Amr Mohamed Mahmoud El-Sayed Ayaad is an electrical power engineer with over 10 years of experience in substation design, testing, and commissioning in Egypt and Saudi Arabia. He holds a B.Sc. in Electrical Engineering from Cairo University with a focus on electrical power and machines. His career includes work as a secondary design senior engineer, testing and commissioning coordinator, and testing and commissioning engineer for high and medium voltage substations. He has extensive experience working with protection schemes and relay testing for substations up to 380kV. He is proficient in computer skills and software related to substation design, commissioning, and relay programming.

1. Page 1 of 5
Amr Mohamed Mahmoud El-Sayed Ayaad
16 al-Safa & al-Marwa St, Fisal St, Giza, Egypt
amrayaad194@hotmail.com
MOBILE: (202)01143032380
Home: (202) 33861378
Objective:-
Highly motivated Electrical Power Engineer, seeking a challenging job in a good reputation company, whereby my
knowledge and skills are fully developed.
I strongly believe that my past work experience along with my qualifications would be a valuable asset for your
organization.
Educational details:-
 B.Sc. in Electrical Engineering - Cairo University, Cairo, Egypt- July 2009
 Major: Electrical Power and Machines Engineering.
 Cumulative Grade: Very Good. 84% (Very Good with the first honor of degree)
 Graduation Year Grade: Excellent.
- Graduation Project Grade: Excellent (Chemical Mixing Automation using PLC&DAC and SCADA
system.
Work Experiences:-
1- Secondary Design Senior Engineer of High Voltage Substations.
(Bahrawy Consultancy Group BCG CO, Cairo, Egypt (Jan 2016 Till Now)
- Work Scope:
 Operational Single Line Diagram (OSLD) & Protection Single Line Diagram (PLD).
 Interlocking Logic Diagram, Point List (SAS, TFR, SOE, SCADA), Control Cables BOQ.
 CT&VT Sizing Calculations for Metering and Protection Cores.
 Relay Setting Calculations.
 Interfacing Drawing and Cable Termination Schedule.
I. Al Remal 8340; 132-13.8Kv Contractor: Capital Light Company.
II. Al Dawadmy Housing 8610; 132-13.8kV Contractor: AL-Shreef Group Company.
III. Al Nakheel 110-13.8 kv Substation Contractor: AL-Mashariq Group Company.
IV. Al-Fayha 110-13.8 kv Substation Contractor: AL-Mashariq Group Company.
V. Lajwan 33-13.8KV Substation Contractor: SIEMENS Company.
VI. Um Al Salam-2 110-13.8 kv Substation Contractor: AL-GIHAZ Company.
VII. University-3 110-13.8 kv Substation Contractor: AL-GIHAZ Company.
VIII. Jeddah Park 110-13.8 kv Substation Contractor: PSP Company.

2. Page 2 of 5
2- Testing and Commissioning Coordinator of High Voltage Substations.
(AL-FANAR CO, Al-Riyadh, Kingdom Of Saudi Arabia (MAY-2015 – Jan. 2016)
I. New Islamic University Substation (110/13.8 KV)-AlMadinah-Contractor: AL-FANAR (From MAY-2015 Till
November 2015).
II. Baydaa-2 Substation (110/13.8 KV)-AlMadinah-Contractor: ALSTOM (From November 2015 Till Jan 2016).
3-Testing and Commissioning Engineer of High Voltage and Medium Voltage Substations
(AL-FANAR CO, Al-Riyadh, Kingdom Of Saudi Arabia (March 2010 – Apr. 2015)
I. ALSALAM Substation (380/110/13.8 KV)-AlMadinah-Contractor :ALSTOM (From 5/6/2014 Till 30/4/2015)
II. MAKKAH NORTH substation- Makkah AL-Mokaramah (380/110/13.8KV) (2 Months)
III. HHR1 Harmeen Rail way substation –JEDDAH (One of the Biggest Substation in KSA) 380/110/33/13.8KV
(1 Month)
IV. JEDDAH NORTH substation-Jeddah(380/110/13.8KV) (1 Month)
V. HHR3 Harmeen Rail way substation-Jeddah(380/33KV) (3 Months)
VI. HHR6 Harmeen Rail way substation-MADINAH(380/33KV) (6 Months)
VII. HHR5 Harmeen Rail way substation-MADINAH(380/33KV) (4 Months)
VIII. HHR2 Harmeen Rail way substation –JEDDAH (One of the Biggest Substation in KSA) 380/110/33/13.8KV
(4 Months)
IX. 110/13.8Kv Tiaba University Substation / Al –Madinah AL-Monawara - Contractor :SIEMENS (7 Months)
X. SHAROURAH power plant - Contractor : ALFANAR ( 1 Month)
XI. JEC(Jazan Economic City) 380KV/132/13.8KV - Contractor : ALFANAR ( 10 Months)
XII. MAKKAH WEST substation 380KV/110/13.8KV- Makkah AL-Mokaramah- Contractor : ALFANAR
(11 Months )
- Work Scope in This Substations:
 380Kv ABB GIS functions and operation commissioning check.
 132Kv HYUNDIA GIS functions and operation commissioning check.
 110Kv Siemens GIS functions and operation commissioning check.
 13.8Kv ABB &Siemens Switch gear Functions and operation commissioning check.
 ACDB and DCDB panels Functions and operation commissioning check.
- Good Known about whole GIS and Switch gear testing types such as :-
 Current Transformer Testing
 Voltage transformer testing
 Contact resistance testing
 Circuit breaker testing ( Timing test and Insulation Test)
 Gas Leakage Test and Gas Density Switch test
 GIS and Switch gear current transformer stability test.
 Earth Switch insulation Leakage Current test.
- Good Known about protection and Control schemes & function check such as:-
 Circuit Breaker synchronizing protection scheme.
 Circuit Breaker fail protection scheme.
 Power Transformer protection scheme.

3. Page 3 of 5
 Power Transformer On load tap changer protection scheme.
 MOSIC CONTROL &MIMIC Scheme Commissioning Check.
 Over Head Transmission Line Protection Scheme Commissioning Check.
 Bus Bar low/high impedance Protection Scheme Commissioning Check.
 Bus section & Bus coupler protection Scheme Commissioning Check.
 Good Known about Low Voltage Panels schemes & function check such as:-
 MCB TEST & AUX RELAYS TEST
 MCCB TEST
 Testing for over current, Earth Fault & Under voltage relays.
 FULL Scheme Commissioning Check for 2 out of 3 scheme and all other schemes types.
 Good Known about protection relays testing such as:-
 Preparing Siemens relays configuration for SAS using CFC for all Siemens relays types and
testing it
 ABB relays configuration using application configuration for all ABB relays types
 MICOM relays configuration using PSL for all MICOM relays types
 Siemens Differential With Build in Distance relay ( 7SD522/7SA522(Distance relay))
 ABB Differential With Build in Distance relay ( RED670/REL670(Distance relay))
 ALSTOM Differential with Build in Distance relay ( MICOM P545,P546,P443(Distance
relay))
 SEL Differential with Build in Distance relay (SEL-411L).
 SEL over Current & Earth Fault & Neutral Unbalance relay & Trafo. Differential (SEL-
487V).
 GE Over/Under Voltage relay (C70).
 SIEMENS Power Transformer Differential Relay (7UT611)
 SIEMENS Motor Protection Relay (7UM )
 ABB REB500 (Bus Bar Protection)
 ABB over current relay (REF 615)
 ALSTOM over current relay and Thermal Overload ( P142 )
 Siemens over current relay (7SJ600).
 SEL Over Current ,Over Voltage& Under Voltage relay (451)
 SIEMENS over current relay (ARGOUS)
 ALSTOM HIGH IMPEDANCE DIFFRENTIAL RELAYS (MFAC)
 SIEMENS HIGH IMPEDANCE DIFFRENTIAL RELAYS (7VH)
 ARIVA Synchronizing Relay (KAVS100)
 Siemens under/over voltage relay (7VK61)
 Siemens Synchronizing relay (7VK61)
 Power Transformer on load tap changer relay (TAPCON 260)
 Power Transformer on load tap changer relay (ZIV)
Preparing CID for SAS (Substation Automation System)

4. Page 4 of 5
4‐ Teaching Assistant (Instructor) in Academy of Aviation Engineering and Technology from Oct.
2009 till March 2010.
Teaching courses: Electronics, power Electronics, Mathematics and electrical power laboratory.
Training:-
 2006: Summer Training in West Cairo Generation Station Transmission lines-Transformer-C.B-Protection
 2007: Summer Training in Micro Controller PIC 16f in communications & Electronics Club for Engineers
Cairo Uni.
 2007: Summer Training in Dispatch Center -Egyptian Electricity Transmission Company – Control System
Department.
 2008: Summer Training in ABB Arab Company - Transformer-C.B-Fuses-Protection-Ring main unit.
Technical courses:-
 2008: Course PLC (ABB) &SCADA System (i-fix).
 2008: Course AutoCAD-2D.
Objectives for the mean time:
 Have Real work Experience.
 Develop new Skills.
 Live the Atmosphere of a Successful organization.
 Broadening the way I think by meeting new People and going to new Places.
 Have new Experiences.
 Ability to get familiar with complex and new software and hardware tools.
 Utmost utilization of knowledge acquired.
 Fast integration into new work teams.
 Pleasant and well Deserved confidence personality
Computer Skills:-
 AutoCAD.
 MicroStation.
 Microsoft Word, Excel, PowerPoint and Outlook.
 Matlab.
 PLC Programming.
 DIGSI 4.89 (Siemens Relay Interface Programming)
 MICOM Agile (ALSTOM Relay Interface Programming)
 PCM600 ( ABB Relay Interface Programming)
 AcSELerator QuickSet. (SEL Relay Interface Programming)
 Enervista UR (GE Relay Interface Programming)
 ZiverComPlus/ ZIVerCID (ZIV Relay Interface Programming)
Language skills:-
 Arabic: Mother language.
 English: very good spoken and written.
 Deutsch: Fair.

5. Page 5 of 5
Hobbies:-
 Reading & Internet searching.
Personal Details:-
 Date of Birth: 2/8/1987.
 Gender: Male.
 Nationality: Egyptian.
 Marital status: Married.
 Military Status: Exempted.
ALL MY DOCUMENTS ARE AVAILABLE WHEN REQUESTED