This document provides instructions for disassembling and assembling the freewheel stator of a 980G Series II wheel loader power train. It describes 56 steps to disassemble the various components of the torque converter, including removing bearings, gears, seals, and housings. It emphasizes the importance of cleanliness during assembly and provides basic instructions to apply oil to bearings before reassembling components.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Caterpillar Cat 980G II WHEEL LOADER (Prefix AYT) Service Repair Manual Instant Download.pdf
1. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980G II WHEEL LOADER AYT
Configuration: 980G SERIES II WHEEL LOADER AYT00001-UP (MACHINE) POWERED BY 3406E
Disassembly and Assembly
980G Series II Wheel Loader Power Train
Media Number -RENR4378-05 Publication Date -01/01/2004 Date Updated -14/01/2004
i05903287
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B
8B-7548 Push-Puller 1
8B-7550 Leg 2
8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
C
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
D
5F-7343 Bearing Puller Attachment 1
1P-0520 Driver Group 1
E 1P-0510 Driver Group 1
F 7
1/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. Forcing Screw
3/8 - 16 x 3 in
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate" for the machine that is being serviced.
1. Place the torque converter housing assembly (2) on wood blocks.
Illustration 1 g00503225
2. Remove bolts (1) and the washers from torque converter housing assembly (2) .
Illustration 2 g01111329
3. Install Tooling (A) to torque converter housing assembly (2) , as shown. Attach a suitable
lifting device to Tooling (A) . The weight of housing assembly (2) is approximately 120 kg
(265 lb).
4. Use Tooling (F) to loosen housing assembly (2) from the torque converter.
2/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 5. Remove housing assembly (2) from the torque converter.
Illustration 3 g00871317
6. Remove O-ring seal (3) from torque converter housing assembly (2) .
Illustration 4 g00871318
7. Remove bolts (4) and the washers from pump adapter (5) and torque converter housing
assembly (2) .
3/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 5 g00871264
8. Use Tooling (F) to remove pump adapter (5) from torque converter housing assembly (2) .
Illustration 6 g00871319
9. Use tooling (C) to remove bearing cup (6) , O-ring seal (8) , and shims (7) from pump
adapter (5) . See illustration 13 for Tooling (C) .
Illustration 7 g00871326
4/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 10. Remove pump drive gear (9) from torque converter housing assembly (2) .
Illustration 8 g00871451
11. Use Tooling (B) to remove bearing cones (10) from each side to pump drive gear (9) .
Illustration 9 g00871333
12. Use Tooling (C) to remove bearing cup (11) from torque converter housing assembly (2) .
See illustration 13 for Tooling (C) .
5/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g01112900
13. Remove bolt (12) and the washer from torque converter housing assembly (2) .
14. Use Tooling (F) to push shaft assembly (14) out of torque converter housing assembly (2) .
15. Remove idler gear (13) from torque converter housing assembly (2) .
Illustration 11 g01112903
16. Remove O-ring seal (15) from shaft assembly (14) .
6/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 12 g00871365
17. Remove bearing cone (16) , bearing cone spacer (17) , and bearing cone (18) from idler gear
(13) .
Illustration 13 g00871366
18. Use Tooling (C) to remove bearing cup (19) from idler gear (13) .
Illustration 14 g00871367
19. Remove bearing cup spacer (20) from idler gear (13) .
7/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 15 g00871368
20. Remove retaining ring (21) from idler gear (13) .
Illustration 16 g00871369
21. Use Tooling (C) to remove bearing cups (22) from idler gear (13) .
8/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 17 g00871370
22. Remove studs (23) from torque converter housing assembly (2) .
Illustration 18 g00871267
23. Remove retaining ring (24) and bearing carrier (25) from the carrier assembly.
Illustration 19 g01112906
24. Remove bearing carrier (25) .
9/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 20 g00871269
25. Remove O-ring seal (26) from bearing carrier (25) .
26. Remove seal ring (27) from ring carrier (28) .
Illustration 21 g00871273
27. Use Tooling (D) and a press to remove ring carrier (28) from bearing carrier (25) .
10/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 22 g00871274
28. Remove retaining ring (29) from bearing carrier (25) .
Illustration 23 g00871275
29. Use Tooling (D) and a press to remove inner bearing (30) from bearing carrier (25) .
Illustration 24 g01112907
30. Remove bolts (31) and the washers from drive gear (32) .
31. Remove drive gear (32) .
11/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 25 g01112910
32. Use Tooling (E) and a press to remove the outer bearing race (32A) (not shown) from drive
gear (32) .
Illustration 26 g00871278
33. Remove retaining ring (33) from drive gear (32) .
Illustration 27 g00871279
12/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 34. Remove bolts (34) and the washers from drive flange (35) and rotating housing (36) .
Illustration 28 g00871281
35. Use bolts (34) as forcing screws to remove drive flange (35) from rotating housing (36) .
The weight of drive flange (35) is 23 kg (51 lb).
Illustration 29 g00871282
36. Remove bolts (37) from drive flange (35) .
13/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 30 g00871283
37. Remove drive flange (35) from impeller (38) .
Illustration 31 g00871284
38. Position impeller hub (39) on wood blocks.
39. Remove impeller (38) from impeller hub (39) .
Illustration 32 g00870210
14/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 40. Remove thrust bearing (40) and race (40A) (not shown) from carrier assembly (41) .
Illustration 33 g00870211
41. Remove carrier assembly (41) and stator (42) as a unit from rotating housing (36) .
Illustration 34 g00870212
42. Remove snap ring (43) from stator (42) . Remove plate (44) from stator (42) .
15/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 35 g01112913
43. Remove 11 freewheel rollers (45) and 11 freewheel springs (46) from freewheel cam (47) .
Remove stator (42) from carrier assembly (41) .
Illustration 36 g01112915
44. Remove retaining ring (48) . Remove plate (49) .
45. Use Tooling (E) and a hydraulic press in order to remove freewheel cam (47) from stator
(42) .
Note: If necessary, heat the stator to a maximum temperature of 135 °C (275 °F) for
approximately 15 minutes.
Illustration 37 g01112917
46. Remove thrust bearing (50) from carrier assembly (41) . Remove sleeve bearing (51) from
carrier assembly (41) .
16/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 38 g01112919
47. Remove thrust bearing race (52) and the thrust bearing.
Illustration 39 g00870286
48. Remove turbine (53) and turbine hub (54) as a unit from rotating housing (36) .
Illustration 40 g01112920
49. Remove bolts (55) and the washers that hold turbine (53) to hub (54) .
17/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 41 g00870755
50. Remove hub (54) from turbine (53) .
Illustration 42 g00870288
51. Remove retaining ring (56) from turbine hub (54) .
18/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 43 g01112924
52. Remove two races (57) and thrust bearing (58) .
Illustration 44 g00870291
53. Remove bolts (59) and the washers from cover assembly (60) .
54. Remove cover assembly (60) from rotating housing (36) .
55. Remove ring seal (61) from rotating housing (36) .
Illustration 45 g00870294
56. Remove sleeve bearing (62) from cover assembly (60) .
Copyright 1993 - 2022 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 19 10:18:51 UTC+0800 2022
19/19(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980G II WHEEL LOADER AYT
Configuration: 980G SERIES II WHEEL LOADER AYT00001-UP (MACHINE) POWERED BY 3406E
Disassembly and Assembly
980G Series II Wheel Loader Power Train
Media Number -RENR4378-05 Publication Date -01/01/2004 Date Updated -14/01/2004
i05903427
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
G
8T-5096 Dial Indicator Test Group 1
5P-2390 Gauge Tool Group 1
H 1P-0520 Driver Group 1
J -
Guide Pin
(3/8 - 16 by 8 in)
2
K -
Guide Pin
(1/2 - 13 by 3 in)
3
L 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, thoroughly cleaned in cleaning fluid.
Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement.
Note: Apply oil to all of the bearings before assembly.
1/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g01112937
1. Use Tooling (H) to install sleeve bearing (62) in cover assembly (60) . Sleeve bearing (62)
must be even with the outside surface of cover assembly (60) .
Illustration 2 g03337064
2. Install ring seal (61) to rotating housing (36) .
3. Install cover assembly (60) to rotating housing (36) .
4. Install bolts (59) and the washers to cover assembly (60) . Tighten the bolts to a torque of 30
± 5 N·m (22 ± 4 lb ft).
2/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 3 g00870744
5. Install races (57) and thrust bearing (58) to cover assembly (60) .
Illustration 4 g00870748
6. Install retaining ring (56) in turbine hub (54) .
Illustration 5 g00870755
7. Install turbine (53) on hub (54) .
3/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 6 g00870757
8. Install bolts (55) and the washers to turbine (53) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 7 g00870759
9. Install hub (54) and turbine (53) as a unit to rotating housing (36) .
4/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 8 g00870760
10. Install thrust bearing race (52) and the bearing to the turbine hub (54) .
Illustration 9 g01112941
11. Use Tooling (H) and a hydraulic press in order to install sleeve bearing (51) to carrier
assembly (41) . Install thrust bearing (50) to carrier assembly (41) .
Illustration 10 g01112915
5/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 11 g01112913
12. Use Tooling (H) and a hydraulic press in order to install freewheel cam (47) to stator (42) .
13. Install plate (49) to stator (42) . Install retaining ring (48) to stator (42) .
Note: If necessary, heat stator (42) to a maximum temperature of 135 °C (275 °F). Install
the cam with the IMPELLER SIDE facing downward. Continue with the installation until
freewheel cam (47) contacts the retaining ring (not shown).
14. Install stator (42) to carrier assembly (41) . Install freewheel springs (46) and freewheel
rollers (45) to freewheel cam (47) . Always install new freewheel springs (46) and
freewheel rollers (45) . Install freewheel springs (46) with the maximum number of loops in
freewheel springs (46) to the outside of freewheel cam (47) . Use the orientation of stator
(42) in Illustration 11 in reference to the following statement: Stator (42) should turn freely
in the clockwise direction. Stator (42) should not turn freely in the counterclockwise
direction.
Illustration 12 g00870421
15. Install plate (44) to stator (42) . Install snap ring (43) to stator (42) .
6/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 13 g00870422
16. Install carrier assembly (41) and stator (42) as a unit to rotating housing (36) .
Illustration 14 g00870762
17. Install thrust bearing (40) and race (40A) (not shown) to the carrier assembly (41) .
Illustration 15 g00870994
18. Position impeller hub (39) on a wood block.
7/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 19. Install impeller (38) on impeller hub (39) .
Illustration 16 g00870995
20. Install drive flange (35) on impeller (38) .
Illustration 17 g00871000
21. Install bolts (37) on drive flange (35) . Tighten the bolts to a torque of 80 ± 10 N·m (60 ± 7
lb ft).
8/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 18 g00871001
22. Install drive flange (35) on rotating housing (36) . The weight of drive flange (35) is
approximately 23 kg (51 lb).
23. Install bolts (34) and the washers to drive flange (35) . Tighten the bolts to a torque of 30 ±
5 N·m (22 ± 4 lb ft).
Illustration 19 g00871003
24. Install retaining ring (33) in the groove of drive gear (32) .
9/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 20 g00870829
25. Use the proper equipment to handle outer bearing race (32A) . Lower the temperature of
outer bearing race (32A) .
26. Install outer bearing race (32A) in drive gear (32) . Make sure that outer bearing race (32A)
contact retaining ring (33) .
Illustration 21 g00870763
27. Install drive gear (32) on drive flange (35) .
28. Install bolts (31) and the washers on drive gear (32) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 22 g00871006
29. Use the proper equipment to handle inner bearing (30) . Heat inner bearing (30) to a
maximum temperature of 135 °C (275 °F). Install inner bearing (30) on bearing carrier
(25) .
10/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. Illustration 23 g00871007
30. Install retaining ring (29) in the groove of bearing carrier (25) .
Illustration 24 g00871009
31. Use the proper equipment to handle ring carrier (28) . Heat ring carrier (28) to a maximum
temperature of 135 °C (275 °F). Install ring carrier (28) on bearing carrier (25) .
Illustration 25 g00871012
11/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. 32. Install seal ring (27) on ring carrier (28) .
33. Install O-ring seal (26) on bearing carrier (25) .
Illustration 26 g00871014
34. Install bearing carrier (25) in drive flange (35) .
Illustration 27 g00871015
35. Install retaining ring (24) and bearing carrier (25) on carrier assembly (28) .
12/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
32. Illustration 28 g00872709
36. Install studs (23) in torque converter housing assembly (2) . Tighten the studs to a torque of
100 ± 15 N·m (74 ± 11 lb ft).
Illustration 29 g00872711
37. Install retaining ring (21) in the groove of idler gear (13) .
Illustration 30 g00872713
13/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
33. 38. Use the proper equipment to handle bearing cup (22) . Lower the temperature of bearing cup
(22) . Install bearing cup (22) in idler gear (13) .
Illustration 31 g00872715
39. Flip idler gear (13) to the opposite side. Install bearing cup spacer (20) in idler gear (13) .
The notch in bearing cup spacer (20) must be aligned with retaining ring (21) .
Illustration 32 g00872716
40. Use the proper equipment to handle bearing cup (19) . Lower the temperature of bearing cup
(19) . Install bearing cup (19) in idler gear (13) .
14/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
34. Illustration 33 g00872718
41. Install bearing cone (16) , bearing cone spacer (17) , and bearing cone (18) in idler gear
(13) .
Illustration 34 g01112903
42. Apply clean hydraulic oil on O-ring seal (15) . Install O-ring seal (15) on shaft assembly
(14) .
Illustration 35 g01112954
15/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
35. 43. Install Tooling (K) in shaft assembly (14) .
44. Hold idler gear (13) in position in torque converter housing assembly (2) . Install shaft
assembly (15) .
45. Remove Tooling (K) from shaft assembly (14) .
Illustration 36 g01112970
46. Install bolt (12) that holds shaft assembly (14) in place in torque converter housing
assembly (2) . Tighten the bolt to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
Illustration 37 g00872724
47. Use the proper equipment to handle bearing cones (10) . Heat bearing cones to a maximum
temperature of 135 °C (275 °F). Install a bearing cone (10) on each side of pump drive gear
(9) .
16/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
36. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
37. Illustration 38 g00872801
48. Use the proper equipment to handle bearing cup (11) . Lower the temperature of bearing cup
(11) . Install bearing cup (11) in torque converter housing assembly (2) .
Illustration 39 g00872727
49. Install pump drive gear (9) in torque converter housing assembly (2) .
Illustration 40 g00872729
17/20(W)
w
2022/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...