This document provides technical specifications for JCB excavators, including noise emissions data, vibration emissions data, and recommended fluids, lubricants and capacities. It consists of specifications for multiple excavator models organized into sections covering noise emissions test conditions and data in 3 tables, vibration emissions test procedures and whole-body and hand-arm vibration data in figures and tables, and recommended fluids including lubricants, coolant, and grease types and capacities in tables.
This document summarizes new and improved functions of SCON controllers for linear servo actuators. Key points include:
1) An offboard tuning function allows increasing actuator load capacity and acceleration/deceleration by automatically setting optimal gain according to the load. It provides benefits such as increasing maximum payload and speed.
2) The controllers now support many major field networks for simple, wire-saving connections to various equipment. Operations can be done by specifying positions or direct numerical values.
3) A new vibration control function suppresses vibration of workpieces attached to the actuator, shortening wait times and reducing cycle times.
New holland w80 c tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w80 c tier 4 compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides maintenance and repair instructions for these components.
New holland w70 c stage iiib compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland w70 wheel loader service repair manualfujsjefskekmm
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
New holland tc5080 combine harvesters service repair manualfujsjefskekmm
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance should only be performed by trained technicians using the proper tools and procedures outlined in the manual. Unauthorized repairs may void warranties.
New holland tc5.90 hillside fpt nef 6 stage iv combine harvester service repa...fujsjefskekmm
This document is a service manual for various combine harvester models. It provides maintenance and repair instructions for the engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and other components. The manual includes an introduction with safety guidelines and a table of contents listing the major vehicle systems and associated part numbers covered.
New holland tc5.90 fpt nef tier 3 combine harvester service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, diagrams and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. Each section number links to detailed information on components and subsystems such as the engine, transmission, hydrostatic drive, steering, cab climate control, threshing drum, cleaning systems, and unloading systems.
This document summarizes new and improved functions of SCON controllers for linear servo actuators. Key points include:
1) An offboard tuning function allows increasing actuator load capacity and acceleration/deceleration by automatically setting optimal gain according to the load. It provides benefits such as increasing maximum payload and speed.
2) The controllers now support many major field networks for simple, wire-saving connections to various equipment. Operations can be done by specifying positions or direct numerical values.
3) A new vibration control function suppresses vibration of workpieces attached to the actuator, shortening wait times and reducing cycle times.
New holland w80 c tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w80 c tier 4 compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides maintenance and repair instructions for these components.
New holland w70 c stage iiib compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland w70 wheel loader service repair manualfujsjefskekmm
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
New holland tc5080 combine harvesters service repair manualfujsjefskekmm
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance should only be performed by trained technicians using the proper tools and procedures outlined in the manual. Unauthorized repairs may void warranties.
New holland tc5.90 hillside fpt nef 6 stage iv combine harvester service repa...fujsjefskekmm
This document is a service manual for various combine harvester models. It provides maintenance and repair instructions for the engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and other components. The manual includes an introduction with safety guidelines and a table of contents listing the major vehicle systems and associated part numbers covered.
New holland tc5.90 fpt nef tier 3 combine harvester service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, diagrams and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. Each section number links to detailed information on components and subsystems such as the engine, transmission, hydrostatic drive, steering, cab climate control, threshing drum, cleaning systems, and unloading systems.
New holland mc35 commercial mower service repair manualfujsjefskekmm
The document is a service manual for New Holland commercial mowers models MC22, MC28, and MC35. It contains sections covering general information, safety, specifications, maintenance and repair of engine, drivetrain, hydraulic and electrical systems. The manual provides technical details and instructions to properly service the mowers.
New holland l234 tier 4 b (final) skid steer loader service repair manual [nh...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
New holland d180 c stage iiib crawler dozer service repair manual (pin nedc18...fujsjefskekmm
This service manual section provides information for removing and installing the engine and crankcase assembly on a D180C crawler dozer. The 6-step removal process involves using lifting equipment to detach the engine from the frame mounts at the front and sides. Proper lifting points and balance of the 631 kg engine are emphasized for safety.
New holland d150 c stage iiib crawler dozer service repair manual (pin nedc15...fujsjefskekmm
This service manual provides information for servicing the following components of a D150C crawler dozer:
- Engine and related systems such as air cleaners, fuel filters, cooling and emissions systems
- Hydrostatic drive system
- Brakes and controls
- Hydraulic systems including cylinders, pumps and valves
- Tracks and track suspension
- Cab climate control and electrical systems
- Dozer blade and tools
- Cab, bodywork and decals
It provides removal and installation instructions as well as specifications for maintenance and repair of these components.
New holland cx5.90 laterale fpt nef 6 tier 4 b stage iv combine harvester ser...fujsjefskekmm
This document is a service manual for several combine models and their engines. It contains an introduction section listing the machine models covered and their engine types. The bulk of the document is a detailed table of contents that lists over 150 individual sections providing service information on the combines' systems and components, including the engine, transmission, hydraulics, steering, climate control, electrical systems, attachments, feeding, and threshing systems.
New holland cr940 combine harvesters service repair manualfujsjefskekmm
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electrics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
New holland c238 tier 4 b (final) compact track loader service repair manual ...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
Case 621 f tier 4 wheel loader service repair manualfujsjefskekmm
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connecting parts. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland br6090 combi service repair manualfujsjefskekmm
This document provides a service manual for a BR6090 COMBI machine. It includes sections on hydraulic, pneumatic, electrical, electronic and other systems. It details components like the secondary hydraulic power system, electrical power system, lighting system, electronic system, lubrication system and more. It also covers the engine and PTO, transmission, process drive, axles, brakes, steering, wheels, frame, and crop processing functions. Torque specifications are provided for hardware.
New holland b100 btc backhoe loader service repair manualfujsjefskekmm
This document contains service manual sections for various backhoe loader models. It includes information on safety rules, maintenance, technical specifications, transmission systems, front axles, and other components. Technical specifications include details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets, tires, and machine dimensions and performance specs. The transmission and front axle sections provide specifications, lubrication instructions, removal/installation procedures, and troubleshooting guides.
New holland b100 blr backhoe loader service repair manualfujsjefskekmm
This document contains service manuals for various backhoe loader models including the B90B, B100B, B110B, and B115B. It includes sections on safety, maintenance, technical specifications, troubleshooting, and repair procedures for components like the transmission, axles, brakes, hydraulics, electrical systems, and attachments. The manuals provide information on lubrication, removal and installation of parts, disassembly and assembly of systems, and repair times for maintenance and repairs.
New holland b95 lr backhoe loader service repair manualfujsjefskekmm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b95 ctc tier 4b (final) tractor loader backhoe service repair manualfujsjefskekmm
This document is a service manual for New Holland tractor loader backhoes that covers specifications, maintenance, and repair procedures. It includes sections on the engine and fuel systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, climate control, electrical systems, front loader/bucket, booms/dippers/buckets, and cab/bodywork. Safety precautions are provided to ensure safe operation and service of the equipment.
Case 121 f xt tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
- The document is a service manual that provides instructions for removing the engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, removing protective covers and grids, and using lifting equipment to extract the engine from the rear of the vehicle. The process involves multiple steps to properly prepare the machine before removing and lowering the engine.
Case 121 f xt tier 4a (interim) compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for Case compact wheel loaders models 121F XT, 121F ZB, 21F XT, 21F ZB, 221F HS, 221F STD, 321F HS, and 321F STD. It provides maintenance instructions and repair procedures for components of the wheel loaders including the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln 322cln excavator (prefix bfk) service repair manual ...fujsjefskekmm
This document provides disassembly instructions for a final drive on a 322C excavator. It outlines 32 steps to fully disassemble the final drive. The steps include removing housing components, gears, carriers, seals, and other parts. Special tools are listed that are required for removal of components. Cleanliness is emphasized during disassembly to prevent dirt entry. Weights of removed parts are provided.
Caterpillar cat 322 c l 322cl excavator (prefix blp) service repair manual (b...fujsjefskekmm
This document provides step-by-step instructions for disassembling various components of a 322C excavator's auxiliary control valve, including the solenoid valve and housing, spool and plug, line relief valve, and load hold check valve. It details removing o-rings, fittings, valves, spools, and other parts. Cleanliness is emphasized to prevent contamination of the hydraulic system during disassembly and reassembly.
Caterpillar cat 322 c l 322cl excavator (prefix bkj) service repair manual (b...fujsjefskekmm
The document provides instructions for installing a cylinder head on a 3126 engine. It describes:
1) Cleaning the cylinder head and cylinder block mating surfaces and installing a new cylinder head gasket.
2) Positioning the cylinder head on the dowels and lowering it onto the cylinder block.
3) Tightening the cylinder head bolts in a specific sequence and torque pattern.
New holland mc35 commercial mower service repair manualfujsjefskekmm
The document is a service manual for New Holland commercial mowers models MC22, MC28, and MC35. It contains sections covering general information, safety, specifications, maintenance and repair of engine, drivetrain, hydraulic and electrical systems. The manual provides technical details and instructions to properly service the mowers.
New holland l234 tier 4 b (final) skid steer loader service repair manual [nh...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
New holland d180 c stage iiib crawler dozer service repair manual (pin nedc18...fujsjefskekmm
This service manual section provides information for removing and installing the engine and crankcase assembly on a D180C crawler dozer. The 6-step removal process involves using lifting equipment to detach the engine from the frame mounts at the front and sides. Proper lifting points and balance of the 631 kg engine are emphasized for safety.
New holland d150 c stage iiib crawler dozer service repair manual (pin nedc15...fujsjefskekmm
This service manual provides information for servicing the following components of a D150C crawler dozer:
- Engine and related systems such as air cleaners, fuel filters, cooling and emissions systems
- Hydrostatic drive system
- Brakes and controls
- Hydraulic systems including cylinders, pumps and valves
- Tracks and track suspension
- Cab climate control and electrical systems
- Dozer blade and tools
- Cab, bodywork and decals
It provides removal and installation instructions as well as specifications for maintenance and repair of these components.
New holland cx5.90 laterale fpt nef 6 tier 4 b stage iv combine harvester ser...fujsjefskekmm
This document is a service manual for several combine models and their engines. It contains an introduction section listing the machine models covered and their engine types. The bulk of the document is a detailed table of contents that lists over 150 individual sections providing service information on the combines' systems and components, including the engine, transmission, hydraulics, steering, climate control, electrical systems, attachments, feeding, and threshing systems.
New holland cr940 combine harvesters service repair manualfujsjefskekmm
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electrics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
New holland c238 tier 4 b (final) compact track loader service repair manual ...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
Case 621 f tier 4 wheel loader service repair manualfujsjefskekmm
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connecting parts. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland br6090 combi service repair manualfujsjefskekmm
This document provides a service manual for a BR6090 COMBI machine. It includes sections on hydraulic, pneumatic, electrical, electronic and other systems. It details components like the secondary hydraulic power system, electrical power system, lighting system, electronic system, lubrication system and more. It also covers the engine and PTO, transmission, process drive, axles, brakes, steering, wheels, frame, and crop processing functions. Torque specifications are provided for hardware.
New holland b100 btc backhoe loader service repair manualfujsjefskekmm
This document contains service manual sections for various backhoe loader models. It includes information on safety rules, maintenance, technical specifications, transmission systems, front axles, and other components. Technical specifications include details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets, tires, and machine dimensions and performance specs. The transmission and front axle sections provide specifications, lubrication instructions, removal/installation procedures, and troubleshooting guides.
New holland b100 blr backhoe loader service repair manualfujsjefskekmm
This document contains service manuals for various backhoe loader models including the B90B, B100B, B110B, and B115B. It includes sections on safety, maintenance, technical specifications, troubleshooting, and repair procedures for components like the transmission, axles, brakes, hydraulics, electrical systems, and attachments. The manuals provide information on lubrication, removal and installation of parts, disassembly and assembly of systems, and repair times for maintenance and repairs.
New holland b95 lr backhoe loader service repair manualfujsjefskekmm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b95 ctc tier 4b (final) tractor loader backhoe service repair manualfujsjefskekmm
This document is a service manual for New Holland tractor loader backhoes that covers specifications, maintenance, and repair procedures. It includes sections on the engine and fuel systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, climate control, electrical systems, front loader/bucket, booms/dippers/buckets, and cab/bodywork. Safety precautions are provided to ensure safe operation and service of the equipment.
Case 121 f xt tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
- The document is a service manual that provides instructions for removing the engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, removing protective covers and grids, and using lifting equipment to extract the engine from the rear of the vehicle. The process involves multiple steps to properly prepare the machine before removing and lowering the engine.
Case 121 f xt tier 4a (interim) compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for Case compact wheel loaders models 121F XT, 121F ZB, 21F XT, 21F ZB, 221F HS, 221F STD, 321F HS, and 321F STD. It provides maintenance instructions and repair procedures for components of the wheel loaders including the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln 322cln excavator (prefix bfk) service repair manual ...fujsjefskekmm
This document provides disassembly instructions for a final drive on a 322C excavator. It outlines 32 steps to fully disassemble the final drive. The steps include removing housing components, gears, carriers, seals, and other parts. Special tools are listed that are required for removal of components. Cleanliness is emphasized during disassembly to prevent dirt entry. Weights of removed parts are provided.
Caterpillar cat 322 c l 322cl excavator (prefix blp) service repair manual (b...fujsjefskekmm
This document provides step-by-step instructions for disassembling various components of a 322C excavator's auxiliary control valve, including the solenoid valve and housing, spool and plug, line relief valve, and load hold check valve. It details removing o-rings, fittings, valves, spools, and other parts. Cleanliness is emphasized to prevent contamination of the hydraulic system during disassembly and reassembly.
Caterpillar cat 322 c l 322cl excavator (prefix bkj) service repair manual (b...fujsjefskekmm
The document provides instructions for installing a cylinder head on a 3126 engine. It describes:
1) Cleaning the cylinder head and cylinder block mating surfaces and installing a new cylinder head gasket.
2) Positioning the cylinder head on the dowels and lowering it onto the cylinder block.
3) Tightening the cylinder head bolts in a specific sequence and torque pattern.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Technical Data
Noise Emissions
334 9821/9700-1 334
Noise Emissions
General
To assist in compliance with European Directives 2000/14/EC and 2005/88/EC, the noise data values for this
type of machine have been provided on the following page(s) and may be used for the assessment of risks
to exposure from noise.
The noise data values shown only apply to CE marked machines.
For information relating to this machine when used with other JCB approved attachments, please refer to the
literature accompanying the attachments.
Table 1. Definition of terms
Term Definition Notes
LpA A-weighted sound pressure level mea-
sured at the operator's station.
Determined in accordance with the test method
defined in ISO 6396 and the dynamic test condi-
tions defined on 2000/14/EC.
LwA Equivalent A-weighted sound power level
emitted by the machine.
Guaranteed equivalent sound power (external
noise) determined in accordance with the dynamic
test conditions defined in 2000/14/EC.
Noise Data
For: JS115, JS130, JS145, .................................................................................................... Page 334
For: JS160, JS180, JS190 ..................................................................................................... Page 334
For: JS200, JS210, JS220, JS235 ......................................................................................... Page 334
(For: JS115, JS130, JS145,)
Table 1. All Machines
Engine rating
(1)
LpA LwA
74kW 72 100
81kW 72 100
(1) Net installed power.
(For: JS160, JS180, JS190)
Table 2.
Engine rating
(1)
LpA LwA
93kW 71 100
97kW 73 100
(1) Net installed power.
(For: JS200, JS210, JS220, JS235)
Table 3.
Engine rating
(1)
LpA LwA
129kW 73 102
(1) Net installed power.
3. Technical Data
Vibration Emissions
335 9821/9700-1 335
Vibration Emissions
General
To assist in compliance with the European Directive 2002/44/EC, the duty specific vibration emission values
for this machine type have been provided on the following page(s) and may be used for the assessment of
risks to exposure from vibration.
Unless otherwise indicated for a specific operating condition, the vibration values are calculated with the
machine equipped with the standard attachments (for example bucket, shovel, fork, etc.) for the respective
operating condition.
The vibration values are calculated from measurements in three perpendicular axes (X, Y and Z). The highest
weighted (RMS (Root Mean Square)) value is used to specify the vibration emission.
The axis upon which the highest weighted (RMS) value occurs is shown on the vibration chart for each of the
machine operating duties, see dominant axis (X, Y or Z).
Figure 362.
Z
X
Y
Exposure to Vibration
Exposure to vibration can be minimised through:
• Selection of the correct size and capacity of machine, equipment and attachments for a particular
application
• Use of a machine equipped with an appropriate seat, keeping the seat maintained and adjusted
• Checks to make sure that the machine is correctly maintained, reporting and correcting any faults
• Steering, braking, accelerating, shifting gears, moving the attachments and load smoothly
• Adjusting the machine speed and travel path to minimise the vibration level
• Keeping the terrain on worksites where the machine works and travels in good condition, removing any
large rocks or obstacles and filling in any ditches and holes
• Choosing routes that avoid rough surfaces and, if this is not possible, drive more slowly to avoid bumping
and jolting
• Travel over longer distances at an adjusted (medium) speed
• Avoiding bad postures, i.e. slumping in your seat, constantly leaning forward or sideways or driving with
your back twisted.
4. Technical Data
Vibration Emissions
336 9821/9700-1 336
Vibration Data
For: JS115, JS130, JS145, .................................................................................................... Page 336
For: JS160, JS180, JS190 ..................................................................................................... Page 337
For: JS330 .............................................................................................................................. Page 337
For: JS200, JS210, JS220, JS235 ......................................................................................... Page 338
For: JS360 .............................................................................................................................. Page 339
(For: JS115, JS130, JS145,)
The whole-body vibration emission under representative operating conditions (according to the intended use)
are shown.
Figure 363.
D1 D2 D3
m/s²A(8)
X XX
0.01
0.19
0.39
X-Z Dominant axis
D1 Machine operating duty: Low idle
D2 Machine operating duty: Excavating
D3 Machine operating duty: Tracking (rough terrain)
The whole-body vibration emission calculated in accordance with ISO 2631-1:1997 for this machine type is
0.19m/s² normalised to an 8h reference period [A(8)] and based upon a test cycle defined in SAE J1166.
The hand-arm vibration calculated in accordance with the dynamic test conditions defined in ISO 5349-2: 2001
does not exceed 2.5m/s².
The errors bars are due to variations in vibration emissions due to measurement uncertainty (50% in
accordance with EN 12096:1997).
5. Technical Data
Vibration Emissions
337 9821/9700-1 337
(For: JS160, JS180, JS190)
Figure 364.
0.01
0.17
0.64
m/s²A(8)
D1 D2 D3
Y X Z
X-Z Dominant axis
D1 Machine operating duty: Low idle
D2 Machine operating duty: Excavating
D3 Machine operating duty: Tracking (rough terrain)
The whole-body vibration emission under representative operating conditions (according to the intended use)
are shown. Refer to Figure 364.
The whole-body vibration emission calculated in accordance with ISO 2631-1:1997 for this machine type is
0.17m/s² normalised to an 8h reference period [A(8)] and based upon a test cycle defined in SAE J1166.
The hand-arm vibration calculated in accordance with the dynamic test conditions defined in ISO 5349-2: 2001
does not exceed 2.5m/s².
The errors bars are due to variations in vibration emissions due to measurement uncertainty (50% in
accordance with EN 12096:1997).
(For: JS330)
The whole-body vibration emission under representative operating conditions (according to the intended use)
are shown.
6. Technical Data
Vibration Emissions
338 9821/9700-1 338
Figure 365.
D3D2
0.19
0.34
0.03
m/s²A(8)
D1
ZY X
X-Z Dominant axis
D1 Machine operating duty: Low idle
D2 Machine operating duty: Excavating
D3 Machine operating duty: Tracking (rough terrain)
The whole-body vibration emission calculated in accordance with ISO 2631-1:1997 for this machine type is
0.19m/s² normalised to an 8h reference period [A(8)] and based upon a test cycle defined in SAE J1166.
The hand-arm vibration calculated in accordance with the dynamic test conditions defined in ISO 5349-2: 2001
does not exceed 2.5m/s².
The errors bars are due to variations in vibration emissions due to measurement uncertainty (50% in
accordance with EN 12096:1997).
(For: JS200, JS210, JS220, JS235)
Figure 366.
XY
0.37
0.24
D1 D2 D3
0.07
Z
m/s²A(8)
X-Z Dominant axis
D1 Machine operating duty: Low idle
D2 Machine operating duty: Excavating
D3 Machine operating duty: Tracking (rough terrain)
The whole-body vibration emission under representative operating conditions (according to the intended use)
are shown. Refer to Figure 366.
7. Technical Data
Vibration Emissions
339 9821/9700-1 339
The whole-body vibration emission calculated in accordance with ISO 2631-1:1997 for this machine type is
0.24m/s² normalised to an 8h reference period [A(8)] and based upon a test cycle defined in SAE J1166.
The hand-arm vibration calculated in accordance with the dynamic test conditions defined in ISO 5349-2: 2001
does not exceed 2.5m/s².
The errors bars are due to variations in vibration emissions due to measurement uncertainty (50% in
accordance with EN 12096:1997).
(For: JS360)
The whole-body vibration emission under representative operating conditions (according to the intended use)
are shown.
Figure 367.
0.02
0.25
0.37
D3D2
m/s²A(8)
D1
ZY X
X-Z Dominant axis
D1 Machine operating duty: Low idle
D2 Machine operating duty: Excavating
D3 Machine operating duty: Tracking (rough terrain)
The whole-body vibration emission calculated in accordance with ISO 2631-1:1997 for this machine type is
0.25m/s² normalised to an 8h reference period [A(8)] and based upon a test cycle defined in SAE J1166.
The hand-arm vibration calculated in accordance with the dynamic test conditions defined in ISO 5349-2: 2001
does not exceed 2.5m/s².
The errors bars are due to variations in vibration emissions due to measurement uncertainty (50% in
accordance with EN 12096:1997).
8. Technical Data
Fluids, Lubricants and Capacities
340 9821/9700-1 340
Fluids, Lubricants and Capacities
General
For: JS115, JS130, JS145, .................................................................................................... Page 340
For: JS160, JS180, JS190 ..................................................................................................... Page 340
For: JS330, JS360 ................................................................................................................. Page 341
For: JS200, JS210, JS220, JS235 ......................................................................................... Page 342
(For: JS115, JS130, JS145,)
JCB recommend that you use the JCB lubricants shown as they have been verified by JCB for use on JCB
machines. However, you could use other lubricants that are equivalent to the JCB standards and quality or
offer the same machine component protection.
Table 1. Fluids, Lubricants and Capacities
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
Fuel Tank 253L Diesel - -
Above -10°C (14°F): JCB Engine Oil
EP 15W/40
4001/1805 20LEngine (Oil)
(2)
20.4L
-20°C (-4°F) to 50°C (122°F): JCB
Cold Climate Engine Oil EP 5W40
4001/2705 20L
Cooling System 19.7L JCB Antifreeze HP/Coolant 4006/1120 20L
Track Gearbox
(each)
3.5L JCB HD90 Gear Oil 4001/0305 20L
Slew Gearbox 2.2L JCB HD90 Gear Oil 4000/0305 20L
Track Rollers and
Idler Wheels
JCB HD90 Gear Oil 4000/0305 20L
Recoil Spring Cylin-
der
JCB Special HP Grease 4003/2017 0.4kg
JCB Hydraulic Fluid HP32-20°C
(-4°F) to 15°C (59°F)
4002/1024 200L
JCB Hydraulic Fluid HP46-10°C
(14°F) to 30°C (86°F)
4002/0803 200L
Hydraulic System 124L
JCB Hydraulic Fluid HP680°C (32°F)
to 40°C (104°F)
4002/0701 200L
Slew Ring Bearings 0.06kg JCB Special HP Grease 4003/2017 0.4kg
Slew Ring Gear
Teeth
11kg JCB Special HP Grease 4003/2006 12.5kg
All Other Grease As required JCB Special HP Grease 4003/2017 0.4kg
(1) For information about the different container sizes that are available (and their part numbers), contact your
local JCB dealer.
(2) Do not use ordinary engine oil.
(For: JS160, JS180, JS190)
JCB recommend that you use the JCB lubricants shown as they have been verified by JCB for use on JCB
machines. However, you could use other lubricants that are equivalent to the JCB standards and quality or
offer the same machine component protection.
Table 2. Fluids, Lubricants and Capacities
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
Fuel Tank 253L Diesel - -
Engine (Oil)
(2)
20.4L -10°C (14°F) to 50°C (121.9°F): JCB
Engine Oil EP 15W/40
4001/1805 20L
9. Technical Data
Fluids, Lubricants and Capacities
341 9821/9700-1 341
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
-20°C (-4°F) to 50°C (122°F): JCB
Cold Climate Engine Oil EP 5W40
4001/2705 20L
Cooling System 19.7L JCB Antifreeze HP/Coolant 4006/1120 20L
Track Gearbox
(each)
4.4L JCB HD90 Gear Oil 4001/0301 5L
Slew Gearbox 6L JCB HD90 Gear Oil 4000/0305 20L
Track Rollers and
Idler Wheels
JCB HD90 Gear Oil 4000/0305 20L
Recoil Spring Cylin-
der
JCB Special HP Grease 4003/2017 0.4kg
JCB Hydraulic Fluid HP32-20°C
(-4°F) to 15°C (59°F)
4002/1024 200L
JCB Hydraulic Fluid HP46-10°C
(14°F) to 30°C (86°F)
4002/0803 200L
Hydraulic System 142L
JCB Hydraulic Fluid HP680°C (32°F)
to 40°C (104°F)
4002/0701 200L
Slew Ring Bearings 0.075kg JCB Special HP Grease 4003/2017 0.4kg
Slew Ring Gear
Teeth
11kg JCB Special HP Grease 4003/2006 12.5kg
All Other Grease As required JCB Special HP Grease 4003/2006 12.5kg
(1) For information about the different container sizes that are available (and their part numbers), contact your
local JCB dealer.
(2) Do not use ordinary engine oil.
(For: JS330, JS360)
JCB recommend that you use the JCB lubricants shown as they have been verified by JCB for use on JCB
machines. However, you could use other lubricants that are equivalent to the JCB standards and quality or
offer the same machine component protection.
Table 3. Fluids, Lubricants and Capacities
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
Fuel Tank 590L Diesel - -
Engine (Oil)
(2)
25L JCB Ultimate Performance 15W40
API CJ-4, ACEA E6, E9, JASO
DH-2
(3)
4001/2905 20L
Cooling System 45L JCB Antifreeze HP/Coolant 4006/1120 20L
Track Gearbox
(each)
5L JCB HD90 Gear Oil 4001/0301 5L
Slew Gearbox 14.5L JCB HD90 Gear Oil 4000/0305 20L
Track Rollers and
Idler Wheels
JCB HD90 Gear Oil 4000/0305 20L
Recoil Spring Cylin-
der
JCB Special HP Grease 4003/2017 0.4kg
JCB Hydraulic Fluid HP32-20°C
(-4°F) to 15°C (59°F)
4002/1024 200L
JCB Hydraulic Fluid HP46-10°C
(14°F) to 30°C (86°F)
4002/0803 200L
Hydraulic System 430L
JCB Hydraulic Fluid HP680°C (32°F)
to 40°C (104°F)
4002/0701 200L
Slew Ring Bearings JCB Special HP Grease 4003/2017 0.4kg
10. Technical Data
Fluids, Lubricants and Capacities
342 9821/9700-1 342
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
Slew Ring Gear
Teeth
JCB Special HP Grease 4003/2017 0.4kg
All Other Grease As required JCB Special HP Grease 4003/2006 12.5kg
(1) For information about the different container sizes that are available (and their part numbers), contact your
local JCB dealer.
(2) Do not use ordinary engine oil.
(3) Failure to use oil of the correct specification will decrease the life of the engine and the diesel particulate filter.
(For: JS200, JS210, JS220, JS235)
JCB recommend that you use the JCB lubricants shown as they have been verified by JCB for use on JCB
machines. However, you could use other lubricants that are equivalent to the JCB standards and quality or
offer the same machine component protection.
Table 4. Fluids, Lubricants and Capacities
Item Capacity Fluid/Lubricant JCB Part
Number
Container
Size
(1)
Fuel Tank 343L Diesel - -
-10°C (14°F) to 50°C (121.9°F) JCB
Engine Oil EP 15W/40
4001/1805 20LEngine (Oil)
(2)
17.5L
-20°C (-4°F) to 50°C (122°F): JCB
Cold Climate Engine Oil EP 5W40
4001/2705 20L
Cooling System 28L JCB Antifreeze HP/Coolant 4006/1120 20L
Track Gearbox
(each)
4.7L JCB HD90 Gear Oil 4001/0301 5L
Slew Gearbox 5L JCB HD90 Gear Oil 4000/0305 20L
Track Rollers and
Idler Wheels
JCB HD90 Gear Oil 4000/0305 20L
Recoil Spring Cylin-
der
JCB Special HP Grease 4003/2017 0.4kg
JCB Hydraulic Fluid HP32-20°C
(-4°F) to 15°C (59°F)
4002/1024 200L
JCB Hydraulic Fluid HP46-10°C
(14°F) to 30°C (86°F)
4002/0803 200L
Hydraulic System 200L
JCB Hydraulic Fluid HP680°C (32°F)
to 40°C (104°F)
4002/0701 200L
Slew Ring Bearings 0.1kg JCB Special HP Grease 4003/2017 0.4kg
Slew Ring Gear
Teeth
17kg JCB Special HP Grease 4003/2006 12.5kg
All Other Grease As required JCB Special HP Grease 4003/2006 12.5kg
(1) For information about the different container sizes that are available (and their part numbers), contact your
local JCB dealer.
(2) Do not use ordinary engine oil.
11. Technical Data
Fluids, Lubricants and Capacities
343 9821/9700-1 343
Fuel
For: JS115, JS130, JS145, JS160, JS180, JS190, JS200, JS210, JS220, JS235, ................ Page 343
For: JS330, JS360 ................................................................................................................. Page 346
(For: JS115, JS130, JS145, JS160, JS180, JS190, JS200, JS210, JS220, JS235,)
Acceptable and Unacceptable Fuels
Notice: No warranty liability whatsoever will be accepted for failure of fuel injection equipment where the
failure is attributed to the quality and grade of the fuel used.
Warning! Do not use petrol in this machine. Do not mix petrol with the diesel fuel. In storage tanks the
petrol will rise to the top and form flammable vapours.
Fuel Groups
The major world fuels standards are divided into four categories. Those that are fully accepted as suitable fuels,
those that are acceptable from a "warranty" point of view, but may have undesirable affects on the expected
life of the engine performance changes from original specification, those that will lead to reduce the expected
life, and lastly those that are viewed as unacceptable for use (fuels shown on the same line as each other are
considered equivalents).
The lists below are not exhaustive of all diesel fuel standards encountered in the marketplace. If comment
is required on the suitability of fuel standards not on the list, requests with, if possible, specification details
showing at least the key characteristics described above should be forwarded to JCB Service for assessment
and comment.
Table 1. Group 1
Fuel Advice Service Requirements
EN590 Diesel fuel types - Auto/C0/
C1/C2/C3/C4
BS2869 Class A2
ASTM D975-076 2-D, US DF1, US
DF2, US DFA
JIS K2204 Grades 1, 2, 3 and Spe-
cial Grade 3
Preferred and may be used with no
restrictions or conditions.
For fuel with unspecified parame-
ters, EN590 values apply. Fuel
grades within each standard must
be appropriate to the ambient tem-
perature. The appropriate level of
fuel cleanliness at the FIE inlet af-
ter filtration has to be ensured by
the customer.
(1) See your JCB dealer for advice on service requirements.
Table 2. Group 2
Fuel Advice Service Requirements
Group1 fuels with HFFR WSD in
the range 460 to 520
ASTM D975-91 Class 1-1DA
B20 Biodiesels can cause serious
problems for engines. JCB Eco-
max Stage 3b / Tier 4i engines
have been developed to run with
biodiesels up to 20 mix (B20), but
NOT with higher biodiesel propor-
tion. The biodiesel content of this
mix must be to ASTM D6751, DIN
51606, or ISO 14214 standards.
Using a B20 blend of biodiesel re-
quires caution and additional ser-
vicing of the engine is required.
(1)
Not preferred and may be used but
may lead to reduced FIE life and /
or loss of performance.
The Ecomax dealer, or JCB Pow-
er Systems Applications depart-
ment, should be consulted for fur-
ther guidance. Biodiesel is very
problematic to store; fuel in storage
has to be very carefully managed
to ensure that it does not deterio-
rate during this period. No warranty
liability will be accepted for failure
of fuel injection equipment where
the failure is attributed to the quali-
ty and grade of the fuel used.
(1) See your JCB dealer for advice on service requirements.
12. Technical Data
Fluids, Lubricants and Capacities
344 9821/9700-1 344
Table 3. Group 3
Fuel Advice
AVTUR FS11 (NATO F34, JP8, MIL T83133, DEF
STAN 91-87, DERD 2463)
AVCAT FS11 (NATO F44, JP5, MIL T5624, DERD
2452, AVTOR))
JET A1 (NATO F35, DEF STAN 91-91, DERD 2494)
AVCAT (NATO F43, JP5 without additives)
JET A (ASTM D1655)
ASTM D3699 Kerosene
JP7 (MIL T38219 XF63)
NATO F63
Not preferred and may be used only with appropri-
ate additives and will lead to reduced FIE life and / or
loss of performance.
(1) See your JCB dealer for advice on service requirements.
Table 4. Group 4
Fuel Advice
Unmodified Vegetable Oils and Biodiesels over
20concentration
Unacceptable
(1) See your JCB dealer for advice on service requirements.
Additives
The additives listed below are advertised as being suitable for bringing the lubricity levels of kerosene/low
sulphur fuels up to those of diesel fuels.
These products are given as examples only. The information is derived from the manufacturers data. The
products are not recommended or endorsed by JCB. Contact your JCB dealer for further advice.
• Elf 2S 1750. Dosage 1000-1500 ppm (0.1% to 0.15%), specifically for Indian Superior Kerosene (SKO)
but may be applicable to other fuels.
• Lubrizol 539N. Dosage (on Swedish low sulphur fuel) 250 ppm.
• Paradyne 7505 (from Infineum). Dosage 500 ppm (0.05%).
These products are given as examples only. The information is derived from the manufacturers data. The
products are not recommended or endorsed by JCB.
Service Requirements for use of B20 Biodiesel
• The engine oil must be a grade CH4 as minimum specification.
• Do not leave unused B20 biodiesel in the fuel tank for extended periods (top up each day).
• Make sure that 1 in 5 fuel tank fills use standard diesel to EN590 specification, this will help to prevent
'gumming'.
• Make sure regular oil sampling is completed (look for excessive unburnt fuel content, water or wear
particles.
• Change the engine oil and filter more frequently (as a minimum half the recommended intervals), or as
indicated by oil sampling.
• Change the fuel filters more frequently (as a minimum half the recommended intervals), or if there are
engine performance related issues..
• Make sure the fuel is stored correctly, care must be taken to make sure no water enters the machine fuel
tank (or the storage tank). Water will encourage micobacterial growth.
• Make sure that the fuel pre-filter is drained daily (not every week as currently advised).
• Use heater kits in low ambient temperature territories.
• The biodiesel must meet the following standards: ASTM D6751, DIN 51606, ISO 14214.
If necessary use a test kit to confirm the fuel specification. Testing kits are available (not from JCB currently),
use the internet as a source for the kits.
13. Technical Data
Fluids, Lubricants and Capacities
345 9821/9700-1 345
If performance related issues are to be reported to JCB Service, and the engine has been run on biodiesel, then
the fuel system must be filled with standard diesel (at least 2 x tank fills) to EN590 specification and relevant
stall speeds recorded prior to making the report.
Warranty
JCB have shown a commitment to support the environment by approving the use of biodiesel blended fuels.
Using a B5 blend of biodiesel requires caution and additional servicing of the engine is required.
Failure to follow the additional recommended service requirements may lead to a warranty claim being declined.
Failures resulting by the incorrect use of biodiesels or other fuel additives are not defects of the engine
workmanship and therefore will not be supported by JCB Warranty.
Usage and Effects of Fuels
The information that follows does not indicate types of fuel that are acceptable or unacceptable.
Acceptable Fuels
Ultra Low Sulphur Diesel (EN590)
Available throughout the UK, Europe and North America since March 1999. This fuel has a maximum sulphur
content of 0.001% (0.0015% in North America) by weight and a further reduction in the natural lubricity and
aromatic content than experienced with low sulphur diesel. Major oil producers will add lubrication improvers
and also maintain the total aromatic content to an acceptable level.
B20 Biodiesel
Biodiesel refers to pure fuel before it is blended with diesel fuel. When biodiesel is blended with diesel fuel it
is referred to as B5, B20 etc., where the number indicates the percentage of biodiesel in the fuel, for example
B5 contains 5% biodiesel.
Biodiesel has different characteristics than mineral based fuels, this could lead to seals swelling, fuel system
corrosion and seal damage.
Biodiesels will 'cloud' at higher temperatures than mineral based fuels. To explain Cloud Point - the lowest
temperature at which fluid can flow and performs its functions is referred to as Pour Point. Just prior to reaching
its Pour Point the diesel fluid becomes 'cloudy' due to crystallization of waxy constituents - this is know as Cloud
Point. Using diesel at temperature below its cloud point can result in filter clogging. To prevent this happening
preheating will be required.
Using B20 biodiesel can result in unburnt fuels accumulating in the engine oil, ultimately this can affect the
engine oil efficiency and lead to engine damage (with standard diesel any unburnt fuel evaporates off the
lubricating oil).
The natural properties of biodiesel make it a good medium for micro bacterial growth, these microbes can
cause fuel system corrosion and early fuel filter blocking. Biodiesels must be stored to exclude water absorption
and oxidation. It will be necessary to consult and seek advice from your fuel supplier, the effectiveness of
conventional antibacterial additives when used in biodiesel is still being investigated in the fuel industry. A high
percentage biodiesel mixture (>205%) can lead to fuel gelling and filter blocking in low temperature operation,
it may also effect the power and performance of the engine.
To minimise the risk of engine damage when using a B20 mix, there are additional service requirements.
If the recommended actions are not taken there may be the following consequences:- low temperature filter
clogging- injectors lacquering / sticking deterioration of seals and rubber hoses- corrosion of metal parts in the
fuel system- engine performance problems. These risks will be increased if the fuel has been poorly stored,
that is deteriorated through oxidation and / or water absorption.
14. Technical Data
Fluids, Lubricants and Capacities
346 9821/9700-1 346
Unacceptable Fuels
B100 - Chemically Modified Vegetable Oils (FAME/ VOME)
These fuels have been derived from a wide range of vegetable oils and animal fats, resulting in better stability,
viscosity and cetane number than those produced from unmodified vegetable oils, but it is recognised that
there are potential problems associated with the finished fuel characteristics. These oils are less stable than
mineral oil derived fuels when stored and they will readily degrade producing fatty acids, methanol and water,
none of which are desirable in the FIE. These effects are known to be accelerated when the fuel is stored in
the presence of air and water together.
An extract 'common statement' from the FIE manufactures specifies that "The fuel injection equipment
manufacturers can accept no liability whatsoever for failure attributable to operating their products with fuels
for which the products were not designed, and no warranties or representations are made as to the possible
effects of running these products with such fuels".
Unmodified Vegetable Oils
Burned in diesel engines neat or used as an extender to mineral derived fuel. When these are subjected to
heat in the fuel injection system they form sticky deposits that can be found inside the fuel pump and a hard
lacquer in the injectors where exposure to even higher temperatures takes place.
Sulphur Content
Caution! A combination of water and sulphur will have a corrosive chemical effect on fuel injection
equipment. It is essential that water is eradicated from the fuel system when high sulphur fuels are used.
Effects of Fuel Contaminates
The effect of dirt, water and other contaminants in diesel can be disastrous for injection equipment:
Dirt
A severely damaging contaminant. Finely machined and mated surfaces such as delivery valves and distributor
rotors are susceptible to the abrasive nature of dirt particles - increased wear will almost inevitably lead to
greater leakage, uneven running and poor fuel delivery.
Water
Water can enter fuel through poor storage or careless handling, and will almost inevitably condense in fuel
tanks. The smallest amounts of water can result in effects that are just as disastrous to the fuel injection pump
as dirt, causing rapid wear, corrosion and in severe cases, even seizure. It is vitally important that water is
prevented from reaching the fuel injection equipment. The filter/water trap must be drained regularly.
Wax
Wax is precipitated from diesel when the ambient temperature falls below that of the fuel's cloud point, causing
a restriction in fuel flow resulting in rough engine running. Special winter fuels may be available for engine
operation at temperatures below 0°C (32.0°F). These fuels have a lower viscosity and limit wax formation.
Chemical Contamination
It should be noted that exposure of fuel to surfaces containing Copper (Cu), Zinc (Zn) or Lead (Pb) can adversely
affect fuel quality and should be minimised.
(For: JS330, JS360)
Types of Fuel
Use good quality diesel fuel to get the correct power and performance from your engine.
15. Technical Data
Fluids, Lubricants and Capacities
347 9821/9700-1 347
Recommended Fuel Specification
• EN590 Diesel Fuel Types - Auto/Co/C1/C2/C3/C4.
• BS2869 Class A2.
• ASTM D975-91 Class 2-2DA, US DF1, US DF2, US DFA.
• JIS K2204 (1992) Grades 1, 2, 3 and Special Grade 3.
Additives
Where low sulfur/low aromatic fuels are used it is important that lubricity additives are used. The additives listed
below are advertised as being suitable for bringing the lubricity levels of kerosene/low sulfur fuels up to those
of diesel fuels. They have not been tested or approved by the engine manufacturer. They should be added by
your fuel supplier who should understand the concentration level necessary.
These products are given as examples only. The information is derived from the manufacturers data. The
products are not recommended or endorsed by JCB. Contact your JCB dealer for further advice.
• Elf 2S 1750. Dosage 1000-1500 ppm (0.1 - 0.15%), specifically for Indian Superior Kerosene (SKO) but
may be applicable to other fuels.
• Lubrizol 539N. Dosage (on Swedish low sulphur fuel) 250 ppm.
• Paradyne 7505 (from Infineum). Dosage 500 ppm (0.05%).
Acceptable Fuel Specification
The fuel specification below is acceptable, however this fuel may reduce the life of the fuel injection equipment.
The use of this fuel may also affect the engine performance.
• ASTM D975-91 Class 1-1DA.
• JP7, MIL T38219 XF63.
• NATO F63.
Sulphur Content
Caution! A combination of water and sulphur will have a corrosive chemical effect on fuel injection
equipment. It is essential that water is eradicated from the fuel system when high sulphur fuels are used.
High sulfur content can cause engine wear. (High sulfur fuel is not normally found in North America, Europe or
Australia.) If you have to use high sulfur fuel you must change the engine oil more frequently.
Table 5.
Percentage of sulfur in the fuel (%) Oil change interval
Less than 0.5 Normal
0.5 to 1.0 0.75 of normal
More than 1.0 0.50 of normal
Aviation Kerosene Fuels
Aviation kerosene fuels are not approved and their use may cause damage to components. Warranty will not
be allowed on any component where damage is found to have been caused by the use of aviation kerosene.
Low Temperature Fuels
Special winter fuels may be available for engine operation at temperatures below 0°C (32.0°F). These fuels
have a lower viscosity. They also limit wax formation in the fuel at low temperatures (Wax forming in the fuel
can stop the fuel flowing through the filter).
Fatty Acid Methyl Ester Fuels as a Replacement for diesel Fuels
Fuel resources such as Rape Methyl Ester and Soybean Methyl ester, collectively known as Fatty Acid Methyl.
16. Technical Data
Fluids, Lubricants and Capacities
348 9821/9700-1 348
Coolant
Caution! Antifreeze can be harmful. Obey the manufacturer's instructions when handling full strength or
diluted antifreeze.
Check the strength of the coolant mixture at least once a year, preferably at the start of the cold period.
Replace the coolant mixture according to the intervals shown in the machine's Service Schedule.
You must dilute full strength antifreeze with clean water before use. Use clean water of no more than a moderate
hardness (pH value 8.5). If this cannot be obtained, use de-ionized water. For further information advice on
water hardness, contact your local water authority.
The correct concentration of antifreeze protects the engine against frost damage in winter and provides year
round protection against corrosion.
The protection provided by JCB High Performance Antifreeze and Inhibitor is shown below.
Table 1.
Concentration Level of protection
50% (Standard) Protects against damage down to -40°C (-40°F)
60% (Extreme Conditions Only) Protects against damage down to -56°C (-69°F)
Do not exceed a 60% concentration, as the freezing protection provided reduces beyond this point.
If you use any other brand of antifreeze:
• Make sure that the antifreeze complies with International Specification ASTM D6210
• Always read and understand the manufacturer's instructions
• Make sure that a corrosion inhibitor is included. Serious damage to the cooling system can occur if
corrosion inhibitors are not used
• Make sure that the antifreeze is ethylene glycol based and does not use Organic Acid Technology (OAT).
17. Technical Data
Torque Values
349 9821/9700-1 349
Torque Values
General
For: JS115 .............................................................................................................................. Page 349
For: JS130, ............................................................................................................................. Page 352
For: JS145 .............................................................................................................................. Page 354
For: JS160 .............................................................................................................................. Page 356
For: JS180 .............................................................................................................................. Page 358
For: JS190 .............................................................................................................................. Page 360
For: JS330 .............................................................................................................................. Page 362
For: JS360 .............................................................................................................................. Page 364
For: JS200 .............................................................................................................................. Page 366
For: JS220, JS235 ................................................................................................................. Page 368
For: JS210 .............................................................................................................................. Page 370
(For: JS115)
JS115 and Variants
Before and after daily work, check for loose or missing nuts and bolts. Tighten if loose and replace if missing.
Tighten the nuts and bolts after the first 50h of the running-in stage and then every 250h.
Tighten the nuts and bolts, Refer to Table 1.
For the tightening torques of the bolts and nuts not listed, Refer to Table 2.
Table 1.
Tightening Point Bolt Diameter Wrench (mm) Tightening
Torque (N.m)
Checking
Torque (N.m)
1
(1)
Travel motor M16 24 290 265
2
(1)
Drive sprocket M16 24 290 265
3
(1)
Idler wheel M16 24 290 265
4
(1)
Upper (carrier) roller M16/M20 24/30 290/550 265/515
5
(1)
Lower (track) roller M16 24 290 265
6
(1)
Track guard M16 24 290 265
7 Shoe bolt M16 24 382-440 344-396
8 Counterweight M27 41 925 840
9
(1)
Turntable bearing (under-
carriage)
M16/M20 24/30 296/525 275/470
10
(1)
Turntable bearing (slew
frame)
M16/M20 24/30 296/525 275/470
11
(1)
Slew equipment M16/M20 24/30 290/550 265/515
12
(1)
Engine (engine mount) M16 24 290 265
13
(1)
Engine bracket M10/M12 17/19 68/118 62/107
14 Radiator M12 19 104 94
15
(1)
Hydraulic pump M10 17 60 54
16
(1)
Hydraulic oil tank M16 24 250 225
17
(1)
Fuel tank M16 24 250 225
18
(1)
Control valve M16 24 290 265
19 Battery M6 10 7 6
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Technical Data
Torque Values
352 9821/9700-1 352
(For: JS130,)
JS130 and Variants
Before and after daily work, check for loose or missing nuts and bolts. Tighten if loose and replace if missing.
Tighten the nuts and bolts after the first 50h of the running-in stage and then every 250h.
Tighten the nuts and bolts, Refer to Table 3.
For the tightening torques of the nuts and bolts not listed, Refer to Table 4.
Table 3.
Tightening Point Bolt Diameter Wrench (mm) Tightening
Torque (N.m)
Checking
Torque (N.m)
1
(1)
Travel motor M16 24 290 265
2
(1)
Drive sprocket M16 24 290 265
3
(1)
Idler wheel M16 24 290 265
4
(1)
Upper (carrier) roller M16/M20 24/30 290/550 265/515
5
(1)
Lower (track) roller M16 24 290 265
6
(1)
Track guard M16 24 290 265
7 Shoe bolt M16 24 382-440 344-396
8 Counterweight M27 41 925 840
9
(1)
Turntable bearing (under-
carriage)
M16/M20 24/30 296/525 275/470
10
(1)
Turntable bearing (slew
frame)
M16/M20 24/30 296/525 275/470
11
(1)
Slew equipment M16/M20 24/30 290/550 265/515
12
(1)
Engine (engine mount) M16 24 290 265
13
(1)
Engine bracket M10/M12 17/19 68/118 62/107
14 Radiator M12 19 104 94
15
(1)
Hydraulic pump M10 17 60 54
16
(1)
Hydraulic oil tank M16 24 250 225
17
(1)
Fuel tank M16 24 250 225
18
(1)
Control valve M16 24 290 265
19 Battery M6 10 7 6
20
(1)
Rotary coupling M12 19 116 105
21 Cab M16 24 132 125
(1) Use JCB Threadlocker and sealer (High Strength) and tighten to the torque listed.
Table 4.
Bolt Diameter (size) M6 M8 M10 M12 M14 M16 M18 M20
Wrench (mm) 10 13 17 19 22 24 27 30Hex. bolt
Tightening
torque
(N.m) 12.5 30 60 104 167 259 506 874
Wrench (mm) 5 6 8 10 12 14 16 17Hex. socket
head bolt Tightening
torque
(N.m) 15 36 72 125 200 311 - 607