ccna presentatidon day 4

1. 1

2. Layer 2 Switching
 Switching breaks up large collision domains into
smaller ones
 Collision domain is a network segment with two or
more devices sharing the same bandwidth.
 A hub network is a typical example of this type of
technology
 Each port on a switch is actually its own collision
domain, you can make a much better Ethernet LAN
network just by replacing your hubs with switches
2

3. Switching Services
 Unlike bridges that use software to create and manage
a filter table, switches use Application Specific
Integrated Circuits (ASICs)
 Layer 2 switches and bridges are faster than routers
because they don’t take up time looking at the Network
layer header information.
 They look at the frame’s hardware addresses before
deciding to either forward the frame or drop it.
 layer 2 switching so efficient is that no modification to
the data packet takes place
3

4. How Switches and Bridges
Learn Addresses
Bridges and switches learn in the following ways:
• Reading the source MAC address of each
received frame or datagram
• Recording the port on which the MAC address
was received.
In this way, the bridge or switch learns which addresses
belong to the devices connected to each port.
4

5. Ethernet Access with Hubs
5

6. Ethernet Access with Switches
6

7. ❑Address learning
❑Forward/filter decision
❑Loop avoidance
Ethernet Switches and Bridges

8. Switch Features
❑ There are three conditions in which a switch will flood a
frame out on all ports except to the port on which the
frame came in, as follows:
Unknown unicast address
Broadcast frame
Multicast frame
8

9. MAC Address Table
• Initial MAC address table is empty.
9

10. Learning Addresses
• Station A sends a frame to station C.
• Switch caches the MAC address of station A to port E0 by
learning the source address of data frames.
• The frame from station A to station C is flooded out to all
ports except port E0 (unknown unicasts are flooded). 10

11. Learning Addresses (Cont.)
• Station D sends a frame to station C.
• Switch caches the MAC address of station D to port E3 by
learning the source address of data frames.
• The frame from station D to station C is flooded out to all ports
except port E3 (unknown unicasts are flooded). 11

12. Filtering Frames
• Station A sends a frame to station C.
• Destination is known; frame is not flooded.
12

13. • Station D sends a broadcast or multicast frame.
• Broadcast and multicast frames are flooded to all ports
other than the originating port.
Broadcast and Multicast
Frames
13

14. Forward/Filter Decision
❑ When a frame arrives at a switch interface, the destination
hardware address is compared to the forward/ filter MAC
database.
❑ If the destination hardware address is known and listed in the
database, the frame is sent out only the correct exit interface
❑ If the destination hardware address is not listed in the MAC
database, then the frame is flooded out all active interfaces
except the interface the frame was received on.
❑ If a host or server sends a broadcast on the LAN, the switch will
flood the frame out all active ports except the source port.
14

15. Learning Mac Address
15

16. Learning Mac Address
16

17. Learning Mac Address
17

18. Learning Mac Address
18

19. Learning Mac Address
19

20. Learning Mac Address
20

21. Learning Mac Address
21

22. Forward/Filter PC3 to PC1
22

23. Forward/Filter PC3 to PC2
23

24. Loop Avoidance
• Redundant links between
switches are a good idea
because they help
prevent complete network
failures in the event one
link stops working
• However, they often
cause more problems
because frames can be
flooded down all
redundant links
simultaneously
• This creates network
loops
24

25. Network Broadcast Loops
❑ A manufacturing floor PC sent a
network broadcast to request a
boot loader
❑ The broadcast was first received
by switch sw1 on port 2/1
❑ The topology is redundantly
connected; therefore, switch
sw2 receives the broadcast
frame as well on port 2/1
❑ Switch sw2 is also receiving a
copy of the broadcast frame
forwarded to the LAN segment
from port 2/2 of switch sw1.
❑ In a small fraction of the time,
we have four packets. The
problem grows exponentially
until the network bandwidth is
saturated
25

26. Multiple Frame Copies
26

27. 27

28. Overview
❑Redundancy in a network is extremely important
because redundancy allows networks to be fault
tolerant.
❑Redundant topologies based on switches and bridges
are subject to broadcast storms, multiple frame
transmissions, and MAC address database instability.
❑Therefore network redundancy requires careful
planning and monitoring to function properly.
❑The Spanning-Tree Protocol is used in switched
networks to create a loop free network 28

29. • Provides a loop-free redundant network topology by
placing certain ports in the blocking state.
Spanning-Tree Protocol
29

30. Spanning Tree Protocol
❑Spanning Tree Protocol resides in Data link Layer
❑Ethernet bridges and switches can implement the IEEE 802.1D
Spanning-Tree Protocol and use the spanning-tree algorithm to
construct a loop free network.
30

31. • Spanning-tree transits each port through several different states:
Spanning-Tree Port States
Disabled
31

32. Selecting the Root Bridge
❑The first decision that all switches in the network make, is to identify the
root bridge.
❑When a switch is turned on, the spanning-tree algorithm is used to
identify the root bridge. BPDUs are sent out with the Bridge ID (BID).
❑The BID consists of a bridge priority that defaults to 32768 and the switch
base MAC address.
❑When a switch first starts up, it assumes it is the root switch and sends
BPDUs. These BPDUs contain BID.
❑All bridges see these and decide that the bridge with the smallest BID
value will be the root bridge.
❑A network administrator may want to influence the decision by setting
the switch priority to a smaller value than the default.
32

33. Spanning Tree Protocol Terms
❑BPDU Bridge Protocol Data Unit (BPDU) - All the switches exchange information to use in the
selection of the root switch
❑Bridge ID - The bridge ID is how STP keeps track of all the switches in the network. It is determined by
a combination of the bridge priority (32,768 by default on all Cisco switches) and the base MAC address.
❑Root Bridge -The bridge with the lowest bridge ID becomes the root bridge in the network.
❑Nonroot bridge - These are all bridges that are not the root bridge.
❑Root port - The root port is always the link directly connected to the root bridge or the shortest path
to the root bridge. If more than one link connects to the root bridge, then a port cost is determined by
checking the bandwidth of each link.
❑Designated port - A designated port is one that has been determined as having the best (lowest)
cost. A designated port will be marked as a forwarding port
❑Nondesignated Port - A nondesignated port is one with a higher cost than the designated port.
Nondesignated ports are put in blocking mode
❑Forwarding Port - A forwarding port forwards frames
❑Blocked Port - A blocked port is the port that will not forward frames, in order to prevent loops 33

34. • Bpdu = Bridge Protocol Data Unit
(default = sent every two seconds)
• Root bridge = Bridge with the lowest bridge ID
• Bridge ID =
• In the example, which switch has the lowest bridge ID?
Spanning-Tree Protocol
Root Bridge Selection
34

35. • One root bridge per network
• One root port per nonroot bridge
• One designated port per segment
• Nondesignated ports are unused
Spanning-Tree Operation
35

36. Selecting the Root Port
The STP cost is an accumulated total path cost based on the rated
bandwidth of each of the links
This information is then used internally to select the root port for that
device
36

37. • One root bridge per network
• One root port per nonroot bridge
• One designated port per segment
• Nondesignated ports are unused
Spanning-Tree Operation
37

38. Switching Methods
1. Cut-Through (Fast Forward)
The frame is forwarded through the switch before the entire frame is
received. At a minimum the frame destination address must be read
before the frame can be forwarded. This mode decreases the latency of
the transmission, but also reduces error detection.
2. Fragment-Free (Modified Cut-Through)
Fragment-free switching filters out collision fragments before forwarding
begins. Collision fragments are the majority of packet errors. In
Fragment-Free mode, the switch checks the first 64 bytes of a frame.
3. Store-and-Forward
The entire frame is received before any forwarding takes place. Filters
are applied before the frame is forwarded. Most reliable and also most
latency especially when frames are large.
38

39. Switching Methods
39

40. 40

41. Physical Startup of the Catalyst
Switch
❑Switches are dedicated, specialized computers, which contain a CPU,
RAM, and an operating system.
❑Switches usually have several ports for the purpose of connecting
hosts, as well as specialized ports for the purpose of management.
❑A switch can be managed by connecting to the console port to view
and make changes to the configuration.
❑Switches typically have no power switch to turn them on and off.
They simply connect or disconnect from a power source.
41

42. Switch LED Indicators
❑The front panel of a switch has several lights to help monitor system
activity and performance. These lights are called light-emitting diodes
(LEDs). The switch has the following LEDs:
o System LED
o Remote Power Supply (RPS) LED
o Port Mode LED
o Port Status LEDs
❑The System LED shows whether the system is receiving power and
functioning correctly.
❑The RPS LED indicates whether or not the remote power supply is in use.
❑The Mode LEDs indicate the current state of the Mode button.
❑The Port Status LEDs have different meanings, depending on the current
value of the Mode LED.
42

43. Verifying Port LEDs During Switch
POST
❑Once the power cable is connected, the switch initiates a
series of tests called the power-on self test (POST).
❑POST runs automatically to verify that the switch functions
correctly.
❑The System LED indicates the success or failure of POST.
43

44. Switch Command Modes
❑Switches have several command modes.
❑The default mode is User EXEC mode, which ends in a greater-
than character (>).
❑The commands available in User EXEC mode are limited to
those that change terminal settings, perform basic tests, and
display system information.
❑The enable command is used to change from User EXEC mode
to Privileged EXEC mode, which ends in a pound-sign character
(#).
❑The configure command allows other command modes to be
accessed. 44

45. Show Commands in User-Exec Mode
45

46. Tasks
Setting the passwords (Password must be between 4
and 8 characters)
Setting the hostname
Configuring the IP address and subnet
mask
Erasing the switch configurations
46

47. Setting Switch Hostname
Setting Passwords on Lines
47

48. Switch Configuration
❑ There are two reasons to set the IP address information on the switch:
 To manage the switch via Telnet or other management software
 To configure the switch with different VLANs and other network functions
 See the default IP configuration = show IP command
Configure IP Address
sw1(config-if)#interface vlan 1
sw1(config-if)#ip address 10.0.0.1 255.0.0.0
sw1(config-if)#no shut
sw1(config-if)#exit
sw1(config)ip default-gateway 10.0.0.254
48

49. Configuring Interface Descriptions
❑ You can administratively set a name for each interface on the
switches
SW1#config t
Enter configuration commands, one per line. End with CNTL/Z
SW1(config)#int e0/1
SW1(config-if)#description Finance_VLAN
SW1(config-if)#int f0/26
SW1(config-if)#description trunk_to_Building_4
SW1(config-if)#
❑ Setting Port Security
Sw1(config-if)#switchport port-security mac-address mac-address
 Now only this one MAC address is allowed on this switch port
49

50. Switch Configuration
Connect two machine to a switch
To view the MAC table
sw1#show mac-address-table dynamic
Sw1#sh spanning-tree
Sw1(config)#spanning-tree vlan 1 priority ?
Sw1(config)#spanning-tree vlan 1 priority 4096
Erase the configuration
50

51. 51

52. VLAN’s
❑ A VLAN is a logical grouping of network users and
resources connected to administratively defined ports
on a switch.
❑ Ability to create smaller broadcast domains within a
layer 2 switched internetwork by assigning different
ports on the switch to different subnetworks.
❑ Frames broadcast onto the network are only switched
between the ports logically grouped within the same
VLAN
❑ By default, no hosts in a specific VLAN can communicate
with any other hosts that are members of another VLAN,
❑ For Inter VLAN communication you need routers
52

53. VLANs
❑VLAN implementation combines Layer 2 switching and Layer 3 routing
technologies to limit both collision domains and broadcast domains.
❑VLANs can also be used to provide security by creating the VLAN
groups according to function and by using routers to communicate
between VLANs.
❑A physical port association is used to implement VLAN assignment.
❑Communication between VLANs can occur only through the router.
❑This limits the size of the broadcast domains and uses the router to
determine whether one VLAN can talk to another VLAN.
❑NOTE: This is the only way a switch can break up a broadcast domain!
53

54. A VLAN = A Broadcast Domain = Logical Network (Subnet)
VLAN Overview
• Segmentation
• Flexibility
• Security
54

55. History
❑11 Hosts are connected to the switch
❑All From same Broadcast domain
❑Need to divide them in separate logical segment
❑High broadcast traffic reasons
❑ ARP
❑ DHCP
❑ SAP
❑ XWindows
❑ NetBIOS
55

56. Definition
❑ Logically Defined community of interest that limits a
Broadcast domain
❑ LAN are created on the software of Switch
❑ All devices in a VLAN are members of the same
broadcast domain and receive all broadcasts
❑ The broadcasts, by default, are filtered from all ports
on a switch that are not members of the same VLAN.
56

57. Security
❑ A Flat internetwork’s security used to be tackled by connecting
hubs and switches together with routers
❑ This arrangement is ineffective because
❑ Anyone connecting physical network could access network resources
located on that physical LAN
❑ Can observe the network traffic by plugging network analyzer into the
HUB
❑ Users could join a workgroup by just plugging their workstations into
the existing hub
❑ By creating VLAN’s administrators have control over each port and
user
57

58. How VLANs Simplify Network
Management
❑ If we need to break the broadcast domain we need to connect a
router
❑ By using VLAN’s we can divide Broadcast domain at Layer-2
❑ A group of users needing high security can be put into a VLAN so
that no users outside of the VLAN can communicate with them.
❑ As a logical grouping of users by function, VLANs can be
considered independent from their physical locations.
58

59. VLAN Memberships
❑ VLAN created based on port is known as Static VLAN.
❑ VLAN assigned based on hardware addresses into a
database, is called a dynamic VLAN
59

60. VLAN Membership Modes
60

61. Static VLANs
❑Most secure
❑Easy to set up and monitor
❑Works well in a network where the movement
of users within the network is controlled
61

62. Dynamic VLANs
❑ A dynamic VLAN determines a node’s VLAN assignment
automatically
❑ Using intelligent management software, you can base
VLAN assignments on hardware (MAC) addresses.
❑ Dynamic VLAN need VLAN Management Policy Server
(VMPS) server
62

63. LAB – Creating VLAN
❑ Connect two computers on a switch
❑ Ping and see both are able to communicate
❑ Create two vlans and configure static VLAN’s so both ports are on separate VLAN’s
❑ Test the communication between PC’s
port1 port5
To see the existing VLAN
#Show vlan
To create VLAN
#vlan database
Switch(vlan)#vlan 2 name red
Switch(vlan)#vlan 3 name blue
Assigning ports to VLAN
Sw(config)# int fastEthernet 0/1
Sw(config-if)#switch mode access
Sw(config-if)#switchport access vlan2
63

64. LAB – Deleting VLAN
port1 port5
To delete VLAN
Sw(config)# no vlan 2
Sw(config)# no vlan 3
To bring port back to VLAN 1
Sw(config-if)#switchport mode acces
Sw(config-if)#switch port access vlan1
For a Range
Sw(config)#int range fastethernet 0/1 - 5
Sw(config-if)#switch port access vlan1
64

65. ❑VLANs can span across multiple switches.
❑Trunks carry traffic for multiple VLANs.
❑Trunks use special encapsulation to distinguish between
different VLANs.
VLAN Operation
65

66. Types of Links
❑ Access links
❑ This type of link is only part of one VLAN
❑ It’s referred to as the native VLAN of the port.
❑ Any device attached to an access link is unaware of a VLAN
❑ Switches remove any VLAN information from the frame before
it’s sent to an access-link device.
❑ Trunk links
❑ Trunks can carry multiple VLANs
❑ These carry the traffic of multiple VLANs
❑ A trunk link is a 100- or 1000Mbps point-to-point link between
two switches, between a switch and router.
66

67. Access links
67

68. Trunk links
68

69. Frame Tagging
 Can create VLANs to span more than one connected switch
 Hosts are unaware of VLAN
 When host A Create a data unit and reaches switch, the switch adds a
Frame tagging to identify the VLAN
 Frame tagging is a method to identify the packet belongs to a particular
VLAN
 Each switch that the frame reaches must first identify the VLAN ID from
the frame tag
 It finds out what to do with the frame by looking at the information in the
filter table
 Once the frame reaches an exit to an access link matching the frame’s
VLAN ID, the switch removes the VLAN identifier
69

70. Frame Tagging Methods
❑ There are two frame tagging methods
 Inter-Switch Link (ISL)
 IEEE 802.1Q
❑ Inter-Switch Link (ISL)
 proprietary to Cisco switches
 used for Fast Ethernet and Gigabit Ethernet links only
❑ IEEE 802.1Q
 Created by the IEEE as a standard method of frame
tagging
 it actually inserts a field into the frame to identify the
VLAN
 If you’re trunking between a Cisco switched link and a
different brand of switch, you have to use 802.1Q for the
trunk to work.
70

71. ❑ Performed with
ASIC
❑ ISL header not
seen by client
❑ Effective between
switches, and
between routers and
switches
ISL trunks enable VLANs across a backbone.
ISL Tagging
71

72. LAB-Creating Trunk
Create two VLAN's on each
switches
#vlan database
sw(vlan)#vlan 2 name red
sw(vlan)#vlan 3 name blue
sw(vlan)#exit
sw#config t
sw(config)#int fastethernet 0/1
sw(config-if)#switch-portaccess vlan
2
sw(config)#int fastethernet 0/4
sw(config-if)#switch-portaccess vlan
3
To see Interface status
#show interface status
10.0.0.3
10.0.0.4
1 2 3 4
1 2 3 4
10.0.0.1
10.0.0.2
24 12
Trunk Port Configuration
sw#config t
sw(config)#int fastethernet 0/24
sw(config-if)#switchport trunk
encapsulation dot1q
sw(config-if)#switchport mode trunk
* 2950 Only dot1q Encapsulation
72

73. Assigning Access Ports to a
VLAN
Switch(config)#interface gigabitethernet 1/1
• Enters interface configuration mode
Switch(config-if)#switchport mode access
• Configures the interface as an access port
Switch(config-if)#switchport access vlan 3
• Assigns the access port to a VLAN
73

74. Verifying the VLAN
Configuration
Switch#show vlan [id | name] [vlan_num | vlan_name]
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/5, Fa0/7
Fa0/8, Fa0/9, Fa0/11, Fa0/12
Gi0/1, Gi0/2
2 VLAN0002 active
51 VLAN0051 active
52 VLAN0052 active
…
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 1002 1003
2 enet 100002 1500 - - - - - 0 0
51 enet 100051 1500 - - - - - 0 0
52 enet 100052 1500 - - - - - 0 0
…
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
74

75. Verifying the VLAN Port
Configuration
Switch#show running-config interface {fastethernet |
gigabitethernet} slot/port
• Displays the running configuration of the interface
Switch#show interfaces [{fastethernet | gigabitethernet}
slot/port] switchport
• Displays the switch port configuration of the interface
Switch#show mac-address-table interface interface-id [vlan
vlan-id] [ | {begin | exclude | include} expression]
• Displays the MAC address table information for the specified
interface in the specified VLAN
75

76. ❑A messaging system that advertises VLAN configuration information
❑Maintains VLAN configuration consistency throughout a common
administrative domain
❑Sends advertisements on trunk ports only
VTP Protocol Features

77. VLAN Trunking Protocol (VTP)
❑Benefits of VTP
❑Consistent VLAN configuration across all switches in
the network
❑Accurate tracking and monitoring of VLANs
❑Dynamic reporting of added VLANs to all switches in
the VTP domain
77

78. • Forwards
advertisements
• Synchronizes
• Not saved in
NVRAM
• Creates VLANs
• Modifies VLANs
• Deletes VLANs
• Sends/forwards
advertisements
• Synchronizes
• Saved in NVRAM
• Creates VLANs
• Modifies VLANs
• Deletes VLANs
• Forwards
advertisements
• Does not
synchronize
• Saved in NVRAM
VTP Modes
78

79. VTP Operation
• VTP advertisements are sent as multicast frames.
• VTP servers and clients are synchronized to the latest update identified
revision number.
• VTP advertisements are sent every 5 minutes or when there is a change.
79

80. VTP Pruning
• VTP pruning provides a way for you to preserve
bandwidth by configuring it to reduce the amount of
broadcasts, multicasts, and unicast packets.
• If Switch A doesn’t have any ports configured for VLAN
5, and a broadcast is sent throughout VLAN 5, that
broadcast would not traverse the trunk link to Switch A.
• By default, VTP pruning is disabled on all switches.
• Pruning is enabled for the entire domain
80

81. • Increases available bandwidth by reducing unnecessary flooded traffic
• Example: Station A sends broadcast, and broadcast is flooded only toward
any switch with ports assigned to the red VLAN
VTP Pruning
81

82. VTP Configuration Guidelines
– Configure the following:
• VTP domain name
• VTP mode (server mode is the default)
• VTP pruning
• VTP password
Switch(config)#vtp mode server
Switch(config)#vtp domain gates
SwitchA#sh vtp status
82

83. wg_sw_1900#configure terminal
Enter configuration commands, one per line. End with CNTL/Z
wg_sw_1900(config)#vtp transparent
wg_sw_1900(config)#vtp domain switchlab
wg_sw_1900(config)#vtp [server | transparent | client] [domain
domain-name] [trap {enable | disable}] [password password]
[pruning {enable | disable}]
Creating a VTP Domain
Catalyst 1900
Catalyst 2950
wg_sw_2950#vlan database
wg_sw_2950(vlan)#vtp [ server | client | transparent ]
wg_sw_2950(vlan)#vtp domain domain-name
wg_sw_2950(vlan)#vtp password password
wg_sw_2950(vlan)#vtp pruning
83

84. Verifying the VTP
Configuration
Switch#show vtp status
Switch#show vtp status
VTP Version : 2
Configuration Revision : 247
Maximum VLANs supported locally : 1005
Number of existing VLANs : 33
VTP Operating Mode : Client
VTP Domain Name : Lab_Network
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x45 0x52 0xB6 0xFD 0x63 0xC8 0x49 0x80
Configuration last modified by 0.0.0.0 at 8-12-99 15:04:49
Switch#
84

85. Verifying the VTP
Configuration (Cont.)
Switch#show vtp counters
Switch#show vtp counters
VTP statistics:
Summary advertisements received : 7
Subset advertisements received : 5
Request advertisements received : 0
Summary advertisements transmitted : 997
Subset advertisements transmitted : 13
Request advertisements transmitted : 3
Number of config revision errors : 0
Number of config digest errors : 0
Number of V1 summary errors : 0
VTP pruning statistics:
Trunk Join Transmitted Join Received Summary advts received from
non-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Fa5/8 43071 42766 5
85

86. VLAN to VLAN
❑If you want to connect between two
VLANs you need a layer 3 device
86

87. Router on Stick
10.0.0.3
20.0.0.3
1 2 3 4
1 2 3 4
10.0.0.2
20.0.0.2
24 12
Create two VLAN's on each
switches
#vlan database
sw(vlan)#vlan 2 name red
sw(vlan)#vlan 3 name blue
sw(vlan)#exit
sw#config t
sw(config)#int fastethernet 0/1
sw(config-if)#switch-portaccess vlan 2
sw(config)#int fastethernet 0/4
sw(config-if)#switch-portaccess vlan 3
To see Interface status
#show interface status
Trunk Port Configuration
sw#config t
sw(config)#int fastethernet 0/24
sw(config-if)#switchport trunk
encapsulation dot1q
sw(config-if)#switchport mode trunk
Router Configuration
R1#config t
R1(config)#int fastethernet 0/0.1
R1(config-if)#encapsulation dot1q 2
R1(config-if)#ip address 10..0.0.1 255.0.0.0
R1(config-if# No shut
R1(config-Iif)# EXIT
R1(config)#int fastethernet 0/0.2
R1(config-if)# encapsulation dot1q 3
R1(config-if)#ip address 20..0.0.1 255.0.0.0
R1(config-if# No shut
Router-Switch Port to be made as Trunk
sw(config)#int fastethernet 0/9
sw(config-if)#switchport trunk enacapsulation
dot1q
sw(config-if)#switchport mode trunk
10.0.0.1
20.0.0.1
FA0/0
9
87

88. Fig. 3 NAT (TI1332EU02TI_0003 New Address Concepts, 7)
88

89. New Addressing Concepts
Problems with IPv4
Shortage of IPv4 addresses
Allocation of the last IPv4 addresses was for the year 2005
Address classes were replaced by usage of CIDR, but this is not sufficient
Short term solution
NAT: Network Address Translator
Long term solution
IPv6 = IPng (IP next generation)
Provides an extended address range
Fig. 2 Address shortage and possible solutions (TI1332EU02TI_0003 New Address Concepts, 5)
89

90. NAT: Network Address Translator
NAT
Translates between local addresses and public ones
Many private hosts share few global addresses
Public Network
Uses public addresses
Public addresses are
globally unique
Private Network
Uses private address range
(local addresses)
Local addresses may not
be used externally
Fig. 4 How does NAT work? (TI1332EU02TI_0003 New Address Concepts, 9)
90

91. NAT Addressing Terms
❑ Inside Local
 The term “inside” refers to an address used for a host inside an
enterprise. It is the actual IP address assigned to a host in the
private enterprise network.
❑ Inside Global
 NAT uses an inside global address to represent the inside host as
the packet is sent through the outside network, typically the
Internet.
 A NAT router changes the source IP address of a packet sent by an
inside host from an inside local address to an inside global address
as the packet goes from the inside to the outside network.
91

92. Inside/Outside
92

93. Inside/Outside
93

94. NAT Addressing Terms
❑ Outside Global
 The term “outside” refers to an address used for a host outside
an enterprise, the Internet.
 An outside global is the actual IP address assigned to a host
that resides in the outside network, typically the Internet.
❑ Outside Local
 NAT uses an outside local address to represent the outside
host as the packet is sent through the private network.
 This address is outside private, outside host with a private
address
94

95. Network Address Translation
• An IP address is either local or global.
• Local IP addresses are seen in the inside network.
95

96. Types Of NAT
❑There are different types of NAT that can
be used, which are
Static NAT
Dynamic NAT
Overloading NAT with PAT (NAPT)
96

97. Static NAT
❑ Static NAT - Mapping an unregistered IP address to a registered IP
address on a one-to-one basis. Particularly useful when a device
needs to be accessible from outside the network.
❑ In static NAT, the computer with the IP address of 192.168.32.10
will always translate to 213.18.123.110.
97

98. Dynamic NAT
❑ Dynamic NAT - Maps an unregistered IP address to a registered IP
address from a group of registered IP addresses.
❑ In dynamic NAT, the computer with the IP address 192.168.32.10
will translate to the first available address in the range from
213.18.123.100 to 213.18.123.150.
98

99. Overloading NAT with PAT (NAPT)
❑ Overloading - A form of dynamic NAT that maps multiple
unregistered IP addresses to a single registered IP address by using
different ports. This is known also as PAT (Port Address Translation),
single address NAT or port-level multiplexed NAT.
❑ In overloading, each computer on the private network is translated to
the same IP address (213.18.123.100), but with a different port
number assignment..
99

100. Static NAT Configuration
• For each interface you need to configure INSIDE or OUTSIDE
Fig. 2 Address shortage and possible solutions (TI1332EU02TI_0003 New Address Concepts, 5)
E0
B
A 10.0.0.1
S0
200.0.0.1
C
Internet
10.0.0.2
10.0.0.3
10.0.0.254
R1(config)#Int fastethernet 0/0
R1(config-if)# IP NAT inside
R1(config-if)##Int s 0/0
R1(config-if)# IP NAT outside
R1(config-if)# Exit
R1(config)# ip NAT inside source static 10.0.0.1 200.0.0.1
To see the table
R1(config)#show ip nat translations
R1(config)#show ip nat statistics
100

101. INSIDE/OUTSIDE
101

102. Dynamic NAT
❑ Dynamic NAT sets up a pool of possible inside global
addresses and defines criteria for the set of inside
local IP addresses whose traffic should be translated
with NAT.
❑ The dynamic entry in the NAT table stays in there as
long as traffic flows occasionally.
❑ If a new packet arrives, and it needs a NAT entry, but
all the pooled IP addresses are in use, the router
simply discards the packet.
Fig. 2 Address shortage and possible solutions (TI1332EU02TI_0003 New Address Concepts, 5)
102

103. Dynamic NAT
❑ Instead of creating static IP, create a pool of IP
Address, Specify a range
❑ Create an access list and permit hosts
❑ Link Access list to the Pool
Fig. 2 Address shortage and possible solutions (TI1332EU02TI_0003 New Address Concepts, 5)
103

104. Dynamic NAT Configuration
• For each interface you need to configure INSIDE or OUTSIDE
S0
200.0.0.1/200.0.0.254
Internet
E0
B
A 10.0.0.1
C
10.0.0.2
10.0.0.3
10.0.0.254
Create an Access List
R1(config)# Access-list 1 permit 10.0.0.0 0.255.255.255
Configure NAT dynamic Pool
R1(config)# IP NAT pool pool1 200.0.0.1 200.0.0.254 netmask 255.255.255.0
Link Access List to Pool
R1(config)# IP NAT inside source list 1 pool pool1
104

105. PAT
❑ Overloading an inside global address
❑ NAT overload only one global IP shared among all hosts
Fig. 2 Address shortage and possible solutions (TI1332EU02TI_0003 New Address Concepts, 5)
E0
B
A 10.0.0.1
C
10.0.0.2
10.0.0.3
10.0.0.254 200.0.0.1
Internet
Shared Global IP
200.0.0.1:1025
200.0.0.1:1026
200.0.0.1:1027
105

106. PAT
106

107. PAT
107

108. PAT
108

109. PAT
109

110. PAT
110

111. PAT
111

112. PAT
112

113. Configuration
113

114. PAT LAB
R1#config t
R1(config)# int e 0
R1(config-if)# ip nat insde
R1(config)# int s 0
R1(config-if)# ip nat outside
R1(config)#access-list 1 permit 192.168.10.0 0.0.0.255
R1(config)#ip nat inside source list 1 interface s 0 overload
 To see host to host ping configure static or
dynamic routing
To check translation
#sh ip nat translations
S0
S0
E0
E0
192.168.10.2
A B
200.0.0.2
192.168.10.1
200.0.0.1
192.168.20.2
192.168.20.1
R2#config t
R2(config)# int e 0
R2(config-if)# ip nat insde
R2(config)# int s 0
R2(config-if)# ip nat outside
R2(config)#access-list 1 permit 192.168.20.0 0.0.0.255
R2(config)#ip nat inside source list 1 interface s 0 overload
 To see host to host ping configure static or
dynamic routing
To check translation
#sh ip nat translations 114