This document is a service manual for several combine models and their engines. It contains an introduction section listing the machine models covered and their engine types. The bulk of the document is a detailed table of contents that lists over 150 individual sections providing service information on the combines' systems and components, including the engine, transmission, hydraulics, steering, climate control, electrical systems, attachments, feeding, and threshing systems.
New holland w80 c tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w80 c tier 4 compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides maintenance and repair instructions for these components.
New holland w70 c stage iiib compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland w70 wheel loader service repair manualfujsjefskekmm
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
New holland tc5080 combine harvesters service repair manualfujsjefskekmm
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance should only be performed by trained technicians using the proper tools and procedures outlined in the manual. Unauthorized repairs may void warranties.
New holland tc5.90 hillside fpt nef 6 stage iv combine harvester service repa...fujsjefskekmm
This document is a service manual for various combine harvester models. It provides maintenance and repair instructions for the engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and other components. The manual includes an introduction with safety guidelines and a table of contents listing the major vehicle systems and associated part numbers covered.
New holland tc5.90 fpt nef tier 3 combine harvester service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, diagrams and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. Each section number links to detailed information on components and subsystems such as the engine, transmission, hydrostatic drive, steering, cab climate control, threshing drum, cleaning systems, and unloading systems.
New holland mc35 commercial mower service repair manualfujsjefskekmm
The document is a service manual for New Holland commercial mowers models MC22, MC28, and MC35. It contains sections covering general information, safety, specifications, maintenance and repair of engine, drivetrain, hydraulic and electrical systems. The manual provides technical details and instructions to properly service the mowers.
New holland w80 c tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w80 c tier 4 compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides maintenance and repair instructions for these components.
New holland w70 c stage iiib compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland w70 wheel loader service repair manualfujsjefskekmm
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
New holland tc5080 combine harvesters service repair manualfujsjefskekmm
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance should only be performed by trained technicians using the proper tools and procedures outlined in the manual. Unauthorized repairs may void warranties.
New holland tc5.90 hillside fpt nef 6 stage iv combine harvester service repa...fujsjefskekmm
This document is a service manual for various combine harvester models. It provides maintenance and repair instructions for the engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and other components. The manual includes an introduction with safety guidelines and a table of contents listing the major vehicle systems and associated part numbers covered.
New holland tc5.90 fpt nef tier 3 combine harvester service repair manualfujsjefskekmm
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, diagrams and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. Each section number links to detailed information on components and subsystems such as the engine, transmission, hydrostatic drive, steering, cab climate control, threshing drum, cleaning systems, and unloading systems.
New holland mc35 commercial mower service repair manualfujsjefskekmm
The document is a service manual for New Holland commercial mowers models MC22, MC28, and MC35. It contains sections covering general information, safety, specifications, maintenance and repair of engine, drivetrain, hydraulic and electrical systems. The manual provides technical details and instructions to properly service the mowers.
New holland l234 tier 4 b (final) skid steer loader service repair manual [nh...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
New holland d180 c stage iiib crawler dozer service repair manual (pin nedc18...fujsjefskekmm
This service manual section provides information for removing and installing the engine and crankcase assembly on a D180C crawler dozer. The 6-step removal process involves using lifting equipment to detach the engine from the frame mounts at the front and sides. Proper lifting points and balance of the 631 kg engine are emphasized for safety.
New holland d150 c stage iiib crawler dozer service repair manual (pin nedc15...fujsjefskekmm
This service manual provides information for servicing the following components of a D150C crawler dozer:
- Engine and related systems such as air cleaners, fuel filters, cooling and emissions systems
- Hydrostatic drive system
- Brakes and controls
- Hydraulic systems including cylinders, pumps and valves
- Tracks and track suspension
- Cab climate control and electrical systems
- Dozer blade and tools
- Cab, bodywork and decals
It provides removal and installation instructions as well as specifications for maintenance and repair of these components.
New holland cr940 combine harvesters service repair manualfujsjefskekmm
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electrics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
New holland c238 tier 4 b (final) compact track loader service repair manual ...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
Case 621 f tier 4 wheel loader service repair manualfujsjefskekmm
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connecting parts. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland br6090 combi service repair manualfujsjefskekmm
This document provides a service manual for a BR6090 COMBI machine. It includes sections on hydraulic, pneumatic, electrical, electronic and other systems. It details components like the secondary hydraulic power system, electrical power system, lighting system, electronic system, lubrication system and more. It also covers the engine and PTO, transmission, process drive, axles, brakes, steering, wheels, frame, and crop processing functions. Torque specifications are provided for hardware.
New holland b100 btc backhoe loader service repair manualfujsjefskekmm
This document contains service manual sections for various backhoe loader models. It includes information on safety rules, maintenance, technical specifications, transmission systems, front axles, and other components. Technical specifications include details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets, tires, and machine dimensions and performance specs. The transmission and front axle sections provide specifications, lubrication instructions, removal/installation procedures, and troubleshooting guides.
New holland b100 blr backhoe loader service repair manualfujsjefskekmm
This document contains service manuals for various backhoe loader models including the B90B, B100B, B110B, and B115B. It includes sections on safety, maintenance, technical specifications, troubleshooting, and repair procedures for components like the transmission, axles, brakes, hydraulics, electrical systems, and attachments. The manuals provide information on lubrication, removal and installation of parts, disassembly and assembly of systems, and repair times for maintenance and repairs.
New holland b95 lr backhoe loader service repair manualfujsjefskekmm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b95 ctc tier 4b (final) tractor loader backhoe service repair manualfujsjefskekmm
This document is a service manual for New Holland tractor loader backhoes that covers specifications, maintenance, and repair procedures. It includes sections on the engine and fuel systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, climate control, electrical systems, front loader/bucket, booms/dippers/buckets, and cab/bodywork. Safety precautions are provided to ensure safe operation and service of the equipment.
Case 121 f xt tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
- The document is a service manual that provides instructions for removing the engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, removing protective covers and grids, and using lifting equipment to extract the engine from the rear of the vehicle. The process involves multiple steps to properly prepare the machine before removing and lowering the engine.
Case 121 f xt tier 4a (interim) compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for Case compact wheel loaders models 121F XT, 121F ZB, 21F XT, 21F ZB, 221F HS, 221F STD, 321F HS, and 321F STD. It provides maintenance instructions and repair procedures for components of the wheel loaders including the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln 322cln excavator (prefix bfk) service repair manual ...fujsjefskekmm
This document provides disassembly instructions for a final drive on a 322C excavator. It outlines 32 steps to fully disassemble the final drive. The steps include removing housing components, gears, carriers, seals, and other parts. Special tools are listed that are required for removal of components. Cleanliness is emphasized during disassembly to prevent dirt entry. Weights of removed parts are provided.
Caterpillar cat 322 c l 322cl excavator (prefix blp) service repair manual (b...fujsjefskekmm
This document provides step-by-step instructions for disassembling various components of a 322C excavator's auxiliary control valve, including the solenoid valve and housing, spool and plug, line relief valve, and load hold check valve. It details removing o-rings, fittings, valves, spools, and other parts. Cleanliness is emphasized to prevent contamination of the hydraulic system during disassembly and reassembly.
Caterpillar cat 322 c l 322cl excavator (prefix bkj) service repair manual (b...fujsjefskekmm
The document provides instructions for installing a cylinder head on a 3126 engine. It describes:
1) Cleaning the cylinder head and cylinder block mating surfaces and installing a new cylinder head gasket.
2) Positioning the cylinder head on the dowels and lowering it onto the cylinder block.
3) Tightening the cylinder head bolts in a specific sequence and torque pattern.
Caterpillar cat 322 c excavator (prefix bfk) service repair manual (bfk00001 ...fujsjefskekmm
This document provides instructions to disassemble the final drive of a 322C excavator. It outlines 32 steps to remove components like gears, carriers, seals, and housings. Required tools include a transmission repair stand, link brackets, retaining ring pliers, and a spanner socket. Cleanliness is important to prevent dirt from entering during reassembly. Alignment marks should be made and parts reinstalled in their original locations.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsjefskekmm
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and properly cap openings to prevent contamination. Safety notices are also included to keep parts clean and contain fluids.
New holland l234 tier 4 b (final) skid steer loader service repair manual [nh...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
New holland d180 c stage iiib crawler dozer service repair manual (pin nedc18...fujsjefskekmm
This service manual section provides information for removing and installing the engine and crankcase assembly on a D180C crawler dozer. The 6-step removal process involves using lifting equipment to detach the engine from the frame mounts at the front and sides. Proper lifting points and balance of the 631 kg engine are emphasized for safety.
New holland d150 c stage iiib crawler dozer service repair manual (pin nedc15...fujsjefskekmm
This service manual provides information for servicing the following components of a D150C crawler dozer:
- Engine and related systems such as air cleaners, fuel filters, cooling and emissions systems
- Hydrostatic drive system
- Brakes and controls
- Hydraulic systems including cylinders, pumps and valves
- Tracks and track suspension
- Cab climate control and electrical systems
- Dozer blade and tools
- Cab, bodywork and decals
It provides removal and installation instructions as well as specifications for maintenance and repair of these components.
New holland cr940 combine harvesters service repair manualfujsjefskekmm
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electrics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
New holland c238 tier 4 b (final) compact track loader service repair manual ...fujsjefskekmm
This document provides service information for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B diesel engines. It contains introduction information and sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, front loader and bucket, cab, frames and ballasting, wheels, tracks and suspension, cab climate control, electrical systems, and fault codes. The document provides detailed procedures, part numbers, and diagrams for servicing and repairing components of these machines.
Case 621 f tier 4 wheel loader service repair manualfujsjefskekmm
The document provides instructions for removing the engine from a 621F wheel loader. Key steps include draining fluids, disconnecting batteries, removing the radiator cap and draining coolant, tagging wiring harnesses, removing hood mounting bolts, and lifting the engine out after disconnecting all connecting parts. Safety precautions are described such as releasing hydraulic pressure before removal.
New holland br6090 combi service repair manualfujsjefskekmm
This document provides a service manual for a BR6090 COMBI machine. It includes sections on hydraulic, pneumatic, electrical, electronic and other systems. It details components like the secondary hydraulic power system, electrical power system, lighting system, electronic system, lubrication system and more. It also covers the engine and PTO, transmission, process drive, axles, brakes, steering, wheels, frame, and crop processing functions. Torque specifications are provided for hardware.
New holland b100 btc backhoe loader service repair manualfujsjefskekmm
This document contains service manual sections for various backhoe loader models. It includes information on safety rules, maintenance, technical specifications, transmission systems, front axles, and other components. Technical specifications include details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets, tires, and machine dimensions and performance specs. The transmission and front axle sections provide specifications, lubrication instructions, removal/installation procedures, and troubleshooting guides.
New holland b100 blr backhoe loader service repair manualfujsjefskekmm
This document contains service manuals for various backhoe loader models including the B90B, B100B, B110B, and B115B. It includes sections on safety, maintenance, technical specifications, troubleshooting, and repair procedures for components like the transmission, axles, brakes, hydraulics, electrical systems, and attachments. The manuals provide information on lubrication, removal and installation of parts, disassembly and assembly of systems, and repair times for maintenance and repairs.
New holland b95 lr backhoe loader service repair manualfujsjefskekmm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b95 ctc tier 4b (final) tractor loader backhoe service repair manualfujsjefskekmm
This document is a service manual for New Holland tractor loader backhoes that covers specifications, maintenance, and repair procedures. It includes sections on the engine and fuel systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, climate control, electrical systems, front loader/bucket, booms/dippers/buckets, and cab/bodywork. Safety precautions are provided to ensure safe operation and service of the equipment.
Case 121 f xt tier 4b (final) compact wheel loader service repair manualfujsjefskekmm
- The document is a service manual that provides instructions for removing the engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, removing protective covers and grids, and using lifting equipment to extract the engine from the rear of the vehicle. The process involves multiple steps to properly prepare the machine before removing and lowering the engine.
Case 121 f xt tier 4a (interim) compact wheel loader service repair manualfujsjefskekmm
This document is a service manual for Case compact wheel loaders models 121F XT, 121F ZB, 21F XT, 21F ZB, 221F HS, 221F STD, 321F HS, and 321F STD. It provides maintenance instructions and repair procedures for components of the wheel loaders including the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln 322cln excavator (prefix bfk) service repair manual ...fujsjefskekmm
This document provides disassembly instructions for a final drive on a 322C excavator. It outlines 32 steps to fully disassemble the final drive. The steps include removing housing components, gears, carriers, seals, and other parts. Special tools are listed that are required for removal of components. Cleanliness is emphasized during disassembly to prevent dirt entry. Weights of removed parts are provided.
Caterpillar cat 322 c l 322cl excavator (prefix blp) service repair manual (b...fujsjefskekmm
This document provides step-by-step instructions for disassembling various components of a 322C excavator's auxiliary control valve, including the solenoid valve and housing, spool and plug, line relief valve, and load hold check valve. It details removing o-rings, fittings, valves, spools, and other parts. Cleanliness is emphasized to prevent contamination of the hydraulic system during disassembly and reassembly.
Caterpillar cat 322 c l 322cl excavator (prefix bkj) service repair manual (b...fujsjefskekmm
The document provides instructions for installing a cylinder head on a 3126 engine. It describes:
1) Cleaning the cylinder head and cylinder block mating surfaces and installing a new cylinder head gasket.
2) Positioning the cylinder head on the dowels and lowering it onto the cylinder block.
3) Tightening the cylinder head bolts in a specific sequence and torque pattern.
Caterpillar cat 322 c excavator (prefix bfk) service repair manual (bfk00001 ...fujsjefskekmm
This document provides instructions to disassemble the final drive of a 322C excavator. It outlines 32 steps to remove components like gears, carriers, seals, and housings. Required tools include a transmission repair stand, link brackets, retaining ring pliers, and a spanner socket. Cleanliness is important to prevent dirt from entering during reassembly. Alignment marks should be made and parts reinstalled in their original locations.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsjefskekmm
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and properly cap openings to prevent contamination. Safety notices are also included to keep parts clean and contain fluids.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
10. INTRODUCTION
Basic instructions - How to use and navigate through this Manual
Technical information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery (eTim), DVD and in paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
51431545 08/02/2018
3
11. INTRODUCTION
How to use this manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number 00, 35, 55, etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
PRODUCT
Tractors
Vehicles with working arms: backhoes,
excavators, skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance
05 - Machine completion and equipment
10 - Engine
14 - Main gearbox and drive
18 - Clutch
21 - Transmission
23 - Four wheel drive system
25 - Front axle system
27 - Rear axle system
29 - Hydrostatic drive
31 - Implement power take-off
33 - Brakes and controls
35 - Hydraulic systems
36 - Pneumatic system
37 - Hitches, drawbars and implement couplings
39 - Frames and ballasting
41 - Steering
44 - Wheels
46 - Steering clutches
48 - Tracks and track suspension
50 - Cab climate control
55 - Electrical systems
56 - Grape harvester shaking
58 - Attachments/headers
60 - Product feeding
61 - Metering system
62 - Pressing - Bale formation
51431545 08/02/2018
4
12. INTRODUCTION
63 - Chemical applicators
64 - Chopping
66 - Threshing
68 - Tying/Wrapping/Twisting
69 - Bale wagons
70 - Ejection
71 - Lubrication system
72 - Separation
73 - Residue handling
74 - Cleaning
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding
78 - Spraying
79 - Planting
80 - Crop storage / Unloading
82 - Front loader and bucket
83 - Telescopic single arm
84 - Booms, dippers and buckets
86 - Dozer blade and arm
88 - Accessories
89 - Tools
90 - Platform, cab, bodywork and decals
51431545 08/02/2018
5
13. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51431545 08/02/2018
12
14. SERVICE MANUAL
Engine
CX5.80 FPT NEF 6 STAGE IV, CX5.90 FPT NEF 6 STAGE IV, CX5.90 FPT NEF
6 TIER 3, CX5.90 Hillside FPT NEF 6 STAGE IV, CX5.90 Laterale FPT NEF 6
TIER 4B (FINAL) AND STAGE IV, CX6.80 FPT NEF 6 STAGE IV, CX6.80 FPT
NEF 6 TIER 3, CX6.90 FPT CURSOR 9 STAGE IV, CX6.90 FPT CURSOR 9
TIER 3, CX6.90 FPT CURSOR 9 TIER 3, CX6.90 Laterale FPT CURSOR 9 TIER
4B (FINAL) AND STAGE IV
51431545 08/02/2018
10
15. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Remove
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.90 FPT CURSOR 9 STAGE IV
CX6.90 Laterale FPT CURSOR 9 TIER 4B (FINAL) AND STAGE IV
NOTE: It is required to remove the rear right-hand side
shield (1) to gain access to the DEF/AdBlue® tank.
The shield (1) is secured to the machine frame at four lo-
cations (A), (B), (C) and (D).
ZEIL14CXM0123AZ 1
NOTE: Access to some of the hardware is through the
straw walker inspection cover (2).
ZEIL14CXM0131AA 2
CAUTION
Heavy object!
The component is heavy. Use care not to drop
the component when installing, removing, or
handling.
Failure to comply could result in minor or mod-
erate injury.
C0095A
1. Use a suitable hoist and secure the rear right-hand side
shield (1).
ZEIL14CXM0123AA 3
51431545 08/02/2018
10.1 [10.500] / 3
16. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
2. Remove the hardware (3) and (4) from the rear right-
hand side shield at the location (A) (see figure 1).
ZEIL14CXM0124AA 4
3. Remove the hardware (5) and the cover plate (6) at the
location (B) (see figure 1).
NOTE: Get access to the hardware (5) through the cover
(2) (see figure 2).
ZEIL14CXM0125AA 5
4. Remove the hardware (7) from the rear right-hand side
shield (1) at the location (C) (see figure 1).
ZEIL14CXM0127AA 6
5. Remove the hardware (8) from the rear right-hand side
shield (1) at the location (D) (see figure 1).
6. Remove the rear right-hand side shield (1).
ZEIL14CXM0126AA 7
51431545 08/02/2018
10.1 [10.500] / 4
17. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
7. On the DEF/AdBlue® tank (9), loosen the clamp (10)
and remove the cover (11).
8. Disconnect the DEF/AdBlue® line (12).
ZEIL14CXM0128AA 8
9. Disconnect the electrical connector (13).
10. Mark and disconnect the DEF/AdBlue® lines (14) and
(15).
ZEIL14CXM0129AA 9
11. On the DEF/AdBlue® tank (9), remove the hardware
(16).
NOTE: Get access to the hardware (16) through the straw
walker inspection cover (2) (see figure 2).
ZEIL14CXM0130AA 10
CAUTION
Heavy object!
The component is heavy. Use care not to drop
the component when installing, removing, or
handling.
Failure to comply could result in minor or mod-
erate injury.
C0095A
12. Secure the DEF/AdBlue® tank (9) with a suitable fork-
lift and slings.
13. Support the DEF/AdBlue® tank (9) and remove the
hardware (17).
14. Slowly remove the DEF/AdBlue® tank (9) from the
machine frame.
ZEIL14CXM0132AA 11
51431545 08/02/2018
10.1 [10.500] / 5
18. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Install
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.90 FPT CURSOR 9 STAGE IV
CX6.90 Laterale FPT CURSOR 9 TIER 4B (FINAL) AND STAGE IV
CAUTION
Heavy object!
The component is heavy. Use care not to drop
the component when installing, removing, or
handling.
Failure to comply could result in minor or mod-
erate injury.
C0095A
1. Use a suitable forklift and install the DEF/AdBlue® tank
(1) on the machine frame.
2. Support the DEF/AdBlue® tank (1) and install the hard-
ware (2). ZEIL14CXM0132AA 1
3. Open the straw walker inspection cover (3).
ZEIL14CXM0131AA 2
4. Install the hardware (4) through the straw walker in-
spection cover (3) (see figure 2).
ZEIL14CXM0130AA 3
51431545 08/02/2018
10.1 [10.500] / 6
19. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
5. Connect the electrical connector (5).
6. Connect the DEF/AdBlue® lines (6) and (7).
NOTE: Use the marks previously applied.
ZEIL14CXM0129AA 4
7. Install the cover (8) and tighten the clamp (9).
8. Install the DEF/AdBlue® line (10).
ZEIL14CXM0128AA 5
CAUTION
Heavy object!
The component is heavy. Use care not to drop
the component when installing, removing, or
handling.
Failure to comply could result in minor or mod-
erate injury.
C0095A
9. Use a suitable hoist and align the rear right-hand side
shield (11) to the machine frame.
ZEIL14CXM0123AA 6
10. Install the upper left-hand side of the shield (11) on
the machine frame. Use the hardware (12). Do not
tighten yet.
ZEIL14CXM0126AA 7
51431545 08/02/2018
10.1 [10.500] / 7
20. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
11. Install the upper right-hand side of the shield (11) on
the machine frame. Use the cover plate (13) and the
hardware (14). Do not tighten yet.
NOTE: Get access to the hardware (14) through the straw
walker inspection cover (3) (see figure 2).
ZEIL14CXM0125AA 8
12. Install the lower right-hand side of the shield (11) on
the machine frame. Use the hardware (15) and (16).
Do not tighten yet.
ZEIL14CXM0124AA 9
13. Install the lower left-hand side of the shield (11) on the
machine frame. Use the hardware (17).
14. Tighten all the hardware.
ZEIL14CXM0127AA 10
51431545 08/02/2018
10.1 [10.500] / 8
21. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA filters - Service
instruction
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.90 FPT CURSOR 9 STAGE IV
CX6.90 Laterale FPT CURSOR 9 TIER 4B (FINAL) AND STAGE IV
Main filter
1. On the supply module (1). Remove the filter cover (2),
turn counter-clockwise.
NOTE: Required tool : 27 mm wrench.
ZEIL15TC00307AA 1
2. Remove the equalizing element (3).
ZEIL15TC00308AA 2
3. Check the color of the filter (4) inside.
ZEIL15TC00309AA 3
51431545 08/02/2018
10.1 [10.500] / 9
22. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
4. Choose the correct side of the tool (5) that comes with
the replacement filter.
• (B) side for black filter.
• (G) side for grey filter.
ZEIL15TC00310AA 4
5. Insert the correct side of the tool (5) into the filter (4)
until a click is noticed.
6. Pull out the filter (4) with the tool (5) by hand. If nec-
essary insert a screwdriver in the slot of the tool (5) to
help extract the filter (4).
ZEIL15TC00311AA 5
7. Clean functional surfaces indicated by the arrow with
clean water only.
NOTE: Protect the filter chamber from contamination and
particles.
8. Lubricate the O-rings (6) with MOBIL VELOCITE™ NO. 6
OIL and insert the new filter (4) into the supply module
(1).
ZEIL15TC00312AA 6
9. Insert the new equalizing element (3).
ZEIL15TC00308AA 7
51431545 08/02/2018
10.1 [10.500] / 10
23. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
10. On the supply module (1). Install the filter cover (2),
clockwise. Torque to 15 – 25 N·m (132.8 – 221 lb in).
ZEIL15TC00307AA 8
In-line filter
11. Remove the cover (2) from the housing (1).
NOTE: Required tools: 24 mm and 27 mm wrench.
ZEIL16TC00023AA 9
12. Remove the spacer (3) from the housing (1).
13. Remove the filter (4) from the cover (2).
ZEIL16TC00003AA 10
14. Clean the housing (1), the spacer (3) and the cover
(2) with clean water only.
15. Check the O-ring (5) and the O-ring (6) for damage,
replace if necessary.
ZEIL16TC00003AZ 11
51431545 08/02/2018
10.1 [10.500] / 11
24. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
16. Install the new filter (4) on the cover (2).
17. Install the spacer (3) inside the housing (1).
ZEIL16TC00003AA 12
18. Install the cover (2) on the housing (1). Torque to 10
– 14 N·m (7.4 – 10 lb ft).
ZEIL16TC00023AA 13
51431545 08/02/2018
10.1 [10.500] / 12
25. Engine - Engine air compressor
Air compressor - Remove
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 TIER 3
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.80 FPT NEF 6 TIER 3
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir (1).
ZEIL06CS0207A0B 1
2. Loosen the retaining strap (1) and remove the air inlet
pipe (2) from the air compressor (3).
NOTE: Protect the air inlet and outlet ports from dirt
ingress.
3. Loosen the connection (4) to remove the hose (5) from
the air compressor (3).
ZEIL06CS0082A0B 2
4. Drain sufficient coolant from the engine cooling system
to allow removal of the coolant lines.
5. Loosen the connection (6).
ZEIL06CS0083A0B 3
51431545 08/02/2018
10.3 [10.450] / 9
26. Engine - Engine air compressor
6. Loosen the connection (7).
7. Remove the four bolts (8) to remove the support (9).
ZEIL06CS0084A0B 4
8. Remove the two nuts (10) to remove the air compressor
(3) from the engine.
ZEIL06CS0085A0B 5
51431545 08/02/2018
10.3 [10.450] / 10
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Engine - Engine air compressor
Air compressor - Install
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 TIER 3
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.80 FPT NEF 6 TIER 3
1. Install the air compressor (3) on the engine and tighten
the two nuts (10).
ZEIL06CS0085A0B 1
NOTE: Make sure that the O-ring (11) is positioned well. If
necessary apply grease.
ZEIL06CS0086A0B 2
2. Install the support (9) with the four bolts (8).
3. Install the tube and tighten the connection (7).
ZEIL06CS0084A0B 3
51431545 08/02/2018
10.3 [10.450] / 11
29. Engine - Engine air compressor
4. Install the tube and tighten the connection (6).
ZEIL06CS0083A0B 4
5. Install the hose (5) on the air compressor (3) and
tighten the connection (4).
6. Install the pipe (2) on the air compressor (3) and tighten
the retaining strap (1).
ZEIL06CS0082A0B 5
7. Close the drain (2) at the bottom of the reservoir (1).
8. Add engine coolant to the cooling system, refer to the
Operator’s Manual for more details.
9. Start the engine to charge the system with air. Allow the
air system to build up pressure to the governor cutout.
Stop the engine and use a soap and water solution at
the connection points to check for air leaks. Make any
necessary repairs.
ZEIL06CS0207A0B 6
51431545 08/02/2018
10.3 [10.450] / 12
30. Engine - Engine air compressor
Air compressor - Remove
CX6.90 FPT CURSOR 9 STAGE IV
CX6.90 FPT CURSOR 9 TIER 3 ---
CX6.90 Laterale FPT CURSOR 9 TIER 4B (FINAL) AND STAGE IV
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir (1).
ZEIL06CS0207A0B 1
2. Remove the hose (3) from the fitting in the compressor.
NOTE: Protect the air inlet and outlet ports from dirt
ingress.
3. Disconnect the small tube (4) from the fitting in the com-
pressor.
4. Loosen the clamp (5) and remove the elbow (6) from
the fitting in the compressor.
ZEIL11CX0671A0B 2
5. Drain sufficient coolant from the engine cooling system
to allow removal of the coolant lines.
6. Remove the coolant lines (7) and (8).
7. Remove the air compressor pump (10) from the engine
by removing the three Allen screws (9). Make sure to
capture the seals as the pump (10) is pulled away from
the engine.
ZEIL11CX0671A0C 3
51431545 08/02/2018
10.3 [10.450] / 13
31. Engine - Engine air compressor
Air compressor - Install
CX6.90 FPT CURSOR 9 STAGE IV
CX6.90 FPT CURSOR 9 TIER 3 ---
CX6.90 Laterale FPT CURSOR 9 TIER 4B (FINAL) AND STAGE IV
1. If necessary, install the drive gear to the compressor
pump (10) and torque the nut to 135 – 145 Nm (99.6 –
106.9 lb ft).
2. Install the O–ring seals in the recess of the mounting
flange, apply some multi-purpose grease. Mount the
air compressor pump (10) on to the engine using the
three Allen screws (9). Ensure that the gears mesh
correctly, and the seals are installed.
3. Install the coolant lines (7) and (8) on the air compres-
sor pump (10).
ZEIL11CX0671A0C 1
4. Install the elbow (6) on the air compressor pump using
the collar (5).
5. Install the small tube (4) on to the fitting in the air com-
pressor pump.
6. Install the hose (3) on the fitting in the air compressor
pump.
ZEIL11CX0671A0B 2
7. Close the drain (2) at the bottom of the air reservoir (1).
8. Add engine coolant to the cooling system, refer to the
Operator’s Manual for more details.
9. Start the engine to charge the system with air. Allow the
air system to build up pressure to the governor cutout.
Stop the engine and use a soap and water solution at
the connection points to check for air leaks. Make any
necessary repairs.
ZEIL06CS0207A0B 3
51431545 08/02/2018
10.3 [10.450] / 14
32. Engine - Engine air compressor
Compressed air tank Relief valve - Remove
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 TIER 3
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.80 FPT NEF 6 TIER 3
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir (1).
ZEIL06CS0207A0B 1
2. Loosen and disconnect the air line fittings (1) from the
pressure relief valve (2).
3. Loosen the collar (5) and disconnect the tube from the
pressure relief valve (2).
4. Remove the pressure relief valve (2) by removing the
bolts (4).
ZEIL11CX0669A0B 2
51431545 08/02/2018
10.3 [10.450] / 15
33. Engine - Engine air compressor
Compressed air tank Relief valve - Install
CX5.80 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 STAGE IV
CX5.90 FPT NEF 6 TIER 3
CX5.90 Hillside FPT NEF 6 STAGE IV
CX5.90 Laterale FPT NEF 6 TIER 4B (FINAL) AND STAGE IV
CX6.80 FPT NEF 6 STAGE IV
CX6.80 FPT NEF 6 TIER 3
1. Install the pressure relief valve (2) on its support using
the bolts (4), the lock washers and the nuts.
2. Connect and tighten the air line tube fittings (1) to the
pressure relief valve (2).
3. Install the tube using the collar (5) to the pressure relief
valve (2).
ZEIL11CX0669A0B 1
4. Close the drain (2) at the bottom of the air reservoir (1).
ZEIL06CS0207A0B 2
51431545 08/02/2018
10.3 [10.450] / 16