Abstract: Human society’s need to build low-weight, high-strength and durable structures has
increased the demand for composite materials. In this case, composites are used where high mechanical strength, low weight, sound and thermal insulation properties are required. One of the most
important issues now is designing materials and coatings aimed at reducing heat loss and resisting
high temperatures. One way to address this problem is to develop a technique for preparing and
applying composite materials that slow down their heating applied to a surface. In this study, carbon
nanotubes (CNTs) reinforced composites were fabricated using silicone molding to be applied to
honeycomb sandwich structures. To determine the effect of CNTs on the thermal behavior of the
sandwich panels, different weight percentages of this material (0.025, 0.05. 0.075 wt.%) were added to
the epoxy resin. The results showed that the thermal stability of the epoxy composites was directly
related to the increase in the percentage of CNTs as the CNT content increased to 0.075 wt.%, and the
thermal degradation temperature of the epoxy composites increased by 14 ◦C. In addition, the energy
absorption increased by 4.6% with an increase in CNTs up to 0.075 wt.%. Density measurements
showed that the density of the nanocomposite samples increased by adding CNTs to pure epoxy
resin. The actual densities of the samples reinforced with 0.025, 0.05, and 0.075 wt.% CNTs are 0.925,
0.926, and 0.927 of the theoretical density, respectively. Since the CNT dispersion uniformity in the
epoxy matrix can significantly affect the properties of the composites, in this study, a new method of
dispersing CNTs in the epoxy resin matrix resulted in higher thermal conductivity while using lower
amounts of CNTs compared to other studies. The storage modulus of the epoxy matrix composites
reinforced with 0.05 wt.% in this study was 25.9% and 6.9% higher than that from the previous study
reinforced with 0.1 wt.% and 0.25 wt.% CNTs, respectively. Furthermore, the tanδ and loss modulus
of the composite reinforced with 0.05 wt.% CNTs in this study were 52% and 54.5% higher than that
from the previous study with 0.1 wt.% CNTs, respectively. This study provided an optimal approach
for designers and engineers who want to effectively design their composite honeycomb sandwich
structure with better thermal properties.
Keywords: epoxy composites; carbon nanotubes (CNTs); thermal stability; energy absorption;
density; honeycomb sandwich structure; CNT dispersion
A comparative study on the influence of MWCNT, GO, and Al(OH)3 gel matrix mo...Adib Bin Rashid
The main objective of this paper was to identify the influence of different filler materials on the properties of hybrid composites. The hybrid composites were fabricated using randomly oriented glass fiber mats, needle punched jute fiber mats, and epoxy resin as the matrix material. Three different kinds of filler materials were studied: Multi-Walled Carbon Nanotubes (MWCNTs), Graphene Oxide (GO), and Aluminum Hydroxide (AlOH)
nanoparticles. The secondary reinforcements were dispersed in the epoxy matrix through ultrasonication. The
composites were made by conventional hand lay-up followed by applying high pressure and temperature under a hydraulic press to effectively cure and minimize voids within the final composite. These were compared with the
properties of the unmodified composite containing no filler. The influence on mechanical properties was evaluated through tensile, flexural, and impact tests. Failure modes of the fractured tensile specimen were observed
through Scanning Electron Microscopy (SEM). Fourier Transform Infrared (FTIR) analysis was done to observe
the changes in the chemical structure upon the addition of secondary reinforcements. Lastly, water absorption
behavior and flame retardancy were observed as well. The results showed that MWCNT resulted in the composite
exhibiting superior properties and GO, on the contrary, led to the deterioration of the properties. This could be
because an optimum concentration of MWCNT was used, whereas this was not the case for GO filler. The addition
of MWCNT resulted in a more substantial but brittle composite, while AlOH enhanced the ductility of the
composite by compromising the overall strength. Hence, it can be concluded that MWCNT resulted in the formation of composites with the most desired properties.
MPA_Review of Carbon Nanotube Applications, Synthesis Methods and Processes f...SheongWei NG
This document discusses carbon nanotubes (CNTs), including their applications, synthesis methods, and processes for mass production. It begins by introducing CNTs and their remarkable properties. It then outlines some of their applications in areas like composite materials, energy storage, and the environment. The document reviews various synthesis methods, particularly arc discharge, laser ablation, and chemical vapor deposition. It discusses processes that have been developed for large-scale CNT production, such as the high-pressure carbon monoxide and cobalt-molybdenum catalytic processes. The goal is mass producing CNTs with desired properties and organized architectures at an industrial scale.
This document discusses fabricating copper-carbon nanotube (Cu/CNT) composites using powder metallurgy techniques. It first provides motivation for developing materials with enhanced properties like lower friction. It then reviews literature showing CNTs can improve properties like strength and thermal conductivity in metal matrices. The document outlines a process to coat CNTs with nickel via electroless plating before mixing with copper powder and sintering. Testing will examine how added CNTs affect hardness, wear rate, and porosity. The expected results are that CNTs will reduce wear coefficients by enhancing properties like hardness. Potential applications of the Cu/CNT composites include bearings, electrical brushes, and brakes where properties like
Effects of Carbon Nanotubes on the Compressive and Flexural Strength and Micr...LidaN16
Abstract—The needs of the human communities to build low weight, high strength and durable structures
have increased the demand for composite materials, including sandwich structures. In this case, sandwich
panels are used in situations requiring high mechanical strength, low weight, sound insulation and thermal
insulation properties. In this study, carbon nanotubes-reinforced composite honeycomb sandwich panels
were constructed using silicone molding. To determine the role of carbon nanotubes on the compressive
and bending behavior of sandwich panels, different amount of nanotubes was added to the epoxy resin.
Also, different thicknesses were tested to determine the role of core wall thickness on the compressive and
bending behavior of sandwich panels. The results showed that the compressive strength of honeycomb panels has a direct relation with the increase in the percentage of carbon nanotubes and the thickness of the
wall. The compressive strength of sandwich panels increased from 42 up to 54 MPa with increasing carbon
nanotubes from 0.025 up to 0.075 wt %. The compressive strength of sandwich panels with 5 mm honeycomb wall thickness and reinforced with 0.025, 0.05, and 0.075 wt % of carbon nanotubes compared to
sandwich panels with 2.5 mm honeycomb wall thickness was respectively 2.4, 2.1, and 2.2 times. The flexural strength of 5-mm honeycomb wall thickness and reinforced with 0.025, 0.05, and 0.075 wt % of carbon
nanotubes compared to sandwich panels with 2.5 mm honeycomb wall thickness, were respectively 3, 2.7,
and 2.7 times.
Synthesis Of Various Forms Of Carbon Nanotubes by ARC Discharge Methods – Com...IRJET Journal
This document reviews various methods for synthesizing carbon nanotubes, specifically arc discharge, laser ablation, and chemical vapor deposition. It discusses the structure of single-walled and multi-walled carbon nanotubes and how they are formed. It also reviews research on reinforcing aluminum matrix composites with carbon nanotubes to improve mechanical properties like strength and stiffness. Strengthening mechanisms for aluminum-carbon nanotube composites include thermal mismatching, Orowan looping, and shear lag effects between the matrix and reinforcement.
Review on Molecular Dynamics Simulations of Effects of Carbon Nanotubes (CNTs...LidaN16
The document summarizes research on molecular dynamics (MD) simulations that analyze the effects of various factors on the thermal and electrical conductivity of carbon nanotube (CNT)-modified polymer composites. Specifically, it discusses how MD simulations have shown that CNT chirality, length, hydrogen bonding, and overlap length can impact conductivity. For CNT chirality, the simulations demonstrated that zigzag CNTs have lower conductivity than armchair CNTs, and the effect of chirality decreases with increasing length. Hydrogen bonding was also found to affect composite conductivity by allowing better electron/phonon transport along CNTs.
This document discusses the fabrication and evaluation of a polymer matrix composite reinforced with aligned carbon nanotubes. The objective is to create a lightweight composite material with high strength, thermal and electrical conductivity. Key challenges include dispersing and aligning the carbon nanotubes in the polymer matrix. The composite will be made using polyvinylidene fluoride matrix with functionalized carbon nanotubes. Different compositions will be characterized to evaluate morphology, mechanical properties, and electrical conductivity both along and across the alignment direction. Potential applications of the composite include structural materials, printed circuit boards, and conductive coatings.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
A comparative study on the influence of MWCNT, GO, and Al(OH)3 gel matrix mo...Adib Bin Rashid
The main objective of this paper was to identify the influence of different filler materials on the properties of hybrid composites. The hybrid composites were fabricated using randomly oriented glass fiber mats, needle punched jute fiber mats, and epoxy resin as the matrix material. Three different kinds of filler materials were studied: Multi-Walled Carbon Nanotubes (MWCNTs), Graphene Oxide (GO), and Aluminum Hydroxide (AlOH)
nanoparticles. The secondary reinforcements were dispersed in the epoxy matrix through ultrasonication. The
composites were made by conventional hand lay-up followed by applying high pressure and temperature under a hydraulic press to effectively cure and minimize voids within the final composite. These were compared with the
properties of the unmodified composite containing no filler. The influence on mechanical properties was evaluated through tensile, flexural, and impact tests. Failure modes of the fractured tensile specimen were observed
through Scanning Electron Microscopy (SEM). Fourier Transform Infrared (FTIR) analysis was done to observe
the changes in the chemical structure upon the addition of secondary reinforcements. Lastly, water absorption
behavior and flame retardancy were observed as well. The results showed that MWCNT resulted in the composite
exhibiting superior properties and GO, on the contrary, led to the deterioration of the properties. This could be
because an optimum concentration of MWCNT was used, whereas this was not the case for GO filler. The addition
of MWCNT resulted in a more substantial but brittle composite, while AlOH enhanced the ductility of the
composite by compromising the overall strength. Hence, it can be concluded that MWCNT resulted in the formation of composites with the most desired properties.
MPA_Review of Carbon Nanotube Applications, Synthesis Methods and Processes f...SheongWei NG
This document discusses carbon nanotubes (CNTs), including their applications, synthesis methods, and processes for mass production. It begins by introducing CNTs and their remarkable properties. It then outlines some of their applications in areas like composite materials, energy storage, and the environment. The document reviews various synthesis methods, particularly arc discharge, laser ablation, and chemical vapor deposition. It discusses processes that have been developed for large-scale CNT production, such as the high-pressure carbon monoxide and cobalt-molybdenum catalytic processes. The goal is mass producing CNTs with desired properties and organized architectures at an industrial scale.
This document discusses fabricating copper-carbon nanotube (Cu/CNT) composites using powder metallurgy techniques. It first provides motivation for developing materials with enhanced properties like lower friction. It then reviews literature showing CNTs can improve properties like strength and thermal conductivity in metal matrices. The document outlines a process to coat CNTs with nickel via electroless plating before mixing with copper powder and sintering. Testing will examine how added CNTs affect hardness, wear rate, and porosity. The expected results are that CNTs will reduce wear coefficients by enhancing properties like hardness. Potential applications of the Cu/CNT composites include bearings, electrical brushes, and brakes where properties like
Effects of Carbon Nanotubes on the Compressive and Flexural Strength and Micr...LidaN16
Abstract—The needs of the human communities to build low weight, high strength and durable structures
have increased the demand for composite materials, including sandwich structures. In this case, sandwich
panels are used in situations requiring high mechanical strength, low weight, sound insulation and thermal
insulation properties. In this study, carbon nanotubes-reinforced composite honeycomb sandwich panels
were constructed using silicone molding. To determine the role of carbon nanotubes on the compressive
and bending behavior of sandwich panels, different amount of nanotubes was added to the epoxy resin.
Also, different thicknesses were tested to determine the role of core wall thickness on the compressive and
bending behavior of sandwich panels. The results showed that the compressive strength of honeycomb panels has a direct relation with the increase in the percentage of carbon nanotubes and the thickness of the
wall. The compressive strength of sandwich panels increased from 42 up to 54 MPa with increasing carbon
nanotubes from 0.025 up to 0.075 wt %. The compressive strength of sandwich panels with 5 mm honeycomb wall thickness and reinforced with 0.025, 0.05, and 0.075 wt % of carbon nanotubes compared to
sandwich panels with 2.5 mm honeycomb wall thickness was respectively 2.4, 2.1, and 2.2 times. The flexural strength of 5-mm honeycomb wall thickness and reinforced with 0.025, 0.05, and 0.075 wt % of carbon
nanotubes compared to sandwich panels with 2.5 mm honeycomb wall thickness, were respectively 3, 2.7,
and 2.7 times.
Synthesis Of Various Forms Of Carbon Nanotubes by ARC Discharge Methods – Com...IRJET Journal
This document reviews various methods for synthesizing carbon nanotubes, specifically arc discharge, laser ablation, and chemical vapor deposition. It discusses the structure of single-walled and multi-walled carbon nanotubes and how they are formed. It also reviews research on reinforcing aluminum matrix composites with carbon nanotubes to improve mechanical properties like strength and stiffness. Strengthening mechanisms for aluminum-carbon nanotube composites include thermal mismatching, Orowan looping, and shear lag effects between the matrix and reinforcement.
Review on Molecular Dynamics Simulations of Effects of Carbon Nanotubes (CNTs...LidaN16
The document summarizes research on molecular dynamics (MD) simulations that analyze the effects of various factors on the thermal and electrical conductivity of carbon nanotube (CNT)-modified polymer composites. Specifically, it discusses how MD simulations have shown that CNT chirality, length, hydrogen bonding, and overlap length can impact conductivity. For CNT chirality, the simulations demonstrated that zigzag CNTs have lower conductivity than armchair CNTs, and the effect of chirality decreases with increasing length. Hydrogen bonding was also found to affect composite conductivity by allowing better electron/phonon transport along CNTs.
This document discusses the fabrication and evaluation of a polymer matrix composite reinforced with aligned carbon nanotubes. The objective is to create a lightweight composite material with high strength, thermal and electrical conductivity. Key challenges include dispersing and aligning the carbon nanotubes in the polymer matrix. The composite will be made using polyvinylidene fluoride matrix with functionalized carbon nanotubes. Different compositions will be characterized to evaluate morphology, mechanical properties, and electrical conductivity both along and across the alignment direction. Potential applications of the composite include structural materials, printed circuit boards, and conductive coatings.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
This document discusses carbon nanotubes (CNTs), including their discovery, structure, properties, synthesis, applications, and future potential. Some key points:
- CNTs were discovered in 1991 and have a rolled-up graphene sheet structure that gives them unique mechanical and electrical properties.
- CNTs exhibit extraordinary strength and conductivity, with current-carrying capacity 1000 times higher than copper.
- Common synthesis methods are arc discharge, laser ablation, and chemical vapor deposition.
- Applications include energy storage, conductive composites, electronics, and more. Mass production is increasing and CNTs are already used in some products.
- CNTs show promise for applications across many industries
This document reviews the use of nanotechnology in the construction industry. It discusses how nanotechnology is being used to improve concrete in several ways, such as adding nanoparticles like nano-silica to increase strength and durability. Carbon nanotubes are also being researched as an additive to increase concrete's strength, stiffness, and energy absorption capabilities. Nanotechnology enables self-compacting concrete that does not require vibration during pouring and self-healing concrete that can repair minor cracks. Overall, the document outlines various applications of nanotechnology in construction materials and structures to enhance performance.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Analyzing the Microstructural Properties of Nanomaterial in OPC by SEM, TEM, ...IRJET Journal
This document discusses the use of nanomaterials like nano silica and carbon nanotubes in ordinary Portland cement. It analyzes the microstructural properties using SEM, TEM, XRD techniques and corrosion rate using TAFEL techniques. Ordinary Portland cement was substituted with 1% nano silica by weight and carbon nanotubes were added in ratios from 0.01% to 0.07% by weight. The blended cement mortar was tested and previous studies found that nano silica and carbon nanotubes can improve the mechanical properties and durability of cement composites. The document reviews literature that analyzed how nano silica and carbon nanotubes fill pores, improve microstructure, increase strength and reduce permeability.
This document summarizes a study on the effect of environmental degradation on the viscoelastic response of epoxy resins modified with carbon nanotubes (CNTs) and carbon fiber reinforced plastics (CFRPs) made with the modified epoxy. CNTs were added to an epoxy resin at concentrations from 0.1-1% using high-shear mixing. The modified resin was used to make unreinforced cast specimens and CFRPs with a 0.5% CNT content. All specimens were subjected to hydrothermal conditioning. Dynamic mechanical analysis of the conditioned specimens showed degradation of properties like damping and storage modulus for the modified materials compared to unmodified controls.
Nanotechnology Carbon Nanotubes (CNTs) Research PaperMohammed Aqeel
Carbon nanotubes are an emerging nanotechnology that were discovered accidentally in 1991. They are cylindrical structures made of carbon atoms that have extraordinary thermal and electrical conductivity as well as mechanical strength. There are currently three main methods for producing carbon nanotubes, with catalytic chemical vapor deposition being the most promising for mass production. While carbon nanotubes show potential for a wide range of applications, their use has been limited due to the complex, expensive production methods and inability to manufacture very long or defect-free nanotubes. Researchers are working to address these challenges and find ways to incorporate carbon nanotubes into composite materials to make products stronger and lighter.
Carbon Nanotubes Effect for Polymer Materials on Break Down Voltage IJECEIAES
Epoxy resin composites reinforced to different types of carbon nano-particles have been fabricated. Carbon black (20, 30 and 40 wt. %), graphene (0.5 to 4 wt. %) and carbon nanotubes (CNT) (0.5 to 2 wt. %) were added with different weight percentages to epoxy. The dielectric strength of composites was tested in several conditions such as (dry, wet, low salinity and high salinity). The mechanical characterization showed that the nano-composite Polymer enhanced by using these particles in the tensile strength. Thermal gravimetric analysis shows effect of these nano-particles on the thermal structure of epoxy resin. Scanning Electron Microscopic test is used to characterize the dispersion of carbon nano-particles and to analysis the fractured parts in the nano scale.
The document experimentally investigates carbon nanotube (CNT) infused glass fiber reinforced polymer (GFRP) hollow box beams. GFRP hollow box beams were fabricated using hand lay-up and vacuum bagging with varying weight percentages of multiwalled CNTs (0%, 0.5%, 1%). Three-point bending and edgewise compression tests were performed on the beams. The results showed that the bending stress was highest for the beam with 1% CNT infusion at 81.1 MPa. Meanwhile, the maximum compressive stress was highest for the beam with 0.5% CNT infusion at 85.371 MPa. In conclusion, the addition of CNTs improved the mechanical properties of G
functionalized multi walled carbon nanotube-reinforced epoxy-composites elec...INFOGAIN PUBLICATION
This document summarizes research on functionalized multi-walled carbon nanotube (f-MWCNT)-reinforced epoxy composites. Different weight percentages of f-MWCNTs (1-4%) were added to epoxy resin and characterized. Scanning electron microscopy showed uniform f-MWCNT dispersion up to 4% weight, with increased surface roughness. Raman spectroscopy confirmed the presence of f-MWCNTs through D and G bands. Electrical resistivity of the epoxy decreased from 108 to 103 Ω.m with f-MWCNT additions from 1-4% due to improved conductivity pathways. Hardness increased by 20.7-29.09% with 1-4% f-
A Review Paper On Properties Of Carbon Fiber Reinforced PolymersAmy Cernava
1) The document reviews properties of carbon fiber reinforced polymers (CFRPs), which are lightweight composite materials stronger than conventional materials.
2) It discusses how adding nanoparticles like carbon nanotubes and nanoclays can improve mechanical properties of CFRPs. Testing shows flexural stress and impact resistance increase with nanoparticles.
3) Non-destructive testing methods like eddy current pulsed thermography are used to study CFRP properties under impact loading. Thermograms show the effect of impacts on temperature responses at different material points.
Influence of low temperature on heat transfer in epoxide nano compositesAlexander Decker
This document summarizes research on the influence of low temperatures on heat transfer in epoxide
nanocomposites. It discusses how adding nanofillers to epoxy polymers can significantly change their
mechanical, thermal, and electrical properties due to increased heterogeneity and interactions at the
polymer-filler interface. The document also describes the preparation and testing of epoxy nanocomposite
samples containing various nanofillers like carbon nanotubes and aerosil at low concentrations.
Influence of low temperature on heat transfer in epoxide nano compositesAlexander Decker
This document summarizes research on the influence of low temperatures on heat transfer in epoxide
nanocomposites. It discusses how adding nanofillers to epoxy polymers can significantly change their
mechanical, thermal, and electrical properties due to increased heterogeneity and interactions at the
polymer-filler interface. The document also describes the preparation and testing of epoxy nanocomposite
samples containing various nanofillers like carbon nanotubes and aerosil at low concentrations.
Fabrication and Mechanical Charecterization of Cnt NanocompositesIOSR Journals
This document discusses the fabrication and mechanical characterization of carbon nanotube (CNT) nanocomposites. Multi-walled carbon nanotubes were functionalized with amine and epoxide groups and then mixed with epoxy resin to create nanocomposites at various CNT loadings. The mechanical properties of the nanocomposites, including flexural strength, flexural modulus, and interlaminar shear strength, were tested and compared to a control composite without CNTs. Fourier transform infrared spectroscopy was used to confirm the functionalization of the CNTs. The results showed that amine-functionalized CNT composites generally had better mechanical properties than epoxide-functionalized or
International Journal of Research in Engineering and Science is an open access peer-reviewed international forum for scientists involved in research to publish quality and refereed papers. Papers reporting original research or experimentally proved review work are welcome. Papers for publication are selected through peer review to ensure originality, relevance, and readability.
This document summarizes an experimental investigation into the reinforcement of metal matrix composites with multiwalled carbon nanotubes to improve fatigue life. Glass fiber composites currently have high strength but poor fatigue performance due to matrix cracking. The study found that adding only 1% of carbon nanotubes by weight significantly increased the high-cycle fatigue life of glass fiber composites. Carbon nanotubes were found to inhibit crack formation and growth by nucleating many nano-scale damage zones. Energy absorption also increased through nanotube pullout and fracture. An energy-based model was proposed to explain the fatigue life improvement from additional strain energy absorption in the composite.
Actuating carbon nanotube nanocomposite skins for aerospace applicationsJoe Dolby
This document discusses a project report by Joseph Dolby from the University of Surrey on actuating carbon nanotube nanocomposite skins for aerospace applications. It provides background on carbon nanotubes, previous research on electrofunctional polymer nanocomposites, and the objectives of Dolby's project. The project aims to create a flexible polymer matrix with carbon nanotubes to reduce aircraft skin friction drag and enable changing wing shape. It will measure the material's capacitance, test for actuation under voltage, and potential application to aircraft wings.
Carbon nano tubes for concrete better constructionsriram1052
The document summarizes a presentation on the compressive strength and microstructure of carbon nanotubes-fly ash cement composites. It discusses adding different amounts of carbon nanotubes (CNTs) to fly ash cement mixtures and testing the density, compressive strength, and microstructure of the resulting composites. Testing included SEM, XRD, TGA, DTA, and EDS analyses. The results showed that adding 0.5-1.0% CNTs increased the density and compressive strength of the fly ash cement composites compared to mixtures without CNTs. Microstructural analysis revealed the CNTs were uniformly dispersed in the cement matrix.
Potential enhancement of thermoelectric energy conversion in cobaltite superl...Anastasios Englezos
This document is a master's thesis submitted by Tasos Englezos investigating the potential enhancement of thermoelectric energy conversion in cobaltite oxide superlattices. The thesis aims to grow superlattices composed of alternating layers of NaxCoO3 and Ca3Co4O9 using pulsed laser deposition, as both materials show promise for thermoelectric applications but also have limitations. Characterization of the superlattices shows the structures maintain crystalline coherence while electrical and thermal properties are preserved at a good level. Further measurements of thermal conductivity are needed to determine if the superlattice approach reduces thermal conductivity and thereby improves thermoelectric efficiency in these cobaltite oxides.
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...IJECEIAES
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
More Related Content
Similar to Effect of carbon nanotube on thermal behavior of epoxy resin composites
This document discusses carbon nanotubes (CNTs), including their discovery, structure, properties, synthesis, applications, and future potential. Some key points:
- CNTs were discovered in 1991 and have a rolled-up graphene sheet structure that gives them unique mechanical and electrical properties.
- CNTs exhibit extraordinary strength and conductivity, with current-carrying capacity 1000 times higher than copper.
- Common synthesis methods are arc discharge, laser ablation, and chemical vapor deposition.
- Applications include energy storage, conductive composites, electronics, and more. Mass production is increasing and CNTs are already used in some products.
- CNTs show promise for applications across many industries
This document reviews the use of nanotechnology in the construction industry. It discusses how nanotechnology is being used to improve concrete in several ways, such as adding nanoparticles like nano-silica to increase strength and durability. Carbon nanotubes are also being researched as an additive to increase concrete's strength, stiffness, and energy absorption capabilities. Nanotechnology enables self-compacting concrete that does not require vibration during pouring and self-healing concrete that can repair minor cracks. Overall, the document outlines various applications of nanotechnology in construction materials and structures to enhance performance.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Analyzing the Microstructural Properties of Nanomaterial in OPC by SEM, TEM, ...IRJET Journal
This document discusses the use of nanomaterials like nano silica and carbon nanotubes in ordinary Portland cement. It analyzes the microstructural properties using SEM, TEM, XRD techniques and corrosion rate using TAFEL techniques. Ordinary Portland cement was substituted with 1% nano silica by weight and carbon nanotubes were added in ratios from 0.01% to 0.07% by weight. The blended cement mortar was tested and previous studies found that nano silica and carbon nanotubes can improve the mechanical properties and durability of cement composites. The document reviews literature that analyzed how nano silica and carbon nanotubes fill pores, improve microstructure, increase strength and reduce permeability.
This document summarizes a study on the effect of environmental degradation on the viscoelastic response of epoxy resins modified with carbon nanotubes (CNTs) and carbon fiber reinforced plastics (CFRPs) made with the modified epoxy. CNTs were added to an epoxy resin at concentrations from 0.1-1% using high-shear mixing. The modified resin was used to make unreinforced cast specimens and CFRPs with a 0.5% CNT content. All specimens were subjected to hydrothermal conditioning. Dynamic mechanical analysis of the conditioned specimens showed degradation of properties like damping and storage modulus for the modified materials compared to unmodified controls.
Nanotechnology Carbon Nanotubes (CNTs) Research PaperMohammed Aqeel
Carbon nanotubes are an emerging nanotechnology that were discovered accidentally in 1991. They are cylindrical structures made of carbon atoms that have extraordinary thermal and electrical conductivity as well as mechanical strength. There are currently three main methods for producing carbon nanotubes, with catalytic chemical vapor deposition being the most promising for mass production. While carbon nanotubes show potential for a wide range of applications, their use has been limited due to the complex, expensive production methods and inability to manufacture very long or defect-free nanotubes. Researchers are working to address these challenges and find ways to incorporate carbon nanotubes into composite materials to make products stronger and lighter.
Carbon Nanotubes Effect for Polymer Materials on Break Down Voltage IJECEIAES
Epoxy resin composites reinforced to different types of carbon nano-particles have been fabricated. Carbon black (20, 30 and 40 wt. %), graphene (0.5 to 4 wt. %) and carbon nanotubes (CNT) (0.5 to 2 wt. %) were added with different weight percentages to epoxy. The dielectric strength of composites was tested in several conditions such as (dry, wet, low salinity and high salinity). The mechanical characterization showed that the nano-composite Polymer enhanced by using these particles in the tensile strength. Thermal gravimetric analysis shows effect of these nano-particles on the thermal structure of epoxy resin. Scanning Electron Microscopic test is used to characterize the dispersion of carbon nano-particles and to analysis the fractured parts in the nano scale.
The document experimentally investigates carbon nanotube (CNT) infused glass fiber reinforced polymer (GFRP) hollow box beams. GFRP hollow box beams were fabricated using hand lay-up and vacuum bagging with varying weight percentages of multiwalled CNTs (0%, 0.5%, 1%). Three-point bending and edgewise compression tests were performed on the beams. The results showed that the bending stress was highest for the beam with 1% CNT infusion at 81.1 MPa. Meanwhile, the maximum compressive stress was highest for the beam with 0.5% CNT infusion at 85.371 MPa. In conclusion, the addition of CNTs improved the mechanical properties of G
functionalized multi walled carbon nanotube-reinforced epoxy-composites elec...INFOGAIN PUBLICATION
This document summarizes research on functionalized multi-walled carbon nanotube (f-MWCNT)-reinforced epoxy composites. Different weight percentages of f-MWCNTs (1-4%) were added to epoxy resin and characterized. Scanning electron microscopy showed uniform f-MWCNT dispersion up to 4% weight, with increased surface roughness. Raman spectroscopy confirmed the presence of f-MWCNTs through D and G bands. Electrical resistivity of the epoxy decreased from 108 to 103 Ω.m with f-MWCNT additions from 1-4% due to improved conductivity pathways. Hardness increased by 20.7-29.09% with 1-4% f-
A Review Paper On Properties Of Carbon Fiber Reinforced PolymersAmy Cernava
1) The document reviews properties of carbon fiber reinforced polymers (CFRPs), which are lightweight composite materials stronger than conventional materials.
2) It discusses how adding nanoparticles like carbon nanotubes and nanoclays can improve mechanical properties of CFRPs. Testing shows flexural stress and impact resistance increase with nanoparticles.
3) Non-destructive testing methods like eddy current pulsed thermography are used to study CFRP properties under impact loading. Thermograms show the effect of impacts on temperature responses at different material points.
Influence of low temperature on heat transfer in epoxide nano compositesAlexander Decker
This document summarizes research on the influence of low temperatures on heat transfer in epoxide
nanocomposites. It discusses how adding nanofillers to epoxy polymers can significantly change their
mechanical, thermal, and electrical properties due to increased heterogeneity and interactions at the
polymer-filler interface. The document also describes the preparation and testing of epoxy nanocomposite
samples containing various nanofillers like carbon nanotubes and aerosil at low concentrations.
Influence of low temperature on heat transfer in epoxide nano compositesAlexander Decker
This document summarizes research on the influence of low temperatures on heat transfer in epoxide
nanocomposites. It discusses how adding nanofillers to epoxy polymers can significantly change their
mechanical, thermal, and electrical properties due to increased heterogeneity and interactions at the
polymer-filler interface. The document also describes the preparation and testing of epoxy nanocomposite
samples containing various nanofillers like carbon nanotubes and aerosil at low concentrations.
Fabrication and Mechanical Charecterization of Cnt NanocompositesIOSR Journals
This document discusses the fabrication and mechanical characterization of carbon nanotube (CNT) nanocomposites. Multi-walled carbon nanotubes were functionalized with amine and epoxide groups and then mixed with epoxy resin to create nanocomposites at various CNT loadings. The mechanical properties of the nanocomposites, including flexural strength, flexural modulus, and interlaminar shear strength, were tested and compared to a control composite without CNTs. Fourier transform infrared spectroscopy was used to confirm the functionalization of the CNTs. The results showed that amine-functionalized CNT composites generally had better mechanical properties than epoxide-functionalized or
International Journal of Research in Engineering and Science is an open access peer-reviewed international forum for scientists involved in research to publish quality and refereed papers. Papers reporting original research or experimentally proved review work are welcome. Papers for publication are selected through peer review to ensure originality, relevance, and readability.
This document summarizes an experimental investigation into the reinforcement of metal matrix composites with multiwalled carbon nanotubes to improve fatigue life. Glass fiber composites currently have high strength but poor fatigue performance due to matrix cracking. The study found that adding only 1% of carbon nanotubes by weight significantly increased the high-cycle fatigue life of glass fiber composites. Carbon nanotubes were found to inhibit crack formation and growth by nucleating many nano-scale damage zones. Energy absorption also increased through nanotube pullout and fracture. An energy-based model was proposed to explain the fatigue life improvement from additional strain energy absorption in the composite.
Actuating carbon nanotube nanocomposite skins for aerospace applicationsJoe Dolby
This document discusses a project report by Joseph Dolby from the University of Surrey on actuating carbon nanotube nanocomposite skins for aerospace applications. It provides background on carbon nanotubes, previous research on electrofunctional polymer nanocomposites, and the objectives of Dolby's project. The project aims to create a flexible polymer matrix with carbon nanotubes to reduce aircraft skin friction drag and enable changing wing shape. It will measure the material's capacitance, test for actuation under voltage, and potential application to aircraft wings.
Carbon nano tubes for concrete better constructionsriram1052
The document summarizes a presentation on the compressive strength and microstructure of carbon nanotubes-fly ash cement composites. It discusses adding different amounts of carbon nanotubes (CNTs) to fly ash cement mixtures and testing the density, compressive strength, and microstructure of the resulting composites. Testing included SEM, XRD, TGA, DTA, and EDS analyses. The results showed that adding 0.5-1.0% CNTs increased the density and compressive strength of the fly ash cement composites compared to mixtures without CNTs. Microstructural analysis revealed the CNTs were uniformly dispersed in the cement matrix.
Potential enhancement of thermoelectric energy conversion in cobaltite superl...Anastasios Englezos
This document is a master's thesis submitted by Tasos Englezos investigating the potential enhancement of thermoelectric energy conversion in cobaltite oxide superlattices. The thesis aims to grow superlattices composed of alternating layers of NaxCoO3 and Ca3Co4O9 using pulsed laser deposition, as both materials show promise for thermoelectric applications but also have limitations. Characterization of the superlattices shows the structures maintain crystalline coherence while electrical and thermal properties are preserved at a good level. Further measurements of thermal conductivity are needed to determine if the superlattice approach reduces thermal conductivity and thereby improves thermoelectric efficiency in these cobaltite oxides.
Similar to Effect of carbon nanotube on thermal behavior of epoxy resin composites (20)
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...IJECEIAES
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
International Conference on NLP, Artificial Intelligence, Machine Learning an...gerogepatton
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODELgerogepatton
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...IJECEIAES
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Literature Review Basics and Understanding Reference Management.pptxDr Ramhari Poudyal
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024Sinan KOZAK
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
2. J. Compos. Sci. 2023, 7, 313 2 of 15
strength with low weight, make them suitable for architectural, aerospace, and military
applications [4]. Their high thermal conductivity makes them important for applications
such as electronics that require high thermal conductivity. Therefore, honeycomb sandwich
structures made of CNT-reinforced epoxy resin matrix can be used in applications that
require high flexural, strength, and thermal conductivity simultaneously, such as reusable
launch vehicles based on load-carrying structures [5] and ablative heat shields [6] that
require high strength and thermal conductivity.
In fact, sandwich panels are special types of multilayer composites. In this regard, a
sandwich structure consists of a lightweight, thick core covered by two high-strength thin
shells. The shells are usually very hard, while the inner core is relatively weak and flexible.
When combining them into a sandwich panel, a highly lightweight and rigid structure has
been built [7].
Epoxy resins are used in many applications, such as floor coverings, glues, coatings,
tool making and composites. Epoxy resins are widely used in composites and provide
desirable properties such as desirable strength and hardness, thermal stability, and strength
against chemical environments. Recently, researchers have started to study epoxy compos-
ites containing nanoparticles to analyze their physical, mechanical, and chemical properties.
In this context, the desirable properties obtained due to the addition of nanoparticles to
epoxy resins increase the tendency to use nanoparticles. Among many nano-reinforcements
used in the manufacture of nanocomposites, carbon nanotubes (CNTs) play an important
role in improving the physical and mechanical properties of epoxy resins, considering
their unique properties such as low density, high thermal conductivity, and high strength
and hardness. Currently, composite materials used for thermal fillers do not provide any
electrical properties. CNTs have excellent mechanical, thermal, and electrical properties.
CNTs have a strong crystal lattice, giving them good physical and thermal properties [8,9].
It can be observed from the literature that CNTs possess high electrical and ther-
mal conductivity as well as excellent mechanical properties [10]. CNTs are basically
one-dimensional graphene structures rolled into a cylindrical shape. So, their geomet-
ric properties, which is the aspect ratio, can affect the overall properties of CNT-reinforced
polymers. Furthermore, their chirality affects their thermal conductivity. Studies have
shown that the effect of chirality on the conductivity of short-length CNTs is greater than
that of long-length CNTs, and the larger the chiral angle, the greater the conductivity of
CNTs. In addition, zigzag CNTs are less thermally and electrically conductive than arm-
chair CNTs. Therefore, as the tube aspect ratio becomes larger, the conductivity increases
while the effect of chirality on the conductivity decreases [11]. Moreover, another factor
that can contribute to the increment of thermal properties is homogenous dispersion [12].
The way the CNTs are dispersed in the epoxy can significantly affect the properties of the
composites. Loos et al. [13] and Caglayan et al. [14] studied the storage modulus of the
epoxy resin matrix composites reinforced with 0.25 wt.% and 0.75 wt.% CNTs, respectively.
Her and Lin [15] studied the tanδ and loss modulus of epoxy composites reinforced with
0.1 wt.% CNTs. The dispersion method can be improved so as the performance of the
composites.
Heat conduction is based on the principle that the vibration of the atomic lattice
is transmitted to another lattice next to it and vibrates; since CNTs have a regular crys-
talline structure, vibration is not scattered but quickly transmitted from one end to the
other [16]. Long-CNTs can significantly improve thermal conductivity and diffusivity
compared with short ones [17]. It is predicted that the theoretical thermal conductivity of
single-walled carbon nanotubes (SWNTs) can reach more than 6600 W/mK [18]. Experi-
mental measurements on individual multi-walled carbon nanotubes (MWNTs) and SWNTs
have shown high thermal conductivity of over 3000 W/mK [19] and 3500 W/mK [20],
respectively. Wang and Qiu [21] studied the effect of CNTs on the thermal conductivity of
glass fiber/polymer composites. They found that the thermal conductivity of the polymer
reinforced with 3 wt.% of MWNTs was 1.5 times that of the pure glass fiber/polymer
composite. Research has shown that if the amount of CNTs’ weight percentage is more
3. J. Compos. Sci. 2023, 7, 313 3 of 15
than 0.1 wt.%, it cannot significantly increase the thermal conductivity of the composites.
For example, with the addition of 0.1 wt.% and 0.25 wt.% of SWNTs, the storage modulus
of the composite increased by 9% and 16%, respectively [13]. For 0.25 wt.% and 0.75 wt.%
of MWNT-reinforced epoxy composites, the storage modulus of the composites can be
increased by 28% and 35%, respectively [14]. Dispersing CNTs in polymers can slightly
increase the thermal conductivity of nanotube–polymer composites compared to pristine
polymers, while the thermal behavior of CNT composites largely depends on the processing
conditions [15,22–24].
Most of the research has been conducted on aluminum honeycomb sandwich panels.
Therefore, most sandwich panels are metallic at present. The main goal of this study is to
fabricate CNT-reinforced epoxy matrix honeycomb polymer sandwich panels. Honeycomb
sandwich panels made of epoxy polymer and reinforced by CNTs have not been found in
research. There are mainly two types of research on honeycomb-reinforced composites.
One was made of metal honeycombs, and the other was epoxy reinforced with CNTs.
Therefore, this research investigates the thermal properties of CNT-reinforced epoxy honey-
comb sandwich panels, which have not been studied by other researchers. Loos et al. [13]
and Caglayan et al. [14] studied the effect of CNTs on the thermal conductivity of epoxy
matrix composites, Cetin [25] studied the thermal conductivity of MWCNTs reinforced
polyurethane aluminum honeycomb sandwich panels. CNT-reinforced epoxy composite
is suitable for devices increasing thermal conductivity, such as thermal storage devices
and heat exchangers. Moreover, they are suited for high-strength structures needed for
lightweight applications such as aerospace, marine, automotive, and sports [26,27]. More-
over, a new method of dispersing CNTs in epoxy resin was applied, which can significantly
affect the thermal conductivity of the polymer composite. An attempt was made to reinforce
epoxy resins with different weight percentages of CNTs (0.0 wt.%, 0.025 wt.%, 0.050 wt.%,
and 0.075 wt.%) based on the previous research outcomes and the effects of these additives
on the thermal behavior of polymer composites was evaluated.
2. Materials and Methods
To fabricate standard epoxy composites with/without reinforcement, the following
steps were taken.
Standard samples were made of plexiglass and silicone castings.
2.1. Materials
In this work, bisphenol A-based epoxy resin was used. This resin exhibits strong
chemical performance over a broad spectrum of acidic, oxidative alkaline environments,
ambient and higher temperatures [28]. Moreover, cycloaliphatic amin was used as a
hardener in a ratio of 1:4, and the curing time of the resin at room temperature was
measured for 120 min.
A silicone mold was used for epoxy molding. The silicone used was of RTV type. This
material has two components, one of which is resin, and the other is hardener. The mixing
ratio of silicone used in this research is 5 wt.%, which means that the amount of hardener is
equal to 5 wt.% of the resin. After mixing these two components at room temperature for
180 min, the shape changed to become an elastomer (a flexible polymer).
To strengthen the epoxy resin, carboxyl-functionalized MWNTs (diameter: 20–30 nm)
were used as reinforcement materials. Table 1 shows the properties of the CNTs used in
this experiment.
4. J. Compos. Sci. 2023, 7, 313 4 of 15
Table 1. The properties of the used CNTs.
Diameter 20–30 nm
Length 30 µm
Functional Group Carboxyl (COOH)
Purity >95 wt.%
Impurity <1.5 wt.%
2.2. Molding Manufacturing
2.2.1. Making Plexiglass Molds
Plexiglass molds suitable for silicone molding were made. In this way, the shape of
the honeycomb plexiglass mold was first designed by AutoCAD software, and then the
shape was cut on the plexiglass with a laser cutting machine. So, the plexiglass mold was
prepared for silicone loading.
2.2.2. Making Silicone Molds
In order to produce the silicone mold, the wall of the plexiglass mold was first coated
with grease so that the silicone could be separated from the mold after curing. Then, the
silicone resin and the hardener were mixed at a ratio of 5% by weight and mixed thoroughly.
The resulting mixture was poured into the plexiglass mold, and after 3 h, the silicone mold
was completely dry. The reason for using the silicone mold to load epoxy is the flexibility of
silicone; since epoxy is inflexible, a flexible mold should be used so that it can be removed
from the mold after curing, whereas if using a non-flexible mold, such as plexiglass, it is
impossible to separate the epoxy from it.
2.3. Fabrication of Standard Samples
2.3.1. Pure Epoxy Resin
To cast the samples, first, the walls of the rectangular silicone mold with dimensions
30 mm× 10 mm × 2.5 mm were lubricated with grease. Then, the epoxy resin and curing
agent were mixed in a ratio of 1:4 and stirred. The mixture was cast as required and placed
under vacuum at 80 Torr for 60 min. After 120 min, the curing process was completed, and
the pure rectangular epoxy was extracted from the casting mode.
2.3.2. CNT Reinforced Epoxy
The reinforced honeycomb core was made of different weight percentages of CNTs (0.025,
0.05, and 0.075 wt.%) since, according to the research, in the case of higher CNT content,
the CNTs tend to agglomerate and behave like inclusion defects, resulting in a decrease
rather than an increase in properties of the composites. Since the performance of polymer
nanocomposites depends highly on the dispersion of nano-reinforcements in the substrate
and the compatibility of polymer fillers and surface interactions, proper distribution of CNTs
in epoxy resin is essential [29]. Next, the CNT dispersion will be described.
First, weigh a certain amount of epoxy resin (relative to the casting size) and then
weigh the CNTs at 0.025 wt.%, 0.050 wt.%, and 0.075 wt.% of the epoxy weight. Add a
certain amount of acetone into the CNTs and put them into the probe ultrasonic device
(70 W, cycle of 10 s) for 30 min; the device is made by IKA, a company in Staufen, Germany.
This is to eliminate the clot state of the CNTs. Then, add this suspension to the epoxy
resin, and stir the mixture at a temperature of 40 ◦C with a magnetic stirrer for 1 h, thereby
completely extracting acetone. The magnetic hotplate stirrer is made in MTOPS in Seoul,
South Korea. Finally, add the hardener to the homogeneous solution of epoxy resin and
CNTs and stir well [24]. Pour the solution into a pre-lubricated silicone cast and place
the casting in a vacuum at a pressure of 80 Torr for 60 min to extract air bubbles from
the casting. After 120 min, curing will be complete, remove the samples from the casting.
5. J. Compos. Sci. 2023, 7, 313 5 of 15
The vacuum machine is made by KNF, a company in Hamburg, Germany. Figure 1 is a
schematic diagram of the steps for fabricating the reinforced samples.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 5 of 16
casting. The vacuum machine is made by KNF, a company in Hamburg, Germany. Figure
1 is a schematic diagram of the steps for fabricating the reinforced samples.
Figure 1. A schematic of the steps for fabricating the reinforced samples.
The purpose of defoaming is to remove air bubbles in the epoxy/CNT solution. The
vacuum device works by applying opposing pressure to the material and then removing
that pressure. This technique causes air bubbles to move from the solution to the surface,
where they are easily removed from the solution when they reach the surface [30]. Figure
2 shows the CNT-reinforced epoxy matrix honeycomb composite sample.
Figure 2. CNT-reinforced epoxy honeycomb composite sample.
Figure 3 shows the microscopic images of the samples of the pure epoxy resin and
CNT-reinforced epoxy composites, which shows that the CNTs can be well dispersed in
the resin.
(a) (b)
Figure 1. A schematic of the steps for fabricating the reinforced samples.
The purpose of defoaming is to remove air bubbles in the epoxy/CNT solution. The
vacuum device works by applying opposing pressure to the material and then removing
that pressure. This technique causes air bubbles to move from the solution to the surface,
where they are easily removed from the solution when they reach the surface [30]. Figure 2
shows the CNT-reinforced epoxy matrix honeycomb composite sample.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 5 of 16
casting. The vacuum machine is made by KNF, a company in Hamburg, Germany. Figure
1 is a schematic diagram of the steps for fabricating the reinforced samples.
Figure 1. A schematic of the steps for fabricating the reinforced samples.
The purpose of defoaming is to remove air bubbles in the epoxy/CNT solution. The
vacuum device works by applying opposing pressure to the material and then removing
that pressure. This technique causes air bubbles to move from the solution to the surface,
where they are easily removed from the solution when they reach the surface [30]. Figure
2 shows the CNT-reinforced epoxy matrix honeycomb composite sample.
Figure 2. CNT-reinforced epoxy honeycomb composite sample.
Figure 3 shows the microscopic images of the samples of the pure epoxy resin and
CNT-reinforced epoxy composites, which shows that the CNTs can be well dispersed in
the resin.
(a) (b)
Figure 2. CNT-reinforced epoxy honeycomb composite sample.
Figure 3 shows the microscopic images of the samples of the pure epoxy resin and
CNT-reinforced epoxy composites, which shows that the CNTs can be well dispersed in
the resin.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 5 of 16
casting. The vacuum machine is made by KNF, a company in Hamburg, Germany. Figure
1 is a schematic diagram of the steps for fabricating the reinforced samples.
Figure 1. A schematic of the steps for fabricating the reinforced samples.
The purpose of defoaming is to remove air bubbles in the epoxy/CNT solution. The
vacuum device works by applying opposing pressure to the material and then removing
that pressure. This technique causes air bubbles to move from the solution to the surface,
where they are easily removed from the solution when they reach the surface [30]. Figure
2 shows the CNT-reinforced epoxy matrix honeycomb composite sample.
Figure 2. CNT-reinforced epoxy honeycomb composite sample.
Figure 3 shows the microscopic images of the samples of the pure epoxy resin and
CNT-reinforced epoxy composites, which shows that the CNTs can be well dispersed in
the resin.
(a) (b)
Figure 3. Microscopic images of (a) pure epoxy, (b) CNT-reinforced epoxy composites (CNTs have
been circled out).
6. J. Compos. Sci. 2023, 7, 313 6 of 15
2.4. Dynamic Mechanical Thermal Analysis (DMTA)
DMTA analysis is one of the thermal analysis methods widely used to study and
identify polymers. This analysis was performed to study the viscoelasticity of epoxy
resins in their pure state and reinforced with CNTs [31]. Mechanical changes in polymer
sample behavior were measured in terms of temperature, time, frequency, stress, and strain.
Samples were analyzed by a DMTA-Triton device, Triton, model 2000 and made in the UK.
DMTA analysis was performed on a rectangular sample with a length of 30 mm, a width of
10 mm and a thickness of 2.5 mm, a frequency of 1 Hz, a temperature range of 20 to 200 ◦C,
a heating rate of 5 ◦C/min and in bending mode. In this work, the storage modulus, loss
modulus, and tanδ were investigated.
2.5. Thermogravimetric Analysis (TGA)
TGA was used to study the thermal properties of epoxy resins and to investigate the
effect of the addition of CNTs on these properties. This analysis is widely used to study the
thermal stability of the polymer as a function of temperature [32]. The role of temperature in
evaluating the degradability of epoxy resins was studied by TGA. In this test, the weight of
the testing material was continuously measured and recorded as the temperature increased.
Based on this analysis, the degradability rate of epoxy resin and epoxy reinforced with
different percentages of CNTs can be obtained. The tests were performed on 6 mg samples
with an SDT Q600 V20.9 Build 20 device made by TA Instruments, a company based in the
USA, at a heating rate of 10 ◦C/min and under N2 atmosphere in the temperature range of
25 to 600 ◦C.
3. Results and Discussion
3.1. Dynamic Mechanical Thermal Analysis (DMTA)
The storage modulus (E0) and loss modulus (E00) in viscoelastic materials measure
the energy stored (representing the elastic part) and the energy dissipated as heat (repre-
senting the viscous part), respectively. The tensile storage and loss moduli are defined as
follows [33]:
Storage : E0
=
σ0
ε0
cos δ (1)
Loss : E00
=
σ0
ε0
sin δ (2)
where δ is the phase lag between stress and strain. Stress and strain in a viscoelastic material
can be expressed by the following expressions [33]:
Stress : σ = σ0sin(ωt + δ) (3)
Strain : ε = ε0sin(ωt) (4)
where t is the time, ωt is the phase angle change, ε0 and σ0 are the initial (t = 0) strain and
stress, respectively.
The ratio of the loss modulus to the storage modulus for a viscoelastic material used
in tensile testing is defined as [33]
tan δ =
E00
E0
(5)
It is often called damping, and it is a measure of the energy dissipation of a material.
Damping is the dissipation of energy in a material under cyclic load. It measures how well a
material sheds energy and is reported as the tangent of the phase angle. It tells us how well
a material absorbs energy. For materials with tanδ greater than 1, the energy-dissipative
viscous component of the modulus dominates [34].
The storage modulus plot of the pure and nanocomposite samples is shown in Figure 4.
The storage modulus values of all nano-composite samples are higher than that of the
7. J. Compos. Sci. 2023, 7, 313 7 of 15
pure resin samples. The E0 values increase with the addition of CNTs, which is due to the
limitation of the polymer chain movement only by the addition of CNTs [35]. Thus, the
epoxy was hardened below the Tg (glass transition temperature) point, and as a result, the
range of the storage modulus increased. Due to the flexibility of the polymer chains, the
value dropped significantly after the Tg point. The highest storage modulus values were
obtained for the samples reinforced with 0.075 wt.% CNTs due to the presence of a strong
interface, which effectively transmits force between the epoxy and the CNTs. This result
indicates that these nanocomposite samples have the best elastic portion energy absorption
behavior. In addition, the Tg firstly slightly increases from around 65–70 ◦C for the pure
epoxy sample to around 70 ◦C for the nanocomposite sample reinforced with 0.025 wt.%
CNTs, then the Tg dramatically decreases to around 42–45 ◦C for the nanocomposite
sample reinforced by 0.05 wt.% CNTs. Thereafter, the Tg stays stable around 40–43 ◦C
for the nanocomposite sample reinforced with 0.075 wt.% CNTs, indicating a threshold
existing for the optimal effect of the CNT content on the material behavior.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 7 of 16
well a material absorbs energy. For materials with tanδ greater than 1, the energy-dissipa-
tive viscous component of the modulus dominates [34].
The storage modulus plot of the pure and nanocomposite samples is shown in Figure
4. The storage modulus values of all nano-composite samples are higher than that of the
pure resin samples. The E’ values increase with the addition of CNTs, which is due to the
limitation of the polymer chain movement only by the addition of CNTs [35]. Thus, the
epoxy was hardened below the Tg (glass transition temperature) point, and as a result, the
range of the storage modulus increased. Due to the flexibility of the polymer chains, the
value dropped significantly after the Tg point. The highest storage modulus values were
obtained for the samples reinforced with 0.075 wt.% CNTs due to the presence of a strong
interface, which effectively transmits force between the epoxy and the CNTs. This result
indicates that these nanocomposite samples have the best elastic portion energy absorp-
tion behavior. In addition, the Tg firstly slightly increases from around 65–70 °C for the
pure epoxy sample to around 70 °C for the nanocomposite sample reinforced with 0.025
wt.% CNTs, then the Tg dramatically decreases to around 42–45 °C for the nanocomposite
sample reinforced by 0.05 wt.% CNTs. Thereafter, the Tg stays stable around 40–43 °C for
the nanocomposite sample reinforced with 0.075 wt.% CNTs, indicating a threshold exist-
ing for the optimal effect of the CNT content on the material behavior.
Figure 4. Storage modulus vs. temperatures for pure resin and nanocomposite samples.
According to Figure 5, the maximum storage modulus of the epoxy sample rein-
forced with 0.075 wt.% CNTs increased by 43.8% compared to pure epoxy resin samples.
The storage modulus of the samples reinforced with 0.025 and 0.05 wt.% of CNTs in-
creased by 26.8% and 34.9%, respectively.
Figure 4. Storage modulus vs. temperatures for pure resin and nanocomposite samples.
According to Figure 5, the maximum storage modulus of the epoxy sample reinforced
with 0.075 wt.% CNTs increased by 43.8% compared to pure epoxy resin samples. The
storage modulus of the samples reinforced with 0.025 and 0.05 wt.% of CNTs increased by
26.8% and 34.9%, respectively.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 8 of 16
Figure 5. Comparison of the storage modulus of samples vs. CNT wt.%.
As shown in Figure 6, the loss modulus (E’’) of the nano-composite samples increased
compared to the pure resin samples. The loss modulus also follows the same trend as that
observed in the storage modulus, which indicates a greater amount of energy loss in the
nanocomposite samples compared to the pure epoxy sample. However, the temperatures
corresponding to the maximum loss modulus dramatically increase from 41.4 °C to 64.7
Figure 5. Comparison of the storage modulus of samples vs. CNT wt.%.
8. J. Compos. Sci. 2023, 7, 313 8 of 15
As shown in Figure 6, the loss modulus (E00) of the nano-composite samples increased
compared to the pure resin samples. The loss modulus also follows the same trend as that
observed in the storage modulus, which indicates a greater amount of energy loss in the
nanocomposite samples compared to the pure epoxy sample. However, the temperatures
corresponding to the maximum loss modulus dramatically increase from 41.4 ◦C to 64.7 ◦C
with CNT contents increase from 0 wt.% to 0.025 wt.%, then slightly increase from 64.7 ◦C to
70.6 ◦C with CNT contents increase from 0.025 wt.% to 0.050 wt.%. Finally, the temperatures
start dramatically decreasing from 70.6 ◦C to 43.2 ◦C. This phenomenon reflects again the
effect of the CNT content on the material behavior and indicates a threshold existing for
the CNT content to achieve the optimal effect.
Figure 5. Comparison of the storage modulus of samples vs. CNT wt.%.
As shown in Figure 6, the loss modulus (E’’) of the nano-composite samples increased
compared to the pure resin samples. The loss modulus also follows the same trend as that
observed in the storage modulus, which indicates a greater amount of energy loss in the
nanocomposite samples compared to the pure epoxy sample. However, the temperatures
corresponding to the maximum loss modulus dramatically increase from 41.4 °C to 64.7
°C with CNT contents increase from 0 wt.% to 0.025 wt.%, then slightly increase from 64.7
°C to 70.6 °C with CNT contents increase from 0.025 wt.% to 0.050 wt.%. Finally, the tem-
peratures start dramatically decreasing from 70.6 °C to 43.2 °C. This phenomenon reflects
again the effect of the CNT content on the material behavior and indicates a threshold
existing for the CNT content to achieve the optimal effect.
According to Figure 7, the loss modulus of the nano-composite sample reinforced
with 0.075 wt.% CNTs increased by 74.4% compared to pure epoxy resin. Furthermore,
the loss moduli of the samples reinforced with 0.025 and 0.05 wt.% CNTs increased by
48.8% and 67.0%, respectively, compared to the pure epoxy samples.
Figure 6. Loss modulus vs. temperatures for pure and nanocomposite samples.
Figure 6. Loss modulus vs. temperatures for pure and nanocomposite samples.
According to Figure 7, the loss modulus of the nano-composite sample reinforced with
0.075 wt.% CNTs increased by 74.4% compared to pure epoxy resin. Furthermore, the loss
moduli of the samples reinforced with 0.025 and 0.05 wt.% CNTs increased by 48.8% and
67.0%, respectively, compared to the pure epoxy samples.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 9 of 16
Figure 7. Comparison of the loss modulus of samples with different wt.% of CNTs.
Figure 8 shows the tanδ for the pure epoxy and nano-composite samples vs. temper-
ature. As wt.% CNTs increases, the tanδ increases. The tanδ also follows the trend of the
results observed in the storage and loss moduli, which indicates larger tanδ values for the
nanocomposite samples compared to the pure samples. The tanδ values of the nanocom-
Figure 7. Comparison of the loss modulus of samples with different wt.% of CNTs.
9. J. Compos. Sci. 2023, 7, 313 9 of 15
Figure 8 shows the tanδ for the pure epoxy and nano-composite samples vs. tem-
perature. As wt.% CNTs increases, the tanδ increases. The tanδ also follows the trend of
the results observed in the storage and loss moduli, which indicates larger tanδ values
for the nanocomposite samples compared to the pure samples. The tanδ values of the
nanocomposite samples are all greater than one, indicating that the energy-dissipative
viscous components of the modulus of these samples dominate, especially for the nanocom-
posite sample with 0.075 wt.% CNTs, the tanδ reaches 5.138. In addition, the temperatures
corresponding to the maximum tanδ change with the CNT content in a similar pattern as
the above material behavior.
Figure 7. Comparison of the loss modulus of samples with different wt.% of CNTs.
Figure 8 shows the tanδ for the pure epoxy and nano-composite samples vs. temper-
ature. As wt.% CNTs increases, the tanδ increases. The tanδ also follows the trend of the
results observed in the storage and loss moduli, which indicates larger tanδ values for the
nanocomposite samples compared to the pure samples. The tanδ values of the nanocom-
posite samples are all greater than one, indicating that the energy-dissipative viscous com-
ponents of the modulus of these samples dominate, especially for the nanocomposite sam-
ple with 0.075 wt.% CNTs, the tanδ reaches 5.138. In addition, the temperatures corre-
sponding to the maximum tanδ change with the CNT content in a similar pattern as the
above material behavior.
Figure 8. The effect of CNTs on tanδ of pure epoxy resin and nano-composite samples.
According to Figure 9, the maximum tanδ of the nano-composite sample reinforced
with 0.075 wt.% CNTs increased by 696% compared to pure epoxy resin. Furthermore, the
Figure 8. The effect of CNTs on tanδ of pure epoxy resin and nano-composite samples.
According to Figure 9, the maximum tanδ of the nano-composite sample reinforced
with 0.075 wt.% CNTs increased by 696% compared to pure epoxy resin. Furthermore, the
loss moduli of the samples reinforced with 0.025% and 0.05 wt.% CNTs increase by 74.9%
and 99.5%, respectively, compared to the pure epoxy samples. An increase in tanδ indicates
a higher ability of the material to dissipate energy. Since CNTs have the properties of energy
absorption and folding due to the π-bond in their structure, by adding CNTs to the polymer
matrix, the ability of the material to absorb energy increases, so tanδ increases [36].
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 10 of 16
loss moduli of the samples reinforced with 0.025% and 0.05 wt.% CNTs increase by 74.9%
and 99.5%, respectively, compared to the pure epoxy samples. An increase in tanδ indi-
cates a higher ability of the material to dissipate energy. Since CNTs have the properties
of energy absorption and folding due to the π-bond in their structure, by adding CNTs to
the polymer matrix, the ability of the material to absorb energy increases, so tanδ increases
[36].
Figure 9. Comparison of tanδ of samples with different wt.% CNTs.
The above results are consistent with the research of Her and Lin [32]. They studied
the mechanical dynamic properties by adding SWNTs to the epoxy resin and observed
that by adding 1 wt.% CNT reinforcement to the epoxy, the storage modulus increased by
52%, and the loss modulus increased by 45% compared to the pure epoxy resin. Further-
more, research shows that adding 0.1 wt.% CNTs, the tanδ and the loss modulus of its
epoxy samples were increased by 42% and 36%, respectively, compared to the pure epoxy
Figure 9. Comparison of tanδ of samples with different wt.% CNTs.
The above results are consistent with the research of Her and Lin [32]. They studied the
mechanical dynamic properties by adding SWNTs to the epoxy resin and observed that by
10. J. Compos. Sci. 2023, 7, 313 10 of 15
adding 1 wt.% CNT reinforcement to the epoxy, the storage modulus increased by 52%, and
the loss modulus increased by 45% compared to the pure epoxy resin. Furthermore, research
shows that adding 0.1 wt.% CNTs, the tanδ and the loss modulus of its epoxy samples were
increased by 42% and 36%, respectively, compared to the pure epoxy resin [13].
3.2. Thermal Gravimetric Analysis (TGA)
TGA analysis was used to evaluate the effect of adding CNTs on the thermal stability of
epoxy resin. Figure 10 shows the TGA plots of the pure epoxy resin and its nanocomposites
reinforced with different wt.% CNTs. Moreover, Figure 11 shows a type of thermal analysis
in which the rate of material weight changes upon heating is plotted against temperature
(DTGA) for the same samples. From the figures above, the degradation temperature of
the pure sample and the nanocomposite samples containing 0.025, 0.05, and 0.075 wt.%
CNTs are different so that the degradation of the nanocomposite samples occurs at a higher
temperature. In other words, by adding CNTs, we can conclude that the thermal stability
of the nanocomposite samples is increased. The reason for this can be attributed to the
very good thermal stability of CNTs. CNTs are excellent thermal conductors that allow
applied heat to transfer through themselves so that the heat is not concentrated in one
place, delaying degradation [37].
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 11 of 16
Figure 10. Comparison of TGA results of pure epoxy and nanocomposites containing different wt.%
CNTs.
Figure 11. DTGA diagram of pure epoxy and nanocomposites containing different amounts of
weight percentage of carbon nanotubes.
Table 2 shows the maximum weight loss temperature Tmax values, which is defined as
the maximum temperature of epoxy decomposition. With the addition of CNTs, the max-
imum weight loss temperatures increase due to the strong interactions between the CNTs
and the epoxy matrix. At the same time, the CNTs act as physical crosslinks and reduce
the fluidity of the polymer matrix; hence, the glass transition temperature increases [38].
Figure 10. Comparison of TGA results of pure epoxy and nanocomposites containing different wt.% CNTs.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 11 of 16
Figure 10. Comparison of TGA results of pure epoxy and nanocomposites containing different wt.%
CNTs.
Figure 11. DTGA diagram of pure epoxy and nanocomposites containing different amounts of
weight percentage of carbon nanotubes.
Table 2 shows the maximum weight loss temperature Tmax values, which is defined as
the maximum temperature of epoxy decomposition. With the addition of CNTs, the max-
imum weight loss temperatures increase due to the strong interactions between the CNTs
and the epoxy matrix. At the same time, the CNTs act as physical crosslinks and reduce
the fluidity of the polymer matrix; hence, the glass transition temperature increases [38].
Figure 11. DTGA diagram of pure epoxy and nanocomposites containing different amounts of weight
percentage of carbon nanotubes.
Table 2 shows the maximum weight loss temperature Tmax values, which is defined as
the maximum temperature of epoxy decomposition. With the addition of CNTs, the maxi-
11. J. Compos. Sci. 2023, 7, 313 11 of 15
mum weight loss temperatures increase due to the strong interactions between the CNTs
and the epoxy matrix. At the same time, the CNTs act as physical crosslinks and reduce the
fluidity of the polymer matrix; hence, the glass transition temperature increases [38].
Table 2. The maximum weight loss temperatures of nanocomposite samples, corresponding to the
pure epoxy sample, containing different wt.% CNTs.
Sample Tmax (◦C)
Pure Epoxy 355
Epoxy + 0.025% CNT 362
Epoxy + 0.05% CNT 363
Epoxy + 0.075% CNT 364
As can be seen from Table 3, the weight loss temperature of the nanocomposite samples
containing 0.025, 0.05, and 0.075 wt.% CNTs equivalent to 10% weight loss of the epoxy
sample increased by 11.4, 12.6, and 14.0 ◦C, respectively, compared to the pure epoxy
sample. In addition, the epoxy samples containing 0.025, 0.05, and 0.075 wt.% CNTs
corresponded to 50% weight loss of the epoxy sample, and the weight loss temperatures
increased by 0.20, 3.8, and 4.3 ◦C, respectively, compared to the pure epoxy sample. The
reason for this can be attributed to the very good thermal stability of CNTs and the surface
interactions between CNTs and epoxy [39].
Table 3. Degradation temperatures of nanocomposite samples, corresponding to 10% and 50% weight
loss for epoxy samples containing different wt.% CNTs.
Sample T10 (◦C) T50 (◦C)
Pure Epoxy 8.333 372.3
Epoxy + 0.025% CNT 2.345 372.5
Epoxy + 0.05% CNT 4.346 376.1
Epoxy + 0.075% CNT 8.347 376.6
A study on pure epoxy resin and CNT-reinforced epoxy matrix composites showed
that by adding 1, 2, and 3 wt.% CNTs, the 5% mass loss temperatures of these materials
were 351, 356, and 358 ◦C, respectively, which is comparable with this work on a similar
model [40].
According to Figure 12, the thermal stability of the nano-composite samples reinforced
with 0.025, 0.05, and 0.075 wt.% CNTs, compared to the pure epoxy sample at 10% weight
loss of the sample, which increased by 3.4%, 3.7%, and 4.2%, respectively. In addition,
compared to the pure epoxy sample at 50% weight loss of the epoxy sample, the ther-
mal stability increasements of 0.04%, 1% and 1.1% were observed for the nanocomposite
samples reinforced by 0.025, 0.05, and 0.075 wt.%, respectively.
Similar behavior to that reported by Loos [13] can be found in this work. His TGA
analysis on reinforced epoxy composites with 0.1 wt.% and 0.25 wt.% CNTs showed that
all samples began to lose weight around 70 ◦C, degraded by 90% around 550 ◦C, and
the second weight loss occurred between 190–320 ◦C (peak at 250 ◦C), probably due to
decomposition of lower molecular weight materials, and a third between 290–490 ◦C (peak
at 370 ◦C).
12. J. Compos. Sci. 2023, 7, 313 12 of 15
model [40].
According to Figure 12, the thermal stability of the nano-composite samples rein-
forced with 0.025, 0.05, and 0.075 wt.% CNTs, compared to the pure epoxy sample at 10%
weight loss of the sample, which increased by 3.4%, 3.7%, and 4.2%, respectively. In addi-
tion, compared to the pure epoxy sample at 50% weight loss of the epoxy sample, the
thermal stability increasements of 0.04%, 1% and 1.1% were observed for the nanocompo-
site samples reinforced by 0.025, 0.05, and 0.075 wt.%, respectively.
Figure 12. The percentage increase in thermal stability of the sandwich panels at 10% and 50%
weight loss of the epoxy-containing different wt.% CNTs, compared to the pure epoxy sample.
Similar behavior to that reported by Loos [13] can be found in this work. His TGA
analysis on reinforced epoxy composites with 0.1 wt.% and 0.25 wt.% CNTs showed that
all samples began to lose weight around 70 °C, degraded by 90% around 550 °C, and the
second weight loss occurred between 190–320 °C (peak at 250 °C), probably due to decom-
position of lower molecular weight materials, and a third between 290–490 °C (peak at 370
°C).
3.3. Density
Density measurements were performed to evaluate the effect of adding CNT rein-
forcement on the density of the epoxy resin. It was observed that the density increased
Figure 12. The percentage increase in thermal stability of the sandwich panels at 10% and 50% weight
loss of the epoxy-containing different wt.% CNTs, compared to the pure epoxy sample.
3.3. Density
Density measurements were performed to evaluate the effect of adding CNT rein-
forcement on the density of the epoxy resin. It was observed that the density increased
with the wt.% CNTs. According to Figure 13, the actual density of samples reinforced with
0.075 wt.% CNTs increased by 0.43% compared to the pure epoxy resin. Furthermore, the
density of the samples reinforced with 0.025 and 0.05 wt.% CNTs increased by 0.172% and
0.35%, respectively, compared to the pure epoxy sample.
J. Compos. Sci. 2023, 7, x FOR PEER REVIEW 13 o
with the wt.% CNTs. According to Figure 13, the actual density of samples reinforced w
0.075 wt.% CNTs increased by 0.43% compared to the pure epoxy resin. Furthermore,
density of the samples reinforced with 0.025 and 0.05 wt.% CNTs increased by 0.172% a
0.35%, respectively, compared to the pure epoxy sample.
In order to calculate the ratio of the actual density to the theoretical density of
materials, the theoretical densities of the CNT-reinforced epoxy matrix composites w
different weight percentages of CNTs need to be calculated. Therefore, according to
law of mixtures as in Equation (6), the theoretical densities of the pure epoxy and na
composite samples reinforced with different wt.% CNTs, assuming that the theoret
density of the epoxy sample is 1.25 g/cm3 and the theoretical density of CNTs is 1.6 g/c
the theoretical densities of the nanocomposite samples reinforced by 0.025, 0.05, and 0.
wt.% CNTs are calculated to be 1.2500, 1.2501, 1.2502, and 1.2503 g/cm3, respectively [
𝜌 = 𝜌 𝑉 + 𝜌 𝑉
where ρe and ρn denote the density of the epoxy and CNTs, respectively, and Ve and Vn
the weight percent of the epoxy and CNTs, respectively. The ratio of the actual densit
the theoretical density for the pure epoxy and nanocomposite samples reinforced w
0.025, 0.05, and 0.075 wt.% CNTs are 0.9240, 0.9255, 0.9270, and 0.9278, respectively.
Figure 13. Effect of adding CNTs on the density of pure epoxy and nanocomposite samples r
forced with different wt.% CNTs.
Ciecierska et al. [40] showed that the densities of the pure epoxy and CNT-reinfor
epoxy matrix composites with 0.1, 1.0 and 2.0 wt.% of CNTs were 1.1972, 1.1994, 1.19
and 1.1997 g/cm3, respectively. The reason is that after the addition of CNTs in epoxy re
the free movement of polymer chains is restricted because the free volume between m
romolecules is occupied by CNTs; thus, the chains are more squeezed, and the crossl
density increases [40].
4. Conclusions
• DMTA showed that the storage modulus, loss modulus, and tanδ values increa
Figure 13. Effect of adding CNTs on the density of pure epoxy and nanocomposite samples reinforced
with different wt.% CNTs.
In order to calculate the ratio of the actual density to the theoretical density of the
materials, the theoretical densities of the CNT-reinforced epoxy matrix composites with
different weight percentages of CNTs need to be calculated. Therefore, according to the law
of mixtures as in Equation (6), the theoretical densities of the pure epoxy and nanocomposite
samples reinforced with different wt.% CNTs, assuming that the theoretical density of the
epoxy sample is 1.25 g/cm3 and the theoretical density of CNTs is 1.6 g/cm3, the theoretical
13. J. Compos. Sci. 2023, 7, 313 13 of 15
densities of the nanocomposite samples reinforced by 0.025, 0.05, and 0.075 wt.% CNTs are
calculated to be 1.2500, 1.2501, 1.2502, and 1.2503 g/cm3, respectively [41].
ρ = ρeVe + ρnVn (6)
where ρe and ρn denote the density of the epoxy and CNTs, respectively, and Ve and Vn
are the weight percent of the epoxy and CNTs, respectively. The ratio of the actual density
to the theoretical density for the pure epoxy and nanocomposite samples reinforced with
0.025, 0.05, and 0.075 wt.% CNTs are 0.9240, 0.9255, 0.9270, and 0.9278, respectively.
Ciecierska et al. [40] showed that the densities of the pure epoxy and CNT-reinforced
epoxy matrix composites with 0.1, 1.0 and 2.0 wt.% of CNTs were 1.1972, 1.1994, 1.1996,
and 1.1997 g/cm3, respectively. The reason is that after the addition of CNTs in epoxy
resin, the free movement of polymer chains is restricted because the free volume between
macromolecules is occupied by CNTs; thus, the chains are more squeezed, and the crosslink
density increases [40].
4. Conclusions
• DMTA showed that the storage modulus, loss modulus, and tanδ values increased
with the increase of wt.% CNTs. The storage modulus, the loss modulus, and the tanδ
of the nanocomposite sample reinforced with 0.075 wt.% CNTs increased by 43.8%,
74.4%, and 696%, respectively, compared to the pure epoxy resin. The reason why the
three parameters of dissipation modulus, storage modulus and tanδ all increase with
the increase of the wt.% CNTs is the energy absorption property of the CNTs.
• TGA showed that the epoxy nanocomposites were thermally stable due to the addition
of CNTs. The increase in the degradation temperature of the nanocomposites is due
to the strong interactions between the epoxy matrix and the CNTs, which is caused
by the thermal stability of the CNTs. The pure epoxy sample has the lowest degra-
dation temperature. By adding 0.075 wt.% CNTs to the epoxy resin, the temperature
corresponding to a 10% and 50% weight loss in the pure epoxy samples increased by
14 ◦C and 4.3 ◦C, respectively. According to the results of the DTGA, the degradation
temperature of the nanocomposite samples reinforced with 0.075 wt.% CNTs increased
by 9 ◦C.
• Density measurements showed that the density of the nanocomposite samples in-
creased by adding CNTs to the pure epoxy resin. The ratio of the actual density to
the theoretical density of the nanocomposite samples reinforced with 0.025, 0.05, and
0.075 wt.% CNTs are 0.925, 0.926 and 0.927, respectively.
• The well-dispersed CNTs in the epoxy resin can strongly affect the performance of the
composites. Otherwise, the CNTs cannot significantly improve the performance of
the resin.
• Since CNT-reinforced epoxy matrix composites can absorb more energy through
heat and can be used to reduce heat loss and resist high temperatures, which is an
optimal choice for designers and engineers who want to increase the effectiveness of
their products.
Author Contributions: Conceptualization, L.N.; methodology, L.N.; formal analysis, L.N. and Z.H.;
investigation, L.N. and Z.H.; resources, L.N.; data curation, L.N.; writing—original draft preparation,
L.N.; writing—review and editing, Z.H.; visualization, L.N. and Z.H.; supervision, Z.H. All authors
have read and agreed to the published version of the manuscript.
Funding: This research received no external funding.
Data Availability Statement: Not applicable.
Acknowledgments: This work was supported by the J. J. Lohr College of Engineering and the Me-
chanical Engineering Department at South Dakota State University and are gratefully acknowledged.
14. J. Compos. Sci. 2023, 7, 313 14 of 15
Conflicts of Interest: The authors declare no conflict of interest. The funders had no role in the design
of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript; or
in the decision to publish the results.
References
1. Silvia, R.; Antonio, N. Mechanical Characterization of Sandwich Structure Comprised of Glass Fiber Reinforced Core. In
Proceedings of the Composites in Construction part 2, in 3rd International Conference—Composites in Construction 2005, Iyon,
France, 11–13 July 2005.
2. Jorio, D.G.; Dresselhaus, M.S.; Jorio, A. Carbon nanotubes advanced topics in the synthesis. In Structure, Properties and Applications;
Springer: New York, NY, USA, 2008.
3. Berber, S.; Kwon, Y.; Tomanek, D. Unusually high thermal conductivity of carbon nanotubes. Phsical. Rev. Lett. 2000, 84, 4613–4616.
[CrossRef] [PubMed]
4. Najmi, L.; Zebarjad, S.M.; Janghorban, K. Effects of Carbon Nanotubes on the Compressive and Flexural Strength and Microscopic
Structure of Epoxy Honeycomb Sandwich Panels. Polym. Sci. Ser. B 2023, 65, 220–229. [CrossRef]
5. Fatemi, J.; Lemmen, M.H.J. Effective Thermal/Mechanical Properties of Honeycomb Core Panels for Hot Structure Applications.
J. Spacecr. Rocket. 2009, 46, 514–525. [CrossRef]
6. Tahmasbi, V.; Noori, S. Thermal Analysis of Honeycomb Sandwich Panels as Substrate of Ablative Heat Shield. J. Thermophys.
Heat Transf. 2017, 32, 1–12. [CrossRef]
7. Kim, P.; Shi, L.; Majumdar, A.; McEuen, P.L. Thermal transport measurements of individual multiwalled nanotubes. Phys. Rev.
Lett. 2001, 87, 215502. [CrossRef]
8. Pop, E.; Mann, D.; Wang, Q.; Goodson, K.; Dai, H. Thermal conductance of an individual single-wall carbon nanotube above
room temperature. Nano Lett. 2006, 6, 96–100. [CrossRef]
9. Wang, S.; Qiu, J. Enhancing thermal conductivity of glass fiber/polymer composites through carbon nanotubes incorporation.
Compos. Part B Eng. 2010, 41, 533–536. [CrossRef]
10. Hashemi, S.A.; Mousavi, S.M. Effect of bubble based degradation on the physical properties of single wall carbon nanotube/epoxy
resin composite and new approach in bubbles reduction. Compos. Part A Appl. Sci. Manuf. 2016, 90, 457–469. [CrossRef]
11. Najmi, L.; Hu, Z. Review on Molecular Dynamics Simulations of Effects of Carbon Nanotubes (CNTs) on Electrical and Thermal
Conductivities of CNT-Modified Polymeric Composites. J. Compos. Sci. 2023, 7, 165. [CrossRef]
12. Kim, J.B.; Byun, J.H. Influence of the CNT length on complex permittivity of composite laminates and on radar absorber design
in X-band. In Proceedings of the 10th IEEE International Conference on Nanotechnology, Ilsan, Korea, 17–20 August 2010; pp.
635–638.
13. Loos, M.R.; CoelhoI, L.A.; Pezzini, S.H. Effect of carbon nanotubes addition on the mechanical and thermal properties of epoxy
matrices. Mater. Res. 2008, 11, 347. [CrossRef]
14. Caglayan, C.; Kim, G.; Yun, G.J. CNT-Reinforced Self-Healable Epoxy Dynamic Networks Based on Disulfide Bond Exchange.
ACS Omega 2022, 7, 43480–43491. [CrossRef] [PubMed]
15. Her, S.C.; Lin, K.Y. Dynamic mechanical analysis of carbon nanotube-reinforced nanocomposites. J. Appl. Biomater. Funct. Mater.
2017, 15, 13–18. [CrossRef] [PubMed]
16. Burger, N.; Laachachi, A.; Ferriol, M.; Lutz, M.; Toniazzo, V. Review of thermal conductivity in composites: Mechanisms,
parameters and theory. Prog. Polym. Sci. 2016, 61, 1–28. [CrossRef]
17. Lee, D.K.; Yoo, J.; Kim, H.; Kang, B.H.; Park, S.H. Electrical and Thermal Properties of Carbon Nanotube Polymer Composites
with Various Aspect Ratios. Materials 2022, 15, 1356. [PubMed]
18. Karingamanna, J.; Nanoth, R.; Kumar, M.R. Thermal and Rheological Measurement Techniques for Nanomaterials Characteriza-
tion. In Micro and Nano Technologies; Elsevier: Amsterdam, The Netherlands, 2017.
19. Bhagyaraj, S.; Oluwafemi, O.S.; Kalarikkal, N.; Thomas, S. Characterization of Nanomaterials; Elsevier: Amsterdam, The Netherlands, 2018.
20. Anirudh, S.; Caroline, P.; Mattiasson, B.J. Probing the eelationship between molecular structures, thermal transitions and
morphology in polymer semiconductors using a woven glass-mesh based DMTA technique. Chem. Mater. 2019, 31, 6740–6749.
21. Danoglidis, P.A.; Konsta-Gdoutos, M.S.; Gdoutos, E.E.; Shah, S.P. Strength, energy absorption capability and self-sensing
properties of multifunctional carbon nanotube reinforced mortars. Constr. Build. Mater. 2016, 120, 265–274. [CrossRef]
22. Saito, R.; Dresselhaus, G.; Dresselhaus, M.S. Physical Properties of Carbon Nanotubes; Imperial College Press: Tokyo, Japan, 1998.
23. Chalal, S.; Haddadine, N.; Bouslah, N.; Souilah, S.; Benaboura, A.; Barille, R.; Haroun, A. Preparation characterization and
thermal behaviour of carbopol-TiO2 nanocomposites. Open J. Org. Polym. Mater. 2014, 4, 55–64. [CrossRef]
24. Xu, F.; Sun, L.; Zhang, J.; Qi, Y.; Yang, L.; Ru, H.; Wang, C.; Meng, X.; Lan, X.; Jiao, Q.; et al. Thermal stability of carbon nanotubes.
J. Therm. Anal. Calorim. 2010, 102, 785–791.
25. Han, Z.H.; Fina, A. Thermal conductivity of carbon nanotubes and their polymer nanocomposites. Prog. Polym. Sci. 2011, 36,
914–944.
26. Cetin, M.E. Improvement of the structural, thermal, and mechanical properties of polyurethane adhesives with nanoparticles and
their application to Al/Al honeycomb sandwich panels. Mater. Test. 2022, 64, 272–283. [CrossRef]
27. Nejad, S.M.; Srivastava, R.; Bellussi, F.M.; Thielemann, H.N.C.; Fasano, P.A.M. Nanoscale thermal properties of carbon nan-
otubes/epoxy composites by atomistic simulations. Int. J. Therm. Sci. 2021, 159, 106588. [CrossRef]
15. J. Compos. Sci. 2023, 7, 313 15 of 15
28. Bajpai, R.; Davidson, J.R.; Robert, C. Studies on the Modification of Commercial Bisphenol-A-Based Epoxy Resin Using Different
Multifunctional Epoxy Systems. Appl. Mech. 2021, 2, 419–430. [CrossRef]
29. Omidi, M.J.; Shayan Mehr, M. Improving the dispersion of SWNT in epoxy resin through a simple Multi-Stage method. J. King
Saud Univ. 2019, 31, 202–208. [CrossRef]
30. Sharma, S.C. Equation for the density of particle-reinforced metal matrix composites: A new approach. J. Mater. Eng. Perform.
2003, 12, 324–330. [CrossRef]
31. Tuwair, H.; Hopkins, M.; Volz, J.; ElGawady, M.A.; Mohamed, M.; Chandrashekhara, K.; Birman, V. Evaluation of sandwich
panels with various polyurethane foam-cores and ribs. Compos. Part B Eng. 2015, 79, 256–276. [CrossRef]
32. Allen, H.G. Analysis and Design of Structural Sandwich Panels; Oxford: New York, NY, USA, 1969.
33. Murata, H. Theory and Application to Biomaterials. In Polymerization; InTech: Nagasaki, Japan, 2012.
34. Sperling, L.H. Sound and Vibration Damping with Polymers. In Basic Viscoelastic Definitions and Concepts; American Chemical
Society: Washington, DC, USA, 1990.
35. Leite, M.; Silva, A.; Freitas, M. Elastic behaviour of sandwich beams part 2: Numerical study. In Proceedings of the 9th Portuguese
Conference on Fracture, Setubal, Portugal, 18–20 February 2004.
36. Zebarjad, S.M.; Moghim, M.H. An Introduction to Polymer Nanocomposites; Mashhad: Ferdowsi, Iran, 2015.
37. Ji, L.; Stevens, M.M.; Zhu, Y.; Gong, Q.; Wu, J.; Liang, J. Preparation and properties of multi-walled carbon nan-
otube/carbon/polystyrene composites. Carbon 2009, 47, 2733–2741. [CrossRef]
38. Biercuk, M.J.; Llaguno, M.C.; Radosavijevic, M.; Hyun, J.K.; Johnson, A.T.; Fischer, J.E. Carbon nanotube composites for thermal
management. Appl. Phys. Lett. 2002, 80, 2767–2769.
39. Du, F.; Guthy, C.; Kashiwagi, T.; Fischer, J.E. An infiltration method for preparing single-wall nanotube/epoxy composites with
improved thermal conductivity. J. Polym. Sci. Part B Polym. Phys. 2006, 44, 1513–1519. [CrossRef]
40. Ciecierska, E.; Boczkowska, A.; Kurzydlowski, K.J.; Rosca, L.D.; Hoa, S.V. The effect of carbon nanotubes on epoxy matrix
nanocomposites. J. Therm. Anal. Calorim. 2013, 111, 1019–1024. [CrossRef]
41. Martin, C.A.; Sandler, J.K.W.; Shaffer, M.S.P.; Schwarz, M.-K.; Bauhofer, W.; Schulte, K.; Windle, A.H. Formation of percolating
networks in multi-wall carbon-nanotube–epoxy composites. Compos. Sci. Technol. 2004, 64, 2309–2316. [CrossRef]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual
author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to
people or property resulting from any ideas, methods, instructions or products referred to in the content.