This document provides instructions for assembling an alternator. It describes 27 steps to assemble components like diodes, bushings, bearings, coils, and housings. It notes that cleanliness is important and components should be cleaned before assembly. It also warns not to strike delicate parts like diodes or bearings during assembly to avoid damage. The document includes diagrams illustrating each step of the assembly process.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, caps, and housing pieces. Cleanliness is emphasized throughout assembly and notes provide warnings about not damaging delicate parts like diodes, bearings, and windings.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, caps, and housing pieces. Cleanliness is emphasized throughout assembly and notes provide warnings about not damaging delicate parts like diodes, bearings, and windings.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized throughout assembly and notes provide warnings about damaging parts during pressing or striking.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and leads. For the turbocharger, it outlines 14 steps to disassemble it by removing housings, wheels and seals. It then lists 15 steps for reassembling the turbocharger, including installing new seals, bearings and ensuring oil passages are clean.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housings and ends by connecting wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals, and 13 steps to reassemble it, such as installing bearings, seals and housings. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and connects wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals. Reassembly involves installing new seals, bearings and pressing components back together in the correct orientation. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together, and ending by connecting wires and installing covers. It also provides 5 steps to remove an air cleaner housing and 4 steps to install it. Finally, it lists 14 steps to disassemble a turbocharger, such as removing housings and wheels, and 13 steps to reassemble it, including installing bearings and seals. Cleanliness is emphasized throughout assembly.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together, and ending by connecting wires and installing covers. It also describes removing and installing an air cleaner housing in 5 steps each. Finally, it lists 14 steps to disassemble a turbocharger, such as removing the compressor wheel and turbine shroud, and 13 steps to reassemble it, including installing bearings and seals. Cleanliness is emphasized throughout assembly.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It describes in detail the 29 steps to assemble the alternator, including pressing components together and connecting wires. It also describes removing and installing the turbocharger and air cleaner housing, as well as the 15 steps to disassemble and 13 steps to reassemble the turbocharger, noting the use of marks and grease during assembly.
This document provides assembly instructions for an alternator and turbocharger. It includes 29 steps to assemble the alternator, ensuring cleanliness and proper installation of components like diodes, coils, housings and terminals. It also details 15 steps to disassemble and 13 steps to reassemble a turbocharger, including marking parts for alignment and applying anti-seize compound to bolts during installation. Cleanliness and correct orientation of parts like bearings and seals are emphasized.
This document provides assembly instructions for an alternator and turbocharger. It includes 29 steps to assemble the alternator, ensuring cleanliness and proper installation of components like diodes, coils, housings and terminals. It also details 15 steps to disassemble and 13 steps to reassemble a turbocharger, including installation of bearings, seals, wheels and housings. Proper positioning and torque values are emphasized throughout.
This document provides assembly and disassembly instructions for servicing an alternator and turbocharger on a Caterpillar 963 track loader. It describes in detail the 29 steps to assemble the alternator, including pressing components together and installing screws, bolts and wires in the proper order. It also outlines removing and installing the air cleaner housing and turbocharger, noting parts like gaskets, lines, elbows and clamps. Disassembly of the turbocharger is described as removing housing components and using positioning tools.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
More Related Content
Similar to Caterpillar Cat 963 TRACK LOADER (Prefix 48Z) Service Repair Manual Instant Download (48Z00232).pdf
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized throughout assembly and notes provide warnings about damaging parts during pressing or striking.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and leads. For the turbocharger, it outlines 14 steps to disassemble it by removing housings, wheels and seals. It then lists 15 steps for reassembling the turbocharger, including installing new seals, bearings and ensuring oil passages are clean.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housings and ends by connecting wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals, and 13 steps to reassemble it, such as installing bearings, seals and housings. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and connects wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals. Reassembly involves installing new seals, bearings and pressing components back together in the correct orientation. Proper cleaning and lubrication of parts is emphasized throughout.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together, and ending by connecting wires and installing covers. It also provides 5 steps to remove an air cleaner housing and 4 steps to install it. Finally, it lists 14 steps to disassemble a turbocharger, such as removing housings and wheels, and 13 steps to reassemble it, including installing bearings and seals. Cleanliness is emphasized throughout assembly.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together, and ending by connecting wires and installing covers. It also describes removing and installing an air cleaner housing in 5 steps each. Finally, it lists 14 steps to disassemble a turbocharger, such as removing the compressor wheel and turbine shroud, and 13 steps to reassemble it, including installing bearings and seals. Cleanliness is emphasized throughout assembly.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It describes in detail the 29 steps to assemble the alternator, including pressing components together and connecting wires. It also describes removing and installing the turbocharger and air cleaner housing, as well as the 15 steps to disassemble and 13 steps to reassemble the turbocharger, noting the use of marks and grease during assembly.
This document provides assembly instructions for an alternator and turbocharger. It includes 29 steps to assemble the alternator, ensuring cleanliness and proper installation of components like diodes, coils, housings and terminals. It also details 15 steps to disassemble and 13 steps to reassemble a turbocharger, including marking parts for alignment and applying anti-seize compound to bolts during installation. Cleanliness and correct orientation of parts like bearings and seals are emphasized.
This document provides assembly instructions for an alternator and turbocharger. It includes 29 steps to assemble the alternator, ensuring cleanliness and proper installation of components like diodes, coils, housings and terminals. It also details 15 steps to disassemble and 13 steps to reassemble a turbocharger, including installation of bearings, seals, wheels and housings. Proper positioning and torque values are emphasized throughout.
This document provides assembly and disassembly instructions for servicing an alternator and turbocharger on a Caterpillar 963 track loader. It describes in detail the 29 steps to assemble the alternator, including pressing components together and installing screws, bolts and wires in the proper order. It also outlines removing and installing the air cleaner housing and turbocharger, noting parts like gaskets, lines, elbows and clamps. Disassembly of the turbocharger is described as removing housing components and using positioning tools.
Similar to Caterpillar Cat 963 TRACK LOADER (Prefix 48Z) Service Repair Manual Instant Download (48Z00232).pdf (18)
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
This document provides instructions for removing and installing the camshaft on a Caterpillar 3412C engine. Key steps include:
1. Removing the front housing, lifter group, and flywheel housing.
2. Removing four bolts and a plate from the rear of the camshaft and removing the camshaft gear.
3. Aligning timing marks and removing two bolts and a plate from the camshaft.
4. Removing the camshaft from the cylinder block and optionally removing the camshaft gear using a driver group tool.
This service repair manual provides instructions for removing and installing the flywheel housing and rear power take-off (RPTO) on a Caterpillar 657G wheel tractor. The flywheel housing removal procedure involves removing bolts and seals, then lifting the housing off using lifting brackets. Installation involves cleaning parts, applying sealant, positioning seals and gaskets, and tightening bolts in a specific sequence. The RPTO removal procedure describes removing gears, idlers, retainers, sleeves and covers. Installation involves cleaning, lubricating, and positioning these parts before securing with bolts.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing O-rings, bolts, bearings, and shaft components.
This document provides instructions for installing a crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes cleaning and applying retaining compound to the crankshaft and wear sleeve. A locator is installed on the crankshaft to position the wear sleeve and seal, which are then installed using an installer tool. Finally, the installer is removed and bolts are tightened to complete the installation.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including gears, shafts, bearings, and seals. The assembly process describes installing these components in 23 steps, noting proper orientation and torque specifications. Tools required include various pullers, presses, and forcing screws.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hydraulic and electrical connections, draining fluid from the elbow, attaching a lifting device to the pump, and removing mounting nuts and the pump. Cleaning parts and plugging lines is noted for prevent contamination during removal.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Removing the flywheel by using bolting brackets to hold the crankshaft gear, installing guide bolts, and lifting the flywheel off with a hoist.
- Reinstalling components by pressing bearings into place with drives, torquing bolts, and checking runout after installing the flywheel.
The document provides detailed step-by-step instructions accompanied by illustrations of the disassembly and
This document provides instructions for installing and removing the crankshaft rear seal on a Caterpillar 657E wheel scraper. The removal procedure involves using a punch or slide hammer puller to puncture and remove the existing seal. The installation procedure specifies using a seal installer tool and retaining compound to press the new seal and wear sleeve onto the crankshaft. Precautions are given to keep the components clean and not reuse a separated seal and sleeve. The instructions are illustrated with diagrams and apply to both engine configurations with and without a rear gear train.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 651E wheel scraper. The removal procedure involves using various tools to disassemble the adapter assemblies, gears, bearings and other components. The installation procedure describes cleaning and lubricating parts, pressing or installing bearings and gears back into place, and reassembling the components in reverse order. Precautions are given to keep parts clean and lubricated to prevent wear.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including the housing assembly, torque converter assembly, impeller wheel assembly, carrier assembly, and stator assembly. It then describes assembling the torque converter in 25 steps by installing the parts in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and slide hammers.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...9fikslkddmd8u
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...9fikslkddmd8u
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing components like the camshaft gear and rocker arms first. Tools like a cradle, guide, camshaft pilots and hooks are then used to support the camshaft as it is moved out of the cylinder head and into the guide. Care must be taken to avoid damaging the camshaft or bearings during removal.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order, noting to keep parts clean and apply Loctite to the threaded rod.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 963 TRACK LOADER 48Z
Configuration: 963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
26SI Series Alternator
Media Number -RENR1252-01 Publication Date -01/10/1999 Date Updated -09/10/2001
i01167078
Alternator - Assemble
SMCS - 1405-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Do not strike the diodes. The shock of such an impact can damage the diodes. Use
proper tools in order to press the diodes in the mountings.
Illustration 1 g00628072
1. Install 3 diodes (11) in heat sink (12) .
1/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00628068
Note: Do not strike the bushing. Shocks from striking the housing can cause damage.
2. Press bushing (43) in housing (14) .
3. Install 3 diodes (13) in housing (14) .
Illustration 3 g00628067
4. Press collar (42) on rotor (39) .
5. Slide retainer (41) on rotor (39) .
6. Press bearing (40) on rotor (39) .
2/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00628063
7. Press housing (31) on rotor (39) and bearing (40) .
8. Install 4 screws (38) in housing (31) .
Illustration 5 g00628057
Note: Do not strike the bearing. Shocks from striking the housing can cause damage.
9. Install the inner race. Press bearing (37) into the housing.
3/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00628043
10. Press cap (36) in housing (14) .
Illustration 7 g00628041
11. Install the coil and support (34) in housing (14). Guide the field leads and the grommet
through the hole as the coil is installed in housing (14). Install 3 screws (33) .
Illustration 8 g00628037
12. Press the stator (32) and housing (14) together. Guide the stator leads and the grommet
through the hole as the stator is installed in housing (14) .
4/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00628035
Note: Do not damage exposed stator windings or field windings. Bumping the windings or
scraping the windings may break the insulation. Broken insulation may create a short circuit
or a ground.
13. Join housing (31) and housing (14). Install 4 bolts (30) .
Illustration 10 g00627853
Note: Many of the alternator's internal components are covered with dielectric grease. If the
grease is removed, reapply the grease.
5/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00627855
14. Install Insulator (29). Install the heat sink and diode assembly (12) in housing (14) .
Illustration 12 g00627840
15. Install separator (28) .
16. Install alternator output terminal (27). Install insulator (26). Install the nut and washer (25) .
17. Install diode trio (24) and install screw (23) .
6/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00627832
18. Install the 3 screws and insulators (18). Connect wire (19) .
19. If the "R" terminal is used, install the following components: nut (20), lead (21), the washer
and terminal (21) .
Illustration 14 g00627820
20. Install the screw and insulator (16). Connect capacitor lead (17) .
Illustration 15 g00627810
Note: The 3 output diodes (11) are located in heat sink (12). These diodes are identical in
polarity. Diode (11) has red insulation on the wire. The 3 ground diodes (13) are located in
housing (14). These diodes are identical in polarity. Diode (13) has black insulation on the
wire.
21. Connect 6 diode leads. Connect 3 phase leads. Connect 3 stator phase leads. Install 3 nuts
(15).
Table 1
7/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Alternator
Ground
Current Flow of the Output
Diodes
Current Flow of the Ground
Diodes
Negative
Lead to the Heat Sink Housing to the Lead
Red Wire Black Wire
Illustration 16 g00627808
22. Install mounting plate (10).
Illustration 17 g00627804
23. Install regulator (9) .
24. Install grounded mounting screw (8) .
8/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00627796
25. Install 2 insulated screws (6). Connect the 3 leads.
Note: The regulator and the mounting plate are coated with dielectric grease. If the grease is
removed, reapply the grease.
26. Install nut (7) and connect the wire.
Illustration 19 g00627794
27. Install gasket (5) .
9/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00627792
28. Position cover (4). Install 7 screws (3) .
Illustration 21 g00627790
29. Position plate (2). Install 4 screws (1) .
30. Install the fan, the pulley, the washer, and the pulley nut.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 16 11:41:58 UTC+0800 2019
10/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 E...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 963 TRACK LOADER 48Z
Configuration: 963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
963 TRACK-TYPE LOADER
Media Number -SENR2284-00 Publication Date -01/07/1981 Date Updated -11/10/2001
Air Cleaner Housing
SMCS - 1051-11; 1051-12
Remove Air Cleaner Housing
1. Remove cover (1) from the air cleaner housing.
2. Remove primary filter element (2).
3. Remove eight bolts (3) and secondary filter element (4) from the filter housing.
1/3
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Loosen clamp (5) on the rubber air line to the air cleaner.
5. Remove two nuts (6) and air cleaner housing (7).
Install Air Cleaner Housing
1. Put the gasket and air cleaner housing (2) in position on the air inlet pipe and install the nuts
that hold it in place.
2. Put rubber air line (1) from the precleaner in position on the air cleaner housing and tighten the
clamp to hold it in place.
3. Put secondary filter element (3) in position in the air cleaner housing and install the eight bolts
that hold it in place.
2/3
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Install primary filter element (4).
5. Install the cover on the air cleaner housing and tighten clamp bolts (5) finger tight only. Do not
use a tool to tighten the clamp bolts.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 16 11:44:46 UTC+0800 2019
3/3
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 963 TRACK LOADER 48Z
Configuration: 963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
963 TRACK-TYPE LOADER
Media Number -SENR2284-00 Publication Date -01/07/1981 Date Updated -11/10/2001
Turbocharger
SMCS - 1052-11; 1052-12; 1052-15; 1052-16
Remove Turbocharger
1. Remove turbocharger oil inlet line (1) and outlet line (2).
2. Remove the bolts that hold exhaust elbow (3) to the exhaust manifold and move the exhaust
elbow and coupling (4) clear of the turbocharger.
3. Loosen clamp (5) on the turbocharger air outlet and clamp (6) on the turbocharger air inlet.
1/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 4. Remove four bolts (7). Remove turbocharger (8) from the exhaust manifold and air lines.
Install Turbocharger
1. Install a new gasket (1) if necessary.
2. Put the turbocharger in position on the exhaust manifold and air lines. Put 5P3931 Anti-Seize
Compound on the threads of the bolts that hold the turbocharger to the exhaust manifold. Tighten
the bolts to the standard torque.
3. Put the clamps in position on air lines (2) and tighten them.
4. Put coupling (3) and exhaust elbow (4) in position on the turbocharger and exhaust manifold. Put
5P3931 Anti-Seize Compound on the threads of the bolts that hold the exhaust elbow to the exhaust
manifold. Tighten the bolts to the standard torque.
2/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 5. Install the gaskets and turbocharger oil outlet line (5) and oil inlet line (6).
Disassemble Turbocharger
start by:
a) remove turbocharger
1. Put the turbocharger in position tool (A).
2. Put a mark on compressor housing (1) and the backplate assembly for use at assembly. Remove
the compressor housing from the backplate assembly.
3. Change the position of tool (A) so the compressor wheel is up as shown.
4. Put a mark on housing (2) and turbine housing (3) so that the housing can be put back in the same
position in the turbine housing at assembly.
3/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 5. Remove the bolts, lockplates and clamps that hold the housing in the turbine housing and remove
the housing.
6. Put the housing in position on tool (B).
7. Use tool (C) and a socket of the correct size to remove nut (5) from the shaft.
NOTICE
Do not put a side force on the shaft when the nut is removed.
8. Remove compressor wheel (4) from the shaft.
9. Remove the housing from the shaft.
10. Remove shroud (6) from the turbine wheel and shaft.
11. Remove seal ring (7) from the turbine wheel.
12. Put a mark on the housing and backplate assembly for use at assembly. Remove the bolts and
plates that hold the housing to the backplate assembly. Remove the housing.
4/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 13. Remove bearing (8), collar (9) and the seal ring from backplate assembly (10).
14. Remove the seal ring and bearing from the collar.
15. Remove seal ring (11) from the housing.
16. Remove the snap ring, bearing (12) and the snap ring from each side of the housing.
Assemble Turbocharger
1. Make sure all oil passages are clean and free of all dirt or foreign material. Put clean engine oil on
all of the parts before assembly.
2. Install the inner snap ring, bearing (1) and snap ring (2) in each side of the housing.
NOTE: The snap rings must be installed with the round side toward the bearing.
5/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 3. Install the seal ring on collar (4).
4. Put bearing (3) in position on the collar.
NOTICE
The oil grooves in the bearing must be clean and free of all dirt or
foreign material. The bearing must be installed with the oil grooves
toward the housing.
5. Put the bearing and collar in position on the housing so the oil grooves in the bearing are toward
the housing and the holes in the bearing are in alignment with the pins in the housing.
NOTICE
Be extra careful during installation of the bearing and collar not to
cause damage to the seal ring on the collar.
6. Install the seal ring on the housing.
7. Put the backplate assembly in position on the housing respective to the marks put on the housing
and backplate at disassembly. Install the plates and bolts. Tighten the bolts to a torque of 8.5 - 10.2
N·m (75 - 90 lb.in.).
8. Install shroud (5) on the housing.
6/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 9. Put 6V2055 High Vacuum Grease in the groove for seal ring (7). Make sure the grease fills the
groove approximately one half or more of the groove depth for the complete circumference of the
groove to help make a carbon dam under the seal. Install seal ring (7). Carefully install turbine
wheel and shaft (6) in the housing.
10. Put the housing, turbine wheel and shaft and the backplate assembly in position on tool (A).
11. Install compressor wheel (8) on the turbine shaft.
12. Put clean engine oil on the threads of the shaft. Install the nut that holds the compressor wheel in
place. Tighten the nut with tool (D) to a torque of 2.3 N·m (20 lb.in.). Put a mark on the nut and
shaft. Tighten the nut 100° more.
NOTICE
When the nut is tightened, do not put a side force on the shaft.
7/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 13. If the turbine housing was removed from tool (B), put the turbine housing in position on tool
(B).
14. Put the housing and wheels in position in the turbine housing respective to the marks put on the
housings at disassembly.
15. Put 5P3931 Anti-Seize Compound on the threads of bolts (9). Install the clamps, lockplates and
the bolts (9). Tighten the bolts to a torque of 13 ± 1.7 N·m (115 ± 15 lb.in.). Bend the lockplates
against the bolt heads.
16. Put compressor housing (10) in position on the backplate assembly respective to the marks put
on the housing and backplate assembly at disassembly.
17. Install the clamps, lockplates and bolts that hold the compressor housing in place. Tighten the
bolts to a torque of 13 ± 1.7 N·m (115 ± 15 lb.in.). Bend the lockplates against the bolt heads.
18. Remove the turbocharger from tool (B).
NOTE: If new components have been installed at assembly and the correct position for the turbine
housing or compressor housing is not known, put the housings in their correct position with the
9S9143 Gauge Group. A line through the center of the openings in the turbine housing and
compressor housing must be at the angle shown. See SPECIAL INSTRUCTIONS FORM
GMG00579.
end by:
a) install turbocharger
8/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 9/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 16 11:45:36 UTC+0800 2019
10/10
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 E...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 963 TRACK LOADER 48Z
Configuration: 963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
963 TRACK-TYPE LOADER
Media Number -SENR2284-00 Publication Date -01/07/1981 Date Updated -11/10/2001
Muffler And Hood
SMCS - 1062; 7251-11; 7251-12
Remove Muffler And Hood
1. Loosen clamp (1) and disconnect the exhaust pipe from the muffler.
2. Remove the bolts that hold muffler (2) to the hood and remove the muffler.
3. Remove precleaner (3).
1/3
963 TRACK TYPE LOADER 48Z00232-UP (MACHINE) POWERED BY 3304 EN...
2019/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...