It covers complete R.C.C. slab casting procedure and important points related to the process such as recommended mix design, cube/slump tests, recommended values of concrete slump test for various purposes, walkways/platforms for casting purposes, concrete unloading, spreading, compaction and curing.
2. RCC SLAB | 1
CHAPTER- 9 RCC आर.सी.सी.
A. MATERIALS मटीररयल्स
1. River Sand
बजरी
2. Cement
सीमेंट
3. Gravel/Grit
रोडी
B. SAFETY AND CONSTRUCTION EQUIPMENTS सुरक्षा और कं स्ट्रक्शन के उपकरण
1. Builder’s Hat (Helmet)
हेलमेट
2. Safety Jackets
सुरक्षा जैके ट्स
3. RCC SLAB | 2
3. Gloves
ग्लव्स
4. Concrete Boots
जूते
5. Cone- for slump test
कोन- स्लंप टेस्ट के ललए
6. Measuring Flask- for plasticizer
मेज़ररंग फ्लास्क- प्लास्टस्टसाइज़र के ललए
7. Concrete molds- for Cube test
(minimum 6)
कं क्रीट के मोल्ड्स- क्यूब टेस्ट के ललए (कम से
कम 6)
5. RCC SLAB | 4
13. Various containers- to measure water
लवलिन्न तरह के पात्र- पानी मापने के ललए
14. Measuring boxes- for fine and coarse
aggregates
मेज़ररंग बॉक्स- बजरी, सीमेंट और रोडी के ललए
15. Trolley or Wheel barrow
टरॉली या व्हील बैरो
16. RCC Slab Trolley
RCC स्लैब टरॉली
6. RCC SLAB | 5
C. RCC CASTING PROCEDURE AND IMPORTANT POINTS आर.सी.सी. डालने की प्रक्रिया और
ज़रूरी बातें
1. All the Raw materials (Natural Sand/ M-Sand, Cement, Aggregates, Water, and
Recommended Admixture) should be tested before use in the laboratory and should be
followed.
सारे कच्चे माल (प्राकृ लतक बजरी / M-बजरी, सीमेंट, रोडी, पानी और रेकमेंडेड एडलमक्सचर) की, इस्तेमाल करने
से पहले, लेबोरेटरी में जांच करना और उसका पालन करना ज़रूरी है।
2. Follow recommended mix design while concreting, based on material testing report.
कं क्रीट डालते समय, मटीररयल टेस्टस्टंग ररपोटा के आधार पर लिए गए रेकमेंडेड क्रमक्स क्रडज़ाईन का पालन करें।
3. Mix ingredients by weight or using weigh-batcher.
Use measuring boxes to load fine and coarse aggregate in mortar mixer.
Control, monitor and measure quantity of water and plasticizer.
सामग्री को उनके वज़न के अनुसार या कं क्रीट-वे-बैचर की मिि से लमलाएं ।
बजरी, सीमेंट और रोडी को मोटाार लमक्सर में डालते समय मेज़ररंग बॉक्सेस का इस्तेमाल करें।
पानी और प्लास्टस्टसाइज़र की मात्रा को लनयंलत्रत रखें, जांच करें और मापें।
4. Perform Cube Test: क्यूब टेस्ट् करें:
The minimum frequency of sampling of concrete of each grade shall be in accordance with
the following:
प्रत्येक ग्रेड के कं क्रीट की सैंपललंग की न्यूनतम संख्या लनम्नललस्टखत के अनुसार होगी:
Quantity of concrete in the work, m3
काम में आने वाले कं िीट की मात्रा, m3
Number of Samples
सैंपल की संख्या
1-5 1
6-15 2
16-30 3
31-50 4
51 and above
51 या ज़्यािा
4 plus one additional sample for each additional
50 m3 or part thereof
4 + एक अलतररक्त सैंपल, हर 50 m3
अलतररक्त मात्रा या
उसके िाग के ललए
Note: At least one sample shall be taken from each shift. Where concrete is produced at
continuous production unit, such as ready-mixed concrete plant, frequency of sampling may
be agreed upon mutually by suppliers and purchasers.
नोट: हर लिफ्ट में से कम से कम एक सैंपल लें। जहााँ कं क्रीट लनरंतर प्रोडक्शन यूलनट पर उत्पालित लकया जाता है,
7. RCC SLAB | 6
जैसे की रेडी-लमक्स्ड कं क्रीट प्लांट में, वहां सैंपललंग की संख्या क्या होनी है, इसका लनर्ाय बेचने वाले और
खरीिारों के आपसी सहमलत से लकया जायेगा।
5. Crosscheck slump at pre-decided intervals but minimum for 6 times and simultaneously fill
up concrete molds also for cube testing. (Prefer slump test near concreting location) (Image
1)
पूवा-लनलित अंतराल पर स्लंप को क्रॉसचेक करें, कम से कम 6 बार, और इसके साथ ही क्यूब टेस्ट के ललए कं क्रीट
मोल्ड्स को िी िरें। (स्लंप टेस्ट को कं क्रीट डालने वाली जगह पर ही करें) (क्रित्र 1)
Recommended Values of Concrete Slump Tests for Various Purposes:
क्रवक्रिन्न कायों के क्रलए कं िीट स्लंप टेस्ट् के रेकमेंडेड मूल्य:
No.
संख्या
Types of concrete
कं क्रीट के प्रकार
Slump
स्लंप
1. Concrete for road construction
सडक बनाने के ललए कं क्रीट
20 to 40 mm
2. Concrete for tops of kerbs, parapets, piers, slabs and wall
फु टपाथ के ऊपरी सतह, पैरापेट, पायसा, स्लैब्स और िीवारों के ललए
कं क्रीट
40 to 50 mm
3. Concrete for canal lining
कै नाल लाइलनंग के ललए कं क्रीट
70 to 80 mm
4. Normal RCC work
साधारर् आर.सी.सी. के काम के ललए
80 to 150 mm
5. Mass concrete
लविाल कं क्रीट के काम के ललए
20 to 50 mm
6. Concrete, where vibration takes place
कं क्रीट, जहााँ वाइब्रेिन होता हो
10 to 25 mm
Image 1: Slump test using Cone
8. RCC SLAB | 7
6. Prepare concrete and transfer it rapidly
using trolley or wheel barrow to
prevent segregation or loss of any
ingredient or entrance of foreign matter
or water. (Image 2)
कं क्रीट तैयार करें और टरॉली या व्हील बैरो की
मिि से इसे जल्दी से टरांसफर करें लजससे सामग्री
अलग-अलग ना हो जाये या लकसी सामग्री का
नुक्सान ना हो तथा लकसी तरह का बाहरी
मटीररयल या पानी ना आ सके । (क्रित्र 2)
It is recommended to discharge the
concrete within 90 minutes from the
batching plant loading time.
कं क्रीट को बैलचंग प्लांट के लोलडंग समय के 90
क्रमनटों के अंदर ही लनकाल िें।
7. Take necessary care to avoid
displacement of reinforcement or
formwork.
रीइंफोर्स्मेंट या फॉमावका के लबगडने से बचने के
ललए ज़रूरी िेखिाल करें।
Make proper walkways/ platforms so
that the supports of the pipeline and
labour do not directly stand on
reinforcement. (Image 3)
चलने के ललए उलचत रास्ते या प्लेटफामा बनाएं
लजससे पाइपलाइन के सपोट्ास या लफर लेबर
रीइंफोर्स्मेंट पर एकिम ना खडे हो। (क्रित्र 3)
Note: Pathways are created time and
again as per the locations of pouring
concrete.
नोट: कं क्रीट डालने के ललए ऐसे रास्ते कई बार
बनाने पडते हैं।
8. The concrete shall be unloaded as
nearly as practicable to its final position.
कं क्रीट को लजतना हो सके उसी जगह के पास
उतारें जहााँ उसे डालना है।
Image 2: Transferring concrete in wheel barrow
Image 3: Walkways/Platforms for labour
9. RCC SLAB | 8
When the concrete is lifted up, use RCC
slab trolley to unload it and do not
unload it directly on slab. (Image 4)
जब कं क्रीट ऊपर आये तब उसे आर.सी.सी. स्लैब
टरॉली की मिि से उतारें और एकिम स्लैब पर ना
उतारें। (क्रित्र 4)
Note: The maximum permissible free
fall of concrete maybe taken as 1.5 m.
नोट: कं क्रीट का अलधकतम अनुमत फ्री फॉल 1.5
m हो सकता है।
9. Move RCC slab trolley on the walkway to
pour the concrete on reinforcement.
(Image 5)
कं क्रीट को रीइंफोर्स्मेंट पर डालने के ललए
आर.सी.सी. टरॉली को बनाये गए रास्ते पर चलाएं ।
(क्रित्र 5)
10. Start pouring the concrete first on the
reinforcement towards the opposite
end. (Image 6)
सबसे पहले सामने या लवपरीत तरफ के
रीइंफोर्स्मेंट पर कं क्रीट डालें। (क्रित्र 6)
11. Thoroughly compact and work concrete
around the reinforcement, around
embedded fixtures and into corners of
formwork.
Image 5: Moving RCC Slab Trolley on walkway
Image 6: Pouring concrete, first towards opposite side
Image 4: Unloading the concrete in RCC Slab
Trolley
10. RCC SLAB | 9
कं क्रीट को अच्छे से रीइंफोर्स्मेंट के आस-पास,
एम्बेडेड लफक्स्चर के आस-पास और फॉमावका के
कोनों में डालें और कॉम्पैक्ट करें।
Use rods & mechanical vibrators for
compaction. (Image 7)
कम्पैक्शन के ललए रॉड्स और मेके क्रनकल
वाइब्रेटर इस्तेमाल करें। (क्रित्र 7)
Use Plate vibrator or Power Float to
level the concrete homogenous. (Image
8)
कं क्रीट को समतल करने के ललए प्लेट वाइब्रेटर
या पावर फ्लोट इस्तेमाल करें। (क्रित्र 8)
Note: Over vibration and under
vibration of concrete are harmful and
should be avoided. Avoid vibration of
very wet mixes.
नोट: कं क्रीट में ज़रूरत से ज़्यािा या बहुत कम
वाइब्रेिन ना करें, यह हालनकारक है। बहुत गीले
कं क्रीट लमक्स को िी लवब्रेट ना करें।
11. Avoid walking on the concrete after casting. Use tarpaulin to protect it from rain or excess
heat.
कं क्रीट डालने के बाि उस पर ना चलें। बाररि और अलधक गमी से बचाने के ललए कं क्रीट पर तारपोललन इस्तेमाल
करें।
12. Start Curing immediately after thumb
set of laid concrete. Earth or sand dykes
(क्यारी) around concrete surface’s
perimeter should be made for curing.
Cure for at least 15 days. (Image 9)
कं क्रीट के थंब सेट होने के एकिम बाि तराई
िुरू कर िें। तराई करने के ललए कं क्रीट सतह के
घेरे के आस-पास क्यारी बनाएं और उस क्यारी में
15 लिन तक पानी िाल कर रखें। (क्रित्र 9)
(Refer Chapter-7 Curing for details)
(अक्रिक जानकारी के क्रलए िैप्टर-7 तराई
देखें)
Image 9: Curing of RCC Slab
Image 7: Compaction through Mechanical Vibrator
Image 8: Levelling through Power Float