Geoceldas Envirogrid distribuidas en Chile y Sudamérica por EMIN Sistemas Geotécnicos. Ideal para suelos, fundaciones, erosión de taludes, terraplenes y mantenimiento de caminos inestables.

1. GeoProducts, LLC
For cost-effective performance -
is the logical choice worldwide
www.geoproducts.org
Landscape Architecture
• Driveways
• Gardens - natural - rock
• Environmentally sensitive areas using native infill
• Slope erosion
• Cart Paths, Walkways
• Maintenance Roads
• Grass Parking Lots
Civil Engineering Construction • Landfill
• Structural Supports, Foundations
• Roadways, Walkways
• Retaining Walls - Composite, Gravity, Free Standing
• Pipeline & Sewer Support
• Railroad Track Support
• Water Crossings
• Boat Ramps
Erosion Control
• Re-vegetation (slopes)
• Berms
• Channel Liners
• Scour Aprons/Drop Structures
• Revetments
• Shoreline Protection
• Spillways/Chutes
Other Applications
• Replace board roads for permanent roadways to
remote locations
• Pipeline applications - support & erosion
• Structural support for camps & heavy equipment
• Levees
• Field Parking Lots
• Water Crossings
Projects completed on all continents

2. ENVIROGRID PROPERTIES
MATERIAL: The polymer used to manufacture EnviroGrid shall be virgin, non-thermally degraded high-density
polyethylene. The EnviroGrid strips shall conform to the following requirements:
MATERIAL PROPERTIES TEST METHOD UNIT TEST VALUE
Minimum Polymer Density ASTM D-1505 g/cm3
(lb/ft3
) .940 (58.7)
Environmental Stress Crack Resistance ASTM D-1693 hrs 4000
Carbon Black Content ASTM D-1603 % by weight 1.5% minimum
Nominal Sheet Thickness ASTM D-5199 mm (mils) 1.25 (50)+5%
SEAM STRENGTH:
Peel Strength – 80 lb. (357 N) per inch of cell depth per U. S. Army Corps of Engineers, Technical Report GL-86-19-A
Report, Appendix A.
Seam Hang Strength – A 102 mm (4.0 in.) weld joint supporting a load of 72.5 kg (160 lbs.) for 30 days minimum
or a 102 mm (4.2 in.) weld joint supporting a load of 72.5 kg (160 lbs.) for 7 days minimum
while undergoing temperature change from 23°C (74°F) to 54°C (130°F) on a 1 hour cycle.
ASSEMBLY: Envirogrid is manufactured in three cell sizes
EnviroGrid panels can be provided in cell heights of 2” (50 mm), 3” (75 mm), 4” (100 mm), 6” (150 mm),
8” (200 mm), 10” (250 mm) and 12” (300 mm). Standard panels are constructed of 58 strips with the
dimensions above.
Custom sizes and colors are available.
Available in solid or perforated cell wall.
259 mm
10.2 in
224 mm
8.8 in
320 mm
12.6 in
287 mm
11.3 in
508 mm
20 in
475 mm
18.7 in
EGA2O
8.4' x 21.4' (2.56m x 6.52m)
EGA3O
8.4' x 27.4' (2.56m x 8.35m)
EGA4O
8.4' x 45' (2.56m x 13.72m)
Geo Products, LLC
8615 Golden Spike Lane • Houston, Texas 77086
281.820.5493 • Fax 281.820.5499
800.434.4743 • www.geoproducts.org
Expanded
Collapsed
EGA2O (21.4') 6.52m
EGA3O (27.4') 8.35m
EGA4O (45') 13.72m
All Cell Sizes (8.4') 2.56m
3.6m
(12') Cell
Depth
Cell Depth
Cell
Width
127mm
(5")
Geo Products provides this information only as an accommodation to our customers. No warranty or other
representation regarding the suitability of the application procedure is made due to the fact that each
installation has specific requirements that may not have been considered in this generalized procedure.
Geo Products makes no warranties or representations regarding the suitability of its EnviroGrid for specific
uses or applications. Our liability is limited to furnishing, without charge, a replacement for
any EnviroGrid section that is proven defective under normal use and service.
Geo Products Quality System is
registered to ISO 9001:2000