A single antenna for multiple bands are always beneficial from the design point of view. Here a single antenna which is fundamentally inverted F antenna is used, the uniqueness of the design is that , it uses trap technique to produce dual resonance from a single inverted F antenna . The trap used to block the current due to some frequencies and passes the current contributed by other frequencies. So in short , this trap is like a RF filter which has some passband as well as stop band. This trap approach uses a LC network to achieve this design goal .The two bands of interest are 865-870 MHz and 902-928 MHz .. The challenge of this design is that the frequency separation of the two bands is very small. In this case, and also the extra section for low frequency band is too small. Then, the influence of trap LC component variation due to tolerance to the two resonant frequencies is big, and so it is difficult to achieve good in band return loss within the LC tolerance. This is the main difficulty of this design. This issue is resolved by placing the low band section away from the end of the antenna. The antenna is designed on FR4 substrate material having thickness of 1.6 mm and hence it is a low cost solution which could use in various commercial applications which follows these bands.
Microstrip patch antenna for pcs and wlaneSAT Journals
Abstract Due to development in wireless devices, it poses a new challenge for the design of an antenna in wireless communication. Patch antennas are well suited for various wireless application systems due to their low weight, low profile, versatility, conformability, low cost and low sensitivity to manufacturing tolerances. This paper present design, simulation of a rectangular micro strip antenna for WLAN and PCS. The aim of the work is to design reliable broadband, compact patch antenna for wireless devices. Antenna is proposed which is providing circular polarization, dual band, resonant frequencies at 1.9 GHz, 2.4 GHz. Key Words: Patch antenna, co-axial feeding, polarization, dual band, HFSS …
Multiband Circular Microstrip Patch Antenna for WLAN Applicationtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
This paper presents the Microstrip patch antenna for WLAN applications with planar geometry and it consists of a defected ground (DGS), a feed, a substrate, and a patch. The design with DGS has been analyzed taking different dimensions of H Slot and achieve optimized dimensions with the help of CST, Microwave Studio commercial software for WLAN band at 5.20 GHz frequency with corresponding bandwidth of 310 MHz to optimize antenna’s properties. Results show that the final designed antenna has favorable characteristics at this frequency.
DESIGN & PARAMETRIC STUDY OF RECTANGULAR SLOT MICROSTRIP PATCH ANTENNA FOR UW...IJEEE
A Microstrip fed antenna which consists of a
rectangular patch with rectangular shaped slot incorporated
into patch is presented for ultra wide band application with
enhanced bandwidth. The proposed antenna achieves an
impedance bandwidth of 8.9GHz (2.3-11.2GHz) with
VSWR< 2 for over the entire bandwidth.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
Microstrip patch antenna for pcs and wlaneSAT Journals
Abstract Due to development in wireless devices, it poses a new challenge for the design of an antenna in wireless communication. Patch antennas are well suited for various wireless application systems due to their low weight, low profile, versatility, conformability, low cost and low sensitivity to manufacturing tolerances. This paper present design, simulation of a rectangular micro strip antenna for WLAN and PCS. The aim of the work is to design reliable broadband, compact patch antenna for wireless devices. Antenna is proposed which is providing circular polarization, dual band, resonant frequencies at 1.9 GHz, 2.4 GHz. Key Words: Patch antenna, co-axial feeding, polarization, dual band, HFSS …
Multiband Circular Microstrip Patch Antenna for WLAN Applicationtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
This paper presents the Microstrip patch antenna for WLAN applications with planar geometry and it consists of a defected ground (DGS), a feed, a substrate, and a patch. The design with DGS has been analyzed taking different dimensions of H Slot and achieve optimized dimensions with the help of CST, Microwave Studio commercial software for WLAN band at 5.20 GHz frequency with corresponding bandwidth of 310 MHz to optimize antenna’s properties. Results show that the final designed antenna has favorable characteristics at this frequency.
DESIGN & PARAMETRIC STUDY OF RECTANGULAR SLOT MICROSTRIP PATCH ANTENNA FOR UW...IJEEE
A Microstrip fed antenna which consists of a
rectangular patch with rectangular shaped slot incorporated
into patch is presented for ultra wide band application with
enhanced bandwidth. The proposed antenna achieves an
impedance bandwidth of 8.9GHz (2.3-11.2GHz) with
VSWR< 2 for over the entire bandwidth.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
MINIATURISATION OF PATCH ANTENNA USING NOVEL FRACTAL GEOMETRYIAEME Publication
In the Field of low profile antennamicro strip patch antennas have attracted many researchers due to small sizeand low cost of fabrication. One of trending member of new designs is Fractalantenna. Fractal shapes are recursive/repetitive self-similar geometries, dueto this self-similarity they can provide high gain, multiband, widebandsolutions and design miniature antenna. Fractal shapes are widely used incomputing, analysis and design; recent trends suggest positive outcomes ofusing fractal shapes in electromagnetics and communication system. In thispaper Jerusalem cube fractal shape is introduced in probe fed conventionalpatch antenna for L1 band. A dual band antenna resonating at 1.41 GHz (L) and3.37 (S) GHz, band is constructed using said fractal shape.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
Planar Internal Antenna Design for Cellular Applications & SAR AnalysisIJERD Editor
This paper presents a new design of direct-fed Multi band printed Planar Internal Antenna (PIA), for
cellular applications. The PIA antenna is composed of ground plane, meander radiating strip and two other
parasitic strips are printed on a common substrate. The designed antenna has been simulated in CST
environment. The simulated results for the resonant frequency, return loss, radiation pattern and gain are
presented and discussed. The bandwidths for three resonance achieved on the basis of -6 dB return loss.These
Bandwidths can be utilized for GSM 900, GSM 1800, GSM 1900, LTE 2300 and Bluetooth/WLAN as an
acceptable reference in mobile phones applications. Further the antenna was placed in proximity to the SAR
head on CST environment. The simulated results of SAR analysis are presented in this paper with acceptable
range.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
A Compact Reconfigurable Dual Band-notched Ultra-wideband Antenna using Varac...TELKOMNIKA JOURNAL
In this paper, a reconfigurable dual band-notched ultra-wideband (UWB) antenna is presented.
The antenna design consists of a circular shape with two pairs of the L-resonator. To realize the notch
characteristics in WLAN at 5.2 GHz and 5.8 GHz bands, the half wavelength of the L-resonator is
introduced in the design. The T-shaped notch is etched in the ground to enhance the bandwidth which
covers the UWB operating frequency range from 3.219–10.863 GHz. The proposed reconfigurable dual
band-notched UWB antenna shows good impedance matching for the simulated in the physical layout.
Furthermore, the proposed antenna has a compact size of 37.6x28 mm2. This proposed reconfigurable
design can provide an alternative solution for the wireless system in the designing of a band-notched
antenna with a good tuning capability.
Bandwidth enhancement of rectangular microstrip patch antenna using slotsIOSR Journals
In this paper, a new design of rectangular microstrip patch antenna (RMPA) without slot, with slots
and array is proposed and analyzed. The designed antenna has been simulated using HFSS software. The
simulated results for return loss, radiation pattern and gain are presented and discussed. The bandwidth of
proposed antenna is 2.4GHz-5.9GHz for VSWR(voltage standing wave ratio)<2><-
10dB return loss as an acceptable reference in wireless applications which cover worldwide interoperability for
microwave access (WiMAX) and wireless local area network (WLAN) and other applications. Gain of 10dB is
achieved for antenna array.
Bandwidth enhancement of rectangular microstrip patch antenna using slotsIOSR Journals
Abstract : In this paper, a new design of rectangular microstrip patch antenna (RMPA) without slot, with slots and array is proposed and analyzed. The designed antenna has been simulated using HFSS software. The simulated results for return loss, radiation pattern and gain are presented and discussed. The bandwidth of proposed antenna is 2.4GHz-5.9GHz for VSWR(voltage standing wave ratio)<2><-10dB return loss as an acceptable reference in wireless applications which cover worldwide interoperability for microwave access (WiMAX) and wireless local area network (WLAN) and other applications. Gain of 10dB is achieved for antenna array. Keywords- Array, Microstrip antenna, WLAN, WiMAX
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
More Related Content
Similar to DUAL BAND F-ANTENNA FOR EUROPE AND NORTH AMERICA
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
MINIATURISATION OF PATCH ANTENNA USING NOVEL FRACTAL GEOMETRYIAEME Publication
In the Field of low profile antennamicro strip patch antennas have attracted many researchers due to small sizeand low cost of fabrication. One of trending member of new designs is Fractalantenna. Fractal shapes are recursive/repetitive self-similar geometries, dueto this self-similarity they can provide high gain, multiband, widebandsolutions and design miniature antenna. Fractal shapes are widely used incomputing, analysis and design; recent trends suggest positive outcomes ofusing fractal shapes in electromagnetics and communication system. In thispaper Jerusalem cube fractal shape is introduced in probe fed conventionalpatch antenna for L1 band. A dual band antenna resonating at 1.41 GHz (L) and3.37 (S) GHz, band is constructed using said fractal shape.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
Planar Internal Antenna Design for Cellular Applications & SAR AnalysisIJERD Editor
This paper presents a new design of direct-fed Multi band printed Planar Internal Antenna (PIA), for
cellular applications. The PIA antenna is composed of ground plane, meander radiating strip and two other
parasitic strips are printed on a common substrate. The designed antenna has been simulated in CST
environment. The simulated results for the resonant frequency, return loss, radiation pattern and gain are
presented and discussed. The bandwidths for three resonance achieved on the basis of -6 dB return loss.These
Bandwidths can be utilized for GSM 900, GSM 1800, GSM 1900, LTE 2300 and Bluetooth/WLAN as an
acceptable reference in mobile phones applications. Further the antenna was placed in proximity to the SAR
head on CST environment. The simulated results of SAR analysis are presented in this paper with acceptable
range.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
A Compact Reconfigurable Dual Band-notched Ultra-wideband Antenna using Varac...TELKOMNIKA JOURNAL
In this paper, a reconfigurable dual band-notched ultra-wideband (UWB) antenna is presented.
The antenna design consists of a circular shape with two pairs of the L-resonator. To realize the notch
characteristics in WLAN at 5.2 GHz and 5.8 GHz bands, the half wavelength of the L-resonator is
introduced in the design. The T-shaped notch is etched in the ground to enhance the bandwidth which
covers the UWB operating frequency range from 3.219–10.863 GHz. The proposed reconfigurable dual
band-notched UWB antenna shows good impedance matching for the simulated in the physical layout.
Furthermore, the proposed antenna has a compact size of 37.6x28 mm2. This proposed reconfigurable
design can provide an alternative solution for the wireless system in the designing of a band-notched
antenna with a good tuning capability.
Bandwidth enhancement of rectangular microstrip patch antenna using slotsIOSR Journals
In this paper, a new design of rectangular microstrip patch antenna (RMPA) without slot, with slots
and array is proposed and analyzed. The designed antenna has been simulated using HFSS software. The
simulated results for return loss, radiation pattern and gain are presented and discussed. The bandwidth of
proposed antenna is 2.4GHz-5.9GHz for VSWR(voltage standing wave ratio)<2><-
10dB return loss as an acceptable reference in wireless applications which cover worldwide interoperability for
microwave access (WiMAX) and wireless local area network (WLAN) and other applications. Gain of 10dB is
achieved for antenna array.
Bandwidth enhancement of rectangular microstrip patch antenna using slotsIOSR Journals
Abstract : In this paper, a new design of rectangular microstrip patch antenna (RMPA) without slot, with slots and array is proposed and analyzed. The designed antenna has been simulated using HFSS software. The simulated results for return loss, radiation pattern and gain are presented and discussed. The bandwidth of proposed antenna is 2.4GHz-5.9GHz for VSWR(voltage standing wave ratio)<2><-10dB return loss as an acceptable reference in wireless applications which cover worldwide interoperability for microwave access (WiMAX) and wireless local area network (WLAN) and other applications. Gain of 10dB is achieved for antenna array. Keywords- Array, Microstrip antenna, WLAN, WiMAX
Similar to DUAL BAND F-ANTENNA FOR EUROPE AND NORTH AMERICA (20)
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
1. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
DOI:10.5121/ijwmn.2023.15301 1
DUAL BAND F-ANTENNA FOR EUROPE AND
NORTH AMERICA
Prasad Samudrala, Justin Jose and Amit Kulkarni
Honeywell Building Technologies, Advanced Technology Group, Honeywell Inc.
ABSTRACT
A single antenna for multiple bands are always beneficial from the design point of view. Here a single
antenna which is fundamentally inverted F antenna is used, the uniqueness of the design is that , it uses
trap technique to produce dual resonance from a single inverted F antenna . The trap used to block the
current due to some frequencies and passes the current contributed by other frequencies. So in short , this
trap is like a RF filter which has some passband as well as stop band. This trap approach uses a LC
network to achieve this design goal .The two bands of interest are 865-870 MHz and 902-928 MHz .. The
challenge of this design is that the frequency separation of the two bands is very small. In this case, and
also the extra section for low frequency band is too small. Then, the influence of trap LC component
variation due to tolerance to the two resonant frequencies is big, and so it is difficult to achieve good in
band return loss within the LC tolerance. This is the main difficulty of this design. This issue is resolved by
placing the low band section away from the end of the antenna. The antenna is designed on FR4 substrate
material having thickness of 1.6 mm and hence it is a low cost solution which could use in various
commercial applications which follows these bands.
KEYWORDS
Trap , SubGHz , inverted F antenna, FR4 substrate , LC Component
1. INTRODUCTION
Adding traps on antenna is a commonly used method to make multiband antennas. In [1], this
method was used to design Dual-Band PIFA. In [2], traps were added to wires to make Dual-Band
Quadrifilar Helix Antenna. In [3], the trap method was used not just to design multiband antenna,
but to design broad band antenna. In this paper, the trap method is used to design a dual band
printed F-Antennas. The design consists of an inverted F antenna, with a trap for creating the dual
bands. The two bands are 865-870 MHz and 902-928 MHz. The design goal is that, the return loss
for the two bands is under -10dB within the trap LC component tolerance. For trap F-antenna, a
straight forward configuration of the antenna is shown in Fig. 1. A), where the low band section is
at the end of the antenna. But this configuration will not work for this antenna design, because the
separation of the two bands is small, and thus that section is small. And because this section is
small, the influence of trap L and C components variation due to tolerance to the two resonant
frequencies is big. Actually, it is too big. It is not possible to achieve the design goal, which is, the
return loss for the two bands is under -10dB within trap LC component tolerance. To solve this
problem, the low band section is placed away from the end of the antenna as shown in Fig. 1. B),
so it becomes bigger. When it is bigger, the LC tolerance’s influence is smaller, then the design
goal is achieved. The first part of the paper describes the design of the trap, second part will
present the inverted F-Antenna design. The antenna is designed to be printed on FR-4 material to
minimize space and cost of the board. For all simulations, the software used in the designs is CST
(Computer Simulation Technology).
2. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
2
a) Low band section is at the antenna end.
6) Low band section is away from the antenna end
Figure 1. Two congurations of trap antenna
2. THE TRAP DESIGN
The Trap used in the design are as follows. It consists of one capacitor and two inductors
connected in parallel which acts as a band stop filter for high band. The reason of using two
inductors in parallel is for getting the required value.
LC selection: the readily available tolerance for C is +-0.05pF but up to the value 9.1pF in a
popular source. For the percentage reason, the highest value 9.1pF is selected. The L value is
selected to make the LC trap resonating at 915MHz. The readily available tolerance for L is +-2%.
The selected capacitor and inductor nominal values and tolerances are C=9.1pF+-0.05pF,
L=6.8nF+-0.02%. The trap S21 with the nominal values, and the two ends of tolerances are shown
in Figure . 2. Trap S21 variation due to tolerance is clearly seen.
Figure 2 . Trap used in the design
3. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
3
3. THE F-ANTENNAS DESIGN WITH TRAP
The inverted F antenna design, as shown in Figure . 3, combines a single inverted F antenna with a
trap. The ground plane is modeled as 1.6 mm thick,100x100mm PEC. The antenna area is 13.5
mm wide FR4 (Er 4.3, LossTan 0.025). The antenna dimensions are 59.4x11 mm, antenna trace is
2.7 mm wide, feed width is 0.65 mm, antenna PEC thickness is 0.035 mm. Fig. 5 shows the
antenna return loss with trap LC nominal values, and the two ends of tolerances. As can be seen,
the design goal is achieved, which is, under -10dB for all cases.
(a) whole PCB
(b) Antenna details
Figure 3 . The design. (a) whole PCB (b) Antenna details
4. IMPEDANCE MATCHING FOR THE DUAL BAND F ANTENNA :
Most common wireless circuits are matched to 50 ohm at the antenna input .When RF engineers
think about the impedance of their project’s transmission lines, they may automatically assume
that these lines all have a nominal impedance of 50 ohms (Ω). That makes sense, as so much of
today’s RF design work is based around that value. It’s not an arbitrary number; there are good
technical reasons for using 50 Ω.
4. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
4
Figure 4 : Comparison of characteristics impedance for max power, low attenuation
As in figure 4, Their analysis looked at the performance of three characteristics as a function of
impedance and they found:
1: Attenuation (loss) is largely a function of the dielectric in the cable. For the air-filled
coaxial cable which they analyzed, the lowest loss was at about 77 Ω (it is around 50 Ω
for some dielectrics, but such cables did not yet exist).
2: The voltage maximum is a function of the intensity of the electric field between the
coaxial outer conductor and the inner conductor. For coaxial cable supporting RF signals
in the TE10 electromagnetic (EM) field waveguide mode, the e-field has its maximum at
around 60 Ω.
3: The power handling capability is determined by the breakdown field and impedance
(V2
/Z). For air-filled coaxial cables operating below the TE11 mode cutoff frequency, the
power transfer is at its maximum at around 30 Ω.
In this design , the antenna input impedance is matched to 50 ohm for maximum power transfer
and thereby achieving better efficiency of radiation . The Figure 7 below shows the Smith Chart
representation of the impedance matching at two frequency points 866 MHz & 901 MHz , which
are in the Europe & NA bands .
5. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
5
Figure 5 : Smith Chart for impedance matching 866 MHz & 901 MHz
As in Figure 5 , the complex impedance is ( 49.6-j0.685 ) ohm for 866 Mhz and (50.9+j1.7) ohm
. Thus it can be concluded that the two frequency points in the band of interest are very closely
matched to 50 ohm impedance and the return loss is well below -10 dB standard .
5. RESULTS & ANALYSIS
This section deals with the results of the propsoed Dual band Sub GHz antenna . It mainly
includes the Surface current distribution, Return Loss ( dB) , 3D Radiation pattern & Antenna
efficiency (dB ).
Figure 6. Antenna return loss
The Antenna return loss plot in Figure 6., shows the bandwidth numbers, which is more than 20
MHz for the 868 MHz band (Europe ) &approx.. 50 MHz for 915 MHz which is well beyond the
bandwidth requirements .
As in Figure 7 , the surface current distribution shows strong current distribution along the
antenna traces , at both the SubGHz bands , 866 MHz & 915 MHz respectively
6. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
6
Figure 7 . Surface current distribution at 866 MHz& 915 MHz
7. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
7
Figure 8. 3D Radiation Patterns
Figure 9 : 2 D Radiation Patterns
The three dimensional Radiation patterns shown in Figure 8 ., states that the antenna radiates a
quasi omni directional pattern and having an efficiency of above 82 % for both the Sub GHz
bands . The Figure 9 shows the corresponding two dimensional antenna radiation patterns at 866
MHz and 915 MHz respectively .
8. International Journal of Wireless & Mobile Networks (IJWMN), Vol.15, No.2/3, June 2023
8
6. CONCLUSION
In this paper, inverted F-antenna with trap is used to design dual band (860-870 MHz & 902-928
MHz) F-antenna, with partial omni directional pattern. The antenna is printed on FR4 board for
low cost. Normally the low band section of a trap antenna is placed at the end of the antenna. But
it does not work when the two bands separation is small due to LC value tolerance. The problem
is solved by placing the low band section away from the end of the antenna. This design meets
the bandwidth, efficiency and radiation pattern requirements. It offers the design benefits like low
cost , small form factor which could potential aid the commercial designs.
REFERENCES
[1] G. K .H. Lui, and R. D. Murch, “Compact dual-frequency PIFA designs using LC resonators,”
Antennas and Propagation, IEEE Transactions on., Volume: 49, Issue: 7, 2001
[2] D. Lamensdorf, and M. A.Smolinski, “Dual-band quadrifilar helix antenna, ” IEEE Antennas and
Propagation Society International Symposium, 2002. Vol. 3, Pages: 488 – 491
[3] D. D. Reuster, “A high-efficiency broadband HF wire-antenna system,” IEEE Antennas and
Propagation Magazine, Year: 2000, Volume: 42, Issue: 4, Pages: 53 – 69.
[4] https://resources.altium.com/p/mysterious-50-ohm-impedance-where-it-came-and-why-we-use-it
[5] https://www.digikey.in/en/blog/the-reasons-for-50-ohm-and-75-ohm-transmission-lines
[6] https://www.digikey.in/en/articles/the-smith-chart-an-ancient-graphical-tool-still-vital-in-rf-design
AUTHORS
Prasad Samudrala has master’s degree in Information and communications engineering
from Anna University, Chennai. He has over 19 years of experience in Industrial and
building automation, IoT, Wireless and Embedded product development. He has over 25
patents and 3 trade secrets to his name. Currently he is in a Principal System Architect
position in Honeywell building automation division. His area of interest include Low
power wireless technologies, 5G.
Justin Jose is Sr. RF Engineer in Honeywell Building Technologies group. He has more
than 8 years of Industrial experience and holds Master Degree in Electronics &
Communication Engineering, specialized in Microwave & Antennas from Cochin
University of Science & Technology, India. Main areas of interest include Antenna, RF &
Wireless Communication and worked in Fixed Wireless, Automotive and Consumer
Electronics domains. He has got 2 patents filed and continuing the R& D on various existing & futuristic
Wireless technologies.
Amit Kulkarni is an Engineering Director in HBT Architecture and Innovation team. He
also leads the Wireless COE. Amit joined Honeywell in October 2008. Before joining
Honeywell, he worked in General Electric Global Research as a Senior Scientist and then
became Sr Engineering Manager at GE Security. Amit has 23 years of experience in
Wireless Communication Systems. He holds a Ph.D in Computer Science from the
University of Kansas. He is an inventor on more than 25 patents and has published 17 papers in various
journals and conferences.