. (See F7, F8)
+ Tighten the nut to 80- 100 kgm, and if
the lock plate position is not aligned,
turninthetighteningdirectiontoalign.
3) Install bracket (6) and hose (5). (See F6)
. Carry out installation in the reverse order to
removal.
. Refilling with oil z
Addengineoilthroughoilfillertothespecified 2
level, and run the engine to circulate the oil %
through the system. Then check the oil level
again.
Hydraulic tank :
See Lubricant and Coolant Table
30-38
0