This document provides safety guidelines for maintaining forklifts. It outlines 18 safety practices including properly ventilating work areas, disconnecting batteries before electrical work, checking for fuel leaks, using lifting equipment rated for the load, and only allowing trained personnel to perform maintenance. Special terms like Warning, Danger and Caution are defined for identifying hazard levels.
Clark cmp18 forklift service repair manualfjkskefksmeme
This document provides safety guidelines for maintaining forklifts. Some key points include:
- Only trained personnel should perform maintenance. Proper ventilation, fire protection and truck positioning is required.
- Inspect brakes, steering, controls and other components regularly. Make no modifications without approval.
- Use genuine replacement parts equal to or better than original equipment. Take care when removing heavy components.
- Address any fuel leaks immediately and do not operate the forklift until repaired. Refer to relevant safety standards for additional guidance.
The document provides instructions and safety guidelines for maintaining Clark industrial trucks. It outlines important safety practices such as properly blocking the truck, disconnecting the battery before working on electrical systems, checking for fuel leaks, and only performing maintenance authorized by Clark. The document is intended to help service personnel safely maintain trucks in accordance with manufacturer specifications.
Clark cdp 20 30 forklift service repair manualfjjsieskekfmmse
This document provides a copyrighted shop manual for Clark dealers intended for service of Clark truck models. It contains instructions for safe maintenance practices and lifting, jacking, and blocking the truck. The manual consists of base modules that apply to all Genesis models and additional modules specific to individual truck models.
Clark cmp 50 forklift service repair manualfjsqazkekdmme
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising the drive wheels, front of the truck, and entire truck using an upright or hoist. Blocking methods are outlined to secure the truck in its raised position.
Clark cmp20 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp18 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp15 forklift service repair manualfjksekmdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp18 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp18 forklift service repair manualfjkskefksmeme
This document provides safety guidelines for maintaining forklifts. Some key points include:
- Only trained personnel should perform maintenance. Proper ventilation, fire protection and truck positioning is required.
- Inspect brakes, steering, controls and other components regularly. Make no modifications without approval.
- Use genuine replacement parts equal to or better than original equipment. Take care when removing heavy components.
- Address any fuel leaks immediately and do not operate the forklift until repaired. Refer to relevant safety standards for additional guidance.
The document provides instructions and safety guidelines for maintaining Clark industrial trucks. It outlines important safety practices such as properly blocking the truck, disconnecting the battery before working on electrical systems, checking for fuel leaks, and only performing maintenance authorized by Clark. The document is intended to help service personnel safely maintain trucks in accordance with manufacturer specifications.
Clark cdp 20 30 forklift service repair manualfjjsieskekfmmse
This document provides a copyrighted shop manual for Clark dealers intended for service of Clark truck models. It contains instructions for safe maintenance practices and lifting, jacking, and blocking the truck. The manual consists of base modules that apply to all Genesis models and additional modules specific to individual truck models.
Clark cmp 50 forklift service repair manualfjsqazkekdmme
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising the drive wheels, front of the truck, and entire truck using an upright or hoist. Blocking methods are outlined to secure the truck in its raised position.
Clark cmp20 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp18 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp15 forklift service repair manualfjksekmdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp18 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp30 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp30 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp20 forklift service repair manualdikdkskdmmd
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp25 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire truck with a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp15 forklift service repair manualfjjsekkdmme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working underneath, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp20 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front of the truck, and rear of the truck. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or bracing parts to prevent instability and tipping hazards.
Clark cmp15 forklift service repair manualdidkkskdmmd1
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp30 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp18 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp25 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp25 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp 50 s forklift service repair manualfjjsieskekfmmse
This document provides instructions for safely maintaining a Clark Model CMP 40/45/50S forklift. It begins with general safety practices and identifies hazards using warning symbols. Sections provide procedures for lifting, jacking, and blocking the forklift, including approved lifting points. Technicians are instructed to raise wheels off the floor using the upright as a lever before working underneath. The document emphasizes checking equipment capacity ratings and stabilizing the forklift during maintenance.
This document provides instructions for safely maintaining a Clark forklift. It discusses arranging and using the service manual, as well as safety practices like properly lifting, jacking, and blocking the forklift. Specific instructions are provided for raising different parts of the forklift, including the drive wheels, entire forklift with a hoist, and blocking the upright in a raised position. Workers are instructed to only perform maintenance after reviewing all safety procedures and using properly rated equipment.
Clark CMP 50S Forklift Service Repair Manual.pdfshun96145luo
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Clark CMP 40 Forklift Service Repair Manual.pdff7useijdkdmd1
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 40 Forklift Service Repair Manual.pdfdxem8295569
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Clark CMP 50S Forklift Service Repair Manual.pdfdxem8295569
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended to support lifted parts. Safety practices are emphasized, such as checking equipment capacity and stability during lifting.
Clark CMP 45 Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 50S Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 45 Forklift Service Repair Manual.pdfshun96145luo
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Same frutteto³ s 90 tractor service repair manual (sn 1001 and up)fjkskefksmeme
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
Caterpillar cat 385 c l excavator (prefix jcm) service repair manual (jcm0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
More Related Content
Similar to Clark cmp25 forklift service repair manual
Clark cmp30 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp30 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp20 forklift service repair manualdikdkskdmmd
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp25 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire truck with a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp15 forklift service repair manualfjjsekkdmme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working underneath, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp20 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front of the truck, and rear of the truck. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or bracing parts to prevent instability and tipping hazards.
Clark cmp15 forklift service repair manualdidkkskdmmd1
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp30 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using lifting equipment with sufficient capacity and blocking or stabilizing parts of the truck during maintenance.
Clark cmp18 forklift service repair manualdikdkskdmmd
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp25 forklift service repair manualjdfjskekmdme
This document provides safety guidelines for maintaining powered industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting batteries, checking for fuel leaks, and using genuine replacement parts. The guidelines aim to prevent injuries from hazards that could arise during maintenance through proper precautions, training, ventilation, fire safety, and following manufacturer specifications.
Clark cmp25 forklift service repair manualfdhjsekdme
This document provides instructions for safely lifting, jacking, and blocking a forklift truck. It identifies approved lifting points on the truck and describes procedures for raising different parts of the truck, including the drive wheels, entire front end using a hoist, and upright assembly. Safety precautions are emphasized, such as using equipment with sufficient lifting capacity and blocking or supporting components to prevent tipping.
Clark cmp 50 s forklift service repair manualfjjsieskekfmmse
This document provides instructions for safely maintaining a Clark Model CMP 40/45/50S forklift. It begins with general safety practices and identifies hazards using warning symbols. Sections provide procedures for lifting, jacking, and blocking the forklift, including approved lifting points. Technicians are instructed to raise wheels off the floor using the upright as a lever before working underneath. The document emphasizes checking equipment capacity ratings and stabilizing the forklift during maintenance.
This document provides instructions for safely maintaining a Clark forklift. It discusses arranging and using the service manual, as well as safety practices like properly lifting, jacking, and blocking the forklift. Specific instructions are provided for raising different parts of the forklift, including the drive wheels, entire forklift with a hoist, and blocking the upright in a raised position. Workers are instructed to only perform maintenance after reviewing all safety procedures and using properly rated equipment.
Clark CMP 50S Forklift Service Repair Manual.pdfshun96145luo
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Clark CMP 40 Forklift Service Repair Manual.pdff7useijdkdmd1
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 40 Forklift Service Repair Manual.pdfdxem8295569
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Clark CMP 50S Forklift Service Repair Manual.pdfdxem8295569
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended to support lifted parts. Safety practices are emphasized, such as checking equipment capacity and stability during lifting.
Clark CMP 45 Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 50S Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 45 Forklift Service Repair Manual.pdfshun96145luo
This document provides instructions for safely lifting, jacking, and blocking a Clark forklift truck. It describes approved lifting points on the truck and procedures for raising different parts, including the drive wheels, entire front, and rear. Blocking is recommended whenever raising parts to prevent accidental rolling or movement. Safety practices like parking on level ground, engaging brakes, and removing keys are advised before beginning any work.
Similar to Clark cmp25 forklift service repair manual (20)
Same frutteto³ s 90 tractor service repair manual (sn 1001 and up)fjkskefksmeme
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
Caterpillar cat 385 c l excavator (prefix jcm) service repair manual (jcm0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...fjkskefksmeme
This document provides instructions for removing and installing various components of a Caterpillar C-18 diesel engine, including:
1. Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
2. Installing the variable valve actuator by reinstalling mounting hardware and reconnecting harnesses.
3. Removing the rocker arm assembly by removing mounting bolts and using a lifting bracket.
4. Disassembling the rocker arm by removing adjustment screws, buttons, seals, and arms from the rocker shaft.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...fjkskefksmeme
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Diagrams and specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and lubricated during disassembly and reassembly.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 385 c excavator (prefix kbc) service repair manual (kbc00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the travel motor of a 385C Excavator. It lists 40 steps for disassembly, including removing the head, relief valves, port plate, piston, swashplate, shaft, and seals. It also lists 12 steps for assembly, starting with installing the lip seal in the housing and ending by applying a light film of oil to all components before final assembly. Precision tools are required and cleanliness is important to prevent contamination.
Caterpillar cat 385 c excavator (prefix jcm) service repair manual (jcm00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 385 b l excavator (prefix rcd) service repair manual (rcd0000...fjkskefksmeme
The document provides instructions for disassembling and assembling various components of an excavator control valve, including:
1. Disassembling the proportional valve by removing bolts, nuts, and cartridge components.
2. Assembling the attachment, bucket, and boom control valve by installing O-rings, plugs, resolver valves, springs, and actuator groups.
3. Assembling the right travel, left travel, and stick control valve by installing spools, plugs, resolver valves, and O-rings. Detailed steps and illustrations are provided for each disassembly and assembly procedure.
Caterpillar cat 385 b l excavator (prefix fdl) service repair manual (fdl0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly process involves removing 27 parts from the final drive housing including gears, shafts, seals and bearings. Tools and lifting devices are required to remove some heavy components weighing up to 340 pounds.
The assembly process reverses the disassembly steps and provides details on installing seals, bearings and shims to achieve proper bearing preload. Precise measurement and calculation are involved to determine the correct shim thickness. Lubricants and cleaning procedures are also specified.
Yamaha outboard f50 feht service repair manual sn1000001fjkskefksmeme
This document provides a service manual for outboard motor models F50F, FT50G, F60C, and FT60D. It contains general information about how to use the manual, identification of applicable models and features, predelivery checks, and troubleshooting guides. The manual is organized into sections covering general information, specifications, periodic checks and adjustments, fuel system, power unit, lower unit, bracket unit, electrical systems, and troubleshooting. It also includes exploded diagrams of components and lists parts with quantities and specifications.
Yale b974 gdp50 lx lift truck service repair manualfjkskefksmeme
This document provides service information for a GLP060LX or GDP50LX lift truck. It contains:
1. A table of contents listing the sections and part numbers for the service manual.
2. A general warning about safety procedures when putting the lift truck on blocks for maintenance.
3. Instructions for removing and installing the hood, seat, and side covers of the lift truck, including disconnecting wiring harnesses and removing fasteners.
Yale (e877) gdp130 ec lift truck service repair manualfjkskefksmeme
The document provides instructions for raising and lowering the operator cab on a lift truck, as well as removing and installing the cab door. Key steps include:
1. Using the cab tilt hand pump or electric pump to raise or lower the cab until it locks in position.
2. Pulling the tilt latch release to fully raise or lower the cab.
3. Attaching lift straps and cushions to safely remove the cab door from its hinges and place it on the ground.
4. Reinstalling the cab door by lifting it back into position on the hinges and adjusting if needed.
Perkins peregrine edi and 1300 series edi ws diesel engine service repair manualfjkskefksmeme
This document is a workshop manual for Perkins Peregrine EDi and 1300 Series EDi diesel engines. It provides information on servicing various engine components including the cylinder head, pistons, connecting rods, crankshaft, timing case, and related systems. The manual contains detailed instructions for removal, inspection, repair and installation of engine parts, with torque specifications and safety precautions. It is intended as a guide for technicians servicing these Perkins diesel engines.
Perkins peregrine edi and 1300 series edi wq diesel engine service repair manualfjkskefksmeme
This document is a workshop manual for Perkins Peregrine EDi and 1300 Series EDi diesel engines. It provides information on servicing and repairing engine components. The manual contains chapters covering the cylinder head assembly, piston and connecting rod assemblies, crankshaft assembly, timing case and drive assembly, and other systems. It includes detailed instructions for removing, inspecting, and installing components with torque specifications. The document is intended as a reference for technicians servicing these Perkins diesel engines.
Perkins 2800 series 2806 c e16 diesel engine service repair manualfjkskefksmeme
This document provides maintenance and repair instructions for a Perkins 2800 Series 6-cylinder turbocharged diesel engine. It contains specifications, procedures for disassembling and assembling various engine components, such as the cylinder head, pistons, crankshaft, and timing gears. Safety precautions and environmental protection guidelines are also outlined. The manual is intended to assist technicians in servicing and repairing these industrial diesel engines.
Perkins 2000 series 2006 diesel engine(model 2006 twg2)service repair manualfjkskefksmeme
This document provides instructions for servicing and repairing Perkins 2000 Series 6-cylinder diesel engines. It details procedures for removing and installing major engine components like the cylinder head, pistons, crankshaft, and fuel system parts. Safety precautions are also outlined regarding working on diesel engines, as well as specifications for torque values and recommended clearances between parts.
Perkins 1300 series we diesel engine service repair manualfjkskefksmeme
This document is a workshop manual that provides specifications, repair and maintenance instructions for Perkins Peregrine and New Generation 1300 Series diesel engines. It contains chapters covering the cylinder head assembly, piston and connecting rod assemblies, crankshaft assembly, timing case and drive assembly, and other systems. The manual includes detailed parts lists, diagrams, specifications, and recommended torque settings to guide technicians in servicing and repairing engine components.
Kubota g21 ld tractor mower service repair manualfjkskefksmeme
This document provides maintenance information for a workshop manual, including:
- Identification of engine and machine serial numbers, hour meter, etc.
- General precautions for handling parts, wiring, batteries, and using proper lubricants.
- Tightening torques for screws, bolts and nuts in metric and imperial units.
- Maintenance checklists and inspection schedules for daily, 50 hour, 100 hour, yearly and other periodic checks.
- Lists of special tools required for engine and machine maintenance and repair.
- Limitations on implement usage.
The document outlines identification, safety, inspection and maintenance procedures for workshop personnel servicing this equipment.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Arrangement and Use of this Manual
Clark arranges parts and service procedures by standard-
ized Groups. In this manual, Groups are similar to “chap-
ters.” Groups are listed in the table of contents on the next
page.
You can quickly locate a specific point in the manual by
using the headers and footers that appear on the pages. The
following illustration points out these areas.
Each Group begins with a table of contents that shows the
Sections contained within the Group. Lengthy Sections
also begin with a table of contents showing the topics
contained within the Section.
Each Group and Section has an identifying name and
number, or “ID.”
Each page also has a unique ID. The page ID consists of
three numbers separated by hyphens. The three numbers
represent the Group number, the Section number, and the
page number. For example, “00-1-2” on the lower comer
of the page indicates Group 00, Section 1, Page 2. This manual is intended for the use of trained service
personnel. Please read Group SA, “Safe Maintenance,”
and the Operator’s Manual before working on or operat-
ing the truck.
0 Copyright Clark Material Handling Company 1998 SM 638,Oct ‘98
3. CONTENTS
Contents
Contents are listed by Group number and name followed by Section number and name:
SA
PS
00
01
02
06
12
14
SAFE MAINTENANCE
1. Safety
2. Lifting, Jacking, and Blocking
3. Towing
PERIODIC SERVICE
1. Maintenance Schedules
2. Planned Maintenance
3. PM Inspection Form
ENGINE
1. Specifications and Description
2. Troubleshooting
3. Engine Oil
4. Tune-Up
5. RPM, Vacuum, and Stall Checks
6. Compression Checks
7. Removal and Replacement
8. Overhaul
COOLING SYSTEM
1. Specifications and Description
2. Troubleshooting
FUEL SYSTEM
1. LPG Fuel System
2. Gasoline Fuel System
TRANSAXLE
1. Specifications and Description
2. Checks and Troubleshooting
3. Removal and Replacement
3. Overhaul
IGNITION SYSTEM
1. Specifications and Description
2. Troubleshooting
3. Ignition Timing
4. Distributor Overhaul
ELECTRICAL
1. Circuit Diagram
2. Starter
3. Alternator
4. Instrument Pod
16 WHEELS AND TIRES
1. Specifications and Description
2. Cushion Wheels and Tires
3. Pneumatic Wheels and Tires
23 BRAKE SYSTEM
1. Specifications
2. Service Brake
3. Parking Brake
25126 STEER SYSTEM
1. Specifications and Description
2. Troubleshooting
3. Steering System Pressure Check
4. Steering System Removals & Installations
5. Steering Unit Overhaul
6. Priority Valve Overhaul
7. Steer Cylinder Overhaul
29/30 HYDRAULIC SYSTEM
1. Specifications and Description
2. Troubleshooting
3. Hydraulic Pump Overhaual
4. Control Valve Overhaul
34 UPRIGHTS
1. Specifications and Description
2. Upright Checks and Adjustments
3. Lift Chain Service
4. Removals and Replacements
5. Lift and Tilt Cylinder Overhaul
38 COUNTERWEIGHT
1. Specifications
2. Inspection
3. Removal and Replacement
40 SPECIFICATIONS
1. Specifications
SM 638,Oct ‘98 Contents-iii
4. GROUP SA
GROUP SA
SAFE MAINTENANCE
Safety ............................................................................... Section 1
Lifting, Jacking, and Blocking the Truck ..................... Section 2
Towing .............................................................................. Section ‘2
SM 638,Oct ‘98 Safe Maintenance
5. CIRRK Group SA, Safe Maintenance
Section 1. Safety
SafetySigns and Messages Safe Maintenance Practices
Safety signs and messages in this manual and on the lift
truck provide instructions and identify specific areas where
potential hazards exist and special precautions should be
taken. Be sure you know and understand the meaning of
these instructions, signs, and messages. Damage to the
truck, death, or serious injury to you or other persons may
result if these messages are not followed.
NOTE
This message is used when special informa-
tion, instructions or identification is re-
quired relating to procedures, equipment,
tools, pressures, capacities, and other spe-
cial data.
The following instructions have been prepared from cur-
rent industry and government safety standards applicable
to industrial truck operation and maintenance. These rec-
ommended procedures specify conditions, methods, and
accepted practices that aid in the safe maintenance of in-
dustrial trucks. They are listed here for the reference and
safety of all workers during maintenance operations. Care-
fully read and understand these instructions and the spe-
cific maintenance procedures before attempting to do any
repair work.
When in doubt of any maintenance procedure, please con-
tact your local Clark dealer.
1.
IMPORTANT
Powered industrial trucks can become hazardous if
maintenance is neglected. Therefore, suitable mainte-
nance facilities, trained personnel, and procedures
must be provided.
This message is used when special precau-
tions should be taken to ensure a correct
action or to avoid damage to, or malfunc-
tion of, the truck or a component.
2. Maintenance and inspection of all powered industrial
trucks shall be done in conformance with the
manufacturer’s recommendations.
3.
A CAUTION
This message is used as a reminder of safety
hazards that can result in personal injury
if proper precautions are not taken.
A scheduled planned maintenance, lubrication, and
inspection program shall be followed.
4. Only trained and authorized personnel shall be permit-
ted to maintain, repair, adjust, and inspect industrial
trucks. Work should be performed in accordance with
the manufacturer’s specifications.
A WARNING
This message is used when a hazard exists
that can result in injury or death if proper
precautions are not taken.
5. Properly ventilate work area, vent exhaust fumes, and
keep shop clean and floor dry.
6.
A DANGER
This message is used when an extreme haz-
ard exists that can result in injury or death
or serious injury if proper precautions are
not taken.
Avoid fire hazards and have fire protection equipment
present in the work area. Do not use an open flame to
check for level or leakage of fuel, electrolyte, or
coolant. Do not use open pans of fuel or flammable
cleaning fluids for cleaning parts.
7. Before starting work on truck:
The above terms have been adopted by Clark Material
Handling Company. The same terms may be used in differ-
ent context in service literature supplied directly or indi-
rectly by vendors of truck components.
a. Raise drive wheels off of floor or disconnect
power source and use blocks or other positive
truck positioning devices.
b. Disconnect battery before working on the electri-
cal system.
8. Before working on engine fuel system of gasoline- or
diesel-powered trucks, be sure the fuel shut-off valve
is closed.
SM 638,Oct ‘98 Safety l SA-l-l
6. Group SA, Safe Maintenance CWRK
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Operation of the truck to check performance must be
conducted in an authorized, safe, clear area.
Before starting to drive truck:
a. Be in operating position.
b. Be sure parking brake is engaged.
c. Put direction control in neutral.
d. Start engine.
e. Check functioning of direction and speed con-
trols, steering, brakes, warning devices, and any
load handling attachments.
Before leaving truck
a. Stop truck.
b. Put directional control in neutral.
c. Apply the parking brake.
d. Stop the engine by turning off the ignition circuit.
e. Put blocks at the wheels if truck is on an incline.
Brakes, steering mechanisms, control mechanisms,
warning devices, lights, governors, guards, safety de-
vices, and frame members must be carefully and regu-
larly inspected and maintained in a safe operating
condition.
19.
20.
21.
Modifications and additions that affect capacity and
safe truck operation must not be done without the
manufacturer’s prior written approval. Capacity, op-
eration and maintenance instruction plates, tags, or
decals must be changed accordingly. This is an OSHA
requirement.
Care must be taken to assure that all replacement parts,
including tires, are interchangeable with the original
parts and of a quality at least equal to that provided in
the original equipment. Parts, including tires, are to be
installed per the manufacturer’s procedures. Always
use genuine CLARK or CLARK-approved parts.
Use special care when removing heavy components
from the truck, such as counterweight, seat deck,
upright, etc. Be sure that lifting and handling equip-
ment is of the correct capacity and in good condition.
Also, this removal may upset the stability of the truck.
The frame must always be safely blocked for major
component removal.
NOTE
Special trucks or devices designed and approved for
hazardous area operation must receive special atten-
tion to ensure that maintenance preserves the original,
approved, safe-operating features.
You should also be familiar with additional
operating and maintenance safety instruc-
tions contained in the following publica-
tions:
Fuel systems must be checked for leaks and condition
of parts. Extra special consideration must be given in
the case of a leak in the fuel system. Action must be
taken to prevent the use of the truck until the leak has
been corrected.
The truck manufacturer’s capacity, operation, and
maintenance instruction plates, tags, or decals must be
maintained in legible condition.
ANSI/ASME B56.1- 1988 Operator Control-Industrial Tow
Tractors (Safety Standard For Powered Industrial Trucks).
Published by: Society of Mechanical Engineers, United
Engineering Center, 345 E. 47th Street, New York, NY
10017.
NFPA 505-1982: Fire Safety Standard for Powered Indus-
trial Trucks: Type Designations, Areas of Use, Mainte-
nance and Operation. Available from: National Fire
Protection Assoc., Inc., Batterymarch Park, Quincy, MA
02269.
Batteries, motors, controllers, limit switches, protec- General Industrial Standards, OSHA 2206: OSHA Safety
tive devices, electrical conductors, and connections and Health Standards (29 CFR 19lo), Subpart N-Materials
must be inspected and maintained in conformance Handling and Storage, Section 1910.178 Powered Indus-
with good practice. Special attention must be paid to trial Trucks. For sale by: Superintendent of Documents,
the condition of electrical insulation. U.S. Government Printing Office, Washington, DC 20402.
To avoid injury to personnel or damage to the equip-
ment, consult the manufacturer’s procedures inreplac-
ing contacts on any battery connection.
Industrial trucks must be kept in a clean condition to
minimize fire hazards and help in the detection of loose
or defective parts.
SA-1-2 l Safety SM 638,Oct ‘98
7. ElmK Group SA, Safe Maintenance
Section 2.
Lifting, Jacking, and Blocking
Safe Parking ................................................................................................................................... 2
Lifting, Jacking, and Blocking Points .......................................................................................... 2
Raising Drive Wheels Off Floor ................................................................................................... 2
Raising Truck with A Hoist .......................................................................................................... 3
Blocking the Upright in Raised Position ...................................................................................... 4
Raising Rear of Truck ................................................................................................................... 4
Raising Entire Truck ..................................................................................................................... 5
Shipping Tie-Down Instructions ................................................................................................... 6
A WARNING
Lifting or jacking any large piece of equipment such as your fork truck presents
obvious hazards. It must be done with great care and forethought. Consult the
truck weight tabulations in Group 40, “Specifications” to ensure that your
lifting equipment is of adequate capacity.
SM 638,Oct ‘98 Lifting, Jacking, and Blocking l SA-2-1
8. Group SA, Safe Maintenance CICIRU
Safe Parking Raising Drive Wheels Off Floor
Before working on truck:
1.
2.
3.
4.
Park truck on a hard, level, and solid surface, such as
a concrete floor with no gaps or breaks.
Put upright in vertical position and fully lower the
forks or attachment.
This procedure uses the upright as a lever to lift the drive
wheels off the floor and prevent accidents due to inadvert-
ent powering of the drive wheels.
Park truck safely as described in “Safe Parking.” Block
steer wheels.
Put all controls in neutral. Turn key switch OFF and
remove key.
Apply the parking brake and block the wheels.
Be sure upright trunnion bolts are tight. Bolt torques
must be 75-80 Nom (55-59 ft-lb).
Start the engine. Tilt the upright fully back. Adjust
upright height as necessary to put blocking underneath
the lower end of the upright.
Put a solid 100 x 100 mm (4 x 4 in) hardwood block
under the front section of each upright rail. Put a 3-6
mm (.125--250 in) steel plate on top of each block.
A WARNING
Defective equipment can cause accidents.
All tools and lifting equipment must be in
good condition, meet the load capacity re-
quirements and have OSHA labels when
required. Tools with defects can have fail-
ures causing severe injury or death.
Lifting, Blocking, and Jacking Points
Use the following illustration to locate general lifting, block-
ing, and jacking points on the truck. Read the procedures
for raising, blocking, or jacking specific components of the
truck to make sure you understand the correct, safe proce-
dures.
J On Tie Bars
1UnderSteer yUnder Frame L Under Upright
Axle Frame
Mount
A WARNING
Do not attempt to lift the truck by the over-
head guard or the counterweight. Severe
injury may result and the truck can be
damaged.
5. Tilt upright fully forward. This raises the drive wheels
off the floor. Release the tilt control lever and turn
engine OFF.
SA-2-2 l Lifting, Jacking, and Blocking SM 638,Oct ‘98
9. CHIC Group SA, Safe Maintenance
6. Insert blocking under the frame behind the drive
wheels or slip wheel cradles under the drive wheels. If
using blocking, check for safe clearance between drive
wheels and floor and blocks.
3. To raise the front of the truck using the upright, spread
two chains on the outer rail tiebar of the upright.
NOTE
When forks are raised as in illustration
above, use shop rags, paper, or bright tape
on fork tips to signal the danger of trip-
ping.
7. Check for stable condition of the truck. Be sure that the
blocks are located securely under the truck frame
before operating the drive or working on truck.
8. Lower the drive wheels to the floor and remove the
blocks by reversing the above procedure.
Raising Truck with a Hoist
When suitable equipment is available, the front of the truck
may be raised by means of a hoist, with wheel cradles
placed under the wheels or blocking placed under the frame.
1.
2.
A CAUTION
When lifting the front of the truck watch
truck for signs of lateral instability. It may
tip sideways. You may have to support or
guide the side of the truck or overhead
guard to prevent tipping.
Park truck safely as described in“Safe Parking.” Block
rear steer wheels.
Check trunnion bolts to make sure they are tightened to
correct torque. Bolt torques must be 75-80 N*m(55-59
f&lb).
4.
A WARNING
Chain and hoist used to lift truck should be
checked to make sure they are of safe lift-
ing capacity. See the truck data plate for
information.
Slowly lift truck and lower drive wheels onto the
cradles or place blocking under frame prop points.
5. When maintenance work is completed, lower the truck
to the floor by reversing the lifting procedure. Check to
be sure no tools or equipment are under the truck or
wheels.
SM 638,Oct ‘98 Lifting, Jacking, and Blocking l SA-2-3
10. Group SA, Safe Maintenance CMRK
Blocking the Upright In Raised Position
This procedure is used to safely provide clearance for
access from the front of truck to components on or near the
drive axle. Illustrations show upright with forks removed
however, fork removal is not necessary
1.
2.
3.
4.
5.
Park truck safely as described in “Safe Parking.”
Put blocks in front of and behind drive wheels.
Put wooden support blocks conveniently near upright
rails before raising the upright. Use two 100x 100mm
(4x 4 in) hardwood blocks or equal, of about 300 x 300
mm (12 in) and 600 x 600 mm (24 in) length.
NOTE
For standard uprights, block may need
length cut to suit. For triple stage uprights,
the carriage may be blocked up, as shown.
Start engine and raise the upright carriage.
Hold the taller block against inner rail and lower the
upright until carriage rests on block.
Outer
Rail
6. Hold the shorter block against the outer rail and lower
the upright until inner rail rests on the block.
Outer
Rail
7. Reverse the procedure to remove blocking.
Raising Rear of Truck
The truck may be raised at the rear by jacking and blocking
under the center of the frame member at either the front or
rear steer axle mounting, or under the center section of the
steer axle.
Refer to truck data plate for truck weights.
A WARNING
An incorrectly installed counterweight can
move or fall unexpectedly. Never lift or
block a truck using the counterweight. Fail-
ure to follow procedures outlined in this
manual can result in injury or death.
1. Park truck safely as described in “Safe Parking.” Put
blocks at front and rear of drive wheels.
SA-2-4 l Lifting, Jacking, and Blocking SM 636,Oct ‘96
11. ClflRU Group SA, Safe Maintenance
2. Put a floor jack under the steer axle mounting frame
member, centered between the two wheels.
A WARNING
Never lift the truck by the counterweight.
3.
4.
NOTE
If there is insufficient clearance under
frame for your jack, the truck may first be
driven onto shims, such as 25 x 150 x 300
mm (1 x 6 x 12 in) pieces of board, to
increase the truck frame underclearance.
Raise the truck only as high asnecessary to perform the
maintenance work.
Put blocks at both sides of the truck, fully under the
frame main side structure. Put the blocks infront of but
close to the counterweight and steer wheels for best
truck stability.
Put equal blocks under each side of the truck to provide
a level working position.
5. Lower the truck onto the blocks and remove the jack.
A CAUTION
Before performing any maintenance, check
the truck for stability on the blocks.
6. When maintenance work is completed, lower the rear
of truck to the floor by reversing the above procedure
and lowering each side of the truck 50 mm (2 in) at a
time:
.l Put jack under frame and raise truck.
l Carefully remove blocks and lower truck.
l Remove jack and blocks from drive’wheels.
RaisingEntireTruck
Refer to truck data plate for truck weights.
1.
2.
Park truck safely as described in “Safe Parking.”
Lower upright fully.
If necessary, drive truck onto boards to increase
underclearance.
A WARNING
SIDE-TO-SIDE TIPOVER. When jacking
side of truck, be sure upright is lowered
fully and do not raise one side of the truck
more than about 50 mm (2 in) higher than
the other, to avoid tipping truck over later-
ally.
END-TO-END TIPOVER. If the upright
and transaxle are removed while the truck
is blocked up, the truck will tip backwards
due to the heavy counterweight. Both up-
right and counterweight must be removed
before attempting to raise the truck for
transaxle removal. The back of the truck
must be supported by blocking under the
steer axle to prevent movement.
The reverse is also true. If the counter-
weight is removed while the truck is up on
blocks, the weight of the upright and
transaxle will cause the truck to tip on the
front blocks and fall forward.
SM 638, Ott ‘98 Lifting, Jacking, and Blocking l SA-2-5
12. Group SA, Safe Maintenance CMRlC
3. Put the jack under side frame near the center of the
truck.
4.
5.
IMPORTANT
Be sure to put the jack squarely and fully
under the main side structure of the frame.
Do not put the jack under the outer covers
which enclose the fuel and hydraulic sump
tanks.
Carefully raise the truck one side at a time, only as high
as necessary to do the maintenance work and not more
than a maximum of 150 mm (6 in) total.
Put blocks under the side frame, at each side of thejack.
Spread the blocks close to the steer and drive wheels
for maximum stability.
6.
7.
If using one jack, lower the truck onto the blocks and
move the jack to the opposite side. Repeat the lifting
procedure.
Put the same size blocks under each side of the truck so
it will be level.
A CAUTION
Before performing any maintenance work,
check the truck for stable condition on the
blocking.
When maintenance work is completed, lower the en-
tire truck to the floor by reversing the lifting procedure.
Lower the truck one side at a time, while carefully
removing the blocks. Check to be sure no tools or
equipment are under the truck or wheels.
NOTE
Depending on jack height, shims under the
tires may be needed for clearance to allow
removal of jack.
Shipping Tie-Down Instructions
Front of Truck
a. With Upright and Carriage Installed
l Lower the carriage fully.
l Put a tie down (e.g., chain) between the carriage
fork bars.
b. Without an Upright and Carriage Installed
l Put a chain across the truck floor plate. Protect
truck from chain damage by using covered chain
or protective material under the chain at contact
points.
2. Rear of Truck
l Attach the tie down to pocket in bottom of coun-
terweight.
SA-2-6 . Lifting, Jacking, and Blocking SM 638,Oct ‘98
13. GlaRK Group SA, Safe Maintenenance
Section 3.
Towing
If your truck is disabled but can be moved freely on its own
wheels without further damage, use the following proce-
dures to tow the truck safely to a repair area.
A WARNING
It is important for your safety and to the
care of your lift truck to use the proper
equipment and carefully follow these rec-
ommendations for safe towing.
Do not tow a lift truck if there is a problem
with the brakes or tires, or if the steering
cannot be operated.
Do not tow the disabled truck up or down
ramps or steep inclines.
Do not attempt to tow the disabled truck if
traction or weather conditions are poor.
Be sure to apply the parking brake or block the drive
wheels on the disabled truck while working around it.
When possible, raise the carriage (forks) on the dis-
abled truck 300 mm (12 in) from the floor or ground.
Secure the carriage on the upright with a chain.
Use a truck for towing that is of equal or larger capacity
than the disabled truck. Carry a partial load on the tow
truck for improved traction.
4.
5.
6.
Check that the counterweight bolts on both trucks are
in place and properly torqued to 340-380 Nom (250-
280 ft-lb). These bolts aremade of special, high-tensile
steel and are not commercially available. When neces-
sary, replace these bolts only with a genuine Clark
replacement part.
Use an approved, solid metal tow bar with towing
couplers that connect to the towing pins in the counter-
weights.
NOTE
DOT-approved towing equipment is avail-
able from your Clark dealer.
Release the parking brake on the towed vehicle. Place
directional control lever in neutral.
Tow the disabled truck backwards. An operator must
be on the disabled truck.
A CAUTION
The power steering will not operate on the
disabled truck when the engine is not run-
ning. The steering handwheel will be diffi-
cult to turn.
Tow the truck slowly. Careful towing is necessary to
prevent injury to personnel or damage to the disabled
truck. The truck should be towed at a speed of less than
8 kph (5 mph, or a moderate walking speed) with a
driver in place and steering the disabled truck.
Direction of towing for distances of
300 meters (325 yards) or less.
Disabled truck with Tow truck moving at 8 kilome-
driver in place to steer. ters-per-hour (5 mph) or less.
SM 638,Oct ‘98 Towing l SA-3-l
14. Group SA, Safe Maintenance CMK
9.
IMPORTANT
Do not lift the disabled truck or any wheels
off the floor while the truck is being towed.
A WARNING
Always engage the parking brake when
parking a lift truck. The truck can roll and
Park the disabled truck in authorized areas only. Fully
lower the forks on the floor, leave the directional
control in neutral, turn the ignition switch to OFF, and
engage the parking brake. Remove the ignition key
and, when necessary, block the wheels to prevent the
truck from rolling.
cause injury or death to personnel near it.
SA-3-2 l Towing SM 638,Oct ‘98
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. GROUP PS
PERIODIC SERVICE
Maintenance Schedules .................................................. Section 1
The Planned Maintenance Program ............................. Section 2
The PM Inspection Form ............................................... Section 3
SM 638,Oct ‘98 Periodic Service
17. GrouD PS, Periodic Service
Section 1.
Maintenance Schedules
“Periodic Service” and “Planned
Maintenance”
The term “periodic service” includes all maintenance tasks
that should be performed on a regularly scheduled basis.
The term “Planned Maintenance” indicates a formalized
program of basic inspections, adjustments, and lubrications
that the Clark service organization provides customers at a
prescribed interval, usually 50-250 hours. The recommended
basic “Planned Maintenance” procedure is given in Section
2 of this Group.
The current Section,“Maintenance Schedules,” specifies
all maintenance tasks-including Planned Maintenance
tasks-that should be performed periodically, and suggests
intervals at which they should be performed.
Determining Maintenance Intervals
Time intervals on the charts on the next four pages and
elsewhere in this manual relate to truck operating hours as
recorded on the hourmeter, and are based on experience
Clark has found to be convenient and suitable under nor-
mal operation. Standard operating condition classifications
are:
Normal Operation: Eight-hour material handling, mostly
in buildings or in clean, open air on clean, paved surfaces.
Severe Operation: Prolonged operating hours or constant
usage.
Extreme Operation:
In sandy or dusty locations, such as cement plants,
lumber mills, and coal dust or stone crushing sites.
High-temperature locations, such as steel mills and
foundries.
Sudden temperature changes, such as constant trips
from buildings into the open air, or in refrigeration
plants.
If the lift truck is used in severe or extreme operating
conditions, the maintenance intervals should be shortened
accordingly.
IMPORTANT
MAINTENANCE INTERVALS. If the lift
truck is used in severe or extreme operat-
ing conditions, the maintenance intervals
should be shortened accordingly.
Since the operating environments of lift
trucks vary widely, the above descriptions
are highly generalized and should be ap-
plied as actual conditions dictate.
SM 638, Ott ‘98 Maintenance Schedules l PS-l-l