The document provides instructions for removing the rocker shaft and pushrods from the C4.2 engine. It outlines 13 steps to remove the rocker shaft assembly, pushrods, bridges and caps. Key steps include loosening nuts and disconnecting harnesses from the electronic unit injectors, loosening adjusting screws and bolts, and then removing the bolts to detach the rocker shaft assembly and pushrods. Proper cleaning and care is emphasized to prevent damage from contaminants.
Caterpillar cat 312 d excavator (prefix hjx) service repair manual (hjx00001 ...fksjksmmde
The document provides instructions for removing the rocker shaft and pushrods from a Caterpillar C4.2 engine used in a 312D excavator. It describes:
1) Loosening the harness assembly nuts and disconnecting the harnesses from the electronic unit injectors.
2) Loosening and removing bolts to detach the rocker shaft assembly and pushrods.
3) Disconnecting additional harness assemblies.
The goal is to properly remove the rocker shaft and pushrod components while keeping parts clean to prevent damage and premature wear.
1. The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine.
2. Key steps include disconnecting hoses and tubes, removing bolts, and lifting the cylinder head off using a lifting device as it weighs approximately 80 kg.
3. Reinstallation involves installing a new gasket, lowering the cylinder head into place, and tightening the bolts in a specified sequence.
1. The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine.
2. Key steps include disconnecting hoses and tubes, removing bolts, and lifting the cylinder head off using a lifting device as it weighs approximately 80 kg.
3. Reinstallation involves installing a new gasket, lowering the cylinder head into place, and tightening the bolts in a specified sequence.
1. The document provides instructions for removing the rocker shaft and pushrods from a C4.2 engine in a 312D excavator. It describes loosening bolts and nuts, removing harnesses, and taking off the rocker shaft assembly and pushrods.
2. Further instructions are given for disassembling the rocker shaft, including removing retaining rings, arms, brackets, springs, and bushings.
3. Reassembly of the rocker shaft is also outlined, listing the parts and tools needed and describing the process of installing springs, arms, bushings, and retaining rings back onto the shaft assembly.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fijsekkdmdm2w
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for removing and installing a cylinder head on a Caterpillar C6.4 engine.
2) To remove the cylinder head, hoses and tubes must first be disconnected and bolts loosened in a specified sequence before lifting the head off with a suitable lifting device.
3) Installation involves positioning a new gasket and cylinder head with a lifting device, and tightening bolts in a specified sequence to the correct torque.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...fusjekkdmdmd2w
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...f8uesjdkdmdm
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar cat 312 d excavator (prefix hjx) service repair manual (hjx00001 ...fksjksmmde
The document provides instructions for removing the rocker shaft and pushrods from a Caterpillar C4.2 engine used in a 312D excavator. It describes:
1) Loosening the harness assembly nuts and disconnecting the harnesses from the electronic unit injectors.
2) Loosening and removing bolts to detach the rocker shaft assembly and pushrods.
3) Disconnecting additional harness assemblies.
The goal is to properly remove the rocker shaft and pushrod components while keeping parts clean to prevent damage and premature wear.
1. The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine.
2. Key steps include disconnecting hoses and tubes, removing bolts, and lifting the cylinder head off using a lifting device as it weighs approximately 80 kg.
3. Reinstallation involves installing a new gasket, lowering the cylinder head into place, and tightening the bolts in a specified sequence.
1. The document provides instructions for removing and installing a cylinder head on a Caterpillar C4.2 engine.
2. Key steps include disconnecting hoses and tubes, removing bolts, and lifting the cylinder head off using a lifting device as it weighs approximately 80 kg.
3. Reinstallation involves installing a new gasket, lowering the cylinder head into place, and tightening the bolts in a specified sequence.
1. The document provides instructions for removing the rocker shaft and pushrods from a C4.2 engine in a 312D excavator. It describes loosening bolts and nuts, removing harnesses, and taking off the rocker shaft assembly and pushrods.
2. Further instructions are given for disassembling the rocker shaft, including removing retaining rings, arms, brackets, springs, and bushings.
3. Reassembly of the rocker shaft is also outlined, listing the parts and tools needed and describing the process of installing springs, arms, bushings, and retaining rings back onto the shaft assembly.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fijsekkdmdm2w
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for removing and installing a cylinder head on a Caterpillar C6.4 engine.
2) To remove the cylinder head, hoses and tubes must first be disconnected and bolts loosened in a specified sequence before lifting the head off with a suitable lifting device.
3) Installation involves positioning a new gasket and cylinder head with a lifting device, and tightening bolts in a specified sequence to the correct torque.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...fusjekkdmdmd2w
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...f8uesjdkdmdm
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fujkskemdmdm4r
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...ufjksemd8ujd
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like springs, arms, brackets and washers onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, pipes and bolts are fitted and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...km7seydwuhdw
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fskekkdmdmdm3e
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...jdkskmdmdm
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...prmy389342
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjskekdmmme
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove the lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to the lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjsekmsmmes
The document provides instructions for removing and installing a camshaft on a Caterpillar C6.4 engine. To remove the camshaft, first remove the valve lifters and then pull out the camshaft. To install the camshaft, lubricate the valve lifters, reinstall them in their original locations, and then insert the camshaft. Proper cleaning and lubrication of parts is important to prevent wear.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...tuzhiyou2
This document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the crankshaft pulley
- Removing the crankshaft front seal
- Installing a new crankshaft front seal
- Removing just the idler gear from the front gear group
The instructions include illustrations and specify the required tools for each procedure. Safety notices are also provided to keep parts clean and contain fluids properly during maintenance.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...jse7039222
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...lituo39419496
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...diskdkkdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 470 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repairs.
CASE IH PUMA 210 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual that contains information on the distribution systems for a tractor model. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, pneumatic system, electrical and electronic systems. It provides information on special tools needed for maintenance and repair of components within these various systems.
More Related Content
Similar to Caterpillar Cat 312D Excavator (Prefix HJX) Service Repair Manual (HJX00001 and up).pdf
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fujkskemdmdm4r
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...ufjksemd8ujd
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like springs, arms, brackets and washers onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, pipes and bolts are fitted and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...km7seydwuhdw
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual Instant D...fskekkdmdmdm3e
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...jdkskmdmdm
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...prmy389342
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to lifters and install them in the original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjskekdmmme
1. Remove the camshaft by first removing components like the cylinder head and lifters. Use a magnet to carefully remove the lifters and mark them for installation.
2. To install the camshaft, first apply lubricant to the lifters and install them in their original locations. Then position the camshaft and install any removed components like the cylinder head.
3. Proper cleaning and lubrication of parts is important to prevent damage and wear during assembly of the camshaft and other components.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjsekmsmmes
The document provides instructions for removing and installing a camshaft on a Caterpillar C6.4 engine. To remove the camshaft, first remove the valve lifters and then pull out the camshaft. To install the camshaft, lubricate the valve lifters, reinstall them in their original locations, and then insert the camshaft. Proper cleaning and lubrication of parts is important to prevent wear.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...tuzhiyou2
This document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the crankshaft pulley
- Removing the crankshaft front seal
- Installing a new crankshaft front seal
- Removing just the idler gear from the front gear group
The instructions include illustrations and specify the required tools for each procedure. Safety notices are also provided to keep parts clean and contain fluids properly during maintenance.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...jse7039222
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...lituo39419496
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...diskdkkdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Similar to Caterpillar Cat 312D Excavator (Prefix HJX) Service Repair Manual (HJX00001 and up).pdf (15)
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 470 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repairs.
CASE IH PUMA 210 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual that contains information on the distribution systems for a tractor model. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, pneumatic system, electrical and electronic systems. It provides information on special tools needed for maintenance and repair of components within these various systems.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding part orientations, identification marks and keys to ensure correct reassembly.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...f8usejkddmmd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, pulley, oil pan, gears, and pump.
2. Disconnecting a harness, cutting a cable strap, and removing bolts to detach a bypass tube.
3. Removing bolts of different lengths to separate the front housing from the engine. Care must be taken to properly contain fluids.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of hazards like released spring forces, hot or pressurized components, and ensuring fluids are contained. Required specialty tools are listed at the start for tasks like removing bearings, pistons, and other parts.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
CASE IH PUMA 195 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH PUMA tractors that contains sections covering the tractor's distribution systems, power systems (primary hydraulic, secondary hydraulic, pneumatic, electrical), electronic systems, power production systems (engine, fuel injection, air intake, exhaust, cooling, lubrication, starting), powertrain (transmission, reducers, PTOs), travelling systems (axles, steering, brakes, suspension, wheels), body and structure, user platform, environment control, and working arm/hitch. The introduction provides safety rules for working on the tractor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, and bearings. It then details 19 steps to disassemble the travel motor, removing seals, plates, pistons, and the barrel assembly. Safety cautions are provided throughout regarding contained fluids, pressurized components, and released spring forces.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 313D excavator. It lists the required tools and outlines 20 steps to disassemble the components. These include draining fluids, removing covers, plates, seals, springs, pistons, and other parts. Safety precautions are provided to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...f8usejkddmmd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety cautions are provided throughout regarding releasing pressures and spring forces.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746912
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection lines do not need to be removed in order to remove the rocker shaft and
pushrods.
1/2
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01375828
1. Loosen nuts (1) and disconnect harness assembly (2).
2. Repeat Step 13 for the remaining electronic unit injectors.
3. Disconnect harness assembly (3).
4. Remove bolts (4) and remove harness assembly (3).
Illustration 2 g01375847
5. Loosen nut (9). Loosen adjusting screw (11) by approximately one revolution.
6. Repeat Step 5 for the remaining rocker arms.
7. Loosen bolts (10). Do not remove bolts (10) at this time.
8. Loosen bolts (8). Do not remove bolts (8) at this time.
9. Remove bolts (10).
10. Remove bolts (8).
11. Remove rocker shaft assembly (5).
12. Remove pushrods (6).
13. Remove bridges (7) and the caps.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:20:42 UTC+0800 2020
2/2
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746773
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01375734
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolt (1) from shaft assembly (5).
2. Remove pipe (6) from shaft assembly (5).
3. Use Tooling (A) in order to remove retaining ring (2) from shaft assembly (5).
4. Remove washer (7) from shaft assembly (5).
5. Remove arm assembly (3) from shaft assembly (5).
6. Remove bracket (8) from shaft assembly (5).
7. Remove arm assembly (4) from shaft assembly (5).
8. Remove spring (9) from shaft assembly (5).
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g01375874
9. If necessary, use Tooling (B) in order to remove bushing (10) from arm assemblies (3) and
(4).
10. Repeat Steps 3 through 9 for the remaining rocker shaft assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:21:42 UTC+0800 2020
3/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746816
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01375874
1. If necessary, Use Tooling (B) in order to install bushing (10) into arm assemblies (4) and
(3).
Illustration 2 g01375734
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install spring (9) onto shaft assembly (5).
3. Install arm assembly (4) onto shaft assembly (5).
4. Install bracket (8) onto shaft assembly (5).
5. Install arm assembly (3) onto shaft assembly (5).
6. Install washer (7) onto shaft assembly (5).
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 7. Use Tooling (A) in order to install retaining ring (2) onto shaft assembly (5).
8. Repeat Steps 1 through 7 for the remaining rocker shaft assembly.
9. Install pipe (6) onto shaft assembly (5).
10. Install bolt (1). Tighten bolts (1) to a torque of 74 ± 5 N·m (55 ± 4 lb ft).
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:22:41 UTC+0800 2020
3/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746971
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01375847
1. Install bridges (7) and the caps.
2. Install pushrods (6).
3. Position rocker shaft assembly (5).
1/2
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 4. Position bolts (8). Do not tighten bolts (8) at this time.
5. Position bolts (10). Do not tighten bolts (10) at this time.
6. Tighten bolts (8) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
7. Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
8. Adjust adjusting screw (11) so that bridge (7) contacts both of the valve ends evenly.
Tighten nut (9) to a torque of 4 ± 1 N·m (35 ± 9 lb in).
9. Repeat Step 8 for the remaining rocker arms.
Illustration 2 g01375828
10. Position harness assembly (3) and install bolts (4).
11. Connect harness assembly (3).
12. Connect harness assembly (2) and tighten nuts (1).
13. Repeat Step 12 for the remaining electronic unit injectors.
14. Adjust the inlet valve lash to 0.250 mm (0.0098 inch). Adjust the exhaust valve lash to
0.400 mm (0.0157 inch). Refer to Testing and Adjusting, "Engine Valve Lash -
Test/Adjust".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:23:40 UTC+0800 2020
2/2
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02769384
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
B. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Remove".
C. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector -
Remove".
D. If necessary, remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold
- Remove and Install".
E. If necessary, remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove and Install".
F. If necessary, remove the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01375619
1. Disconnect hose (1) .
Illustration 2 g01375622
2. Disconnect tube assembly (2) .
3. Remove bolts (3). Disconnect tube assembly (4) and remove the gasket.
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01386192
Typical Example
Illustration 4 g01385983
4. Attach a suitable lifting device to cylinder head (5). The weight of cylinder head (5) is approximately
80 kg (177 lb).
5. Loosen cylinder head bolts (6) in the sequence that is shown in Illustration 4.
6. Use the suitable lifting device in order to remove cylinder head (5) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:24:40 UTC+0800 2020
3/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02772109
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01386192
Typical Example
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01386164
1. Install a new gasket. Attach a suitable lifting device to cylinder head (5). The weight of cylinder head
(5) is approximately 80 kg (177 lb). Use the suitable lifting device in order to position cylinder head
(5) on the engine block.
2. Tighten bolts (6) in the sequence that is shown in Illustration 2 to a torque of 137 ± 5 N·m (101 ± 4
lb ft).
Illustration 3 g01375622
3. Install a new gasket and connect tube assembly (4). Install bolts (3) .
4. Connect tube assembly (2) .
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01375619
5. Connect hose (1) .
End By:
a. If necessary, install the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator - Remove and Install".
b. If necessary, install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove and Install".
c. If necessary, install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
d. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector -
Install".
e. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Install".
f. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:25:39 UTC+0800 2020
3/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02751804
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00610824
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g00532061
1. Use a magnet in order to remove valve lifter (1) from the engine cylinder block, as shown.
Put identification marks on valve lifters (1) for installation purposes.
2. Repeat Step 1 for the remainder of valve lifters (1).
Illustration 3 g00613675
View (X) shows a good contact pattern. Views (Y) and (Z) show bad contact patterns.
Note: Check the valve lifters for wear.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00532061
1. Apply Tooling (A) to valve lifter (1) prior to installation. Install valve lifter (1) in the
original location in the engine cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:26:38 UTC+0800 2020
3/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02751903
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Remove".
b. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
c. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Note: In this removal procedure, the engine needs to be placed in the upside-down position. This
will allow the lifters to remain in position after the camshaft is removed.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00569371
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on fuel
injection drive gear (A) with the "33" mark on idler gear (B). Make an alignment of the "22" mark
on camshaft gear (C) with the "2" mark on idler gear (B). Align the "1" mark on crankshaft gear
(D) with the "11" mark on idler gear (B). The No. 1 cylinder is at the top center position when
these marks are in alignment.
1. Rotate the engine at 180 degrees in order to place the engine in the upside-down position.
This will ease the removal of the camshaft.
2/5
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00604521
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Remove
two bolts (1) and the washers that hold thrust plate (3) (not shown).
3. Carefully remove the camshaft, the thrust plate and the camshaft gear as an assembly.
4. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
Note: In this installation procedure, the engine needs to remain in the upside-down position in
order to keep the lifters in position while the camshaft is installed.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During installation, ensure that the camshaft is clean and lubricate all of the
components with clean engine oil.
1. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
3/5
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00569371
Note: During installation, ensure that the marks on the timing gears are in alignment. Align
the "3" mark on fuel injection drive gear (A) with the "33" mark on idler gear (B). Make an
alignment of the "22" mark on camshaft gear (C) with the "2" mark on idler gear (B). Align
the "1" mark on crankshaft gear (D) with the "11" mark on idler gear (B). The No. 1
cylinder is at the top center position when these marks are in alignment.
2. Apply Tooling (A) to the camshaft lobes. Carefully install the camshaft assembly into the
original location in the cylinder block.
Note: Caution must be used when the camshaft is installed in order to not damage the
camshaft lobe or the camshaft bearings.
Illustration 4 g00604521
3. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Install
bolts (1) and the washers that hold thrust plate (3). Tighten bolts (1) to a torque of
11 ± 2 N·m (97 ± 18 lb in).
End By:
4/5
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
b. Install the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Install".
c. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 22 15:27:37 UTC+0800 2020
5/5
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HJX
Configuration: 312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742801
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2321 Combination Puller 1
9S-9153 Puller Jaw 3
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g00598317
1. Use Tooling (A) in order to remove camshaft gear (1) from camshaft (3).
2. Remove thrust plate (2) from camshaft (3).
Note: Check the slot in the camshaft for the woodruff key for wear or damage.
Note: Check thrust plate (2) for wear or damage.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00598318
Note: During installation, ensure that camshaft (3) is clean and lubricate all of the
components with clean engine oil.
2/3
312D Excavator HJX00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP494...
2020/5/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...