This document provides instructions for removing and installing the front gear group on a Caterpillar 3412E engine. It describes:
1. Aligning timing marks and removing the idler gear, bearing, thrust washer, and shaft.
2. Cleaning and installing the shaft, washer, bearing, and idler gear while aligning timing marks.
3. The procedure is accompanied by illustrations and notes on required tools.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torque specifications are provided for reinstallation.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torque specifications are provided for reinstallation.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, and valve mechanism cover of a Caterpillar 3412E engine. The removal procedures include aligning timing marks, removing bolts and gears, while taking care to contain fluids. The installation procedures specify cleaning parts, applying sealant, aligning timing marks, and torquing bolts to the specified values. Tools and torque specifications are provided where needed.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torque specifications are provided for reinstallation.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torque specifications are provided for reinstallation.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing various components of the front gear group, front housing, and valve mechanism cover of a Caterpillar 3412E engine. The removal procedures include aligning timing marks, removing bolts and gears, while taking care to contain fluids. The installation procedures specify cleaning parts, applying sealant, aligning timing marks, and torquing bolts to the specified values. Tools and torque specifications are provided where needed.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
Caterpillar cat 312 d excavator (prefix hjx) service repair manual (hjx00001 ...ikdkdmdm
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It outlines 20 steps to assemble the pump components in the proper order, attaching seals, bearings, gears, and covers. The final step is to install the assembled axle oil cooler pump and clutch. A second section then provides directions to install the assembled pump and clutch unit onto mounting brackets on the vehicle.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It outlines 20 steps to assemble the pump components in the proper order, attaching seals, bearings, gears, and covers. The final step is to install the assembled axle oil cooler pump and clutch. A second section then provides directions to install the assembled pump and clutch unit onto mounting brackets on the vehicle.
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1) Procedures for assembling the gear pump for the axle oil cooler, which involves installing various seals, bearings, gears, and retaining rings.
2) Instructions for installing the axle oil cooler pump and clutch, such as connecting components with bolts and installing a belt.
3) Steps for removing and installing the fuel filter base, like disconnecting hoses and harness and removing/installing bolts.
4) The start of instructions for removing the fuel transfer pump, including mounting the unit injector hydraulic pump vertically on a work
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1. Instructions for removing and installing the gear pump for the axle oil cooler, which involves cleaning parts, installing seals and bearings, and securing with retaining rings.
2. Instructions for installing the axle oil cooler pump and clutch, which involves connecting components with bolts and belts.
3. Instructions for removing and installing the fuel filter base, which involves disconnecting hoses and harnesses and securing the base with bolts.
Caterpillar cat 950 h wheel loader (prefix jad) service repair manual (jad000...dikdkskmmdm
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1) Procedures for assembling the gear pump for the axle oil cooler, which involves installing various seals, bearings, gears, and retaining rings.
2) Instructions for installing the axle oil cooler pump and clutch, such as connecting components with bolts and installing a belt.
3) Steps for removing and installing the fuel filter base, like disconnecting hoses and harness and removing/installing bolts.
4) The start of instructions for removing the fuel transfer pump, including mounting the unit injector hydraulic pump vertically on a work
Caterpillar cat 950 h wheel loader (prefix jad) service repair manual (jad000...fjjskkemsmee
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1. Instructions for removing and installing the gear pump for the axle oil cooler, which involves cleaning parts, installing seals and bearings, and securing with retaining rings.
2. Instructions for installing the axle oil cooler pump and clutch, which involves connecting components with bolts and belts.
3. Instructions for removing and installing the fuel filter base, which involves disconnecting hoses and harnesses and securing the base with bolts.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It lists the required tools and 20 steps for installing seals, bearings, gears, shafts, and other components into the gear pump body and cover. It also provides instructions for installing the axle oil cooler pump and clutch, including connecting hoses, belts, and brackets. Finally, it summarizes removing and installing the fuel transfer pump from the unit injector hydraulic pump. The instructions include cleaning parts, torquing bolts, and maintaining component alignment.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists 57 steps to fully disassemble the torque converter and its components. The steps include removing pumps, gears, seals, housings, and other internal parts. Special tools are required for separating some components. Precautions are given to handle parts carefully due to their weights ranging from 25 to 680 kg. Cleanliness is stressed to prevent contaminating precision parts during disassembly.
This service repair manual provides instructions for disassembling and assembling the torque converter of a 992K Wheel Loader. It lists over 60 steps to remove components such as the torque converter, transmission pump, gear assemblies, discs, seals and bearings. Detailed illustrations accompany each step and special tools are required to remove some heavy components weighing over 100 kg. The manual is intended to guide technicians in properly servicing the power train of the wheel loader.
More Related Content
Similar to Caterpillar Cat 992C WHEEL LOADER (Prefix 42X) Service Repair Manual (42X00001 and up).pdf
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
Caterpillar cat 312 d excavator (prefix hjx) service repair manual (hjx00001 ...ikdkdmdm
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, loosening bolts in a specific sequence, lifting the cylinder head off using a device, and installing the new head and gaskets in the reverse order. Tools and safety precautions are listed to properly complete the procedure.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine. It describes disconnecting hoses and tubes, removing bolts in a specified sequence, and lifting the cylinder head off using a lifting device due to its weight of approximately 80 kg. The installation procedure specifies cleaning parts and installing the cylinder head and bolts in the reverse order of removal.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It outlines 20 steps to assemble the pump components in the proper order, attaching seals, bearings, gears, and covers. The final step is to install the assembled axle oil cooler pump and clutch. A second section then provides directions to install the assembled pump and clutch unit onto mounting brackets on the vehicle.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It outlines 20 steps to assemble the pump components in the proper order, attaching seals, bearings, gears, and covers. The final step is to install the assembled axle oil cooler pump and clutch. A second section then provides directions to install the assembled pump and clutch unit onto mounting brackets on the vehicle.
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1) Procedures for assembling the gear pump for the axle oil cooler, which involves installing various seals, bearings, gears, and retaining rings.
2) Instructions for installing the axle oil cooler pump and clutch, such as connecting components with bolts and installing a belt.
3) Steps for removing and installing the fuel filter base, like disconnecting hoses and harness and removing/installing bolts.
4) The start of instructions for removing the fuel transfer pump, including mounting the unit injector hydraulic pump vertically on a work
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1. Instructions for removing and installing the gear pump for the axle oil cooler, which involves cleaning parts, installing seals and bearings, and securing with retaining rings.
2. Instructions for installing the axle oil cooler pump and clutch, which involves connecting components with bolts and belts.
3. Instructions for removing and installing the fuel filter base, which involves disconnecting hoses and harnesses and securing the base with bolts.
Caterpillar cat 950 h wheel loader (prefix jad) service repair manual (jad000...dikdkskmmdm
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1) Procedures for assembling the gear pump for the axle oil cooler, which involves installing various seals, bearings, gears, and retaining rings.
2) Instructions for installing the axle oil cooler pump and clutch, such as connecting components with bolts and installing a belt.
3) Steps for removing and installing the fuel filter base, like disconnecting hoses and harness and removing/installing bolts.
4) The start of instructions for removing the fuel transfer pump, including mounting the unit injector hydraulic pump vertically on a work
Caterpillar cat 950 h wheel loader (prefix jad) service repair manual (jad000...fjjskkemsmee
This document provides instructions for servicing components of a Caterpillar 950H wheel loader powered by a C7 engine, including:
1. Instructions for removing and installing the gear pump for the axle oil cooler, which involves cleaning parts, installing seals and bearings, and securing with retaining rings.
2. Instructions for installing the axle oil cooler pump and clutch, which involves connecting components with bolts and belts.
3. Instructions for removing and installing the fuel filter base, which involves disconnecting hoses and harnesses and securing the base with bolts.
The document provides instructions for installing the gear pump for an axle oil cooler on a 950H wheel loader. It lists the required tools and 20 steps for installing seals, bearings, gears, shafts, and other components into the gear pump body and cover. It also provides instructions for installing the axle oil cooler pump and clutch, including connecting hoses, belts, and brackets. Finally, it summarizes removing and installing the fuel transfer pump from the unit injector hydraulic pump. The instructions include cleaning parts, torquing bolts, and maintaining component alignment.
Similar to Caterpillar Cat 992C WHEEL LOADER (Prefix 42X) Service Repair Manual (42X00001 and up).pdf (20)
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists 57 steps to fully disassemble the torque converter and its components. The steps include removing pumps, gears, seals, housings, and other internal parts. Special tools are required for separating some components. Precautions are given to handle parts carefully due to their weights ranging from 25 to 680 kg. Cleanliness is stressed to prevent contaminating precision parts during disassembly.
This service repair manual provides instructions for disassembling and assembling the torque converter of a 992K Wheel Loader. It lists over 60 steps to remove components such as the torque converter, transmission pump, gear assemblies, discs, seals and bearings. Detailed illustrations accompany each step and special tools are required to remove some heavy components weighing over 100 kg. The manual is intended to guide technicians in properly servicing the power train of the wheel loader.
This service manual provides instructions for assembling the torque converter for a 988K wheel loader. It outlines 92 steps to install various components like seals, bearings, gears, and housing parts. Precision and cleanliness are important during assembly. Tools are required to measure clearances and set components. The manual includes illustrations pointing to each part mentioned in the assembly process.
This document provides instructions for assembling and disassembling parts of a 982M wheel loader transmission. It describes 51 steps to assemble the torque converter. It then describes 5 steps to separate the transmission from the output transfer gears, including using lifting equipment to position components and removing bolts, harnesses and tubes. The document provides illustrations and lists required tools for each procedure.
This document provides disassembly and assembly instructions for the lock up clutch with freewheel stator on a 980K wheel loader power train. It includes 46 steps to disassemble components such as the torque converter housing, pump adapter, idler gear, shaft assembly, impeller, and stator. It also includes 18 steps for assembly, including installing seals, bearings, plates, rings, and other components in the reverse order of disassembly. Required tools including link brackets, driver groups, and retaining ring pliers are listed. Cleanliness during assembly is emphasized.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides instructions for disassembling and assembling a torque converter for a 972H wheel loader. The disassembly procedure involves removing over 30 individual parts from the torque converter housing in a specific sequence. The assembly procedure instructs technicians to thoroughly clean all parts and install components in the reverse order of disassembly while following torque specifications. Special tools are required and cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms.
This document provides instructions for disassembling and assembling the torque converter and its components for a 972H Wheel Loader. It begins with required tools and safety notices. The disassembly steps include removing the torque converter housing, impeller, stator, carrier shaft, and other internal parts. The assembly section instructs installing the components in reverse order and notes that cleanliness is important. Torque specifications and the use of new replacement parts for any that are worn or damaged are also specified.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Caterpillar Cat 992C WHEEL LOADER (Prefix 42X) Service Repair Manual (42X00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02160179
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00577213
1. Align the timing mark on the idler gear with the timing mark on the crankshaft gear.
2. Remove bolts (1) and plate (2).
3. Remove idler gear (3).
Illustration 2 g00577286
4. Remove the bearing from idler gear (3) with Tooling (A) and a suitable press.
2/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 3 g00577251
5. Remove thrust washer (6). Remove bolts (4) and shaft (5).
Illustration 4 g00577274
6. Drilled passage (7) and drilled passage (8) in the shaft must be free of obstructions.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:41:18 UTC+0800 2021
3/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02151029
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00577251
Illustration 2 g00537659
1. Place shaft (5) in position on the cylinder block and install bolts (4). Tighten bolts (4) to a
torque of 55 ± 10 N·m (41 ± 7 lb ft).
Tighten bolts (4) for the shaft in the following sequence. See Illustration 2 for the
numbering of the bolts. ... 1,3,4,5,2,1,2,3,4,5,1
2. Install thrust washer (6) with the oil groove side toward the idler gear.
Illustration 3 g00577286
3. Lower the temperature of the bearing. Install the bearing in idler gear (3) with Tooling (A)
and a suitable press. Install the bearing to a depth of 0.38 ± 0.25 mm (0.015 ± 0.010 inch).
2/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 4 g00577213
4. Apply clean engine oil to the shaft and to the inside diameter of idler gear (3). Install idler
gear (3) on the shaft. Install plate (2) and bolts (1).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:42:15 UTC+0800 2021
3/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02389879
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
d. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
e. Remove the speed/timing sensors. Refer to Disassembly and Assembly, "Speed/Timing
Sensor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00553958
1. Remove bolts (2) and retainer plate (3).
2. Remove gear (1).
Illustration 2 g00553982
3. Attach Tooling (A) and a suitable lifting device to front housing (4). The weight of front
housing (4) is approximately 34 kg (75 lb).
4. Remove nut (6).
5. Remove bolts (5).
6. Remove front housing (4) and the gasket.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:43:11 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02389888
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B 8T-9022 Silicone Gasket -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00553982
1. The rear of front housing (4) and the front of the cylinder block should be thoroughly
cleaned before you install the front housing.
2. Install a new gasket on the cylinder block.
3. Apply Tooling (B) to the common junction of the cylinder block, the front housing and the
oil pan.
4. Attach Tooling (A) and a suitable lifting device to front housing (4). The weight of front
housing (4) is approximately 34 kg (75 lb).
5. Install front housing (4) on the cylinder block.
6. Install bolts (5).
7. Install nut (6).
8. Remove Tooling (A) from front housing (4).
Illustration 2 g00553958
2/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00555906
Note: With the number one piston of the engine at top center, the timing marks on the front
gear group can be aligned. Align the timing marks on gear (1) with the marks on the
camshaft gear. The alignment of the timing marks is shown in Illustration 3.
9. Install gear (1) and retainer plate (3).
10. Install bolts (2). Tighten the bolts to a torque of 135 ± 20 N·m (100 ± 15 lb ft).
End By:
a. Install the speed/timing sensors. Refer to Disassembly and Assembly, "Speed/Timing
Sensor - Remove and Install".
b. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
c. Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Install".
d. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
e. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:44:08 UTC+0800 2021
3/3
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02389917
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01095551
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 1. Remove bolts (2).
2. Remove cover (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01095551
1. Install cover (1).
2. Install bolts (2).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:45:05 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02160475
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01095563
1. Disconnect harness assembly (3).
2. Disconnect harness assemblies (5).
3. Remove bolt (4).
4. Remove bolts (1).
5. Remove base (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01095563
1. Install base (2).
2. Install bolts (1).
3. Install bolt (4).
Note: Each harness assembly has a white connector that is marked "F" (front) and a black
connector that is marked "R" (rear). The white connector must be installed on the injector
toward the front of the engine. The black connector must be installed on the injector toward
the rear of the engine.
Note: The black connector is marked "R" (rear). Assemble the black connector to the
injector on the rear cylinder. The rear cylinders are 3, 7, and 11 on the left side of the
engine. The rear cylinders are 4, 8, and 12 on the right side of the engine.
4. Place harness assemblies (5) on the connectors. Tighten the nuts on harness assemblies (5)
to the following torque.
Torque for nuts ... 1.70 ± 0.25 N·m (15.046 ± 2.213 lb in)
5. Connect harness assembly (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
3/4
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02160605
Rocker Arm and Shaft - Remove
SMCS - 1102-011
Removal Procedure
Start By:
a. Remove the unit injector. Refer to Disassembly and Assembly, "Unit Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01095626
1. Remove bolt (2) and cylinder head bolt (1).
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 2. Remove rocker arm assembly (3) and the O-ring seal.
3. Remove the pushrods.
4. Remove valve bridges (4).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:46:58 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02160625
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Start By:
a. Remove the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01095707
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 1. Remove retaining rings (1), washers (2), and arm assemblies (3) from shaft (4).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:47:55 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02161072
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01095707
1. Lubricate shaft (4) with clean engine oil and install arm assemblies (3).
2. Install washers (2).
3. Install retaining rings (1).
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. End By:
a. Install the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:48:52 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02161082
Rocker Arm and Shaft - Install
SMCS - 1102-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01095626
1. Lubricate the wear pad on top of valve bridges (4) with clean engine oil. Install valve
bridges (4).
2. Install the pushrods.
1/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
27. 3. Install the O-ring seal and rocker arm assembly (3).
4. Install cylinder head bolt (1) and bolt (2). Do not tighten bolt (2) at this time.
5. Tighten cylinder head bolt (1) to a torque of 270 ± 15 N·m (199 ± 11 lb ft). Tighten cylinder
head bolt (1) again to a torque of 450 ± 15 N·m (332 ± 11 lb ft). Tighten cylinder head bolt
(1) again to a torque of 450 ± 15 N·m (332 ± 11 lb ft). Tighten bolt (2) to the standard
torque value.
End By:
a. Install the unit injector. Refer to Disassembly and Assembly, "Unit Injector - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 24 09:49:49 UTC+0800 2021
2/2
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992C WHEEL LOADER 42X
Configuration: 992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i02184090
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 5P-8700 Lifting Bracket 2
Start By:
a. Remove the unit injector sleeves. Refer to Disassembly and Assembly, "Unit Injector Sleeve
- Remove".
b. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/5
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00570914
1. Remove hose assembly (1) from the front of the fuel manifold.
Illustration 2 g00570923
2. Remove hose assembly (2) from the rear of the fuel manifold.
2/5
992C WHEEL LOADER 42X00001-UP (MACHINE) POWERED BY 3412 ENGINE...
2021/6/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...