1. The document provides instructions for separating, connecting, disassembling, and assembling the track on a D6H track-type tractor.
2. Key steps include loosening the track adjuster to release grease and separate the track, connecting it using a chain pulled by another vehicle, and ensuring the master link is securely bolted with the specified torque.
3. Detailed procedures are given for removing individual track links, pins, and bushings, as well as pressing new bushings into links and reassembling the track section. Proper lubrication and force limits are noted to prevent damage.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fjjsjeskkekem
This document provides instructions for disassembling and assembling the track on a D6H track-type tractor. Key steps include:
1. Separating the track by loosening it with the track adjuster and removing the master link and shoe.
2. Reconnecting the track by pulling it onto the final drive with a chain and reinstalling the master link and shoe.
3. Disassembling sections of the track by removing pins and spreading links.
4. Reassembling the track links and bushings using pressing tools and reinstalling pins and shoes. Proper torque values are specified.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsjekksemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat 953 c track loader (prefix bbx) service repair manual (bbx000...udfjjjskekdme
This document provides instructions for removing and installing track components on a Caterpillar 953C track loader. It describes:
1) Using various tools to loosen the track and remove components like the track carrier roller and track rollers.
2) Installing replacement track carrier rollers and track rollers, and adjusting the tracks.
3) Separating the track by loosening it with pins or bolts and moving the track components individually.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for servicing the track assemblies, front idlers, recoil spring assemblies, and hydraulic track adjusters of 350 and 350L excavators. It describes how to separate and reconnect the track assemblies, including removing and installing the master pin. It also details removing, disassembling, and reassembling the front idlers, as well as removing and installing the front idlers, recoil spring assemblies, and hydraulic track adjusters as a unit. Special tools are referenced throughout, and safety precautions are provided regarding the pressurized grease in the track adjusting cylinders.
Caterpillar cat d6 r track type tractor (prefix 4mn) service repair manual (4...fhhjsjekmdme
This document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor. To remove the front track roller frame, bolts and guides must be removed from the rear track roller frame. A hoist is then used to lift the front track roller frame out of the rear frame. To install it, bearings and seals are placed in the frames and the front frame is pulled into the rear frame using tooling. Recoil springs are removed by using tooling to compress the spring and turn the retainer out of the frame incrementally.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It describes removing the torque divider by draining oil, disconnecting hoses, and using lifting tools to remove it from the flywheel housing. It then details disassembling the torque divider by removing internal components like carriers, wheels, seals and bearings. The assembly section describes installing these components in reverse order and includes checks of critical clearances between parts.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fujsjfjkskefsem
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) To separate the track, the hydraulic pressure must be released from the track adjuster and the master link removed. Wood blocks are placed and the track is pulled off using chains attached to heavy equipment.
3) To connect the track, it is pulled onto the tractor using chains until the bushings engage, then the master link is reinstalled and the track tension adjusted.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fhsejkdkmen
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) Key steps include loosening the track tension, removing the master link and shoe, and using equipment to pull the track off. Reconnecting requires aligning the master link and tightening it to specification.
3) Disassembling the track involves removing pins and spreading links apart using tools, while assembling requires pressing bushings into links using a press and ensuring the seals are fully seated.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fjjsjeskkekem
This document provides instructions for disassembling and assembling the track on a D6H track-type tractor. Key steps include:
1. Separating the track by loosening it with the track adjuster and removing the master link and shoe.
2. Reconnecting the track by pulling it onto the final drive with a chain and reinstalling the master link and shoe.
3. Disassembling sections of the track by removing pins and spreading links.
4. Reassembling the track links and bushings using pressing tools and reinstalling pins and shoes. Proper torque values are specified.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsjekksemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat 953 c track loader (prefix bbx) service repair manual (bbx000...udfjjjskekdme
This document provides instructions for removing and installing track components on a Caterpillar 953C track loader. It describes:
1) Using various tools to loosen the track and remove components like the track carrier roller and track rollers.
2) Installing replacement track carrier rollers and track rollers, and adjusting the tracks.
3) Separating the track by loosening it with pins or bolts and moving the track components individually.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for servicing the track assemblies, front idlers, recoil spring assemblies, and hydraulic track adjusters of 350 and 350L excavators. It describes how to separate and reconnect the track assemblies, including removing and installing the master pin. It also details removing, disassembling, and reassembling the front idlers, as well as removing and installing the front idlers, recoil spring assemblies, and hydraulic track adjusters as a unit. Special tools are referenced throughout, and safety precautions are provided regarding the pressurized grease in the track adjusting cylinders.
Caterpillar cat d6 r track type tractor (prefix 4mn) service repair manual (4...fhhjsjekmdme
This document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor. To remove the front track roller frame, bolts and guides must be removed from the rear track roller frame. A hoist is then used to lift the front track roller frame out of the rear frame. To install it, bearings and seals are placed in the frames and the front frame is pulled into the rear frame using tooling. Recoil springs are removed by using tooling to compress the spring and turn the retainer out of the frame incrementally.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It describes removing the torque divider by draining oil, disconnecting hoses, and using lifting tools to remove it from the flywheel housing. It then details disassembling the torque divider by removing internal components like carriers, wheels, seals and bearings. The assembly section describes installing these components in reverse order and includes checks of critical clearances between parts.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fujsjfjkskefsem
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) To separate the track, the hydraulic pressure must be released from the track adjuster and the master link removed. Wood blocks are placed and the track is pulled off using chains attached to heavy equipment.
3) To connect the track, it is pulled onto the tractor using chains until the bushings engage, then the master link is reinstalled and the track tension adjusted.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...fhsejkdkmen
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) Key steps include loosening the track tension, removing the master link and shoe, and using equipment to pull the track off. Reconnecting requires aligning the master link and tightening it to specification.
3) Disassembling the track involves removing pins and spreading links apart using tools, while assembling requires pressing bushings into links using a press and ensuring the seals are fully seated.
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...ufuusjejfjkse
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) Key steps include loosening the track tension, removing the master link and shoe, and using equipment to pull the track off. Reconnecting requires aligning the master link and tightening it to specification.
3) Disassembling the track involves removing pins and spreading links apart using tools, while assembling requires pressing bushings into links using a press and ensuring the seals are fully seated.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...fjskemedcdmme
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...jfksekksmem
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...fujsjefjkskemm
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fujjdfjjskekmm
This document provides instructions for servicing the track on a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers, including using various tools to support the frame and align parts. The process ends by reconnecting the track.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fujdjjksekmem
This document provides instructions for servicing the track on a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers, including using various tools to support the frame and align parts. The process concludes by reconnecting the track.
Liebherr r964 c 1009 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 1008 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 448 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r960 demolition 1465 hydraulic excavator service repair manualdufjdjskkemm
This document is a service manual that covers maintenance and repair for various systems of an industrial machine. It includes sections on technical data, maintenance procedures, drive systems, cooling systems, hydraulics, electrical systems, gearboxes, and other components. The manual provides instructions and specifications to service the machine.
Liebherr r934 c hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for maintenance and repairs.
2. Sections covering the engine, hydraulic and electrical systems, swing gear, track components and other parts.
3. Safety symbols and instructions for working on the machines.
The manual is intended to assist customer support but does not replace technical training. It includes schematics, diagrams and detailed views of machine units.
Jcb 10 tft dumper service repair manual sn from grn1313 to grn1313dufjdjskkemm
This service manual provides instructions for servicing the components of a dumper vehicle, including the machine body and framework, operator station, engine, fuel and exhaust system, cooling system, brake system, steering system, driveline, hydraulic system, electrical system, fasteners and fixings, and consumable products. The document provides detailed procedures for removing and installing parts like fuel pipes and injector bleed-off pipes, with accompanying diagrams and special tool requirements. Safety information is included throughout regarding working on fuel system components.
Jcb 5 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing the backhoe loader models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The sample document focuses on servicing the crankshaft and main bearings of the engine. It provides details on lubrication, inspection procedures, removing and installing the crankshaft, installing new main bearing shells, checking clearances, and required torque specifications.
Jcb 4 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The document provides detailed procedures, diagrams, and specifications for maintenance, repairs, and inspections. Safety precautions are emphasized throughout requiring technicians to fully understand instructions before operating or servicing the machine.
Jcb 3 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing the backhoe loader models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The sample document focuses on servicing the crankshaft and main bearings of the engine. It provides details on lubrication, inspection procedures, removing and installing the crankshaft, installing new main bearing shells, checking clearances, and required torque specifications.
Daewoo doosan solar 175 lc v (di exp) crawler excavator parts catalogue manualdufjdjskkemm
This document provides a parts list and diagrams for components of a SOLAR 175LC-V engine, including the cylinder block, timing gear case, flywheel housing, crank shaft, cylinder head, and other parts. It lists over 50 individual parts with descriptions and identifies replacement parts. The parts list contains technical specifications like part numbers, quantities, serial numbers, and notes on replaceability.
Daewoo doosan solar 170 lc v (dieu exp) crawler excavator parts catalogue manualdufjdjskkemm
This document provides an exploded diagram and parts list for the valve mechanism of a SOLAR 170LC-V engine. It lists over 30 individual parts that make up the valve mechanism including inlet and exhaust valves, valve springs, retainers, rocker arms, rocker arm shaft assembly, and mounting brackets. Fasteners such as bolts, nuts, springs, and washers that hold the assembly together are also detailed.
Daewoo doosan solar 170 lc v (di exp) crawler excavator parts catalogue manualdufjdjskkemm
This document contains a parts list and diagrams for engine components of a Solar 170LC-V engine, including:
1. A cylinder block parts list with 52 items such as the cylinder block assembly, bearing caps, plugs, bolts, and liners.
2. A timing gear case diagram with 19 items like the timing gear case, cover, pins, and bolts.
3. A flywheel housing diagram with 16 items including the flywheel housing, bolts, washers, seal, and gasket.
4. A crankshaft diagram with over 30 items such as the crankshaft assembly, shaft, gear, bushings, connecting rods, bearings,
Caterpillar cat th417 c telehandler operator and maintenance manualdufjdjskkemm
This document provides an operation and maintenance manual for several models of JLG telehandlers. It contains important safety information and instructions for pre-operation inspection, operation of controls and indicators, and general safety practices. The manual should be kept with the machine at all times. Operators must be trained and qualified, and follow all safety guidelines. Contact JLG for any questions.
Caterpillar cat th406 c telehandler service repair manualdufjdjskkemm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information.
Caterpillar cat th337 c telehandler service repair manualdufjdjskkemm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information for the different systems.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...dufjdjskkemm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It outlines 37 steps to assemble bearings, seals, gears, carriers, retainers, shafts and other components. Precise torque specifications and clearance measurements are specified at various steps. Tools required include link brackets, drivers, spacer rings, seal installers and other implements to correctly position and install the components according to specifications.
More Related Content
Similar to Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up)
Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4...ufuusjejfjkse
1) The document provides instructions for separating, connecting, disassembling and assembling the track on a D6H track-type tractor.
2) Key steps include loosening the track tension, removing the master link and shoe, and using equipment to pull the track off. Reconnecting requires aligning the master link and tightening it to specification.
3) Disassembling the track involves removing pins and spreading links apart using tools, while assembling requires pressing bushings into links using a press and ensuring the seals are fully seated.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...fjskemedcdmme
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...jfksekksmem
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 r track type tractor (prefix 4hn) service repair manual (4...fujsjefjkskemm
1. The document provides instructions for disassembling and assembling the track on a D6R track-type tractor.
2. Key steps include separating the tracks by loosening bolts and releasing hydraulic pressure, then removing individual track links and pins.
3. Reassembly involves aligning the links and pins, lubricating fasteners, and adjusting track tension using hydraulic components. Precise sequences and specialized tools are required.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fujjdfjjskekmm
This document provides instructions for servicing the track on a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers, including using various tools to support the frame and align parts. The process ends by reconnecting the track.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fujdjjksekmem
This document provides instructions for servicing the track on a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers, including using various tools to support the frame and align parts. The process concludes by reconnecting the track.
Similar to Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up) (6)
Liebherr r964 c 1009 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 1008 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 448 hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r960 demolition 1465 hydraulic excavator service repair manualdufjdjskkemm
This document is a service manual that covers maintenance and repair for various systems of an industrial machine. It includes sections on technical data, maintenance procedures, drive systems, cooling systems, hydraulics, electrical systems, gearboxes, and other components. The manual provides instructions and specifications to service the machine.
Liebherr r934 c hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for maintenance and repairs.
2. Sections covering the engine, hydraulic and electrical systems, swing gear, track components and other parts.
3. Safety symbols and instructions for working on the machines.
The manual is intended to assist customer support but does not replace technical training. It includes schematics, diagrams and detailed views of machine units.
Jcb 10 tft dumper service repair manual sn from grn1313 to grn1313dufjdjskkemm
This service manual provides instructions for servicing the components of a dumper vehicle, including the machine body and framework, operator station, engine, fuel and exhaust system, cooling system, brake system, steering system, driveline, hydraulic system, electrical system, fasteners and fixings, and consumable products. The document provides detailed procedures for removing and installing parts like fuel pipes and injector bleed-off pipes, with accompanying diagrams and special tool requirements. Safety information is included throughout regarding working on fuel system components.
Jcb 5 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing the backhoe loader models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The sample document focuses on servicing the crankshaft and main bearings of the engine. It provides details on lubrication, inspection procedures, removing and installing the crankshaft, installing new main bearing shells, checking clearances, and required torque specifications.
Jcb 4 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The document provides detailed procedures, diagrams, and specifications for maintenance, repairs, and inspections. Safety precautions are emphasized throughout requiring technicians to fully understand instructions before operating or servicing the machine.
Jcb 3 cx backhoe loader service repair manual sn from 2254521 — 2274521dufjdjskkemm
This service manual provides instructions for servicing the backhoe loader models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The sample document focuses on servicing the crankshaft and main bearings of the engine. It provides details on lubrication, inspection procedures, removing and installing the crankshaft, installing new main bearing shells, checking clearances, and required torque specifications.
Daewoo doosan solar 175 lc v (di exp) crawler excavator parts catalogue manualdufjdjskkemm
This document provides a parts list and diagrams for components of a SOLAR 175LC-V engine, including the cylinder block, timing gear case, flywheel housing, crank shaft, cylinder head, and other parts. It lists over 50 individual parts with descriptions and identifies replacement parts. The parts list contains technical specifications like part numbers, quantities, serial numbers, and notes on replaceability.
Daewoo doosan solar 170 lc v (dieu exp) crawler excavator parts catalogue manualdufjdjskkemm
This document provides an exploded diagram and parts list for the valve mechanism of a SOLAR 170LC-V engine. It lists over 30 individual parts that make up the valve mechanism including inlet and exhaust valves, valve springs, retainers, rocker arms, rocker arm shaft assembly, and mounting brackets. Fasteners such as bolts, nuts, springs, and washers that hold the assembly together are also detailed.
Daewoo doosan solar 170 lc v (di exp) crawler excavator parts catalogue manualdufjdjskkemm
This document contains a parts list and diagrams for engine components of a Solar 170LC-V engine, including:
1. A cylinder block parts list with 52 items such as the cylinder block assembly, bearing caps, plugs, bolts, and liners.
2. A timing gear case diagram with 19 items like the timing gear case, cover, pins, and bolts.
3. A flywheel housing diagram with 16 items including the flywheel housing, bolts, washers, seal, and gasket.
4. A crankshaft diagram with over 30 items such as the crankshaft assembly, shaft, gear, bushings, connecting rods, bearings,
Caterpillar cat th417 c telehandler operator and maintenance manualdufjdjskkemm
This document provides an operation and maintenance manual for several models of JLG telehandlers. It contains important safety information and instructions for pre-operation inspection, operation of controls and indicators, and general safety practices. The manual should be kept with the machine at all times. Operators must be trained and qualified, and follow all safety guidelines. Contact JLG for any questions.
Caterpillar cat th406 c telehandler service repair manualdufjdjskkemm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information.
Caterpillar cat th337 c telehandler service repair manualdufjdjskkemm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information for the different systems.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...dufjdjskkemm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It outlines 37 steps to assemble bearings, seals, gears, carriers, retainers, shafts and other components. Precise torque specifications and clearance measurements are specified at various steps. Tools required include link brackets, drivers, spacer rings, seal installers and other implements to correctly position and install the components according to specifications.
Caterpillar cat d11 t track type tractor (prefix ama) service repair manual (...dufjdjskkemm
This document provides instructions for disassembling and assembling the torque converter of a D11T track-type tractor. It lists 50 steps for disassembly, including removing bolts, gears, seals, and other components. It then lists 27 steps for assembly, including pressing in bearings, installing seals and rings, and tightening bolts to the specified torques. Proper cleaning of parts and inspection for wear are emphasized throughout.
Caterpillar cat 135 h motor grader (prefix 7mm) service repair manual (7mm000...dufjdjskkemm
This document provides instructions for removing and installing various components of the power train system on 120H and 135H Motor Graders, including the parking brake, tandem drive housings, drive sprockets, and final drives. The instructions describe disconnecting transmission lines, draining oil, and removing/installing specific parts like housings, sprockets, seals and bolts using numbered steps and references to tools. Safety precautions are provided to release air pressure before disconnecting lines and avoid burns from hot oil.
Liebherr r906 1449 classic hydraulic excavator service repair manualdufjdjskkemm
The document is a service manual for Liebherr hydraulic excavators. It contains 18 sections that provide technical specifications, maintenance guidelines, and instructions for repairing and servicing various engine, hydraulic, electrical, and other components of the excavators. The manual is intended to assist customer support services and includes symbols to identify safety warnings and notes for procedures. It also provides guidelines for how the manual is structured and indexed.
Liebherr lh110 m 1227 (tier4f) hydraulic excavator service repair manualdufjdjskkemm
The document is a technical manual that discusses the mounting of standard and fine thread clamping nuts, and mounting clamping nuts on suspensions with swing brakes. It includes figures showing the components of differential cylinders and shock absorbers, and tables listing recommended corrosion inhibitors and base coats and paints from Liebherr. The manual instructs the reader to click on a link to access the complete manual.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6H TRACK-TYPE TRACTOR 4YF
Configuration: D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D6H TRACTOR POWER TRAIN
Media Number -SENR3242-03 Publication Date -01/11/2004 Date Updated -10/01/2017
SENR32420003
Track
SMCS - 4170-015; 4170-016; 4170-076; 4170-077
Separate Track
The machine must be on a level hard surface before a separation of the
track is made. Any time a separation of both tracks is made the
machine must have blocks correctly in position so the machine will not
move.
1. Remove track adjuster cover (1) and the O-ring seal from the roller frame.
The adjuster cylinder for the track is under high hydraulic pressure. Do
not visually inspect the relief valve to see if grease is released when it is
open. Look to see that the track has loosened. Use this warning any time
the tracks are loosened or tightened.
1/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Loosen the track as follows:
a. Turn the relief valve (2) one turn counterclockwise to permit grease to be released from the
track adjuster. If the track does not loosen go to Step b.
b. Turn fill valve (3) one turn counterclockwise to permit grease to be released from the track
adjuster. If the track still does not loosen, start the machine and move it forward and backward. If
grease is still not released go to Step c.
c. Install a piece of round bar stock between the bushing and sprocket inside the links. Move the
machine to the rear so the track will be pushed up by the round bar stock. This will put tension on
the track and move the track adjuster in.
3. Move the track until the master link is just above the centerline of rear idler (4). Put wood
blocks under the grouser bar, just below the master link. Move the track to the rear until it has
rigid contact with the wooden blocks.
4. The weight of the master shoe is from 19.5 kg to 37.5 kg (43 lbs to 825 lbs.), depending on
which track the vehicle is equipped. Remove four bolts (5) and master shoe (6).
5. Separate master link (7).
2/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Keep away from the front of the machine when the track is pushed off
of the final drive. A minimum distance of 6.1 m (20 ft) is needed in front
of the track to permit the track to move out on to the floor.
6. Fasten a chain to the end of the track and to a wheel loader, or similar machine. Turn the final
drive in a forward direction and let track (8) fall forward, as the wheel loader or similar machine is
moved forward.
7. The weight of the track is from 1676 kg to 2602 kg (3687 lbs. to 5724 lbs.) depending on
which track the machine has on it. Lift the side of the machine and remove the track if necessary.
Connect Track
1. Put the track under the machine. Lower the side of the machine on to track (8).
2. Fasten one end of a chain to track (8) and the other end to a wheel loader or similar machine.
NOTICE
To avoid damage to the track or to the machine, the track must be
pulled in a straight line.
3/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 3. Pull the track until the track bushings engage with the sprocket segments on the final drive.
4. Start the machine and turn the final drive in a reverse direction to pull the track together.
5. Lift the end of the track and put wooden blocks (9) under the grouser as shown.
NOTE: Make sure the serrations on the master link are free of loose or thick rust, paint, and
lubricants.
6. Align the lower end of master link (7) with the upper end of the master link. Make sure the teeth
of both ends of the master link are engaged.
7. Put track shoe (6) in position on the master link. Put 2P2506 Thread Lubricant on the threads,
body, and washer face of the master link bolts. Install bolts (5) that hold the master link together.
Tighten the bolts to a torque of 400 ± 70 N·m (300 ± 50 lb ft). Tighten the bolts an additional 1/3
of a turn. For inspection purposes, after assembly, the final torque must be a minimum of 680 N·m
(500 lb ft)
4/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 8. Tighten relief valve (2) and fill valve (3) in the track adjuster to a torque of 35 ± 7 N·m (25 ± 5
lb ft).
NOTICE
Measure the track (sag), distance from a straight line, when the
machine is in its working condition. If dirt and debris are present in its
working condition, then measure the (sag) when normal dirt and
debris are present in the track and its components.
9. Adjust the track tension as follows:
a. Move the machine forward for a distance that is two times the length of the machine. Let it
come to a stop without the use of the brakes.
b. Put a tight line between the grouser tips at the sprocket and front idler.
c. Measure distance (X) from the line to the lowest point of (sag) of the grouser tips. Put 5P960
Multipurpose Type Grease in the track adjuster and make an adjustment to the track until
distance (X) is 115 ± 10 mm (4.53 ± .40 in). This is the sag (curve) in the track between the
sprocket and the front idler.
5/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. d. Do not tighten the track more if distance (Y) is 150 mm (5.9 in) or more. The track will have to
be removed and reconditioned.
10. Install the track adjuster cover (1) and the O-ring seal onto the roller frame.
Disassemble Track
1. Put the track pin, to be removed, in position behind the front idler as shown.
2. Put blocks (2) in position under the front of the track.
3. Put blocks (3) in position under the track to keep the track away from the track roller frame
when the pressure is released in the track adjuster.
4. Release the pressure in the track adjuster. See topic, Separate Track.
6/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. 5. Put tool (A) in position as shown. Use tool (A) to keep the track in position when the track pins
are removed.
6. Remove the bolts, and use two persons to remove three track shoes (1) over the track pins to be
removed.
7. Fasten a hoist to tooling (B). Put tooling (B) in position against the track pin.
8. Push the track pin out of the track with tool (B), and install tool (C) to hold the track together
until the other track pin is removed.
9. Put tooling (B) in position against track pin (4). Push track pin (4) out of the track, and install
tool (C). Remove tooling (B) from the track.
10. Put tooling (D) in position between links (6) and (7). Use tooling (D) to spread the links apart
far enough to move link (5) away from links (6) and (7).
11. Remove tooling (C) from links (5), (6) and (7).
NOTICE
Use care when moving the links apart so the face of the seals are not
damaged.
12. Fasten a hoist to link (5). Move the link away from links (6) and (7).
7/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 13. Put a block under link (5) to keep it away from links (6) and (7).
14. Put tooling (D) in position between links (9) and (10). Use tooling (D) to spread the links apart
far enough to remove link assembly (8).
15. Fasten a hoist to link assembly (8).
16. Remove tool (C) from links (9) and (10) and link assembly (8), and remove the link assembly.
17. Remove seal assemblies (11) from the track links.
18. Put the track links and track bushing in position in tooling (E) as shown. Push the track
bushing from track link (6).
19. Put track link (7) and the track bushing in position in tooling (E). Remove the track bushing
from track link (7).
8/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 20. Use a punch and hammer, and remove plug (12) from stopper (13) in the track pins.
21. Remove stoppers (13) from the track pins.
Assemble Track
NOTE: Check all parts of the track assembly for wear or damage. Make replacements if
necessary. Make sure the parts are clean and dry before assembly.
9/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 1. Put 1P3482 Adapter (2) [part of tooling (A)] in frame (1) of the press arrangement [part of
tooling (A)] with the counterbore toward the ram as shown.
NOTICE
Use a maximum force of 760 kN (170 000 lb) when the track is
assembled. Excessive press force can cause damage to the thrust rings.
2. Put SAE 90 gear oil on each end of track bushing (4) for a minimum length of 5 mm (.197 in).
3. Use tooling (A), and install track bushing (4) into track link (3). Push the track bushing in until
it makes contact with tooling (A). The track bushing must extend 1.76 ± 0.13 mm (.069 ± .005 in)
above the surface of the track link.
4. Put track link (5), track bushing (4) and track link (3) in position in tooling (B). Install pin (6)
[part of tooling (B)] for alignment purposes. Use tooling (B), and install the track link on the track
bushing until the track bushing makes contact with tooling (B). The track bushing must extend
1.76 ± 0.13 mm (.069 ± .005 in) above the surface of the track link.
NOTICE
The seal assemblies must be completely sealed in the track link
counterbores. The load rings of the seal assemblies must make a
minimum amount of contact with oil. Oil causes the load rings to
expand. This is not desired until after assembly.
10/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) P...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. NOTICE
Make sure there is contact at area (X) between the seal and load ring.
5. Use tool (C) to install the seal assemblies (the seals and load rings) in the track links as shown
in illustration A82927P1.
6. Put oil on stoppers (7), and install them in track pins (8). The stoppers must be installed to a
depth of 8 ± 4 mm (.315 ± .157 in) below the surface of the track pins.
11/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) P...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 7. Put tooling (D) in position between the track links. Use tooling (D) to spread the links apart far
enough to install link assembly (9).
8. Fasten a hoist to link assembly (9). Put the link assembly in position, and install tooling (E) to
hold it in place.
9. Put tooling (D) in position between the links in link assembly (9). Use tooling (D) to spread the
links apart far enough to install link assembly (10).
10. Fasten a hoist to link assembly (10). Put the link assembly in position in link assembly (9).
11. Align the pin hole in link assembly (10) with the hole in link assembly (9), and install tool (E).
12. Fasten a hoist to tooling (F). Put tooling (F) and track pin (12) in position on the track links.
NOTE: The pin must be installed with the hole end on the same side of the track assembly for the
entire length of the track assembly. The oil cross hole in the pin must be within 20° of the vertical
centerline of the pin bore and closest to the rail of the link. The pins have a mark on the end for
cross hole location. Also, the pin must be installed with a minimum amount of force to get a
maximum amount of end play 0.13 mm (.005 in) between the bushing and the thrust ring.
13. Install track pin (12) with tooling (F) until the pin extends a maximum of 3.22 mm (.127 in)
beyond the link assembly on both sides.
12/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) P...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 14. Put track pin (11) and tooling (F) in position on the track links. Install track pin (11) until it
extends a maximum of 3.22 mm (.127 in) beyond the link assembly on both sides.
15. Use two persons, and put three track shoes (13) in position. Put 2P2506 Thread Lubricant on
the threads, body, and washer's face of the master link bolts. Install the track shoe bolts and nuts.
Make sure the radius corners of the nuts are away from the links. Tighten the bolts to a torque of
400 ± 70 N·m (300 ± 50 lb ft). Tighten the bolts 1/3turn more. For inspection purposes, after
assembly, the final torque must be a minimum of 680 N·m (500 lb ft).
16. Remove tooling (G).
17. Fill the track pins with a minimum of 50.0 mL (1.7 oz.) of SAE 90 gear oil.
18. Put oil on the plug, and install the plug in the stopper in the end of the track pin with tool (H).
Install the plug until it is even with the end of the stopper.
19. Adjust the track. See topic, Separate And Connect Track in this module for the adjustment
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 21:27:47 UTC+0800 2020
13/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) P...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6H TRACK-TYPE TRACTOR 4YF
Configuration: D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D6H TRACTOR POWER TRAIN
Media Number -SENR3242-03 Publication Date -01/11/2004 Date Updated -10/01/2017
SENR32420004
Sprocket Segments
SMCS - 4155-010
Remove And Install Sprocket Segments
1. Move the machine forward or backward until segment (2) to be removed, is in position as
shown.
2. Remove five bolts and nuts (1) and remove segment (2).
NOTE: The following steps are for installation of the sprocket segments.
3. Make sure the mating surfaces of the sprocket segment and the final drive are clean and free of
rust and scale.
NOTE: Install the segment so the head of the bolts are against the segment, and so the washers
and nuts (1) are against the final drive.
4. Put SAE 30 oil on the threads of the segment bolts. Put the segment in position on the final
drive and install bolts, washers, and nuts (1). Tighten nuts (1) to a torque of 175 ± 40 N·m (130 ±
30 lb ft). Tighten the nuts 1/3 of a turn more.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 21:28:37 UTC+0800 2020
1/1
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6H TRACK-TYPE TRACTOR 4YF
Configuration: D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D6H TRACTOR POWER TRAIN
Media Number -SENR3242-03 Publication Date -01/11/2004 Date Updated -10/01/2017
SENR32420005
Front Track Roller Frames
SMCS - 4151-011; 4151-012
Remove Front Track Roller Frames
Start By:
a. separate track
NOTE: The track roller frame does not have an oil drain plug. To avoid an oil spill when the front
track roller frame is removed from the rear track roller frame, use a vacuum pump in the opening,
near the track adjuster valve, to remove the oil. If a vacuum pump is not available, the oil will
drain when the front track roller frame is removed from the rear track roller frame.
1. Remove six bolts (1) and guide assembly (2) from each side of the rear track roller frame.
Remove the O-ring seal from each of the guide assemblies.
1/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. 2. Remove one bolt from each side of the front idlers and install tooling (A).
3. Attach one end of tooling (B) to tooling (A). Attach the other end of tooling (B) to a stationary
object. Use tooling (B) to pull the front track roller frame out of the rear track roller frame until
the bearing is free from the seal. Remove tooling (B).
4. The weight of the front track roller frame is 546 kg (1200 lb). Put a nylon strap (3) around the
front track roller frame and attach a hoist. Adjust the strap so the front track roller frame will be
level and remove it from the rear track roller frame.
5. Put the front track roller frame on blocks as shown. Use a torch and remove bearing (4) from
the front track roller frame if necessary.
6. Remove seal assembly (5), ring (6), and bearing (7) from the rear track roller frame.
2/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Install Front Track Roller Frame
1. If it is necessary to replace bearing (1), remove the track adjuster from the front track roller
frame. See Remove And Install Track Adjuster in this module for the proper procedure.
2. Put dry ice in the front track roller frame tube to lower the temperature of the tube. Heat bearing
(1) to a maximum temperature of 175° C (350° F). Install bearing (1) onto the front track roller
frame. Install the bearing so that it is a maximum of 1 mm (.039 in) away from the plate at the
front of the roller frame.
3. Install the track adjuster into the front track roller frame. See Remove And Install Track
Adjuster in this module for the proper procedure.
3/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 4. Install bearing (2) and ring (3) into the rear track roller frame.
NOTICE
Make sure tooling (A) and tooling (B) put pressure on the outer ring of
seal assembly (4) when they are used to install the seal assembly into
the rear track roller frame.
5. Put 7M7456 Bearing Mount on the outer diameter of seal assembly (4). Put seal assembly (4)
and tooling (A) in position in the rear track roller frame as shown.
6. Tighten the two nuts [part of tooling (A)] evenly and pull seal assembly (4) in until it is even
with the front surface of the rear track roller frame.
7. Use tool (B) and install seal assembly (4) to the bottom of the counterbore in the rear track
roller frame.
4/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. 8. Put seal guard [tooling (C)] in position on the inner diameter of seal assembly (4).
NOTICE
Use care to avoid causing damage to seal assembly (4) and bearing (2)
when the front track roller frame is installed.
9. Put SAE 30 oil on the outer diameter of the front track roller frame bearing (1).
10. Put a nylon strap around the front track roller frame. Adjust the nylon strap so the front track
roller frame is level. Put the front track roller frame into the rear track roller frame and allow
enough room to remove tooling (C). Remove tooling (C).
11. Install tooling (D) onto the rear track roller frame. Install tooling (E) onto the front track roller
frame. Attach the ratchet pullers [part of tooling (D)] to tooling (E).
12. Evenly, pull the front track roller frame into the rear track roller frame using tooling (D) and
(E). Make sure the grooves in the front track roller frame are aligned with the guide locations.
Remove tooling (D) and (E).
13. Install the bolts that hold the front idler caps and tighten them to a torque of 475 ± 50 N·m
(350 ± 37 lb ft).
5/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. NOTE: Install guide (5) on the inside of the rear track roller frame first for easier installation.
14. Make sure the guide slots are aligned. Apply Loctite 609 to the mating surface of guides (5)
and the track roller frames. Put guides (5) into the track roller frame and install the six bolts that
hold each one.
NOTE: The tracks must be installed and the correct track adjustment made before the oil level can
be checked in the recoil spring compartment.
15. Fill the recoil spring compartment with oil to the correct level. See the Operation And
Maintenance Guide for the type and capacity of oil to be used.
End By:
a. connect track
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 21:29:26 UTC+0800 2020
6/6
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6H TRACK-TYPE TRACTOR 4YF
Configuration: D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D6H TRACTOR POWER TRAIN
Media Number -SENR3242-03 Publication Date -01/11/2004 Date Updated -10/01/2017
SENR32420006
Recoil Springs
SMCS - 4158-011; 4158-012
Remove Recoil Springs
NOTE: All part numbers mentioned in this operation are part of tooling (A), (B), (C), or (D).
1/11
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...