Respiratory protection masks must be cleaned and reprocessed expertly. This is not only a matter of hygiene but also of correct application and the lowest possible wear in materials. Our presentation shows how Dräger can support you in this.

1. Cleaning and disinfecting full-face masks
Procedures and specifications (machine and manual)
D-30514-2009

2. WHY CARING FOR YOUR MASK IS IMPORTANT
The full-face mask supplies breathing air and protects the wearer’s
face and eyes against aggressive media. To maintain these functions,
correct cleaning and disinfection (washing) and proper handling are
essential. This alone prevents application errors and counteracts
excessive material wear.
WHY YOU SHOULD TAKE A CLOSE LOOK
Apparent small details can make a big difference. Please read ‒
the information on preparation carefully and pay good attention ‒
to details:
‒‒ Temperature specifications
‒‒ Concentration
‒‒ Soak time etc.
WHICH PRODUCTS WILL BE USED FOR RECONDITIONING
On the following pages, you will find explanations for manual and
machine cleaning and disinfection of full-face masks using the
following detergents:
‒‒ Incidin® Rapid
‒‒ Sekusept® Cleaner
‒‒ Eltra®
‒‒ Sekumatic® FDR
WHEN AND HOW TO CLEAN AND DISINFECT CORRECTLY
To let you know at a glance what is important and when, we have
prepared a graphic representation of the different cleaning and
disinfection phases for you.
We provide
clarity!
ST-7316-2008

3. of full-face masks
Machine reconditioning
PREPARATION & IMPORTANT INFORMATION
Drum-type washing machine
‒‒ Remove accessories, exhalation valve and inner mask.
‒‒ The masks must be placed in the washing bag packed and sealed.
‒‒ Secure helmet adapters, if applicable, or use a suitable washing bag.
Dishwasher/cleaning and disinfection device
‒‒ Remove accessories, exhalation valve and inner mask
and place them in the rinse basket, if applicable.
20 min
Temp. max. 60 °C
20 min
Temp. max. 60 °C
simplified representation
Tumbling washing machine
max. 50 rpm
Liquor ration 1:5*
Cleaning and disinfection device
Dishwasher
Drying
Temp. max. 60 °C
Drying
Temp. max. 60 °C
Drying
Temp. max. 60 °C
5 min
Temp. 60 °C
5 min 30 sec
Temp. 60 °C
5 min
Temp. 60 °C
30 sec
Temp.
max. 60 °C
5 min
Temp. max. 60 °C
Drying
Temp. max. 60 °C
20 min
Temp. 60 °C
6 cycles à 3 min
20 ±5 °C
6 cycles à 3 min
20 ±5 °C
Eltra®
All-purpose disinfectant
Concentration 5 g/l
Sekumatic® FDR
Detergent and disinfectant
Concentration 10 ml/l
Sekumatic® FDR
Detergent and disinfectant
Concentration 10 ml/l
Sekumatic® FDR
Detergent and disinfectant
Concentration 10 ml/l
Moment of addition
Phase 2
Cleaning and
disinfection
Phase 3
Rinsing
Phase 4
Drying
Phase 1
Warm-up and
pre-cleaning
*Liquor ratio = drum capacity : [water volume – (number of masks × 0,5 l) – detergent]

4. PREPARATION & IMPORTANT INFORMATION
‒‒ Remove accessories, exhalation valve and inner mask.
‒‒ No residue of skin care products must remain on the mask ‒
after thorough cleaning.
‒‒ Do not use solvents, such as acetone or alcohol, or detergents
with abrasive particles for cleaning.
‒‒ Facepieces with a visor marked with PCaf or PC/CC must not
be cleaned or dried using a cloth, because the coating may be
damaged. After drying, the facepieces should be aired without
being packed for at least one day at standard atmospheric ‒
conditions (DIN EN ISO 291).
of full-face masks
Manual reconditioning
simplified representation
DryingIncidin® RapidSekusept® Cleaner
Phase 5
Drying
Temp. max. 60 °C
Phase 4
Rinsing
Phase 3
Disinfection
Concentration: 1,5 %
Temperature: max. 30 °C
Duration: 15 min
Phase 2
Rinsing
Phase 1
Cleaning
Concentration: 0,5 – 1 %
Temperature: max. 30 °C

5. BEFORE AND DURING CLEANING
‒‒ Adherence to the washing parameters (dosage, soak time etc.) ‒
must be ensured.
‒‒ The Instructions for Use of the mask, the machine and the ‒
detergent (incl. dosage table) must be strictly adhered to.
‒‒ Washing machines should be serviced regularly.
‒‒ Washing bags should be replaced if heavily worn or damaged.
‒‒ The washing drum must always be fully loaded. If necessary, ‒
you can also wash dummy masks.
‒‒ Masks should be packed in dry bags when using a tumble dryer.
‒‒ Some mask versions are excluded from approval for machine
reconditioning; detailed information can be found in the
respective washing instructions from Dräger.
AFTER CLEANING
‒‒ After the washing and drying process, the masks must be
subjected to a visual, leak and functional inspection.
General
information

6. Incidin® Rapid, Sekusept® Cleaner, Eltra® and Sekumatic® FDR are registered trademarks of ECOLAB.
REGION EUROPE CENTRAL
AND EUROPE NORTH
Dräger Safety AG & Co. KGaA ‒
Revalstraße 1
23560 Lübeck, Germany
Tel +49 451 882 0
Fax +49 451 882 2080
info@draeger.com‒
REGION EUROPE SOUTH
Dräger Safety France SAS
25, rue Georges Besse
92182 Antony Cedex
Tel +33 1 46 11 56 00
Fax +33 1 40 96 97 20
europe.south@draeger.com
REGION MIDDLE EAST, AFRICA
Dräger Safety AG & Co. KGaA
Branch Office ‒
P.O. Box 505108 ‒
Dubai, United Arab Emirates
Tel +971 4 4294 600
Fax +971 4 4294 699
contactuae@draeger.com
REGION ASIA PACIFIC
Draeger Safety Asia Pte Ltd
25 International Business Park
#04-20/21 German Centre
Singapore 609916
Tel +65 6308 9400
Fax +65 6308 9401
asia.pacific@draeger.com
REGION CENTRAL
CORPORATE HEADQUARTERS
Drägerwerk AG & Co. KGaA
Moislinger Allee 53–55
23558 Lübeck, Germany
www.draeger.com
Manufacturer:
Dräger Safety AG & Co. KGaA
Revalstraße 1
23560 Lübeck, Germany
AND SOUTH AMERICA
Dräger Panama S. de R.L.
Complejo Business Park, ‒
V tower, 10th floor
Panama City
Tel +507 377-9100
Fax +507 377-9130
contactcsa@draeger.com
Locate your Regional Sales
Representative at:
www.draeger.com/contact
9072102|15.07-2|Communications&SalesMarketing|PP|LE|©2015DrägerwerkAG&Co.KGaA