• Single bag up to 5 bag filters • Pre-Filtration • Low running costs • Cheap costs - bag replacement • Flow rates from 1-2500 lpm • 1 micron - 25 micron rating • ISO cleanliness 18/16/13 • Stainless steel housing • Pressure rating 10 bar

1. Tel: 011 864 1404 9 Jurie Street P O Box 17639
Fax: 011 864 1407 Alrode Randhart
Email: info@mhpumps.co.za 1449 1457
CK 1991/027957/23 Member: K.Magill VAT Nr 4090127483 1
Pump Services CC
Diesel fuel filtration
Based on the above the following filter system is to be used on all sites and
may vary depending on flow and volume requirements, the flow
calculations and ISO cleanliness specifications will be based on a receiving
flow of 1000LPM and a dispensing flow of 500LPM using the same filters or
filter skid.
The diagrams below shows the general layout of what is required
Pre-filters

2. Tel: 011 864 1404 9 Jurie Street P O Box 17639
Fax: 011 864 1407 Alrode Randhart
Email: info@mhpumps.co.za 1449 1457
CK 1991/027957/23 Member: K.Magill VAT Nr 4090127483 2
Pump Services CC
Pre filtration is a cost saving tool where the bulk of the dirt or particulate
can be captures by a relatively cheap filter, thus saving running costs and
avoids down time
The following specifications of equipment are required for Pre filtration:
FILTER BAG
Nominal Micron rating: 1 Micron
Quantity’s: Three bags
Size: 790mm length x 190mm OD
polypropylene woven media
Weight GM/M2: 390g averages
Maximum temperature: 130°C
Thread for sewing bags: Continuous filament polyester thread.
780 50 Tex
Flow rate 1000LPM for 3 bags at 4 Cst
Pressure: Recommended change out DP 80Kpa
differential

3. Tel: 011 864 1404 9 Jurie Street P O Box 17639
Fax: 011 864 1407 Alrode Randhart
Email: info@mhpumps.co.za 1449 1457
CK 1991/027957/23 Member: K.Magill VAT Nr 4090127483 3
Pump Services CC
FILTER HOUSING
 Construction: Stainless steel 304
 Flanges: 6” with step down flanges to 3”
 Pressure rating: 10 bar Max 6 bar operating with a
13bar Hydro test (NDT)
 Opening: Swing bolts
 Sealing: O-Ring configuration
 Ports: For air release and drain and DP
Gauges
Filtration/Coalescer separation-filters
The filtration and Coalescer separator combination is to insure that
the ISO cleanliness levels are maintained and that the water is
removed.
The following specifications of equipment are required for filtration
Coalescer separation:

4. Tel: 011 864 1404 9 Jurie Street P O Box 17639
Fax: 011 864 1407 Alrode Randhart
Email: info@mhpumps.co.za 1449 1457
CK 1991/027957/23 Member: K.Magill VAT Nr 4090127483 4
Pump Services CC
FILTER ELEMENTS
Nominal Micron rating: 25 Micron
Quantity’s: Eight Coalescer and five separators
Maximum temperature: 80°C
Flow rate 1000LPM at 4 Cst
Pressure: Recommended change out DP 100 Kpa
differential.
FILTER HOUSING
Construction: Carbon steel epoxy coating
Flanges: 4” simplex configuration
Pressure rating: 10 bar Max 6 bar operating with a 13bar
Hydro test (NDT)
Opening: Swing bolts
Sealing: O-Ring configuration
Ports: For air release and drain, inspection
holes are required and DP gauges
Supports: David arm