This document provides instructions on how to use operating modes in Ecodial Advance Calculation 4 software. It describes visualizing the different operating modes, personalizing a new operating mode, and applying it to a project. The steps include visualizing existing operating modes, personalizing a new mode by modifying component properties as needed, and applying the new mode to the entire project. The goal is to understand how to customize operating modes to model different normal and emergency scenarios.

1. 1
Ecodial Advance Calculation 4
2013
N°1: How to personalize a component and apply
a property to all the project?
Schneider Electric 2
- Customer Software– Ecodial 4 – Training (C) - 2013
N°1 - How to personalize a component
and apply a property to all the project
●Objective
● To be able to …
● visualize the different component
● personalize the properties of a component
● apply to all the project

2. 2
Schneider Electric 3
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● Select a circuit (cable)
● Visualise the characteristics of the cable (insulation)
● Visualise the window with all cables
● Personalize
● Change the type of insulation (XLPE in PVC)
● Apply
● Copy and paste to apply to all the selection
● Result
N°1 - How to personalize a component
and apply a property to all the project
Schneider Electric 4
- Customer Software– Ecodial 4 – Training (C) - 2013
●Select a cable
N°1 - How to personalize a component
and apply a property to all the project

3. 3
Schneider Electric 5
- Customer Software– Ecodial 4 – Training (C) - 2013
N°1 - How to personalize a component
and apply a property to all the project
●How to check the insulation type ?
Schneider Electric 6
- Customer Software– Ecodial 4 – Training (C) - 2013
N°1 - How to personalize a component
and apply a property to all the project

4. 4
Schneider Electric 7
- Customer Software– Ecodial 4 – Training (C) - 2013
N°1 - How to personalize a component
and apply a property to all the project
●How to check the insulation type ?
Schneider Electric 8
- Customer Software– Ecodial 4 – Training (C) - 2013
●Personalize - Change the type of insulation (XLPE to PVC)
N°1 - How to personalize a component
and apply a property to all the project

5. 5
Schneider Electric 9
- Customer Software– Ecodial 4 – Training (C) - 2013
●Apply – “ copy “ with “ ctrl + C “
copy
N°1 - How to personalize a component
and apply a property to all the project
Use the keyboard :
ctrl C
Schneider Electric 10
- Customer Software– Ecodial 4 – Training (C) - 2013
●Apply - « copy-paste » to apply it to all the selection
N°1 - How to personalize a component
and apply a property to all the project
shift

6. 6
Schneider Electric 11
- Customer Software– Ecodial 4 – Training (C) - 2013
●Apply - « paste » to apply it to all the selection
N°1 - How to personalize a component
and apply a property to all the project
Use the keyboard
:
ctrl V
Schneider Electric 12
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 - Creation
●B) Mars 2011- Vérification et 1ère phase d’harmonisation
●C) Mars 2012 - Updating

7. 7
Schneider Electric 13
- Customer Software– Ecodial 4 – Training (C) - 2013
N°1 - How to personalize a component and apply a property to all the project
●How to personalize the insulation type ?
Schneider Electric 14
- Customer Software– Ecodial 4 – Training (C) - 2013
Exercice N°1
Change the type of insulation (XLPE to PVC)

8. 8
Ecodial Advance Calculation 4
2013
N°2: How to personalize a protection settings?
Schneider Electric 16
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Objective
● To be able to …
● Check the projection of the installation
● Optimize the discrimination
● Apply the modification

9. 9
Schneider Electric 17
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● Single line diagram
● Results of calculation and « alarms »
● Data visualisation: the data, the calculation results and the solutions
● Circuit properties and component properties
● The details results of a circuit, the protection curves
● Personalize
● Modification of a component
● Checking of discrimination
● Curve settings
● Obtain total discrimination
N°2: How to personalize a protection
settings?
Schneider Electric 18
- Customer Software– Ecodial 4 – Training (C) - 2013
●Single line diagram (Loads ,cables, Ks…)
N°2: How to personalize a protection
settings?

10. 10
Schneider Electric 19
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Results of calculation
Schneider Electric 20
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Results of calculation

11. 11
Schneider Electric 21
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Data visualisation
Schneider Electric 22
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Calculation visualisation

12. 12
Schneider Electric 23
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Solution visualisation
Schneider Electric 24
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Circuit properties visualisation

13. 13
Schneider Electric 25
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Component properties visualisation
Schneider Electric 26
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●QA7: Circuit breaker properties visualisation

14. 14
Schneider Electric 27
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Circuit “details”
Schneider Electric 28
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Curves visualisation

15. 15
Schneider Electric 29
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Curves visualisation
Schneider Electric 30
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
What to do to obtain a total discrimination ?

16. 16
Schneider Electric 31
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
Schneider Electric 32
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?

17. 17
Schneider Electric 33
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
2,5 x
Schneider Electric 34
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings? 100
160
250
400
630
800
1000
1250
1600
2000
2500
3200
4000
2,5 x
2,5 x
2,5 x
2,5 x

18. 18
Schneider Electric 35
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
Schneider Electric 36
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection

19. 19
Schneider Electric 37
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
Schneider Electric 38
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection

20. 20
Schneider Electric 39
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
Schneider Electric 40
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Just remind !

21. 21
Schneider Electric 41
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
Schneider Electric 42
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection

22. 22
Schneider Electric 43
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●Personalize a protection
Schneider Electric 44
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection
settings?
●The CSA of cable N°3 has not change(thanks to Micrologic 5)

23. 23
Schneider Electric 45
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 - Creation
●B) Mars 2011- Vérification et 1ère phase d’harmonisation
●C) Mars 2012- Up dating
Schneider Electric 46
- Customer Software– Ecodial 4 – Training (C) - 2013
N°2: How to personalize a protection settings?

24. 24
Schneider Electric 47
- Customer Software– Ecodial 4 – Training (C) - 2013
Exercice N° 2
How to personalize a protection settings?
Ecodial Advance Calculation 4
2013
N°3: How to harmonize a protection schedule?

25. 25
Schneider Electric 49
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective:
● To be able to …
● Check the protection of the project
● Optimize the discrimination
● Apply the modifications to the project
N°3: How to harmonize a protection schedule ?
Schneider Electric 50
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● A component (Circuit breaker)
● The data table
● The result table
● Personalize
● Harmonize the Micrologic
● Modify the trip unit
● Select the Micrologic 5
● Check the results
N°3: How to harmonize a protection schedule ?

26. 26
Schneider Electric 51
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to see all the protections ?
N°3: How to harmonize a protection schedule ?
Schneider Electric 52
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to see all the protections ?
N°3: How to harmonize a protection schedule ?

27. 27
Schneider Electric 53
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to move a column ?
N°3: How to harmonize a protection schedule ?
Harmonize : Micrologic 5..E
Schneider Electric 54
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to move a column ?
N°3: How to harmonize a protection schedule ?
Harmonize : Micrologic 5..E

28. 28
Schneider Electric 55
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to select another Micrologic ?
N°3: How to harmonize a protection schedule ?
Schneider Electric 56
- Customer Software– Ecodial 4 – Training (C) - 2013
●Harmonize all Micrologic Micrologic ?
N°3: How to harmonize a protection schedule ?

29. 29
Schneider Electric 57
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 - Creation
●B) Mars 2011- Vérification et 1ère phase d’harmonisation
●C) March 2012 - Updating
Schneider Electric 58
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to move a column ?
N°3: How to harmonize a protection schedule ?
Harmonize : Micrologic 5..E

30. 30
Schneider Electric 59
- Customer Software– Ecodial 4 – Training (C) - 2013
Exercice N°3
Ecodial Advance Calculation 4
2013
N°4: How to check the switchboard constraints ?

31. 31
Schneider Electric 61
- Customer Software– Ecodial 4 – Training (C) - 2013
N°4: How to check the switchboard
constraints ?
●Objective
● To be able to …
● Define the range of a switchboard
● Check that the chosen switchboard is compliant with the switchgear
Schneider Electric 62
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● The switchboard properties
● Personalize
● The range of the switchboard
● Check the constraints (Prisma Plus P)
● Check the constraints (Prisma Plus G)
N°4: How to check the switchboard
constraints ?

32. 32
Schneider Electric 63
- Customer Software– Ecodial 4 – Training (C) - 2013
●Select the MLVS
N°4: How to check the switchboard
constraints ?
Schneider Electric 64
- Customer Software– Ecodial 4 – Training (C) - 2013
●Select the MLVS
N°4: How to check the switchboard
constraints ?

33. 33
Schneider Electric 65
- Customer Software– Ecodial 4 – Training (C) - 2013
●Choose the switchboard range
N°4: How to check the switchboard
constraints ?
Schneider Electric 66
- Customer Software– Ecodial 4 – Training (C) - 2013
●Choose the switchboard range
N°4: How to check the switchboard
constraints ?

34. 34
Schneider Electric 67
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check the switchboard constraints (Prima Plus P)
N°4: How to check the switchboard
constraints ?
Schneider Electric 68
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check the switchboard constraints ( Prisma Plus G)
N°4: How to check the switchboard
constraints ?

35. 35
Schneider Electric 69
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011- Vérfification et 1ère phase d’harmonisation
●C) Mars 2012 – Up dating V4.25
Schneider Electric 70
- Customer Software– Ecodial 4 – Training (C) - 2013
Exercice N° 4 switchboard constraints

36. 36
Ecodial Advance Calculation 4
2013
N°5: How to use « operating modes »
Schneider Electric 72
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective
● To be able to …
● Visualise the different operating modes
● Personalize a new operating mode
● Apply it to the project
N°5: How to use operating modes (Normal/Emergency)

37. 37
Schneider Electric 73
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● the single line diagram in « Normal » mode
● Personalize
● Create a new operating mode « Emergency »
● Use the function « management of operating modes »
● Copy the « Normal » mode
● Rename the operating mode mode (Emergency + comment)
● Apply
● Define the « Emergency » mode
● Result
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 74
- Customer Software– Ecodial 4 – Training (C) - 2013
●Single line diagram « Normal » operating mode
N°5: How to use operating modes (Normal/Emergency)

38. 38
Schneider Electric 75
- Customer Software– Ecodial 4 – Training (C) - 2013
●Create a new operating mode « Emergency »
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 76
- Customer Software– Ecodial 4 – Training (C) - 2013
●Create a new operating mode « Emergency »
N°5: How to use operating modes (Normal/Emergency)

39. 39
Schneider Electric 77
- Customer Software– Ecodial 4 – Training (C) - 2013
●Copy the « Normal » operating mode
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 78
- Customer Software– Ecodial 4 – Training (C) - 2013
●Rename the new operating mode (Emergency) + coment
N°5: How to use operating modes (Normal/Emergency)

40. 40
Schneider Electric 79
- Customer Software– Ecodial 4 – Training (C) - 2013
●Define the new operating mode (Emergency)
N°5: How to use operating modes (Normal/Emergency)
Critical loads
Non critical loads
Schneider Electric 80
- Customer Software– Ecodial 4 – Training (C) - 2013
●Define the new operating mode (Emergency)
N°5: How to use operating modes (Normal/Emergency)
Critical loads
Non critical loads

41. 41
Schneider Electric 81
- Customer Software– Ecodial 4 – Training (C) - 2013
●Define the new operating mode (Emergency)
N°5: How to use operating modes (Normal/Emergency)
Critical loads
Non critical loads
Schneider Electric 82
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check the result (Normal mode)
N°5: How to use operating modes (Normal/Emergency)

42. 42
Schneider Electric 83
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check the result
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 84
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check the result (Emergency mode)
N°5: How to use operating modes (Normal/Emergency)

43. 43
Schneider Electric 85
- Customer Software– Ecodial 4 – Training (C) - 2013
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 86
- Customer Software– Ecodial 4 – Training (C) - 2013
N°5: How to use operating modes (Normal/Emergency)

44. 44
Schneider Electric 87
- Customer Software– Ecodial 4 – Training (C) - 2013
N°5: How to use operating modes (Normal/Emergency)
Schneider Electric 88
- Customer Software– Ecodial 4 – Training (C) - 2013
N°5: How to use operating modes (Normal/Emergency)

45. 45
Schneider Electric 89
- Customer Software– Ecodial 4 – Training (C) - 2013
N°5: How to use operating modes (Normal/Emergency)
Ii = 3 150 A
Schneider Electric 90
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) March 2012 – Updating V4.25

46. 46
Schneider Electric 91
- Customer Software– Ecodial 4 – Training (C) - 2013
Exercice N°5
operating modes (Normal/Emergency)
Ecodial Advance Calculation 4
2013
N°6: How to use the function « operating
mode »? Ex: Summer / Winter mode

47. 47
Schneider Electric 93
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective
● To be able to …
● Compare on one project two (or more) operating modes
N°6: How to use the function « operating
mode » (Summer / Winter)
Schneider Electric 94
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● the single line diagram in « Normal » operating mode (Parameter)
● Personalize
● Replace the « Normal » operating mode by a « Summer » mode
● Parameter the « Summer » mode
● Create the « Winter » mode
● Parameter the « Winter » mode
● Result
N°6: How to use the function « operating
mode » (Summer / Winter)

48. 48
Schneider Electric 95
- Customer Software– Ecodial 4 – Training (C) - 2013
●Single line diagram in « Normal » operating mode
N°6: How to use the function « operating
mode » (Summer / Winter)
Ks0,9
Ks 1
Ks 1
Ks 1
Schneider Electric 96
- Customer Software– Ecodial 4 – Training (C) - 2013
●Single line diagram in « Normal » operating mode
N°6: How to use the function « operating
mode » (Summer / Winter)
Lights
AC
H
800 KVA

49. 49
Schneider Electric 97
- Customer Software– Ecodial 4 – Training (C) - 2013
●Create a « summer » operating mode
N°6: How to use the function « operating
mode » (Summer / Winter)
Schneider Electric 98
- Customer Software– Ecodial 4 – Training (C) - 2013
N°6: How to use the function « operating
mode » (Summer / Winter)
●Parameter the « summer » operating mode
30 %
100 %
0 %
630 KVA

50. 50
Schneider Electric 99
- Customer Software– Ecodial 4 – Training (C) - 2013
N°6: How to use the function « operating
mode » (Summer / Winter)
●Create the « winter » operating mode
Schneider Electric 100
- Customer Software– Ecodial 4 – Training (C) - 2013
N°6: How to use the function « operating
mode » (Summer / Winter)
●Parameter the « winter » mode
100 %
20 %
100 %
400 KVA

51. 51
Schneider Electric 101
- Customer Software– Ecodial 4 – Training (C) - 2013
●Reminder of « Normal » operating mode
N°6: How to use the function « operating
mode » (Summer / Winter)
800 KVA
Schneider Electric 102
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) March 2012 – Updating V4.25

52. 52
Schneider Electric 103
- Customer Software– Ecodial 4 – Training (C) - 2013
N° 6 Summer / winter
Ks 1
Ks 1
Ks 0,9
Ks 1
Ecodial Advance Calculation 4
2013
N°7: How to customize an Earthing system ?

53. 53
Schneider Electric 105
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective
● To be able to …
● Check the SEA of a project
● Modify the SEA
N°7: Como personalizar um sistema de aterramento
Schneider Electric 106
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Visualise
● The "default" SEA
● Personalize
● Modify the SEA of a "source" circuit
● Parameter TN-C upstream and TN-S downstream
● Change to TN-S QA 3 and QA 4 circuits
● Check all the SEA in the data table
● Check the compatibility of SEA
● Case of "IT" SEA
N°7: Como personalizar um sistema de aterramento

54. 54
Schneider Electric 107
- Customer Software– Ecodial 4 – Training (C) - 2013
●Visualise the “default” SEA
N°7: How to customize an Earthing system ?
Schneider Electric 108
- Customer Software– Ecodial 4 – Training (C) - 2013
●Visualise the "default" SEA
N°7: How to customize an Earthing system ?

55. 55
Schneider Electric 109
- Customer Software– Ecodial 4 – Training (C) - 2013
●Modify the SEA of the “source” circuit
N°7: How to customize an Earthing system ?
Schneider Electric 110
- Customer Software– Ecodial 4 – Training (C) - 2013
●Modify the SEA of the “source” circuit
N°7: How to customize an Earthing system ?

56. 56
Schneider Electric 111
- Customer Software– Ecodial 4 – Training (C) - 2013
●Parameter TN-C upstream and TN-S downstream
TN C
TN S
N°7: How to customize an Earthing system ?
Schneider Electric 112
- Customer Software– Ecodial 4 – Training (C) - 2013
●Parameter TN-C upstream and TN-S downstream
TN C
N°7: How to customize an Earthing system ?

57. 57
Schneider Electric 113
- Customer Software– Ecodial 4 – Training (C) - 2013
●Parameter TN-S on "QA 3" and "QA 4" circuits
N°7: How to customize an Earthing system ?
Schneider Electric 114
- Customer Software– Ecodial 4 – Training (C) - 2013
●Parameter TN-S on “QA 3” and “QA 4” circuits
N°7: How to customize an Earthing system ?

58. 58
Schneider Electric 115
- Customer Software– Ecodial 4 – Training (C) - 2013
●Check all SEA in the data table
N°7: How to customize an Earthing system ?
Schneider Electric 116
- Customer Software– Ecodial 4 – Training (C) - 2013
●Compatibility of SEA
IT
N°7: How to customize an Earthing system ?

59. 59
Schneider Electric 117
- Customer Software– Ecodial 4 – Training (C) - 2013
●Compatibility of SEA
N°7: How to customize an Earthing system ?
Schneider Electric 118
- Customer Software– Ecodial 4 – Training (C) - 2013
●"IT" SEA
TNC
TNS
IT
N°7: How to customize an Earthing system ?

60. 60
Schneider Electric 119
- Customer Software– Ecodial 4 – Training (C) - 2013
●"IT" SEA
TNS
N°7: How to customize an Earthing system ?
Schneider Electric 120
- Customer Software– Ecodial 4 – Training (C) - 2013
●"IT" SEA
N°7: How to customize an Earthing system ?

61. 61
Schneider Electric 121
- Customer Software– Ecodial 4 – Training (C) - 2013
●"IT" SEA
N°7: How to customize an Earthing system ?
Schneider Electric 122
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) March 2012 - Updating

62. 62
Schneider Electric 123
- Customer Software– Ecodial 4 – Training (C) - 2013
N°7: How to customize an Earthing system ?
IT
Ecodial Advance Calculation 4
2013
N°8: How to use voltage drop?

63. 63
Schneider Electric 125
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective
● To be able to …
● Check the voltage drop in cables
● Parameter the voltage drop
● Solve a problem of voltage drop
N°8: How to use voltage drop
Schneider Electric 126
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● What about standards ?
● Cumulated voltage drop and Ecodial
● Parameter voltage drop
● Individual voltage drop cable by cable
● Individual voltage drop for one cable
● Example with long cables
● Modification of the voltage drop of « WD3 » cable
● Résult after calculation
N°8: How to use voltage drop

64. 64
Schneider Electric 127
- Customer Software– Ecodial 4 – Training (C) - 2013
●What about standard
N°8: How to use voltage drop
IEC 364
Without info => 4%Max
NFC 15 100
Lighting => 6% Max
All others => 8% Max
Schneider Electric 128
- Customer Software– Ecodial 4 – Training (C) - 2013
●Cumulated voltage drop and Ecodial4 Intl
N°8: How to use voltage drop
Generic loads
Lighting
Sockets
4 % Max
Motors

65. 65
Schneider Electric 129
- Customer Software– Ecodial 4 – Training (C) - 2013
●Cumulated voltage drop
N°8: How to use voltage drop
Ief = 979 A
Schneider Electric 130
- Customer Software– Ecodial 4 – Training (C) - 2013
●Error
N°8: How to use voltage drop

66. 66
Schneider Electric 131
- Customer Software– Ecodial 4 – Training (C) - 2013
●First solution
N°8: How to use voltage drop
Schneider Electric 132
- Customer Software– Ecodial 4 – Training (C) - 2013
●First solution
N°8: How to use voltage drop
Ief = 1050 A

67. 67
Schneider Electric 133
- Customer Software– Ecodial 4 – Training (C) - 2013
●Second solution
N°8: How to use voltage drop
Schneider Electric 134
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to reach 4%
N°8: How to use voltage drop
3,39 – 1,32 = 2,07 %

68. 68
Schneider Electric 135
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to reach 4%
N°8: How to use voltage drop
Schneider Electric 136
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to reach 4%
N°8: How to use voltage drop

69. 69
Schneider Electric 137
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to reach 4%
N°8: How to use voltage drop
3,09 – 1 = 2,09 %
Schneider Electric 138
- Customer Software– Ecodial 4 – Training (C) - 2013
●Cumulated voltage drop
N°8: How to use voltage drop

70. 70
Schneider Electric 139
- Customer Software– Ecodial 4 – Training (C) - 2013
●How to reach 4%
N°8: How to use voltage drop
2.47 – 0.4= 2,07 %
Schneider Electric 140
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) Mars 2012 – Updating V4.25

71. 71
Schneider Electric 141
- Customer Software– Ecodial 4 – Training (C) - 2013
N° 8 Voltage drop
Project parameter => DeltaU cable = 4%
Ecodial Advance Calculation 4
2013
N°9: How to create an extension in an existing
installation?

72. 72
Schneider Electric 143
- Customer Software– Ecodial 4 – Training (C) - 2013
N°9: How to create an extension
●Objective
● To be able to … (from an existing installation)
●Check by calculation the required modifications for an extension of two
new circuits
Schneider Electric 144
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Assumption
● Locking an existing project
● Extension of 2 new circuits and parameters
● MV/LV Transformer calculation
● Project verification
● New circuit breaker for the source circuit
● Result
N°9: How to create an extension

73. 73
Schneider Electric 145
- Customer Software– Ecodial 4 – Training (C) - 2013
●Assumption
N°9: How to create an extension
Single core cable /PVC/ trefoil
Cable voltage drop = 4%
Schneider Electric 146
- Customer Software– Ecodial 4 – Training (C) - 2013
●Existing = padlocks
N°9: How to create an extension

74. 74
Schneider Electric 147
- Customer Software– Ecodial 4 – Training (C) - 2013
●Existing = padlocks
N°9: How to create an extension
Schneider Electric 148
- Customer Software– Ecodial 4 – Training (C) - 2013
●Existing = padlocks
N°9: How to create an extension

75. 75
Schneider Electric 149
- Customer Software– Ecodial 4 – Training (C) - 2013
●Icon : “ Lock all “
N°9: How to create an extension
Schneider Electric 150
- Customer Software– Ecodial 4 – Training (C) - 2013
●All components are padlocked
N°9: How to create an extension

76. 76
Schneider Electric 151
- Customer Software– Ecodial 4 – Training (C) - 2013
●2 new loads L10 an L11 in UC2
N°9: How to create an extension
80KVA
Cable 20m
80KVA
Cable 30m
Schneider Electric 152
- Customer Software– Ecodial 4 – Training (C) - 2013
●2 new loads L10 an L11 in UC2
N°9: How to create an extension

77. 77
Schneider Electric 153
- Customer Software– Ecodial 4 – Training (C) - 2013
●2 new loads L10 an L11 in UC2
N°9: How to create an extension
140KVA
Cable 20m
140KVA
Cable 30m
Schneider Electric 154
- Customer Software– Ecodial 4 – Training (C) - 2013
●2 new loads L10 an L11 in UC2
N°9: How to create an extension
140KVA
Cable 20m
140KVA
Cable 30m

78. 78
Schneider Electric 155
- Customer Software– Ecodial 4 – Training (C) - 2013
●Unlock the transformer
N°9: How to create an extension
Schneider Electric 156
- Customer Software– Ecodial 4 – Training (C) - 2013
●Error in QA 0
N°9: How to create an extension

79. 79
Schneider Electric 157
- Customer Software– Ecodial 4 – Training (C) - 2013
●Unlock QA 0
N°9: How to create an extension
Schneider Electric 158
- Customer Software– Ecodial 4 – Training (C) - 2013
●Unlock cable WD 0
N°9: How to create an extension

80. 80
Schneider Electric 159
- Customer Software– Ecodial 4 – Training (C) - 2013
●Unlock QA 9
N°9: How to create an extension
Schneider Electric 160
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Fevrier 2011 – Creation
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) Mars 2012 – Updating V4.25

81. 81
Schneider Electric 161
- Customer Software– Ecodial 4 – Training (C) - 2013
Ex N°9
Cable voltage drop = 4%
create an extension
Schneider Electric 162
- Customer Software– Ecodial 4 – Training (C) - 2013
Ex N°9 create an extension
Single core cable /PVC/ trefoil
Cable voltage drop = 4%

82. 82
Ecodial Advance Calculation 4
October 2012
N°10: How to size cables with harmonic current
in the neutral?
Schneider Electric 164
- Customer Software– Ecodial 4 – Training (C) - 2013
●Objective
● To be able to …
● Visualize and parameter the harmonic distortion in the neutral
conductor of cables
● Calculate the cables and the circuit breaker with harmonic distortion in
the neutral conductor of cables
N°10 How to size cables with harmonic
current in the neutral

83. 83
Schneider Electric 165
- Customer Software– Ecodial 4 – Training (C) - 2013
●The steps:
● Assumptions
● Calculation of a project WITHOUT harmonics
● Parameter a non-linear load
● Case of a medium polluted network
● Results
N°10 How to size cables with harmonic
current in the neutral
Schneider Electric 166
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
Single core cable

84. 84
Schneider Electric 167
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
150mm²
70² 35² 25²
THDI = 0 %
● CSA calculation (THDI = 0%)
Schneider Electric 168
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
Ib 429A
217A
144A 116A
● Calculation of Ib (THDI = 0 %)

85. 85
Schneider Electric 169
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
42 %
● Level of harmonics polution (IEC 60 364)
Schneider Electric 170
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
4P3d+Ns
Ph 70²
N 150²
Ph 35²
N 70² 42 %
● Calculation with THDI 42% in circuits 7, 8 and 9

86. 86
Schneider Electric 171
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
42 %
● Harmonic level in cable N°3
Schneider Electric 172
- Customer Software– Ecodial 4 – Training (C) - 2013
N°10 How to size cables with harmonic current
17,9 %
● Harmonic level in cable N°0

87. 87
Schneider Electric 173
- Customer Software– Ecodial 4 – Training (C) - 2013
Modifications
●A) Février 2011 – Creation
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) Mars 2012 – Updating V4.25
Schneider Electric 174
- Customer Software– Ecodial 4 – Training (C) - 2013
42 %
Single core cable
Ex N° 10 - THDI

88. 88
Ecodial Advance Calculation 4
2013
N°11: How to use operation mode function
“parallel MV/LV transformer”?
Schneider Electric 176
- Customer Software– Ecodial 4 – Training (B) - 2013
●Objective
● To be able to …
● Connect parallel transformer or generator
● Create different operating modes
● Personalize a new operating mode
● Apply it to the project
N°11: How to use the operating mode
function “parallel MV/LV transformer”

89. 89
Schneider Electric 177
- Customer Software– Ecodial 4 – Training (B) - 2013
●The steps:
● Visualise
●The single line diagram in « normal » mode
●The single line diagram in « generator » mode
● Personalize
● Connect a MV/LV transformer in parallel to TA 2
● Use the function « management of operating modes »
● Create a « degraded » mode with one transfo only on each MLVS
● Apply
● Define the « Backup » mode
● Result
N°11: How to use the operating mode
function “parallel MV/LV transformer”
Schneider Electric 178
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram « Normal » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”

90. 90
Schneider Electric 179
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « Normal » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”
Schneider Electric 180
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « Normal » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”

91. 91
Schneider Electric 181
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « Normal » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”
Schneider Electric 182
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « Normal » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”

92. 92
Schneider Electric 183
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « 1 transfo only » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”
Schneider Electric 184
- Customer Software– Ecodial 4 – Training (B) - 2013
●Single line diagram in « 1 transfo only » operating mode
N°11: How to use the operating mode
function “parallel MV/LV transformer”

93. 93
Schneider Electric 185
- Customer Software– Ecodial 4 – Training (B) - 2013
N°11: operating mode parallel transformer
Schneider Electric 186
- Customer Software– Ecodial 4 – Training (B) - 2013
N°11:
operating
mode
parallel
transformer
(1/2)

94. 94
Schneider Electric 187
- Customer Software– Ecodial 4 – Training (B) - 2013
N°11:
operating
mode
parallel
transformer
(2/2)
Schneider Electric 188
- Customer Software– Ecodial 4 – Training (B) - 2013
Modifications
●A) Février 2011 – Création
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation

95. 95
Ecodial Advance Calculation 4
December 2013
N°12: How to set Medium Voltage protection
Schneider Electric 190
- Customer Software– Ecodial 4 – Training - 2013
●Objective
● To be able to …
●
N°12 How to set Medium Voltage protection ?

96. 96
Schneider Electric 191
- Customer Software– Ecodial 4 – Training - 2013
●The steps:
N°12 How to set Medium Voltage protection ?
Schneider Electric 192
- Customer Software– Ecodial 4 – Training - 2013
N°12 How to set Medium Voltage protection ?
Undefined

97. 97
Schneider Electric 193
- Customer Software– Ecodial 4 – Training - 2013
● Choosing Fuse or Relay !
N°12 How to set Medium Voltage protection ?
Schneider Electric 194
- Customer Software– Ecodial 4 – Training - 2013
● Fuse calculation :
N°12 How to set Medium Voltage protection ?

98. 98
Schneider Electric 195
- Customer Software– Ecodial 4 – Training - 2013
● Fuse curve :
N°12 How to set Medium Voltage protection ?
Schneider Electric 196
- Customer Software– Ecodial 4 – Training - 2013
● Fuse curve / Discrimination
N°12 How to set Medium Voltage protection ?

99. 99
Schneider Electric 197
- Customer Software– Ecodial 4 – Training - 2013
● RELAY :
N°12 How to set Medium Voltage protection ?
Generic : Sepam
or equivalent
Schneider Electric 198
- Customer Software– Ecodial 4 – Training - 2013
●Relay : Sepam type or equivalent
N°12 How to set Medium Voltage protection ?

100. 100
Schneider Electric 199
- Customer Software– Ecodial 4 – Training - 2013
● Relay “generic” calculation :
N°12 How to set Medium Voltage protection ?
Schneider Electric 200
- Customer Software– Ecodial 4 – Training - 2013
● Relay “generic” curves :
N°12 How to set Medium Voltage protection ?

101. 101
Schneider Electric 201
- Customer Software– Ecodial 4 – Training - 2013
● RELAY :
N°12 How to set Medium Voltage protection ?
Schneider Electric 202
- Customer Software– Ecodial 4 – Training - 2013
● Relay “Self powered” calculation :
N°12 How to set Medium Voltage protection ?

102. 102
Schneider Electric 203
- Customer Software– Ecodial 4 – Training - 2013
● Relay “Self powered” curves :
N°12 How to set Medium Voltage protection ?
Schneider Electric 204
- Customer Software– Ecodial 4 – Training - 2013
● Relay “Self powered” curves :
N°12 How to set Medium Voltage protection ?

103. 103
Schneider Electric 205
- Customer Software– Ecodial 4 – Training - 2013
Modifications
●A) Février 2011 – Creation
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) Mars 2012 – Updating V4.25
Schneider Electric 206
- Customer Software– Ecodial 4 – Training - 2013
●Relay : Sepam type or equivalent
N°12 How to set Medium Voltage protection ?

104. 104
Ecodial Advance Calculation 4
December 2013
N°12: How to use UPS ?
Schneider Electric 208
- Customer Software– Ecodial 4 – Training - 2013
●Objective
● To be able to …
●
N°12 How to set Medium Voltage protection ?

105. 105
Schneider Electric 209
- Customer Software– Ecodial 4 – Training - 2013
●The steps:
N°13 How to use UPS ?
Schneider Electric 210
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
UPS
2 loads of 10A

106. 106
Schneider Electric 211
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
UPS
2 loads of 10A
Schneider Electric 212
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● UPS properties

107. 107
Schneider Electric 213
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● UPS solution
Schneider Electric 214
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● Solution with 2 loads of 40 A :

108. 108
Schneider Electric 215
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● Solution with 2 loads of 40A :
Schneider Electric 216
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● Solution with 2 loads of 40A / Normal mode

109. 109
Schneider Electric 217
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
● Solution with 2 loads of 40A / Creation of “ Bypass mode “
Schneider Electric 218
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS : Bypass mode

110. 110
Schneider Electric 219
- Customer Software– Ecodial 4 – Training - 2013
Modifications
●A) Février 2011 – Creation
●B) Mars 2011 – Vérification et 1ère phase d’harmonisation
●C) Mars 2012 – Updating V4.25
●D) December 2013 – Updating V4-4
Schneider Electric 220
- Customer Software– Ecodial 4 – Training - 2013
N°13 How to use UPS ?
2 loads of 10A
UPS