Certification for installation of SF6 Gas Insulated Switchgear

•

1 like•130 views

Certification for installation of SF6 Gas Insulated Switchgear

600 Series Interface D Compact Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface D bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables. 600 Series Interface D, Elastimold Bushings * Bushing Voltage Range 12kV-24kV * Bushing Current Rating 800Amps * Bushing Type 5/8" Bolted Aluminium Stud Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 600 Series Connectors - 676LRA Tee Connectors, 12-24kV 1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination.

Elastimold Connectors - Loadbreak & Deadbreak Elbow & Bolted Tee Connectors -...

Thorne & Derrick International

700 Series Interface E Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface E bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables. 700 Series Interface E, Elastimold Bushings * Bushing Voltage Range 33kV-36kV * Bushing Current Rating 800Amps & 1250Amps * Bushing Type 5/8" Bolted Aluminium Insert Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 700 Series Connectors - 750LR Tee Connectors & 775LR Tee Connectors 800-1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the Elastimold high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination. HV High Voltage Cable Connectors, Specification - Elastimold dead-break separable cable connectors suit all international high voltage bushing interfaces for the termination of HV cable into switchgear, transformers and motors. Elastimold cable connectors terminate high voltage power cables (typically 11kV, 15kV, 24kV, 33kV, 36kV up to 52kV) into SF6 GIS gas insulated switchgear including Schneider, ABB, Areva and Siemens. Elastimold cable connectors meet the requirements of ANSI/IEEE 386 & 404 and CENELEC EN50180 & EN50181 for high voltage "dead-break" cable connection, i..e connectors installed and terminated onto un-energised high voltage power cable. US specification "load-break" cable connectors for high voltage energised cable termination are available. High Voltage Cable Connectors - Elastimold cable connectors (elbow and straight types) are specified to terminate XLPE or EPR insulated high voltage power cables with copper tape or copper wire screens up to 52kV. Elastimold cable connectors are available to suit and terminate lead covered HV cables for hydro-carbon industries (oil, gas, petrochemicals) with ATEX certification for hazardous area Zones 1 and Zones 2.

Factors considered for High Voltage Cable Joint design Shahab Khan

Nexans Euromold Connectors - Enquiry Form

Thorne & Derrick International

LV-HV Cable Jointers Tools for 1000V, 11kV, 33kV Cable Preparation. Low voltage cable jointing tools for cable stripping and cable preparation of DNO utility and industrial power cables including waveform, consac, XLPE and PILC. High voltage cable jointing tools enable the cable preparation, stripping, cutting and removal of insulation (XLPE, EPR), semi-conductive screens (bonded and peelable) and outer cable sheaths (PVC, PE, EPR) from single and multi-core 11-33kV cables, including Triplex cable. T&D also stock and distribute Cembre Cable Crimping & Cable Cutting Tools and SEB Cable Pulling and Laying Equipment including cable rollers, cable socks, drum jacks and conduit rods.

Types of wires and cables ic

Vishal Patel

Power cablescollege

Underground cables

Anu71

Types of wires,cables,connectors and switches

Akash Gajjar

English Adventure Starter AMy schools: Escuela 25 DE 12, Escuela 7 DE 17

Under ground cables presention

Razu Khan

Since the loads having the trends towards growing density. This requires the better appearance, rugged construction, greater service reliability and increased safety. An underground cable essentially consists of one or more conductors covered with suitable insulation and surrounded by a protecting cover. The interference from external disturbances like storms, lightening, ice, trees etc. should be reduced to achieve trouble free service. The cables may be buried directly in the ground, or may be installed in ducts buried in the ground.

updated CV YacoubMahmoud Yacoub

APM07-planning & shedulingMahmoud Yacoub

abb site managment competenciesMahmoud Yacoub

Appreciation letter -AlFanar companyMahmoud Yacoub

Appreciation letter -AlGihaz companyMahmoud Yacoub

Aryaf Construction Co.Mahmoud Yacoub

Central Electicity Generation CoMahmoud Yacoub