This document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and electrical connections, and removing mounting bolts. For installation, the process is reversed - mounting bolts are reinstalled, hoses and electrical connections are reconnected, and then the tank is refilled. Additional sections provide instructions for disassembling the pump drive unit by removing mounting bolts, seals, and bearings.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fjskekmsemmwe
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and harnesses, and removing mounting bolts. The tank is then lifted out. For installation, the process is reversed - the tank is positioned and bolted in, then hoses and harnesses are reconnected before refilling the tank. Additional sections provide instructions for removing the pump drive unit and disassembling the pump drive housing.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fjkskekdmmenm
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined, and illustrations show each step.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...ujdjfjjskekmm
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...ujjdjjkksmmd
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fujsefkskekmm
This document provides instructions for removing the pump drive on a Caterpillar 973C track loader. It describes disconnecting hoses, tubes, brackets and removing bolts to detach the implement pump, filter group, hydrostatic valve and other components. Ten detailed steps are outlined including draining fluids, marking connections, lifting components and making sure to contain contaminants during the process. The goal is to properly remove the entire pump drive assembly for maintenance or repair.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fjskekmsemmwe
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and harnesses, and removing mounting bolts. The tank is then lifted out. For installation, the process is reversed - the tank is positioned and bolted in, then hoses and harnesses are reconnected before refilling the tank. Additional sections provide instructions for removing the pump drive unit and disassembling the pump drive housing.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fjkskekdmmenm
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined, and illustrations show each step.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...ujdjfjjskekmm
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...ujjdjjkksmmd
The document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and wiring, and removing mounting bolts to detach the tank from the machine. Reinstallation involves following the removal steps in reverse order and refilling the tank. Safety precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 973 c track loader (prefix bcp) service repair manual (bcp000...fujsefkskekmm
This document provides instructions for removing the pump drive on a Caterpillar 973C track loader. It describes disconnecting hoses, tubes, brackets and removing bolts to detach the implement pump, filter group, hydrostatic valve and other components. Ten detailed steps are outlined including draining fluids, marking connections, lifting components and making sure to contain contaminants during the process. The goal is to properly remove the entire pump drive assembly for maintenance or repair.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine. The removal process involves:
1. Draining the cooling system and removing various other components to access the cylinder head
2. Detaching hoses and sensors and removing mounting bolts
3. Lifting the cylinder head off using a strap
4. Removing gaskets and seals
The installation is the reverse of removal, and includes cleaning, lubricating, and torquing components to the specified settings. Proper timing of installation is critical to avoid engine damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of approximately 235 kg.
2. To install the cylinder head, begin by installing seals and gaskets, then lift the head into place and install bolts in a tightening sequence before reconnecting components.
3. The document also describes removing the camshaft by installing support tools, removing covers, and sliding out the camshaft while supported to avoid damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing support tools to safely hold the camshaft as it is slid out of the engine
4. Using hooks and pilots to carefully slide the camshaft forward and remove it, being careful not to damage surfaces.
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine. The removal process involves:
1. Draining the cooling system and removing various other components to access the cylinder head
2. Detaching hoses and sensors and removing mounting bolts
3. Lifting the cylinder head off using a strap
4. Removing gaskets and seals
The installation is the reverse of removal, and includes cleaning, lubricating, and torquing components to the specified settings. Proper timing of installation is critical to avoid engine damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...udfjjsekkemm
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms.
2. Removing bolts and plates at the front of the engine.
3. Installing support tools in the engine to support the camshaft.
4. Sliding the camshaft forward and out of the engine using support tools to avoid damaging the camshaft or bearings.
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...ujsefksmemtyu
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting off the cylinder head using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates in reverse order of removal
2. Lifting and positioning the cylinder head
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reconnecting components and ref
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fujskksemmk
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting the cylinder head off using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates
2. Lifting the cylinder head into place
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reattaching components and refilling the cooling system
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fksuekdjsekmmd
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting the cylinder head off using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates
2. Lifting the cylinder head into place
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reattaching components and refilling the cooling system
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fuujsjejkekmd
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms.
2. Removing bolts and plates at the front of the engine.
3. Installing support tools in the engine to support the camshaft.
4. Sliding the camshaft forward and out of the engine using support tools to avoid damaging the camshaft or bearings.
This service repair manual provides instructions for repairing 330D and 330D L excavators. It details the process for removing and installing the cylinder head, which includes draining coolant, removing mounting bolts and hoses, and lifting the head off using a lifting bracket. It also provides instructions for removing and installing the camshaft, which involves aligning timing marks, removing mounting bolts, and sliding the camshaft in and out of the engine block. Precautions are given to keep parts clean and avoid damaging lobes or bearings during removal and installation.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...shudun96087
This document provides instructions for removing and installing the camshaft on a Caterpillar C9 engine. The removal procedure involves using a hook tool to lift each camshaft lobe out of the cylinder head after removing the rocker arm and shaft assembly. The installation procedure specifies applying lubricant to the camshaft lobes before positioning them back into the cylinder head using the hook tool. Proper lubrication and placement of parts is emphasized to prevent premature wear and failure.
Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H2005...han647runken
This document is a shop manual for the WA470-3 Wheel Loader that provides instructions on general safety, structure and function, testing and adjusting, disassembly and assembly, and maintenance standards. It outlines 23 general safety precautions to follow when working on the machine, such as wearing protective equipment, using lifting equipment properly, and following tightening torques. The manual is divided into sections for different components and contains technical information, troubleshooting charts, and step-by-step instructions for repairs. Symbols are used to mark important safety information and technical details.
Komatsu WA150PZ-5 Wheel Loader Service Repair Manual (SN H50051 and up).pdfhan647runken
This document provides specifications and information about a WA150PZ-5 wheel loader, including:
- General assembly drawings and dimensions of the machine.
- Engine specifications including model, horsepower, torque, and fuel consumption.
- Performance specifications such as operating weight, bucket capacity, travel speeds, and gradeability.
- Hydraulic system details including pump models and cylinder sizes.
- A weight table listing weights of individual machine components.
- A list of recommended lubricants and coolants for the engine, transmission, hydraulics, axles, and other systems.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...han647runken
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...han647runken
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major systems and components with reference page numbers. An example parts list is then provided for the engine mounting system with part numbers, descriptions, and other specifications.
More Related Content
Similar to Caterpillar Cat 973C TRACK LOADER (Prefix BCP) Service Repair Manual (BCP00001 and up).pdf
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine. The removal process involves:
1. Draining the cooling system and removing various other components to access the cylinder head
2. Detaching hoses and sensors and removing mounting bolts
3. Lifting the cylinder head off using a strap
4. Removing gaskets and seals
The installation is the reverse of removal, and includes cleaning, lubricating, and torquing components to the specified settings. Proper timing of installation is critical to avoid engine damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of approximately 235 kg.
2. To install the cylinder head, begin by installing seals and gaskets, then lift the head into place and install bolts in a tightening sequence before reconnecting components.
3. The document also describes removing the camshaft by installing support tools, removing covers, and sliding out the camshaft while supported to avoid damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing support tools to safely hold the camshaft as it is slid out of the engine
4. Using hooks and pilots to carefully slide the camshaft forward and remove it, being careful not to damage surfaces.
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine. The removal process involves:
1. Draining the cooling system and removing various other components to access the cylinder head
2. Detaching hoses and sensors and removing mounting bolts
3. Lifting the cylinder head off using a strap
4. Removing gaskets and seals
The installation is the reverse of removal, and includes cleaning, lubricating, and torquing components to the specified settings. Proper timing of installation is critical to avoid engine damage.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C15 engine:
1. To remove the cylinder head, disconnect hoses and sensors, remove bolts, and lift off the head using a lifting device due to its heavy weight of around 518 pounds.
2. To install the cylinder head, begin by installing gaskets and seals, then place the head on dowel pins and bolt it down evenly in a sequence using specific torque values. Reconnect all hoses and sensors.
3. The document also describes removing the camshaft by using support tools to maneuver it out of position while avoiding damage to surfaces. Proper alignment and installation of support tools is required for
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...udfjjsekkemm
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms.
2. Removing bolts and plates at the front of the engine.
3. Installing support tools in the engine to support the camshaft.
4. Sliding the camshaft forward and out of the engine using support tools to avoid damaging the camshaft or bearings.
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...ujsefksmemtyu
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting off the cylinder head using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates in reverse order of removal
2. Lifting and positioning the cylinder head
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reconnecting components and ref
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fujskksemmk
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting the cylinder head off using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates
2. Lifting the cylinder head into place
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reattaching components and refilling the cooling system
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fksuekdjsekmmd
This document provides instructions for removing and installing the cylinder head on a Caterpillar C15 engine.
The removal procedure involves:
1. Removing components like the camshaft gear and injectors
2. Draining the cooling system
3. Removing bolts and plates holding the cylinder head in place
4. Lifting the cylinder head off using a lifting device
5. Removing gaskets and seals
The installation procedure outlines:
1. Installing gaskets, seals and plates
2. Lifting the cylinder head into place
3. Reinstalling bolts and tightening them in a specific sequence and torque
4. Reattaching components and refilling the cooling system
Caterpillar cat 740 b articulated truck (prefix l4e) service repair manual (l...fuujsjejkekmd
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms.
2. Removing bolts and plates at the front of the engine.
3. Installing support tools in the engine to support the camshaft.
4. Sliding the camshaft forward and out of the engine using support tools to avoid damaging the camshaft or bearings.
This service repair manual provides instructions for repairing 330D and 330D L excavators. It details the process for removing and installing the cylinder head, which includes draining coolant, removing mounting bolts and hoses, and lifting the head off using a lifting bracket. It also provides instructions for removing and installing the camshaft, which involves aligning timing marks, removing mounting bolts, and sliding the camshaft in and out of the engine block. Precautions are given to keep parts clean and avoid damaging lobes or bearings during removal and installation.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...shudun96087
This document provides instructions for removing and installing the camshaft on a Caterpillar C9 engine. The removal procedure involves using a hook tool to lift each camshaft lobe out of the cylinder head after removing the rocker arm and shaft assembly. The installation procedure specifies applying lubricant to the camshaft lobes before positioning them back into the cylinder head using the hook tool. Proper lubrication and placement of parts is emphasized to prevent premature wear and failure.
Similar to Caterpillar Cat 973C TRACK LOADER (Prefix BCP) Service Repair Manual (BCP00001 and up).pdf (15)
Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H2005...han647runken
This document is a shop manual for the WA470-3 Wheel Loader that provides instructions on general safety, structure and function, testing and adjusting, disassembly and assembly, and maintenance standards. It outlines 23 general safety precautions to follow when working on the machine, such as wearing protective equipment, using lifting equipment properly, and following tightening torques. The manual is divided into sections for different components and contains technical information, troubleshooting charts, and step-by-step instructions for repairs. Symbols are used to mark important safety information and technical details.
Komatsu WA150PZ-5 Wheel Loader Service Repair Manual (SN H50051 and up).pdfhan647runken
This document provides specifications and information about a WA150PZ-5 wheel loader, including:
- General assembly drawings and dimensions of the machine.
- Engine specifications including model, horsepower, torque, and fuel consumption.
- Performance specifications such as operating weight, bucket capacity, travel speeds, and gradeability.
- Hydraulic system details including pump models and cylinder sizes.
- A weight table listing weights of individual machine components.
- A list of recommended lubricants and coolants for the engine, transmission, hydraulics, axles, and other systems.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...han647runken
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...han647runken
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major systems and components with reference page numbers. An example parts list is then provided for the engine mounting system with part numbers, descriptions, and other specifications.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...han647runken
This document provides parts information for the engine and related systems of an HM350-1L machine with serial number A10001 or higher. It includes sections for the engine mounting, hoses, air intake and exhaust piping, air cleaner components, and other engine parts. Lists of part numbers, descriptions, and quantities are provided for each item.
Komatsu HM350-1 Articulated Dump Truck Parts Catalogue Manual - SN 1001 AND U...han647runken
This document provides parts information for an HM350-1 excavator with serial numbers 1001 and up. It includes a list of major systems and subsystems for the excavator. For each part listed, it provides the part number, name, quantity, and applicable serial number range. The document contains detailed parts listings for various engine and cooling system components.
Komatsu HM300-3 Articulated Dump Truck Parts Catalogue Manual - SN 3001 AND U...han647runken
This document provides parts information for an HM300-3 excavator with serial numbers 3001 and up. It includes sections for the engine, cooling system, fuel system, electrical system, and other components. The cooling system section lists units for the radiator, aftercooler, coolant piping, brake oil cooler, and brake oil cooler piping. Parts are identified by index number, part number, description, and quantity for each component. The document provides an exploded diagram and parts list for each assembly.
Komatsu HM300-2 Articulated Dump Truck Parts Catalogue Manual - SN 2001-2784.pdfhan647runken
This document contains parts lists and specifications for various engine and drivetrain components of an HM300-2 excavator with serial number 2001-2784. It includes 17 sections with details on the engine mounting, hoses, piping, air conditioning parts, damper, and other related systems. The document provides part numbers, names, quantities and serial number ranges for each component listed.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...han647runken
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to more detailed parts pages for items like the engine mounting, hoses, piping, harness, damper, air cleaner, and other engine components. Parts are identified by number, description, and quantity.
Komatsu D155C-1 Pipe Layer Parts Catalogue Manual - SN 15686 AND UP.pdfhan647runken
This document provides parts information for a D155C-1 excavator with a SA6D140-2 engine installed. It includes lists of parts for the engine and its related systems, including the cooling system, fuel tank and piping, and electrical system. The parts are organized by section and item number, and each part includes its number, name, quantity, and applicable serial number range.
Deutz Fahr AGROTRON 265 Tractor Service Repair Manual.pdfhan647runken
This workshop manual provides safety instructions for working on Agrotron tractors. It stresses the importance of following prescribed repair procedures using the proper tools. Personal safety should always take priority over work tasks. Specific safety precautions are outlined for different repair operations like removing and refitting parts, working with batteries and electrical systems, and using lifting equipment. Proper protective equipment and ventilation are required, and precautions are described to prevent injury from moving parts, hot surfaces, chemicals, and other hazards.
Deutz Fahr AGROTRON 235 Tractor Service Repair Manual.pdfhan647runken
This workshop manual provides safety instructions for working on Agrotron tractors. It stresses the importance of following prescribed repair procedures using the proper tools. Personal safety should always take priority, and potentially dangerous work should involve two people. Specific safety precautions are outlined for different repair tasks, including wearing protective equipment, lifting heavy components safely, and working with high-pressure systems and batteries. Proper techniques like using support stands and following torque specifications are emphasized to prevent injury and ensure correct reassembly.
Deutz Fahr AGROTRON 210 Tractor Service Repair Manual.pdfhan647runken
This workshop manual provides safety instructions for working on Agrotron tractors. It stresses the importance of following prescribed repair procedures using the proper tools. Personal safety should always take priority, and potentially dangerous work should involve two people. Specific safety precautions are outlined for different repair tasks, including wearing protective equipment, lifting heavy components safely, and working with high-pressure systems and batteries. Proper techniques like using support stands and following torque specifications are emphasized to prevent injury and ensure correct reassembly.
Deutz Fahr AGROFARM 100 Tractor Service Repair Manual.pdfhan647runken
This document provides the table of contents for a workshop manual for Agrofarm 85 and Agrofarm 100 tractors. The manual covers technical specifications, calibrations and electronic diagnosis, maintenance and repair methods, and wiring diagrams. It includes sections on the engine, transmission, axles, hydraulics, bodywork and more. The table of contents lists over 30 sections and subsections that provide information, part numbers, and instructions for repair and maintenance of components.
Deutz Fahr AGROFARM 85 Tractor Service Repair Manual.pdfhan647runken
This document provides the table of contents for a workshop manual for Agrofarm 85 and Agrofarm 100 tractors. The manual covers technical specifications, calibrations and electronic diagnosis, maintenance and repair methods, and wiring diagrams. It includes sections on the engine, transmission, axles, hydraulics, bodywork and more. The table of contents lists over 30 sections and subsections that provide information, part numbers, and instructions for repair and maintenance of components.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 973C TRACK LOADER BCP
Configuration: 973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
973C Track-Type Loader Powertrain
Media Number -RENR8206-01 Publication Date -01/04/2010 Date Updated -28/04/2010
i02165395
Hydrostatic Drive Oil Tank - Remove and Install
SMCS - 5056-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Start By:
A. Remove the cab. Refer to Disassembly and Assembly, "Cab - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1. Drain the oil tank for the hydrostatic drive into a suitable container. Refer to Operation and
Maintenance Manual, "Capacities - Refill" for the capacity of the tank.
Illustration 1 g01094830
2. Disconnect hose assembly (1) .
2/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01094924
3. Disconnect hose assemblies (3) and hose assemblies (5) from block (4). Disconnect clip (6)
from tank assembly (2) .
3/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01094928
4. Disconnect hose assemblies (7) from tank assembly (2) .
4/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01094940
5. Attach Tooling (A) and a suitable lifting device to tank assembly (2). Remove bolts (8), the
washers, and the mounting from tank assembly (2). Remove bolts (9), the washers, and the
mounting from tank assembly (2). Remove bolts (11), the washers, and the mounting from
tank assembly (2). Disconnect harness assembly (10) from the bottom of tank assembly (2) .
6. Remove tank assembly (2) from the machine. The weight of tank assembly (2) is
approximately 34 kg (75 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
5/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g01094940
1. Attach Tooling (A) and a suitable lifting device to tank assembly (2) and position tank
assembly (2) to the machine. The weight of tank assembly (2) is approximately 34 kg (75
6/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. lb). Install bolts (8), the washers, and the mounting to tank assembly (2). Install bolts (9),
the washers, and the mounting to tank assembly (2). Install bolts (11), the washers, and the
mounting to tank assembly (2). Connect harness assembly (10) to the bottom of tank
assembly (2) .
Illustration 6 g01094928
2. Connect hose assemblies (7) to tank assembly (2) .
7/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 7 g01094924
3. Connect hose assemblies (3) and hose assemblies (5) to block (4). Connect clip (6) to tank
assembly (2) .
8/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 8 g01094830
4. Connect hose assembly (1) .
5. Refill the oil tank for the hydrostatic drive. Refer to Operation and Maintenance Manual,
"Capacities - Refill" for the capacity of the tank.
End By: Install the cab. Refer to Disassembly and Assembly, "Cab - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 15:22:28 UTC+0800 2019
9/9
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 973C TRACK LOADER BCP
Configuration: 973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
973C Track-Type Loader Powertrain
Media Number -RENR8206-01 Publication Date -01/04/2010 Date Updated -28/04/2010
i02154475
Pump Drive - Remove
SMCS - 3108-011-PD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 8T-5255 Hydraulic Jack 1
Start By:
A. Remove the hydraulic drive pumps. Refer to Disassembly and Assembly, "Hydraulic Drive
Pump - Remove".
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/11
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01092358
1. Disconnect hose assembly (1) and tube assembly (1A) .
2/11
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g01092364
2. Attach a suitable lifting device to implement pump (2). Remove bolts (3) and remove
implement pump (2) and the O-ring seal. The weight of implement pump (2) is
approximately 45 kg (100 lb).
3/11
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g01092383
6. Attach Tooling (A) and a suitable lifting device to filter group (12). Remove bolts (13) and
remove filter group (12). The weight of filter group (12) is approximately 25 kg (55 lb).
7/11
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 10. Position Tooling (B) under flywheel housing (23) in order to support the rear of the engine.
11. Disconnect harness assembly (24). Remove bolts (22) .
Illustration 11 g01092409
12. Attach Tooling (A) and a suitable lifting device to pump drive (25). Remove bolts (26) and
remove pump drive (25). The weight of pump drive (25) is approximately 227 kg (500 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 15:23:17 UTC+0800 2019
11/11
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 973C TRACK LOADER BCP
Configuration: 973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
973C Track-Type Loader Powertrain
Media Number -RENR8206-01 Publication Date -01/04/2010 Date Updated -28/04/2010
i02149030
Pump Drive - Disassemble
SMCS - 3108-015-PD
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-3822 Forcing Bolts, M10 x 1.5 by 35mm 3
B 138-7575 Link Bracket 3
C
1P-0074 Slide Hammer 1
5F-7342 Adapter 1
D 8B-7551 Bearing Puller 1
E 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the pump drive. Refer to Disassembly and Assembly, "Pump Drive - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01090142
1. Remove bolts (1) from housing assembly (2) .
2/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 2 g00939458
2. Remove shut off valve (5) .
3. Use Tooling (A) to separate cover (3) from housing (4) .
Illustration 3 g00979712
3/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 4. Install Tooling (B) and a suitable lifting device to cover (3). Remove cover (3). The weight
of cover (3) is approximately 66 kg (145 lb).
Illustration 4 g00979705
5. Use Tooling (C) to remove seal (6) .
6. Remove ring (7). Use Tooling (E) in order to remove retaining rings (8). Remove bearing
cups (9) .
4/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00979706
7. Mark the location of drive gears (10) for assembly purposes. Remove drive gears (10) .
8. Remove temperature sending unit (11) .
5/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 6 g00939459
9. Tooling (D) may be used for the removal of bearing cones (12), if necessary.
6/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 7 g01090206
10. Remove bearing cups (13) from housing (4) .
11. Remove seal (14) with Tooling (C) .
12. Remove vent (15) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 15:24:06 UTC+0800 2019
7/7
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine(S...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...