This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 627H wheel tractor. It describes 18 steps to disassemble the torque converter, removing components like the retaining ring, impeller, stator, carrier assembly, and housing flange. It also lists one required tool, the driver group, to begin reassembling the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed to insert bearings and seals. Tools required include retaining ring pliers, drivers, pullers, and link brackets for lifting components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order and includes warnings to keep parts clean and use threadlocker during assembly.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to safely handle the parts.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed to insert bearings. Tools required include retaining ring pliers, drivers, pullers, and link brackets for lifting components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order, noting to keep parts clean and apply Loctite to the threaded rod.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed to insert bearings and seals. Tools required include retaining ring pliers, drivers, pullers, and link brackets for lifting components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order and includes warnings to keep parts clean and use threadlocker during assembly.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to safely handle the parts.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed to insert bearings. Tools required include retaining ring pliers, drivers, pullers, and link brackets for lifting components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order, noting to keep parts clean and apply Loctite to the threaded rod.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal components like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling individual components of the torque converter housing, impeller, carrier assembly, stator, turbine, and hub. Precise alignment marks are made and specific torque specifications and press tools are required.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, thrust races, and pressing or pulling components apart. Precise alignment marks are made for reassembly.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, seals, races, springs, and other components from the housing, impeller, carrier assembly, stator, turbine, and hub. Detailed illustrations accompany each step.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, thrust races, and pressing or pulling components apart. Precise alignment marks are made for reassembly.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for a 621H wheel tractor transmission planetary system. It outlines 37 steps to fully disassemble the transmission, including removing the transmission from the housing, separating the clutch housings, carrier assembly and gears, and removing all internal components like springs, plates, pins and seals. Detailed illustrations accompany each step and safety warnings are provided regarding released spring forces. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
More Related Content
Similar to Caterpillar Cat 627H WHEEL TRACTOR (Prefix DBW) Service Repair Manual Instant Download.pdf
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal components like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling individual components of the torque converter housing, impeller, carrier assembly, stator, turbine, and hub. Precise alignment marks are made and specific torque specifications and press tools are required.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, thrust races, and pressing or pulling components apart. Precise alignment marks are made for reassembly.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, seals, races, springs, and other components from the housing, impeller, carrier assembly, stator, turbine, and hub. Detailed illustrations accompany each step.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, thrust races, and pressing or pulling components apart. Precise alignment marks are made for reassembly.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
This document provides disassembly instructions for a 621H wheel tractor transmission planetary system. It outlines 37 steps to fully disassemble the transmission, including removing the transmission from the housing, separating the clutch housings, carrier assembly and gears, and removing all internal components like springs, plates, pins and seals. Detailed illustrations accompany each step and safety warnings are provided regarding released spring forces. Required tools are listed.
This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
Similar to Caterpillar Cat 627H WHEEL TRACTOR (Prefix DBW) Service Repair Manual Instant Download.pdf (17)
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
This document provides instructions for removing and installing the camshaft on a Caterpillar 3412C engine. Key steps include:
1. Removing the front housing, lifter group, and flywheel housing.
2. Removing four bolts and a plate from the rear of the camshaft and removing the camshaft gear.
3. Aligning timing marks and removing two bolts and a plate from the camshaft.
4. Removing the camshaft from the cylinder block and optionally removing the camshaft gear using a driver group tool.
This service repair manual provides instructions for removing and installing the flywheel housing and rear power take-off (RPTO) on a Caterpillar 657G wheel tractor. The flywheel housing removal procedure involves removing bolts and seals, then lifting the housing off using lifting brackets. Installation involves cleaning parts, applying sealant, positioning seals and gaskets, and tightening bolts in a specific sequence. The RPTO removal procedure describes removing gears, idlers, retainers, sleeves and covers. Installation involves cleaning, lubricating, and positioning these parts before securing with bolts.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing O-rings, bolts, bearings, and shaft components.
This document provides instructions for installing a crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes cleaning and applying retaining compound to the crankshaft and wear sleeve. A locator is installed on the crankshaft to position the wear sleeve and seal, which are then installed using an installer tool. Finally, the installer is removed and bolts are tightened to complete the installation.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including gears, shafts, bearings, and seals. The assembly process describes installing these components in 23 steps, noting proper orientation and torque specifications. Tools required include various pullers, presses, and forcing screws.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hydraulic and electrical connections, draining fluid from the elbow, attaching a lifting device to the pump, and removing mounting nuts and the pump. Cleaning parts and plugging lines is noted for prevent contamination during removal.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Removing the flywheel by using bolting brackets to hold the crankshaft gear, installing guide bolts, and lifting the flywheel off with a hoist.
- Reinstalling components by pressing bearings into place with drives, torquing bolts, and checking runout after installing the flywheel.
The document provides detailed step-by-step instructions accompanied by illustrations of the disassembly and
This document provides instructions for installing and removing the crankshaft rear seal on a Caterpillar 657E wheel scraper. The removal procedure involves using a punch or slide hammer puller to puncture and remove the existing seal. The installation procedure specifies using a seal installer tool and retaining compound to press the new seal and wear sleeve onto the crankshaft. Precautions are given to keep the components clean and not reuse a separated seal and sleeve. The instructions are illustrated with diagrams and apply to both engine configurations with and without a rear gear train.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 651E wheel scraper. The removal procedure involves using various tools to disassemble the adapter assemblies, gears, bearings and other components. The installation procedure describes cleaning and lubricating parts, pressing or installing bearings and gears back into place, and reassembling the components in reverse order. Precautions are given to keep parts clean and lubricated to prevent wear.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including the housing assembly, torque converter assembly, impeller wheel assembly, carrier assembly, and stator assembly. It then describes assembling the torque converter in 25 steps by installing the parts in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and slide hammers.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...9fikslkddmd8u
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...9fikslkddmd8u
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing components like the camshaft gear and rocker arms first. Tools like a cradle, guide, camshaft pilots and hooks are then used to support the camshaft as it is moved out of the cylinder head and into the guide. Care must be taken to avoid damaging the camshaft or bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides disassembly instructions for the transmission of a 637G Wheel Tractor. It lists the required tools and outlines 39 steps to fully disassemble the transmission planetary and its components. These include removing clutch housings, carrier assemblies, shafts, gears, seals, springs, and other internal parts. Care must be taken when handling components under spring force or with significant weight.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 627H WHEEL TRACTOR DBW
Configuration: 627H Wheel Tractor Scraper DBW00001-UP (MACHINE)
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04496349
Torque Converter - Disassemble - Tractor
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C 6L-7283 Bolts 2
Start By:
a. Remove the torque converter.
Illustration 1 g01052899
1/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. 1. Use Tooling (A) in order to remove retaining ring (1) from carriage support assembly (2).
Remove carriage support assembly (2) from hub (3). Use Tooling (B) and a suitable press in
order to remove the sleeve bearing from carriage support assembly (2).
Illustration 2 g00525303
2. Remove bolts (4) and the washers from torque converter impeller (5). Remove bolts (6), the
washers, and clamp plate (7) from impeller hub (8).
Illustration 3 g00525304
3. Install Tooling (C) in torque converter impeller (5). Use Tooling in order to remove torque
converter impeller (5) and impeller hub (8) from housing (9).
2/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 4 g00525305
4. Remove metal seal ring (10) from torque converter impeller (5). Remove impeller hub (8)
from torque converter impeller (5).
Illustration 5 g00525306
5. Remove thrust bearing (11) from carrier assembly (12).
Illustration 6 g00525308
Illustration 7 g00525309
6. Remove carrier assembly (12) and torque converter stator (13) as a unit from housing (9).
3/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. 7. Position carrier assembly (12) and torque converter stator (13), as shown. Use Tooling (A)
in order to remove retaining ring (14) from torque converter stator (13). Remove thrust race
(15) from torque converter stator (13).
Illustration 8 g00525863
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove freewheel rollers (16) and freewheel springs (17) from freewheel cam (18).
Remove torque converter stator (13) from carrier assembly (12).
Illustration 9 g01080684
9. Use Tooling (A) in order to remove retaining ring (19) from torque converter stator (13).
Remove side plate (20) from torque converter stator (13).
4/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. 10. Use Tooling (B) and a suitable press in order to remove freewheel cam (18) (not shown)
from torque converter stator (13).
Illustration 10 g01052916
11. Remove thrust bearing (21) from carrier assembly (12). Remove sleeve bearing (22) from
carrier assembly (12).
Illustration 11 g00525315
12. Remove torque converter turbine (23) and hub (3) as a unit from housing (9).
Illustration 12 g01052922
5/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. 13. Remove thrust bearing (24) and thrust race (25) from hub (3).
Illustration 13 g00525320
14. Position torque converter turbine (23), as shown. Remove thrust race (26) from hub (3). Put
an alignment mark on torque converter turbine (23) and hub (3) for installation purposes.
Remove bolts (27) from torque converter turbine (23).
Illustration 14 g00525321
15. Remove clamp ring (28) and torque converter turbine (23) from hub (3).
Illustration 15 g00525322
6/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. 16. Remove thrust bearing (29) and thrust race (30) from housing (9).
Illustration 16 g00528612
17. Remove bolts (31) and flange (32) from housing (9).
Illustration 17 g00525323
18. Remove sleeve bearing (33) from flange (32).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 21:47:10 UTC+0800 2021
7/7(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 627H WHEEL TRACTOR DBW
Configuration: 627H Wheel Tractor Scraper DBW00001-UP (MACHINE)
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04351575
Torque Converter - Disassemble - Scraper
SMCS - 3101-015
S/N - DBW1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 1P-2420 Transmission Repair Stand 1
C 1P-0520 Driver Gp 1
D 8H-0663 Bearing Puller Gp 1
E
1P-2322 Combination Puller 1
1P-0546 Puller Jaw 1
1P-0510 Driver Gp 1
F 1P-0074 Slide Hammer Puller Gp 1
Start By:
a. Separate Torque Converter, Transmission, and Transfer Gear.
1/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 1 g02477139
Illustration 2 g02477145
1. Attach Tooling (A) and a suitable lifting device to housing assembly (2) . Reposition
housing assembly (2) onto Tooling (B). The weight of housing assembly (2) is
approximately 73 kg (160 lb).
2. Remove bolts (1) and lift housing assembly (2) from torque converter assembly (3).
Illustration 3 g02477249
3. Reposition torque converter assembly (3) on Tooling (B) as shown. The weight of torque
converter assembly (3) is approximately 34 kg (76 lb).
2/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. 4. Remove bolts (4).
Illustration 4 g02477847
5. Attach Tooling (A) and a suitable lifting device to cover assembly (5). Remove cover
assembly (5) from torque converter assembly (3).
Illustration 5 g02494878
6. Remove clutch piston (6).
Illustration 6 g02495236
3/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. 7. Remove friction disk (7). Remove bolts (10) and shaft retainer (8). Remove hub (9) and seal
rings.
Illustration 7 g02487237
Illustration 8 g02491136
8. Remove bolts (12). Remove bearing retainer (11). Remove retaining ring (13). Remove
upper bearing race (16). Remove retaining ring (14). Remove bearing (15).
Illustration 9 g02487278
9. Reposition torque converter assembly (3) on Tooling (B) as shown. The weight of torque
converter assembly (3) is approximately 34 kg (76 lb).
4/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. 10. Remove bolts (17).
Illustration 10 g02494482
11. Attach Tooling (A) to impeller wheel assembly (18). Remove impeller wheel assembly (18).
The weight of impeller wheel assembly (18) is approximately 34 kg (76 lb).
Illustration 11 g02484296
12. Remove retaining ring (19) from bearing (20).
Illustration 12 g02488758
5/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. 13. Use Tooling (E) to separate shaft assembly (21) from bearing assembly (20) and carrier
assembly (22).
Illustration 13 g02492076
Illustration 14 g02488997
14. Remove bolts (23). Use Tooling (F) to remove stator assembly (24) from carrier assembly
(22) and impeller wheel assembly (18).
Illustration 15 g02489038
6/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 16 g02489042
15. Remove bolts (25). Use Tooling (C) to remove carrier assembly (22) from impeller wheel
assembly (18).
Illustration 17 g02489047
16. Using Tooling (C) and a suitable press to remove bearing (26) and gear (27) from carrier
assembly (22).
Illustration 18 g02489056
17. Remove seal ring (28).
7/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 19 g02492176
18. Remove seal rings (29). Remove retaining ring (30) from shaft assembly (21).
Illustration 20 g02489277
Illustration 21 g02489280
19. Install Tooling (D).
Note: Tooling (D) must be seated on the shoulder of turbine (31) in order to support turbine
and prevent damage. Tooling (D) must not contact the splines on shaft (21).
8/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 20. Use a suitable press to remove shaft assembly (21) from turbine (31). Remove bearing race
(32) and the spacer from turbine (31).
Illustration 22 g02492441
21. Position housing assembly (2) as shown.
22. Remove bolts (33) and gear (34).
Illustration 23 g02492458
23. Remove retaining rings (35) from gear (34).
Illustration 24 g02492476
9/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. 24. Use a suitable press and Tooling (C) in order to remove bearing (36) and shaft from gear
(34).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 21:48:07 UTC+0800 2021
10/10(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 627H WHEEL TRACTOR DBW
Configuration: 627H Wheel Tractor Scraper DBW00001-UP (MACHINE)
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i07459845
Torque Converter - Assemble - Tractor
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
D 8T-5096 Dial Indicator Group 1
Illustration 1 g00528674
1. Use Tooling (B) and a suitable press to install sleeve bearing (33). Install sleeve bearing
(33) to flange (32).
1/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 2 g00528612
2. Install bolts (31) and flange (32) to housing (9). Tighten bolts (31) to a torque of
120 ± 15 N.m (89 ± 11 lb ft).
Illustration 3 g00525322
3. Install thrust race (30) and thrust bearing (29) to housing (9).
Illustration 4 g00525321
4. Install torque converter turbine (23) and clamp ring (28) to hub (3).
2/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 5 g06329533
5. Install bolts (27) to torque converter turbine (23). Tighten bolts (27) to a torque of
50 ± 7 N.m (37 ± 5 lb ft).
Illustration 6 g01052922
6. Install thrust race (25) and thrust bearing (24) to hub (3).
Illustration 7 g06329534
7. Install thrust race (26) to hub (3).
3/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 8 g00525315
8. Install torque converter turbine (23) and hub (3) as a unit to housing (9).
Illustration 9 g00528953
9. Use Tooling (B) and a suitable press to install sleeve bearing (22). Install sleeve bearing
(22) to carrier assembly (12).
10. Install thrust bearing (21) to carrier assembly (12).
Illustration 10 g01052912
4/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. 11. Install side plate (20) to torque converter stator (13). Use Tooling (A) to install retaining
ring (19). Install retaining ring (19) to torque converter stator (13).
Illustration 11 g00525863
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Use Tooling (B) and a suitable press to install freewheel cam (18). Install freewheel cam
(18) to torque converter stator (13).
13. Install torque converter stator (13) to carrier assembly (12). Install freewheel springs (17)
and freewheel rollers (16) to freewheel cam (18). Always install new freewheel springs (17)
and freewheel rollers (16). Install freewheel springs (17) with the maximum number of
loops in freewheel springs (17) to the outside of freewheel cam (18). Torque converter
stator (13) should turn freely in the counterclockwise direction. Torque converter stator (13)
should not turn freely in the clockwise direction.
5/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Illustration 12 g00525309
14. Install thrust race (15) to torque converter stator (13). Use Tooling (A) to install retaining
ring (14). Install retaining ring (14) to torque converter stator (13).
Illustration 13 g00525308
15. Install carrier assembly (12) and torque converter stator (13) as a unit to housing (9).
Illustration 14 g00525306
16. Install thrust bearing (11) to carrier assembly (12).
6/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Illustration 15 g00525305
17. Install impeller hub (8) to torque converter impeller (5). Install metal seal ring (10) to torque
converter impeller (5).
Illustration 16 g00525303
18. Install clamp plate (7), the washers, and bolts (6) to impeller hub (8). Tighten bolts (6) to a
torque of 50 ± 7 N.m (37 ± 5 lb ft).
19. Install bolts (4) and the washers to torque converter impeller (5). Tighten bolts (4) to a
torque of 50 ± 7 N.m (37 ± 5 lb ft).
Illustration 17 g00525299
20. Use Tooling (B) and a suitable press to install the sleeve bearing in carriage support
assembly (2). Install the sleeve bearing until the sleeve bearing is flush with the outside
machined surface of carriage support assembly (2).
21. Install carriage support assembly (2) to hub (3). Use Tooling (A) to install retaining ring (1).
Install retaining ring (1) to carriage support assembly (2).
7/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 18 g01053220
22. Install Tooling (D) to the torque converter, as shown. The edge of Tooling (D) must be in
contact with the edge of carrier assembly (12), as shown. Move hub (3) up and down with a
screwdriver. The end play of hub (3) must be 0.13 to 1.96 mm (0.005 to 0.077 inch).
End By:
a. Install the torque converter.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 21:49:04 UTC+0800 2021
8/8(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 627H WHEEL TRACTOR DBW
Configuration: 627H Wheel Tractor Scraper DBW00001-UP (MACHINE)
Disassembly and Assembly
621H, 623H and 627H Wheel Tractor-Scrapers Power Train
Media Number -KENR8883-02 Publication Date -01/06/2013 Date Updated -01/07/2013
i04578058
Torque Converter - Assemble - Scraper
SMCS - 3101-016
S/N - DBW1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 1P-2420 Transmission Repair Stand 1
C 1P-0520 Driver Gp 1
G -
Threaded Rod
3/8-16 by 4.00
1
H - Locktite 242 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Illustration 1 g02492476
1. Use a suitable press and Tooling (C) to install bearing (36) and shaft into gear (34).
Illustration 2 g02492458
2. Install retaining ring (35) on each side of gear (34) .
Illustration 3 g02492441
3. Position housing assembly (2) as shown.
2/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
29. 4. Install gear (34). Install bolts (33) .
Illustration 4 g02492617
5. Lower the temperature of shaft assembly (21). Install retaining ring (30). Install shaft
assembly (21) in the turbine (31) until ring (30) rests on the turbine (31). Install seal rings
(29) .
Illustration 5 g02492679
6. Install the spacer. Raise the temperature of bearing race (32). Install bearing race (32) on
shaft assembly (21) .
3/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
30. Illustration 6 g02489056
7. Install seal ring (28) .
Illustration 7 g02482957
8. Install gear (27) to carrier assembly (22) .
Illustration 8 g02482978
9. Raise the temperature of bearing (26). Install bearing (26) on carrier assembly (22) .
4/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
31. Illustration 9 g02483898
Illustration 10 g02483903
10. Position lower part of carrier assembly (22) under impeller wheel assembly (18) .
11. Install Tooling (G) to align carrier assembly (22) with impeller wheel assembly (18) .
Illustration 11 g02483983
5/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
32. 12. Install bolts (25). Tighten bolts (25) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 12 g02492076
13. Position stator assembly (24) on carrier assembly (22). Apply Tooling (H) to bolts (23).
Install bolts (23). Tighten bolts (23) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
Illustration 13 g02484278
14. Install carrier assembly (22) and impeller wheel assembly (18) on turbine (31) and shaft
assembly (21) .
6/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
33. Illustration 14 g02484377
Note: Install bearing (20) with Radius Side (X) facing down, toward carrier assembly (22).
Illustration 15 g02484296
15. Raise the temperature of bearing (20). Install bearing. Install retaining ring (19) .
Illustration 16 g02487297
7/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
34. 16. Attach Tooling (A) and a suitable lifting device to impeller wheel assembly (18). The
weight of impeller wheel assembly (18) is approximately 34 kg (76 lb). Install impeller
wheel assembly (18) into torque converter assembly (3) .
Illustration 17 g02487278
17. Install bolts (17). Tighten bolts (17) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
18. Reposition torque converter assembly (3) on Tooling (B). The weight of torque converter
assembly (3) is approximately 64 kg (142 lb).
Illustration 18 g02491136
19. Lower the temperature of bearing (15) and install bearing. Install retaining ring (14). Install
upper bearing race (16) and retaining ring (13) .
8/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
35. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
36. Illustration 19 g02487237
20. Install bearing retainer (11). Install bolts (12). Tighten bolts (12) to a torque of 50 ± 7 N·m
(37 ± 5 ft).
Illustration 20 g02495236
21. Install hub (9). Install shaft retainer (8) and the seal rings. Install bolts (10). Tighten bolts
(10) to a torque of 50 ± 7 N·m (37 ± 5 lb ft). Install friction disk (7) .
Illustration 21 g02494878
9/12(W)
w
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...