The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Tools and safety precautions are also outlined. The overall purpose is to fully separate the governor into its main components to allow for inspection and replacement of worn parts.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fiskkdmdmdm
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fiskkdmdmdm
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
- The document provides instructions for disassembling a Type II Governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are advised to inspect all parts for wear and damage upon disassembly, replacing as needed according to specifications.
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fiskkdmdmdm
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fjjskkefksme
This document provides instructions for disassembling a Type II Governor used in Caterpillar 3114, 3116, and 3126 engines. The summary is:
1. The document outlines 54 steps to fully disassemble the governor, removing components like the cover, springs, flyweights, shutoff assembly, and throttle shaft.
2. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and other general shop tools.
3. Instructions emphasize cleaning and inspecting parts for wear or damage, and replacing worn components to ensure proper governor function.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fjkskmmdmme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fjjskkefksme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Kobelco SK250-8 (HS Engine) HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and safety precautions for repairing an excavator. It discusses general precautions for disassembling and assembling parts, handling hydraulic and electrical equipment, welding repairs, and international measurement units. The outline covers preparation before disassembling, safety when disassembling and assembling, procedures for hydraulic parts, and environmental considerations.
Kobelco SK85MSR-7 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document is a shop manual that provides guidelines and safety information for repairing and maintaining an excavator. It includes sections on general precautions, disassembling and assembling hydraulic equipment, electrical systems, and welding repairs. The manual is copyrighted by Kobelco Construction Machinery Co. and cannot be copied or distributed without permission. It is intended to instruct repair and maintenance of Kobelco excavators.
Kobelco SK130LC-11 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and general precautions for repairing a hydraulic excavator shop manual. It discusses the copyright of the manual, safety precautions for disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. Measurement units used are also described. The manual is intended solely for repair and maintenance of machines sold by Kobelco and cannot be copied, distributed or used for other purposes without permission.
Kobelco SK260LC-8 (HS Engine) HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and safety precautions for repairing an excavator. It discusses general precautions for disassembling and assembling parts, handling hydraulic and electrical equipment, welding repairs, and international measurement units. The outline covers preparation before disassembling, safety when disassembling and assembling, procedures for hydraulic and electrical parts, and environmental considerations. Measurement units and applicable machine models are also noted.
The document provides instructions for disassembling and assembling the service brake and final drive/wheel components of a Caterpillar 993K wheel loader. The disassembly procedure for the service brake involves removing reaction plates, discs, springs, pistons and seals. The assembly procedure specifies installing these components in reverse order while applying grease and torques. The final drive/wheel disassembly removes planetary carriers, gears, bushings, retainers and wheels. Tools and lifting devices are required due to component weights up to 1542 kg.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for assembling and disassembling components of the steering system on a 966K wheel loader. The steps include installing bearings and seals in the piston pump, removing and installing the secondary steering pump and electric motor, removing and installing the secondary steering control valve, and disassembling the secondary steering valve. The document contains diagrams to illustrate the proper order and orientation of parts. Safety precautions are provided for spring loaded components.
This document provides instructions for removing and installing various components of a Caterpillar 993K wheel loader engine, including:
1) Removing and reinstalling the rear power take-off (RPTO) which involves removing several nuts, bearings, and gears.
2) Removing and installing the vibration damper and pulley by removing bolts, spacers, and lifting the damper and pulley components.
3) Two separate procedures for removing and installing the vibration damper and pulley depending on the machine model, both involving removing bolts and lifting various damper and pulley components.
This document provides instructions for installing, removing, disassembling, and assembling a fuel ratio control system on a Caterpillar 3306 engine. It describes how to install and remove fuel injection nozzles and the fuel ratio control unit. The disassembly and assembly procedures explain how to take apart and rebuild the fuel ratio control unit, replacing worn parts.
This document provides instructions for disassembling the transmission of a 962M wheel loader. It lists over 50 steps to remove various transmission components including clutches, shafts, gears, bearings and seals. Safety precautions are provided for releasing spring forces. Required tools include lifting devices, presses and specialized compression tools. Detailed illustrations accompany each step to show the component locations.
This document provides the disassembly procedure for a piston pump used in 962L wheel loaders. It lists 26 steps to fully disassemble the pump and its components. Required tools include lifting eyes, threaded rods, eyebolts, drivers, depth gauges, and bearing pullers. Safety precautions are provided to properly release spring forces when removing springs. Pictures accompany each step to illustrate the process.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides assembly instructions for governors used on 3114, 3116, and 3126 engines. It describes 17 steps to assemble the governor, including installing various springs, levers, and other components. Key steps include installing the fuel ratio control lever assembly, output servo assembly, bearing block assembly, and adjusting the gap for the torque cam. The summary provides an overview of the major components and goal of assembling the governor.
More Related Content
Similar to Caterpillar Cat D250D ARTICULATED TRUCK (Prefix 6NG) Service Repair Manual (6NG00001 and up).pdf
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
- The document provides instructions for disassembling a Type II Governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are advised to inspect all parts for wear and damage upon disassembly, replacing as needed according to specifications.
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fiskkdmdmdm
- The document provides disassembly instructions for a Type II governor used in 3114, 3116, and 3126 engines.
- It describes removing over 30 individual parts in sequential order, including covers, seals, springs, flyweights, shafts, and other internal components.
- Technicians are instructed to inspect all parts for wear and damage, replacing as needed, to ensure proper reassembly and functioning of the governor.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fjjskkefksme
This document provides instructions for disassembling a Type II Governor used in Caterpillar 3114, 3116, and 3126 engines. The summary is:
1. The document outlines 54 steps to fully disassemble the governor, removing components like the cover, springs, flyweights, shutoff assembly, and throttle shaft.
2. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and other general shop tools.
3. Instructions emphasize cleaning and inspecting parts for wear or damage, and replacing worn components to ensure proper governor function.
Caterpillar cat d20 d articulated truck (prefix 9mg) service repair manual (9...fjkskmmdmme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fjjskkefksme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Similar to Caterpillar Cat D250D ARTICULATED TRUCK (Prefix 6NG) Service Repair Manual (6NG00001 and up).pdf (8)
Kobelco SK250-8 (HS Engine) HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and safety precautions for repairing an excavator. It discusses general precautions for disassembling and assembling parts, handling hydraulic and electrical equipment, welding repairs, and international measurement units. The outline covers preparation before disassembling, safety when disassembling and assembling, procedures for hydraulic parts, and environmental considerations.
Kobelco SK85MSR-7 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document is a shop manual that provides guidelines and safety information for repairing and maintaining an excavator. It includes sections on general precautions, disassembling and assembling hydraulic equipment, electrical systems, and welding repairs. The manual is copyrighted by Kobelco Construction Machinery Co. and cannot be copied or distributed without permission. It is intended to instruct repair and maintenance of Kobelco excavators.
Kobelco SK130LC-11 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and general precautions for repairing a hydraulic excavator shop manual. It discusses the copyright of the manual, safety precautions for disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. Measurement units used are also described. The manual is intended solely for repair and maintenance of machines sold by Kobelco and cannot be copied, distributed or used for other purposes without permission.
Kobelco SK260LC-8 (HS Engine) HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document provides an outline and safety precautions for repairing an excavator. It discusses general precautions for disassembling and assembling parts, handling hydraulic and electrical equipment, welding repairs, and international measurement units. The outline covers preparation before disassembling, safety when disassembling and assembling, procedures for hydraulic and electrical parts, and environmental considerations. Measurement units and applicable machine models are also noted.
The document provides instructions for disassembling and assembling the service brake and final drive/wheel components of a Caterpillar 993K wheel loader. The disassembly procedure for the service brake involves removing reaction plates, discs, springs, pistons and seals. The assembly procedure specifies installing these components in reverse order while applying grease and torques. The final drive/wheel disassembly removes planetary carriers, gears, bushings, retainers and wheels. Tools and lifting devices are required due to component weights up to 1542 kg.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for assembling and disassembling components of the steering system on a 966K wheel loader. The steps include installing bearings and seals in the piston pump, removing and installing the secondary steering pump and electric motor, removing and installing the secondary steering control valve, and disassembling the secondary steering valve. The document contains diagrams to illustrate the proper order and orientation of parts. Safety precautions are provided for spring loaded components.
This document provides instructions for removing and installing various components of a Caterpillar 993K wheel loader engine, including:
1) Removing and reinstalling the rear power take-off (RPTO) which involves removing several nuts, bearings, and gears.
2) Removing and installing the vibration damper and pulley by removing bolts, spacers, and lifting the damper and pulley components.
3) Two separate procedures for removing and installing the vibration damper and pulley depending on the machine model, both involving removing bolts and lifting various damper and pulley components.
This document provides instructions for installing, removing, disassembling, and assembling a fuel ratio control system on a Caterpillar 3306 engine. It describes how to install and remove fuel injection nozzles and the fuel ratio control unit. The disassembly and assembly procedures explain how to take apart and rebuild the fuel ratio control unit, replacing worn parts.
This document provides instructions for disassembling the transmission of a 962M wheel loader. It lists over 50 steps to remove various transmission components including clutches, shafts, gears, bearings and seals. Safety precautions are provided for releasing spring forces. Required tools include lifting devices, presses and specialized compression tools. Detailed illustrations accompany each step to show the component locations.
This document provides the disassembly procedure for a piston pump used in 962L wheel loaders. It lists 26 steps to fully disassemble the pump and its components. Required tools include lifting eyes, threaded rods, eyebolts, drivers, depth gauges, and bearing pullers. Safety precautions are provided to properly release spring forces when removing springs. Pictures accompany each step to illustrate the process.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides assembly instructions for governors used on 3114, 3116, and 3126 engines. It describes 17 steps to assemble the governor, including installing various springs, levers, and other components. Key steps include installing the fuel ratio control lever assembly, output servo assembly, bearing block assembly, and adjusting the gap for the torque cam. The summary provides an overview of the major components and goal of assembling the governor.
This document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It outlines 35 steps to disassemble the various components, including removing bolts, gears, bearings, seals and housing pieces. It then lists 12 steps for reassembling the components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools and torque specifications are provided for relevant steps.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 59 assembly steps and includes illustrations of each step. The key components assembled are the input shaft, planetary gears, carrier assemblies, ring gears, output shaft, clutch plates and discs, seals, and housing. Cleanliness is emphasized and special tools are required for some steps like installing retaining rings and bearings.
Caterpillar Cat 950F SERIES II WHEEL LOADER (Prefix 4DJ) Service Repair Manua...f8uuseijdkmd3e
This document provides instructions for disassembling a Type IV governor used in Caterpillar 3114, 3116, and 3126 engines. It outlines 39 steps to disassemble the governor into its main components. Required tools include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and other standard shop tools. Cautions are provided regarding spring forces and containment of fluids.
Kobelco SK350LC-10 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document is a shop manual that contains specifications, maintenance, system, disassembly, troubleshooting, and engine sections for hydraulic excavator models SK330-10 and SK350LC-10. It provides safety information and precautions for operating and servicing the excavators. The manual outlines general safety messages and contains warnings for working on pressurized systems, lifting heavy components, hot parts, and ensuring all guards are in place before starting work.
Kobelco SK330-10 HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document outlines general precautions and guidelines for repairing excavator shop manuals. It discusses copyright of the manual, safety procedures, hydraulic and electrical equipment, welding repairs, and international unit systems. Precautions include preparing the work area, using proper safety equipment, relieving pressures, blocking components, and handling hazardous materials. The manual is intended to instruct repair, maintenance, and adjustments of machines sold by Kobelco.
Kobelco SK230SRLC-5E HYDRAULIC EXCAVATOR Service Repair Manual.pdff8uuseijdkmd3e
This document is a shop manual that provides specifications, maintenance, system, disassembly, and troubleshooting information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and installing options. The document provides important safety information that should be read and understood before working on the excavator.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D250D ARTICULATED TRUCK 6NG
Configuration: D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
3114, 3116 and 3126 MUI Engine Governors
Media Number -SENR6454-05 Publication Date -01/02/2002 Date Updated -01/03/2002
i01017300
Governor (Type I) - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7307 Governor Repair Fixture (1)
1
B 1P-1855 Retaining Ring Pliers 1
C 1P-1857 Retaining Ring Pliers 1
D 1U-7606 Servo Block (1)
1
E 1U-7277 Pin Punch 1
F 1U-7635 Clevis Driver (1)
1
( 1 )
Part of former 1U-9088 Governor Tool Group
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Inspect all parts of the governor upon disassembly. For information on the reusability of
components in the governor, refer to the Guideline For Reusable Parts And Salvage Operations,
SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups
Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". For
information on cleaning the components in the governor, refer to the Cleaning Guide, SEBF8354,
"Equipment And Chemical Recommendations Reference Manual".
Note: Refer to Chart A "Parts to be Replaced During Rebuild" in Guideline For Reusable Parts
And Salvage Operations, SEBF8434 for a list of components that need to be replaced during a
governor rebuild. It is not necessary to replace the components in Chart A "Parts to be Replaced
During Rebuild" if the governor is in the shop for a bench test or for minor repair.
Note: Early Type I Governors had limited production until 1991. The early Type I Governors may
be inspected and perhaps reconditioned. However, some of the internal components are no longer
serviced or the internal components may only be serviced by larger assemblies. When you
recondition a Type I Governor, it may be necessary to replace the governor. If extensive repair
work is necessary, a Type I Governor can be replaced with a Type IV Governor.
2/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00521797
Typical Governor
(1) Bolt
(2) Orifice for the dashpot
(3) O-ring seal
(4) Bolt
(5) Cover
(6) Cover assembly
(7) O-ring seal
3/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. (8) Shims
(9) Rear spring seat
(10) Retaining ring
(11) Spacer
(12) Piston assembly for the dashpot
(13) Shims for the high idle governor (if equipped)
(14) Spring pair
(15) Spring seat assembly
1. Mount the drive gear end of the governor on the 1U-7307 Governor Repair Fixture (Tool
(A) ).
Illustration 2 g00521798
2. Remove three bolts (4) .
3. Remove cover (5) .
Illustration 3 g00521800
4/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Remove O-ring seal (3) from cover (5). Inspect the O-ring seal for wear or damage. If the O
-ring seal is worn or damaged, use a new part for replacement.
Illustration 4 g00521801
5. Ensure that orifice (2) for the dashpot is not plugged. Also ensure that orifice (2) is tight in
the casting.
Note: The orifice for the dashpot may be drilled directly into the governor rear housing or
the orifice may be a fitting that is staked into the governor rear housing. Ensure that all
orifice fittings are staked into the governor housing before reassembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6. Use the following procedure in order to remove cover assembly (6) .
a. Hold cover assembly (6) in position and slowly loosen bolts (1) in order to release the
spring force.
b. Remove three bolts (1) from the cover assembly.
c. Remove cover assembly (6) .
5/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g00521802
7. Remove O-ring seal (7) from cover assembly (6). Inspect the O-ring seal for wear or
damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Illustration 6 g00521803
8. Remove rear spring seat assembly (9) .
Illustration 7 g00522509
6/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 9. Remove spacer (11). Remove shims (8) from governor spring seat (9), if equipped. inspect
governor spring seat (9) for wear or damage.
Illustration 8 g00522514
10. Remove shims (13) for the high idle governor, if equipped.
Illustration 9 g00522516
11. Remove spring seat assembly (15) from the governor.
7/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g00522517
Illustration 11 g00522519
Note: Spring pair (14) can be removed by unscrewing the coils of the springs from spring
seat assembly (15). Inspect the spring pair for wear or damage. Replace the spring pair as a
spring group package only. The dashpot spring (if equipped) does not need to be replaced as
part of the governor spring package.
Illustration 12 g00522532
8/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 12. Remove six bolts (16) in order to separate governor rear housing (17) from governor front
housing (18) .
Note: Steps 13 through 35 are for the disassembly of the governor front housing. Steps 36
through 56 are for the disassembly of the governor rear housing.
Illustration 13 g00522534
13. Remove riser (19) from governor front housing (18) .
Illustration 14 g00522535
14. Remove retaining ring (20), two races (21), bearing (23) and shims (22) from riser (19) .
9/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED ...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 15 g00522536
15. Remove four bolts and four washers (24) that hold the flyweights in position.
Illustration 16 g00522537
16. Remove flyweights (25) .
Illustration 17 g00522574
10/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 18 g00522576
17. Remove flyweight pin (26). Inspect the pin for wear or damage.
18. Remove flyweight (25) from flyweight toe (27). Inspect the flyweight and the flyweight toe
for wear or damage. If the flyweight or the flyweight toe is damaged, use new parts for
replacement.
Note: Keep all parts of each flyweight together for assembly.
Illustration 19 g00522577
19. Hold flyweight carrier (28) in order to prevent the flyweight carrier from rotating and
remove eight carrier bolts (29) .
Note: Upon assembly, do not reuse eight carrier bolts (29). Replace the used carrier bolts
with new carrier bolts.
11/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 20 g00522581
20. Remove flyweight carrier (28) and riser shaft (30) from the governor front housing.
Illustration 21 g00522582
21. Remove pin (31) from riser shaft (30). Remove riser shaft (30) from flyweight carrier (28).
Inspect riser shaft (30) for wear or damage. If the riser shaft is worn or damaged, use a new
part for replacement. Inspect pin (31) for wear or damage. If the pin is worn or damaged,
use a new part for replacement.
12/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 22 g00522819
Note: Two types of shutoff assemblies are used. The first type was used on Types I, II, and
III governors. The second type has a spring that is preloaded in the opposite direction. This
is the bias spring.
22. Remove two bolts (32) and the washers.
23. Remove shutoff assembly (33). Inspect the shutoff assembly for wear or damage. If the
shutoff assembly is worn or damaged, use new parts for replacement.
Illustration 23 g00522821
24. If necessary, remove blade (34) and blade (36). Do not remove spring (35) .
Illustration 24 g00522822
25. Remove spring (38) for the throttle lever from throttle shaft (37) .
13/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 25 g00522823
26. Remove retaining clip (39) from throttle shaft (37) .
Illustration 26 g00522826
27. Remove spacer (43), spring (42), setscrew (41), and control lever (40) from throttle shaft
(37) .
Illustration 27 g00522898
14/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 28. Remove retaining clip (44) from throttle shaft (37) .
Illustration 28 g00522900
29. Remove throttle shaft (37) from the governor front housing. Inspect the throttle shaft for
wear or damage. If the throttle shaft is worn or damaged, use a new part for replacement.
Illustration 29 g00522902
30. Inspect throttle shaft seal (45) carefully for wear or damage. If the throttle shaft seal is worn
or damaged, use a new part for replacement.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 30 g00522904
31. Use the following procedure in order to remove cover assembly (47) .
a. Hold cover assembly (47) in position and slowly loosen bolts (46) in order to release
the spring force.
b. Remove three bolts (46) and cover (47) .
Illustration 31 g00522905
32. Remove spring (48) and O-ring (49). Inspect the O-ring for wear or damage. If the O-ring is
worn or damaged, use a new part for replacement.
16/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 32 g00522950
33. Remove sleeve assembly (50) and tappet assembly (51) from the governor front housing.
Illustration 33 g00522951
34. Remove piston (52) from sleeve assembly (50). Inspect the condition of piston (52) and
sleeve assembly (50). If the piston or the sleeve assembly are worn or damaged, use new
parts for replacement.
Illustration 34 g00522952
17/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 35. Remove lower O-ring seal (53) from the fuel transfer pump housing. Check the O-ring seal
for wear or damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Note: Remove the governor front housing from the 1U-7307 Governor Repair Fixture (Tool
(A) ).
Illustration 35 g00522953
36. Install three legs (G) on the 1U-7307 Governor Repair Fixture (Tool (A) ). Mount the
governor rear housing on the three legs.
37. Remove seal (54) from the governor rear housing. Inspect the seal for damage. If the seal is
damaged, use a new part for replacement.
Illustration 36 g00522954
NOTICE
The position of the bearing block will affect the output of the fuel rack.
If the bearing block assembly is positioned too close to the riser lever,
high idle may not be reached. If the bearing block assembly is
18/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. positioned too far from the riser lever, fuel shutoff may not be
obtained.
Note: Use a scribe to mark the location of the bearing block on the aluminum housing near
the hole for the fuel shutoff solenoid. Scribe marks (X) should indicate the vertical position
of the bearing block and the horizontal position of the bearing block. Scribe the marks close
to the bearing block.
38. Remove two bolts (55) and the washers. Remove bearing block (56) .
Illustration 37 g00523003
39. Use Tool (B) to remove retaining ring (58). Loosen bolt (57). Remove riser lever (59) from
bearing block assembly (56) .
Illustration 38 g00523005
40. Remove bearing block assembly (56) from pivot shaft (60) .
19/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 39 g00523007
41. Remove adjuster (63) for the torque cam from pivot shaft (60). Remove torsion spring (62)
from pivot shaft (60). Inspect the condition of the parts on pivot shaft (60). If any of the
parts are worn or damaged, use new parts for replacement.
42. Remove fulcrum lever (61) from pivot shaft (60). Remove the spring from the end of pivot
shaft (60) .
Illustration 40 g00523008
43. Push limit sleeve (66) and control sleeve (64) toward each other and compress spring (65) in
order to expose retaining clip (67). Remove retaining clip (67) from governor output servo
(68). Inspect the parts of the servo assembly for wear or damage.
20/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 41 g00523033
44. Remove retaining ring (69) with Tool (C). Remove governor output servo assembly (68) by
pulling out on the clevis.
Note: Limit sleeve (66), spring (65), and control sleeve (64) will come out of the governor
housing when the governor output servo assembly is removed.
Illustration 42 g00523034
Governor Output Servo (Earlier Style)
(70) Sleeve
(71) Servo piston
(72) Servo Valve
(73) Clevis
(74) Spring pin
(75) O-ring seal
21/29
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERE...
2020/2/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...